Search NASA⌕ Search

SEARCH · Search NASA

Results for “Coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Improved damage tolerance of SiC-based nuclear fuel cladding with novel multi-layered SiC coating design at 1200 °C

Continuous SiC fibre reinforced SiC matrix composites (SiC f -SiC m ) with monolithic SiC outer coatings are considered as a damage-tolerant cladding design for loss of coolant accident (LOCA) conditions in light water reactors. However, monolithic SiC coatings are brittle and prone to catastrophic failure. In this study, a SiC f -SiC m cladding with a novel multi-layer SiC outer coating (11 sub-layers, ∼260 µm in total thickness) was investigated under C-ring compression at room temperature and 1200 °C in argon environment. Real-time synchrotron X-ray computed tomography (XCT) was employed to capture crack initiation and propagation processes. Compared to conventional monolithic SiC outer coatings, the multi-layer coating structure facilitated crack deflection and bifurcation enhancing its damage tolerance at both temperatures. Despite pre-existing surface cracks, claddings exhibited stable mechanical-performance at both temperatures. These initial cracks did not critically affect the failure processes as they were not aligned with the maximum stress direction. Furthermore, the microstructure, distribution of residual stresses, and local properties of individual components in the material were thoroughly characterized, and compared with open literature on conventional claddings with monolithic outer coatings. These results provide new insights into the failure mechanisms of multi-layer SiC coatings and offer guidance for the future design of accident-tolerant nuclear fuel claddings.

36 - MATERIALS SCIENCE↗

Process and properties of electroless Ni-Cu-P-ZrO{sub 2} nanocomposite coatings

Highlights: Black-Right-Pointing-Pointer The Ni-P and Ni-P-Cu-ZrO{sub 2} coatings were produced by electroless technique. Black-Right-Pointing-Pointer The influence of copper and ZrO{sub 2} nanoparticles on Ni-P was studied. Black-Right-Pointing-Pointer Surface morphology, structure and electrochemical behavior were evaluated. Black-Right-Pointing-Pointer The Ni-Cu-P-ZrO{sub 2} and Ni-P-ZrO{sub 2} coatings are more resistant to corrosion than Ni-P. Black-Right-Pointing-Pointer Introduction of Cu and ZrO{sub 2} in the matrix aids to the enhancement of microhardness. -- Abstract: Electroless Ni-Cu-P-ZrO{sub 2} composite coating was successfully obtained on low carbon steel matrix by electroless plating technique. Coatings with different compositions were obtained by varying copper as ternary metal and nano sized zirconium oxide particles so as to obtain elevated corrosion resistant Ni-P coating. Microstructure, crystal structure and composition of deposits were analyzed by SEM, EDX and XRD techniques. The corrosion behavior of the deposits was studied by anodic polarization, Tafel plots and electrochemical impedance spectroscopy (EIS) in 3.5% sodium chloride solution. The ZrO{sub 2} incorporated Ni-P coating showed higher corrosion resistance than plain Ni-P. The introduction of copper metal into Ni-P-ZrO{sub 2} enhanced the protection ability against corrosion. The influence of copper metal and nanoparticles on microhardness of coatings was evaluated.

36 MATERIALS SCIENCE↗

Effects of alpha-zirconium phosphate on thermal degradation and flame retardancy of transparent intumescent fire protective coating

Graphical abstract: - Highlights: • A transparent intumescent fire protective coating was obtained by UV-cured technology. • OZrP could enhance the thermal stability and anti-oxidation of the coating. • OZrP could reduce the combustion properties of the coatings. - Abstract: Organophilic alpha-zirconium phosphate (OZrP) was used to improve the thermal and fire retardant behaviors of the phenyl di(acryloyloxyethyl)phosphate (PDHA)-triglycidyl isocyanurate acrylate (TGICA)-2-phenoxyethyl acrylate (PHEA) (PDHA-TGICA-PHEA) coating. The morphology of nanocomposite coating was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The effect of OZrP on the flame retardancy, thermal stability, fireproofing time and char formation of the coatings was investigated by microscale combustion calorimeter (MCC), thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), laser Raman spectroscopy (LRS) and scanning electric microscope (SEM). The results showed that by adding OZrP, the peak heat release rate and total heat of combustion were significantly reduced. The highest improvement was achieved with 0.5 wt% OZrP. XPS analysis indicated that the performance of anti-oxidation of the coating was improved with the addition of OZrP, and SEM images showed that a good synergistic effect was obtained through a ceramic-like layer produced by OZrP covered on the surface of char.

36 MATERIALS SCIENCE↗

Synthesis and characterization of carbon-coated Fe{sub 3}O{sub 4} nanoflakes as anode material for lithium-ion batteries

Graphical abstract: - Highlights: • Carbon-coated Fe{sub 3}O{sub 4} nanoflakes have been synthesized by hydrothermal method. • The nanocomposite electrode shows a large reversible capacity up to 740 mAh g{sup −1}. • The nanocomposite electrode shows promising cycling stability and rate capability. - Abstract: The carbon-coated Fe{sub 3}O{sub 4} nanoflakes were synthesized by partial reduction of monodispersed hematite (Fe{sub 2}O{sub 3}) nanoflakes with carbon coating. The carbon-coated Fe{sub 3}O{sub 4} nanoflakes were characterized by X-ray diffraction, Raman spectroscopy, field emission scanning electron microscopy, transmission electron microscopy, and galvanostatic charge/discharge measurements. It has been demonstrated that Fe{sub 2}O{sub 3} can be completely converted to Fe{sub 3}O{sub 4} during the reduction process and carbon can be successfully coated on the surface of Fe{sub 3}O{sub 4} nanoflakes, forming a conductive matrix. As anode material for lithium-ion batteries, the carbon-coated Fe{sub 3}O{sub 4} nanoflakes exhibit a large reversible capacity up to 740 mAh g{sup −1} with significantly improved cycling stability and rate capability compared to the bare Fe{sub 2}O{sub 3} nanoflakes. The superior electrochemical performance of the carbon-coated Fe{sub 3}O{sub 4} nanoflakes can be attributed to the synthetic effects between small particle size and highly conductive carbon matrix.

36 MATERIALS SCIENCE↗

Residual stresses in functionally graded thermal barrier coatings

Functionally graded materials offer potential as a solution to the premature failure of thermal barrier coatings due to thermal residual stresses, however this solution has not been fully evaluated to date. An analytical methodology based on the bending of plates has been used to model the residual stress distribution through the layers of a functionally graded (FG) cermet top coat-bond layer-substrate system after cooling from a high deposition temperature. The model is then applied to two material systems with different trends in variation in the coefficient of thermal expansion from the substrate to the top coat layer. Increasing the number of layers reduces the discrete stress variations across the interfaces through the FG layers and reduces the propensity of interfacial cracking. While the stress in the top coat is always compressive for the Inconel substrate, the stress in the top coat is tensile in nature for the steel substrate when the ceramic volume fraction in the functionally graded layers is low. The stress in the top coat gradually becomes compressive with an increasing volume fraction of ceramic in the functionally graded top coat. The curvature of the TBC system follows a similar trend and changes its sign with increasing ceramic content for the steel substrate. In conclusion, the effect of the number of layers on the curvature gradually diminishes and the curvature becomes constant beyond only a few layers.

36 MATERIALS SCIENCE↗

Potassium Prussian blue-coated Li-rich cathode with enhanced lithium ion storage property

With high specific capacity, the layered Li-rich Mn-based oxide (LRMO) is a promising candidate cathode material for Li-ion batteries. However, the irreversible release of Li-ions during the first charging process, instability of LRMO/electrolyte interface and relatively low ion conductivity of LRMO result in low initial Coulombic efficiency (ICE), poor cycle stability and rate performance, which prohibit its further application. Furthermore, interface engineering via additive coating is expected to effectively address these issues. Herein, we rely on potassium Prussian blue (KPB), a Li + acceptor with good ion conductivity, as a new coating material on LRMO particles. The KPB coating not only forms a protective layer on the surface of LRMO against electrolyte corrosion, but also functions as a host for Li + transport and accommodation, leading to enhanced ion conductivity and ICE of LRMO cathode. Consequently, 2 wt% KPB coated LRMO cathode achieved an initial discharge capacity of up to 281.7 mA h g -1 with an ICE of 85.69% compared to an ICE of 79.52% for the LRMO cathode without coating. The cycling and rate performance are also greatly improved as evidenced by the well maintained capacity of up to 176.8 mA h g -1 after 100 cycles at a current density of 0.5 C, compared to the limited capacity of only 135.3 mA h g -1 for the LRMO cathode without coating. Overall, this work pioneers the use of potassium Prussian blue as additive coating material to enhance performance of LRMO cathode, and we expect it to inspire the battery community with new strategies of material engineering/design toward practical application in high-energy lithium-ion batteries.

25 ENERGY STORAGE↗

Measurement of spin-flip probabilities for ultracold neutrons interacting with nickel phosphorus coated surfaces

In this paper, we report a measurement of the spin-flip probabilities for ultracold neutrons interacting with surfaces coated with nickel phosphorus. For 50 μm thick nickel phosphorus coated on stainless steel, the spin-flip probability per bounce was found to be β NiP on SS = (3.3 +1.8, -5.6) X 10 -6 . For 50 μm thick nickel phosphorus coated on aluminum, the spin-flip probability per bounce was found to be β NiP on Al = (3.6 +2.1, -5.9) X 10 -6 . For the copper guide used as reference, the spin flip probability per bounce was found to be β Cu = (6.7 + 5.0, -2.5) X 10 -6 . The results on the nickel phosphorus-coated surfaces may be interpreted as upper limits, yielding β NiP on SS < 6.2 X 10 -6 (90% C.L.) and β NiP on Al < 7.0 X 10 -6 (90% C.L.) for 50 μm thick nickel phosphorus coated on stainless steel and 50 μm thick nickel phosphorus coated on aluminum, respectively. Finally, nickel phosphorus coated stainless steel or aluminum provides a solution when low-cost, mechanically robust, and non-depolarizing UCN guides with a high Fermi potential are needed.

36 MATERIALS SCIENCE↗

Effects on J c of Pinning Center Morphology for Multiple-in-Line-Damage in Coated Conductor and Bulk, Melt-Textured HTS

The properties of discontinuous aligned pinning centers (PCs) created by high-energy heavy-ions are compared for bulk melt-textured and coated conductor HTS. Properties of PCs, which increase J{sub c} (pinning potential and entanglement), and negative properties which decrease J{sub c} (e.g., decreased T{sub c} and percolation paths) are evaluated. Mechanisms are proposed to explain the very large increases in J{sub c} resulting from multiple-in-line-damage (MILD) compared to continuous columnar pinning centers (CCPC). In particular, a mechanism which results in fluxoid entanglement, even for parallel (unsplayed) PCs, is discussed. The same mechanism is found to also account for restoration of much of the pinning potential expected to be lost due to the gaps in MILD PCs. It also accounts for the fact that at high fluence, J{sub c} increases as fluence is increased, instead of decreasing as expected. The very low self-field in coated conductor permits separation of the negative and positive effects of PCs. It is found that parameters developed to quantify the negative effects in bulk melt-textured YBCO, by 63 GeV U{sup 238} ions, successfully describe damage to 2.1 {micro}m thick coated conductor by 1 GeV Ru{sup 44} ions. Coated conductor at 77 K and self-field is generally known to have J{sub c} about 100 times that of melt-textured YBCO. However, at 77 K and applied field of 1 T, when both forms of HTS are processed with comparable numbers of near-optimum MILD PCs, the difference in J{sub c} is reduced to a factor of 1.3-2. Whereas J{sub c} for melt-textured YBCO increased sharply, by a factor of up to 16.8 for high-fluence MILD PCs, J{sub c} in coated conductor increased by a smaller factor of 2.5-3.0. Nevertheless, 2.1 {micro}m thick coated conductor, with near-optimum MILD PCs, exhibits J{sub c} = 543 kA/cm{sup 2} at 77 K and applied field of 1.0 T, and I{sub c} = 114 A/cm-width of conductor. This is the highest value we find in the literature. The phenomenology developed indicates that for optimum MILD PCs in coated conductor, J{sub c} {approx} 700 {+-} 70 kA/cm{sup 2} should be achievable at 77 K, 1.0 T.

74 ATOMIC AND MOLECULAR PHYSICS↗

SPOUTED BED DESIGN CONSIDERATIONS FOR COATED NUCLEAR FUEL PARTICLES

High Temperature Gas Cooled Reactors (HTGRs) are fueled with tristructural isotropic (TRISO) coated nuclear fuel particles embedded in a carbon-graphite fuel body. TRISO coatings consist of four layers of pyrolytic carbon and silicon carbide that are deposited on uranium ceramic fuel kernels (350µm – 500µm diameters) in a concatenated series of batch depositions. Each layer has dedicated functions such that the finished fuel particle has its own integral containment to minimize and control the release of fission products into the fuel body and reactor core. The TRISO coatings are the primary containment structure in the HTGR reactor and must have very high uniformity and integrity. To ensure high quality TRISO coatings, the four layers are deposited by chemical vapor deposition (CVD) using high purity precursors and are applied in a concatenated succession of batch operations before the finished product is unloaded from the coating furnace. These depositions take place at temperatures ranging from 1230°C to 1550°C and use three different gas compositions, while the fuel particle diameters double, their density drops from 11.1 g/cm3 to 3.0 g/cm3, and the bed volume increases more than 8-fold. All this is accomplished without the aid of sight ports or internal instrumentation that could cause chemical contamination within the layers or mechanical damage to thin layers in the early stages of each layer deposition. The converging section of the furnace retort was specifically designed to prevent bed stagnation that would lead to unacceptably high defect fractions and facilitate bed circulation to avoid large variability in coating layer dimensions and properties. The gas injection nozzle was designed to protect precursor gases from becoming overheated prior to injection, to induce bed spouting and preclude bed stagnation in the bottom of the retort. Furthermore, the retort and injection nozzle designs minimize buildup of pyrocarbon and silicon carbide on the retort wall and manage nozzle orifice accretions. The equipment and operating methods have yielded very good reproducibility in the TRISO coated particles batches.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Adhesion, structure, and mechanical properties of Cr HiPIMS and cathodic arc deposited coatings on SiC

Chromium deposited by high-power impulse magnetron sputtering (HIPIMS) versus cathodic arc (CA) processes exhibits very different mechanical properties. Combining the two can result in a single-phase with superior performance that can be tailored for use in coating SiC for advanced nuclear fuel cladding. Coating morphology, residual stress, elemental depth profiles, and mechanical testing by scratch, pull-off adhesion, and microcantilevers are shown for HiPIMS, CA, and combined coatings. CA coatings were likely to spall and had lower adhesion strength due to tensile residual stresses but had desirable material properties. Additionally, by depositing an initial layer of Cr by HiPIMS followed by a layer of Cr by CA, a more adherent coating was achieved and some of the stress issues with CA morphology were resolved. Combined coatings withstood at least 80 MPa in pull-off adhesion tests and had maximum failure stress values of 5GPa in microcantilever tests. These results were better than either individual deposition method and point to a hybrid approach being a path forward for a more robust coating.

36 MATERIALS SCIENCE↗

Effects of amorphous silica coating on cerium oxide nanoparticles induced pulmonary responses

Recently cerium compounds have been used in a variety of consumer products, including diesel fuel additives, to increase fuel combustion efficiency and decrease diesel soot emissions. However, cerium oxide (CeO{sub 2}) nanoparticles have been detected in the exhaust, which raises a health concern. Previous studies have shown that exposure of rats to nanoscale CeO{sub 2} by intratracheal instillation (IT) induces sustained pulmonary inflammation and fibrosis. In the present study, male Sprague–Dawley rats were exposed to CeO{sub 2} or CeO{sub 2} coated with a nano layer of amorphous SiO{sub 2} (aSiO{sub 2}/CeO{sub 2}) by a single IT and sacrificed at various times post-exposure to assess potential protective effects of the aSiO{sub 2} coating. The first acellular bronchoalveolar lavage (BAL) fluid and BAL cells were collected and analyzed from all exposed animals. At the low dose (0.15 mg/kg), CeO{sub 2} but not aSiO{sub 2}/CeO{sub 2} exposure induced inflammation. However, at the higher doses, both particles induced a dose-related inflammation, cytotoxicity, inflammatory cytokines, matrix metalloproteinase (MMP)-9, and tissue inhibitor of MMP at 1 day post-exposure. Morphological analysis of lung showed an increased inflammation, surfactant and collagen fibers after CeO{sub 2} (high dose at 3.5 mg/kg) treatment at 28 days post-exposure. aSiO{sub 2} coating significantly reduced CeO{sub 2}-induced inflammatory responses in the airspace and appeared to attenuate phospholipidosis and fibrosis. Energy dispersive X-ray spectroscopy analysis showed Ce and phosphorous (P) in all particle-exposed lungs, whereas Si was only detected in aSiO{sub 2}/CeO{sub 2}-exposed lungs up to 3 days after exposure, suggesting that aSiO{sub 2} dissolved off the CeO{sub 2} core, and some of the CeO{sub 2} was transformed to CePO{sub 4} with time. These results demonstrate that aSiO{sub 2} coating reduce CeO{sub 2}-induced inflammation, phospholipidosis and fibrosis. - Highlights: • Both CeO{sub 2} and aSiO{sub 2}/CeO{sub 2} particles were detected in the respective particle-exposed lungs. • The dissolution of aSiO{sub 2} coating from CeO{sub 2} particle core with time was demonstrated in the particle-exposed lungs. • aSiO{sub 2} coating significantly protected CeO{sub 2}-induced pulmonary inflammatory responses. • aSiO{sub 2} coating showed a protective effect on CeO{sub 2}-induced lung fibrosis.

60 APPLIED LIFE SCIENCES↗

One-Pot Coating of Ceramic Powders by Exfoliated Boron Nitride Layers with a Dense CO 2 Medium and Ultrasound-Aided Mixing

The coating or doping of substrates by two-dimensional materials to impart superior functional properties (such as improved thermal conductivity, bacterial resistance, reduced friction) is receiving increased attention. Environmentally benign, rapid and scalable coating techniques are desirable for this purpose. Here, we report a novel process for coating alumina, silicon carbide and boron carbide substrates with hexagonal boron nitride (h-BN) layers. The process consists of two sequential steps. First, h-BN layers are exfoliated from bulk h-BN in supercritical carbon dioxide (scCO 2 ) using ultrasound-aided mixing. This step is followed by self-assembly (i.e., coating) of the exfoliated h-BN on the substrates in liquid CO 2 also aided by ultrasound. The liquid CO 2 state is achieved by simply lowering the pressure and temperature of the first step below the critical point of CO 2 (P c = 72.8 atm; T c = 31.1 °C). Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) micrographs clearly reveal the exfoliation of h-BN under scCO 2 conditions as well as the h-BN assembly on various substrates under liquid CO 2 conditions. X-ray diffraction patterns confirm the structural integrity of the coated h-BN layers. It was also confirmed that without a transition to the liquid CO 2 phase following exfoliation in scCO 2 , there was negligible coating of h-BN on the substrates. Researchers in the field could consider this benign process to rapidly coat or dope materials with h-BN and other 2D materials to impart improved functional properties in myriad applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Antibacterial Copper–Hydroxyapatite Composite Coatings via Electrochemical Synthesis

Antibacterial copper-hydroxyapatite (Cu-HA) composite coatings on titanium were synthesized using a novel process consisting of two consecutive electrochemical reactions. In the first stage, HA nanocrystals were grown on titanium using cathodic electrolytic synthesis. The HA-coated titanium was then used as the cathode in a second reaction stage to electrochemically reduce Cu 2+ ions in solution to metallic Cu nanoparticles. Reaction conditions were found that result in nano-scale Cu particles growing on the surface of the HA crystals. The two-stage synthesis allows facile control of copper content in the HA coatings. Antibacterial activity was measured by culturing Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) in the presence of coatings having varying copper content. The coatings displayed copper concentration-dependent antibacterial activity against both types of bacteria, likely due to the slow release of copper ions from the coatings. Lastly, the observation of antibacterial activity from a relatively low loading of copper on the bioactive HA support suggests that multifunctional implant coatings can be developed to supplement or supplant prophylactic antibiotics used in implant surgery that are responsible for creating resistant bacteria strains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Self-generated concentration and modulus gradient coating design to protect Si nano-wire electrodes during lithiation

Surface coatings as artificial solid electrolyte interphases have been actively pursued as an effective way to improve the cycle efficiency of nanostructured Si electrodes for high energy density lithium ion batteries, where the mechanical stability of the surface coatings on Si is as critical as Si itself. However, the chemical composition and mechanical property change of coating materials during the lithiation and delithiation process imposed a grand challenge to design coating/Si nanostructure as an integrated electrode system. In our work, we first developed reactive force field (ReaxFF) parameters for Li–Si–Al–O materials to simulate the lithiation process of Si-core/Al 2 O 3 -shell and Si-core/SiO 2 -shell nanostructures. With reactive dynamics simulations, we were able to simultaneously track and correlate the lithiation rate, compositional change, mechanical property evolution, stress distributions, and fracture. A new mechanics model based on these varying properties was developed to determine how to stabilize the coating with a critical size ratio. Furthermore, we discovered that the self-accelerating Li diffusion in Al 2 O 3 coating forms a well-defined Li concentration gradient, leading to an elastic modulus gradient, which effectively avoids local stress concentration and mitigates crack propagation. Finally, based on these results, we propose a modulus gradient coating, softer outside, harder inside, as the most efficient coating to protect the Si electrode surface and improve its current efficiency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improved electrochemical performance of spinel LiMn 1.5 Ni 0.5 O 4 through MgF 2 nano-coating

In this paper, a spinel LiMn 1.5 Ni 0.5 O 4 (LMNO) cathode material synthesized by a sol–gel method is modified by MgF 2 nano-coating via a wet coating strategy. The results of X-ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FESEM) and high resolution transmission electron microscopy (HRTEM) showed that the MgF 2 nano-coating layers do not physically change the bulk structure of the pristine material. Compared with the pristine compound, the MgF 2 -coated LMNO electrodes display enhanced cycling stabilities. Particularly, the 5 wt% MgF 2 -coated LMNO demonstrates the best reversibility, with a capacity retention of 89.9% after 100 cycles, much higher than that of the pristine material, 69.3%. The dQ/dV analysis and apparent Li + diffusion coefficient calculation prove that the kinetic properties are enhanced after MgF 2 surface modification, which partly explains the improved electrochemical performances. Electrochemical impedance spectroscopy (EIS) and Fourier transform infrared spectroscopy (FTIR) data confirm that the MgF 2 coating layer helps in suppressing the fast growth of the solid electrolyte interface (SEI) film in repeated cycling, which effectively stabilizes the spinel structure. Finally and additionally, differential scanning calorimetry (DSC) tests show that the MgF 2 nano-coating layer also helps in enhancing the thermal stability of the LMNO cathode.

36 MATERIALS SCIENCE↗

Thermodynamic Properties of Aggregate Coated by Different Types of Waste Plastic: Adhesion and Moisture Resistance of Asphalt-Aggregate Systems

The utilization of acidic aggregates in hot-mix asphalt (HMA) is often inevitable due to the limited supply of locally available aggregates, posing a potential threat of moisture damage to asphalt pavements. In this regard, the use of urban waste plastic to coat the low-quality aggregates is a promising way to improve the moisture resistance. This study fundamentally evaluated the compatibility between asphalt and plastic-coated aggregate by measuring surface energy, and for the first time compared the effects of different types of waste plastic including high-density polyethylene (HDPE), low-density polyethylene (LDPE), polyethylene terephthalate (PET), polyvinyl chloride (PVC), and polypropylene (PP). The plastic-coating significantly altered the chemistry of aggregate surface by increasing the nonpolar components and reducing the polar components. Such changes remarkably increased the dry adhesion energy between asphalt and aggregate and enhanced the wettability of aggregate. For the acidic aggregates, the polymeric treatment could decrease the value of wet adhesive, which indicated the debonding tendency in the presence of water was reduced. Finally, the energy ratios of the asphalt-aggregate combinations significantly increased by the surface pretreatment, which proved the effect of waste plastic coating on improving the moisture damage resistance of asphalt mixtures. By comparison, the HDPE coating was the most effective way to enhance the compatibility with asphalt, followed by PP and LDPE coatings. The PVC and PET coatings were investigated as the least effective way. In conclusion, this study cannot only contribute to the potential large-scale utilization of waste plastic but also remove the obstacles of using large quantities of acidic natural aggregate in asphalt pavements.

36 MATERIALS SCIENCE↗

Beneficial effect of CH foam coating on x-ray emission from laser-irradiated high-Z material

Laser-irradiated Au layer with CH foam coating is investigated numerically. It is found that when coated with under-critical density CH foam more thermal radiation is produced, while less radiation is produced when coated with over-critical density CH foam. The under-critical density CH foam coating, which is heated supersonically and volumetrically by lasers, hampers the expansion of high-Z plasma and helps increase the density and temperature of Au plasma in the radiation zone. It is a practical and simple way to increase the laser x-ray conversion efficiency of hohlraum by coated with low-Z foam of under-critical density. This idea is tested with an experiment in an analogous geometry. The line emission from laser-irradiated Ti layer coated with CH foam was measured, and the increment of x-ray when coated with under-critical density CH foam was found.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Anisotropic hot deformed magnets prepared from Zn-coated MRE-Fe-B ribbon powder

Milled melt-spun ribbon flake of MRE-Fe-B coated with Zn coating using a vapor transport technique was found to have significant increase in coercivity without degrading the magnetization when the Zn thickness and heat treatment were optimized. Magnetic measurements show that 0.5–1 wt. % Zn coating increases the coercivity about 1 kOe over the initial ribbon powder. After vacuum hot deformation (VHD), the VHD magnet with Zn coating of 0.5 wt. % results in a nearly 3 kOe higher coercivity than an un-coated alloy magnet. An optimized VHD magnet with 0.5 wt. % Zn coating obtains a coercivity of 11.2 kOe and (BH)max of 23.0 MGOe, respectively. SEM and TEM microstructures analysis demonstrates that the Zn coating on the surface of ribbon powder has diffused along the intergranular boundaries after the ribbon powder was annealed at 750 °C for 30 min or was hot deformed at 700–750 °C.

36 MATERIALS SCIENCE↗