Search NASA⌕ Search

SEARCH · Search NASA

Results for “DUCTILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Full-Strength Additive Manufacturing of Pure Aluminum Alloy 7075 Using Liquid Metal Jet Printing

Additive manufacturing (AM) of high-strength aluminum alloys can produce high-performance aerospace and biomedical parts with unique geometries and functions. However, many high-performance alloy systems such as AA 7075 pose challenges during AM due to thermal cycles that cause hot cracking, limiting AM to casting-friendly alloys. Stock AA 7075 alloy poses additional challenges due to the excessive growth of insoluble precipitates during casting and needs to be thermomechanically processed to obtain acceptable mechanical properties. Here, this work uses liquid metal jet printing to produce high-resolution pure AA 7075 parts at high strength (593 MPa) and ductility (10 pct), surpassing the specific strength of any type of steel. The parts are printed by depositing fine droplets on a high-temperature substrate that reduces cooling rates, preventing hot cracking. The results show that fully dense, crack-free parts can only be printed at substrate temperatures of 500 °C with a cooling rate threshold of < 2000 K/s to prevent cracking and < 500 K/s to eliminate porosity. The tensile strength, microhardness, and ductility of the parts matched or were beyond the wrought alloy specifications after heat treatment, possibly due to high solidification rates that produce finer insoluble precipitates. Our results indicate that many challenging high-performance alloy systems can now be 3D printed based on the critical thresholds for cooling rates using any AM method that can satisfy these conditions.

36 MATERIALS SCIENCE↗

Slow Strain Rate Testing for Hydrogen Embrittlement Susceptibility of Alloy 718 in Substitute Ocean Water

The hydrogen embrittlement susceptibility of near-peak-aged UNS N07718 (Alloy 718) was evaluated by performing slow strain rate tests at room temperature in air and substitute ocean water. Tests in substitute ocean water were accomplished in an environmental cell that enabled in situ cathodic charging under an applied potential of −1.1 V versus SCE. Some specimens were cathodically precharged for 4 or 16 weeks at the same potential in a 3.5 wt.% NaCl-distilled water solution at 50 °C. Unprecharged specimens tested in substitute ocean water exhibited only moderate embrittlement with plastic strain to failure decreasing by about 20% compared to unprecharged specimens tested in air. However, precharged specimens exhibited significant embrittlement with plastic strain to failure decreasing by about 70%. Test environment (air or substitute ocean water with in situ charging) and precharge time (4 or 16 weeks) had little effect on the results of the precharged specimens. Fracture surfaces of precharged specimens were typical of hydrogen embrittlement and consisted of an outer brittle ring related to the region in which hydrogen infused during precharging, a finely dimpled transition zone probably related to the region where hydrogen was drawn in by dislocation transport, and a central highly dimpled ductile region. Fracture surfaces of unprecharged specimens tested in substitute ocean water consisted of a finely dimpled outer ring and heavily dimpled central region typical of ductile fracture.

36 MATERIALS SCIENCE↗

Effect of Normalizing Temperature on Fracture Characteristic of Tensile and Impact Tested Creep Strength-Enhanced Ferritic P92 Steel

The high-temperature Cr-Mo creep strength-enhanced ferritic (CSEF) steels are mainly used in nuclear and thermal power plants. In the present investigation, a systematic study on fracture surface morphologies of tensile and impact tested specimens and mechanical properties of cast and forged (C&F) P92 steel was performed for various heat treatment conditions. The heat treatment was carried out in normalizing temperature range of 950-1150 °C and then tempered to a fixed tempering temperature of 760 °C. The effect of varying normalizing temperatures before and after tempering on microstructure evolution, tensile properties, Vicker’s hardness and Charpy toughness was studied. The normalizing temperature before and after tempering was having a noticeable effect on mechanical properties of as-received P92 steel. The fracture surface of impact and tensile tested samples was also studied for various normalizing temperatures with or without tempering. Fracture surface morphology was affected by the presence of secondary phase carbide particles. The fraction area of cleavage facets on the tensile fracture surface was found to be increased with an increase in the normalizing temperature. The fractured tensile specimens were characterized by transgranular ductile dimples, tear ridges and transgranular cleavage facets for various heat treatments. The fracture mode of impact tested samples was more complex. It showed both quasi-cleavage facets and ductile dimple tearing for various normalizing temperatures.

36 MATERIALS SCIENCE↗

Preparation and Dynamic Mechanical Properties at Elevated Temperatures of a Tungsten/Glass Composite

Experiments were conducted to prepare a borosilicate glass matrix composite containing 50 vol.% tungsten and examine its dynamic compressive behavior at elevated temperatures in the range of 450-775 °C. The results show that the homogenous microstructure of the tungsten/glass composite with relative density of ~ 97% can be obtained by hot-pressing sintering at 800 °C for 1 h under pressure of 30 MPa. Dynamic compressive testing was carried out by a separate Hopkinson pressure bar system with a synchronous device. The results show that the peak stress decreases and the composite transforms from brittle to ductile in nature with testing temperature increasing from 450 to 750 °C. The brittle–ductile transition temperature is about 500 °C. Over 775 °C, the composite loses load-bearing capacity totally because of the excessive softening of the glass phase. In addition, the deformation and failure mechanism were analyzed.

36 MATERIALS SCIENCE↗

Effect of Ni Addition to Sn0.7Cu Solder Alloy on Thermal Behavior, Microstructure, and Mechanical Properties

The addition of Ni on lead-free solder alloys Sn0.7Cu was tested in this study. A small amount of Ni was added to the solder alloys to evaluate the thermal behavior, microstructure, and mechanical properties of the composite solders after sintering and isothermal aging for 3 days and then compared with the results of the binary Sn0.7Cu solder. The results indicated that the ultimate tensile strength and yield tensile strength changed when adding 0.25 wt.% of Ni. The tested results of the differential scanning calorimeter showed that the addition of Ni (such as 0.5 and 1 wt.%) could obviously increase the solidification temperature of Sn0.7Cu alloys in the cooling process. When the Ni content was increased to 0.25 wt.% in the ternary condition, which includes the Sn0.7Cu-xNi (x = 0, 0.1, 0.25, 0.5, and 1 wt.%) solder alloys for the indentation creep test, the minimum creep rate reached the maximum; however, the trend was reversed as the Ni content was higher than this level. In addition, the microstructure of Sn-0.7Cu-xNi solder alloys was obviously different with the eutectic Sn-0.7Cu solder, such that the Ni gradually accumulated in the (Cu, Ni){sub 6}Sn{sub 5} IMCs within the Ni-containing solder alloys. Additionally, this process refined the microstructure of the Sn-0.7Cu solder. The fracture surface of the eutectic Sn-0.7Cu solder revealed ductile fracture modes; however, there was no mixed ductile–brittle fracture mode occurred when the Ni content was in the range of 0-1 wt.%.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Friction Stir Welded Q235 Low-Carbon Steel

Three-millimeter-thick Q235 steel plates were friction stir welded using a tool made of tungsten-rhenium alloy in the present study. The microstructure and mechanical properties of welded joints at various traverse speeds from 50 to 150 mm/min were analyzed. It was demonstrated that traverse speed had great impacts on microstructure and mechanical properties of the joints. Phase transformation accompanied with recrystallization occurred during FSW process which resulted in different microstructures in the WNZ, and the grain size in other zones was significantly affected by traverse speed. The highest hardness was located in the nugget zone, while the lowest hardness was found in the heat-affected zone. The transverse tensile test suggested that all the joints showed slightly lower tensile strength than that of the base material, and the tensile strength increased with increasing traverse speed. All the joints fractured in the heat-affected zone with ductile fracture mode. The impact test showed that the impact toughness decreased with the increasing traverse speed and the impact fracture surface could be divided into shear lip zone and fibrous zone which showed a typical ductile fracture.

36 MATERIALS SCIENCE↗

Comparative Evaluation of Creep-Rupture Behavior of P9 Steel Plate and Thick Section Tubeplate Forging

In the present investigation, creep-rupture behavior of P9 steel in two different product forms of 20-mm plate and 300-mm-thick tubeplate forging has been studied at 793 and 873 K. It has been found that steady-state creep rate and rupture life followed power law dependence on applied stress at low and high stress regimes for both forms of products. At high stress regime, P9 steel plate exhibited better creep strength with respect to tubeplate forging in terms of lower creep rate and higher rupture life at 793 and 873 K. On contrary, both product forms exhibited similar creep rate and rupture behavior in the low stress regime at 873 K. Difference in creep ductility has been found to be insignificant in both product forms. Irrespective of test conditions and product forms, fracture appearance remained transgranular ductile characterized by dimples. The comparative evaluation of creep-rupture properties of both product forms has also been described in terms of creep rate-rupture life relationships of Monkman–Grant type, creep damage tolerance and tertiary creep characteristics at 793 and 873 K.

36 MATERIALS SCIENCE↗

Significant Contribution to Strength Enhancement from Deformation Twins in Thermomechanically Processed Al{sub 0.1}CoCrFeNi Microstructures

Strengthening mechanisms from thermomechanical processing treatments were explored in single-phase FCC high-entropy alloy Al{sub 0.1}CoCrFeNi. Cold work offers substantial strengthening in this low stacking fault energy material owing to the resultant high work hardening rates. An enormous increase in yield strength of ~ 275% was obtained in 40% rolled material, but was accompanied by a steep drop in ductility. Recovery and recrystallization annealing treatments were investigated for improving elongation and obtaining better balance of strength–ductility combinations. Formation of novel microstructures from the different processing routes was examined. X-ray diffraction peak broadening and mechanical test results were coupled to estimate micro-strain in the different conditions and understand micro-strain’s correlation to strength. Retention of large-scale deformation twins formed during cold rolling is shown to play a key role in elevation of yield strength after heat treatments.

36 MATERIALS SCIENCE↗

Ab Initio Modeling of fcc Fe-Co-Cr-Ni High Entropy Alloys with Full Composition Range

The Fe-Co-Cr-Ni quaternary system has been studied extensively in the past decade, not only because of the superior properties achieved like high tensile ductility and fracture toughness, but also it is the foundation for the development of FeCrCoNi-based HEAs. However, most of the investigations are mainly focusing on the equiatomic and semi-equiatomic compositions. The physical properties of non-equiatomic compositions are barely explored. In the current work, the ab initio approach is adopted to predict the lattice parameter, structure stabilities, elastic properties, and enthalpy of formations of fcc Fe-Cr-Co-Ni HEA single crystals with the special quasirandom structure (SQS) method. To expand the design of Fe-Co-Cr-Ni HEAs into a full composition range, the current simulations cover all the binaries, ternaries, and the whole quaternary system. The 2-D composition-property contour diagrams are created to show the physical properties in the ternary and quaternary systems. Furthermore, our investigation shows that the fcc alloys' lattice parameter increases with the addition of Fe and Cr and decreases with Ni and Co. In addition to the enthalpy of formation at o K, the shape distortion rate is proposed to be another essential parameter to evaluate crystal stability. The results show the addition of Cr would destabilize the fcc lattice and cause symmetry breaking. Finally, the result of Pugh’s ratio shows that most of the fcc alloys show ductile behavior (P > 1.75), especially for the alloys around Fe 3 Ni, FeCo, and Fe 2 NiCo (P > 2.5). The brittle behavior (P < 1.75) is located around Fe 3 Cr and Fe 2 CoCr. Meanwhile, Cr 2 NiCo and Cr 2 FeNiCo are considered promising compositions to be tried and verified experimentally because of the higher bulk modulus and moderate shear modulus.

36 MATERIALS SCIENCE↗

Assessing Mechanical Behaviors of Additive Manufactured Alternating Layers of Inconel-718/H13 Tool Steel

An H 13 (high-strength, low-ductility) tool steel die will fail due to compressive high cycle fatigue. If the die is manufactured by direct metal deposition and layered with Inconel-718 (low-strength, high-ductility), it may impact the mechanical properties of the material. Hardness tests, micro-tensile tests, and micro-compression tests were used to analyze the mechanical properties of this additive manufactured layered metal while observing real-time morphology changes on the surface. Energy dispersive spectroscopy was also performed to determine where failure tended to occur within the Inconel-718 material. The hardness was lower than expected, as was the ultimate tensile strength, yield strength, modulus of elasticity, and strain at failure. Each tensile test failed within the Inconel-718 layer. In conclusion, a sample designed to have a single thin middle layer of Inconel-718 sandwiched by H 13 enabled the visual recording of crack initiation and propagation under a tensile load using a confocal scanning laser microscope.

36 MATERIALS SCIENCE↗

The Elevated-Temperature Strength Enhancement of a Low-Cost β Titanium Alloy Through Thermomechanically-Induced Phase Transformation

The effects of temperature and thermomechanical loading on the tensile strength and hardness were studied for a rolled, low-cost metastable β titanium alloy, Ti-13Cr-1Fe-3Al (wt.%). Tensile tests were performed at temperatures between room temperature (RT) and 410°C. The results indicated that the ultimate tensile strength (UTS) decreased with increasing temperatures up to 300°C. However, the UTS was 1400 MPa at 410°C, which was approximately 150% higher than the RT UTS. It is believed that the formation of nanoscale ω and α precipitates, identified using transmission electron microscopy, hindered the dislocation motion, which resulted in the exceptionally high UTS at 410°C. However, ductility was maintained, as the elongation-to-failure (ϵ f ) was 10% at 410°C. Dynamic mechanical analysis suggested that phase transformations occurred between 370°C-475°C. To evaluate the effect of the phase transformations on the hardness, the as-received material was heat treated at 400°C, 450°C, and 500°C for 2 h, which resulted in hardness values of approximately 340 Hv, 380 Hv, and 470 Hv, respectively. However, the greatest hardness value (500 Hv) was exhibited by the as-received material after it was tensile tested at 410°C. This suggested that both temperature and loading history affected the phase transformations. Finally, as all the samples exhibited a ductile fracture mode, this work indicates that it is possible to maintain both high strength and adequate ϵ f for Ti-13Cr-1Fe-3Al (wt.%).

36 MATERIALS SCIENCE↗

Insights into the Transformation-Induced Plasticity (TRIP) Effect in Ti-Free Grade 300 Maraging Steel Manufactured by Laser Powder Bed Fusion (LPBF)

The near-net fabrication capabilities of laser powder-bed fusion (LPBF) offer the potential to manufacture tools with complex cooling channels that can improve the production efficiency of the tools with reduced greenhouse gas emissions. High strength, toughness, and wear resistance are some of the key properties required by the tooling industries to qualify tools. While strength can be increased through appropriate heat treatments, the increase in strength comes with an associated ductility loss. Here, we show that the non-equilibrium conditions inherent to LPBF can suppress the transformation-induced plasticity effect to room temperature in a Ti-free version of grade 300 maraging steel (G300MS), which is commonly not observed at room temperature in G300MS manufactured using conventional methods. The presence of retained austenite along with Ni-rich regions was found to increase the kinetics for austenite reversion during aging, thereby enabling the transformation of austenite into ε martensite during tensile deformation at room temperature, in turn increasing the strength with minimal ductility loss.

36 MATERIALS SCIENCE↗

Microstructure and Elevated Temperature Flexure Testing of Tungsten Produced by Electron Beam Additive Manufacturing

Abstract Due to their superior high-temperature thermomechanical capabilities, sputter erosion durability, and excellent resistance to hydrogen isotopes, tungsten materials have garnered significant interest in fusion nuclear applications. However, low room-temperature ductility and complex machining strategies present significant challenges for traditional fabrication. Electron beam powder bed fusion (EB-PBF) shows promise in manufacturing pure tungsten via high thermal energy input, elevated build temperature, and a tightly controlled high-vacuum environment. This work explores the process, structure, and property relationship of pure tungsten fabricated by EB-PBF, where 99.8% relative density was achieved with reduced cracking by isolating the build substrate and optimizing the print parameter suite. Optical and electron imaging revealed that the microstructure contained equiaxed grains along the build direction, with subgrains present in all inspected grains. Flexural testing at ambient and elevated temperatures demonstrated high ductility at 900°C and flexural strength of 470 MPa at room temperature of additively manufactured tungsten.

Zhang, Haozhi↗

Deformation and Fracture Behavior of Additively Manufactured 316L Stainless Steel

Tensile deformation and fracture behavior of an additively manufactured (AM) 316L stainless steel (SS) in the as-built, stress-relieved, and solution-annealed conditions was investigated using in situ tensile testing in a scanning electron microscope with an electron back scattering diffraction (SEM–EBSD) detector. Analyses were performed to discuss the characteristic deformation and fracture process of the fine-grained AM 316L SS with and without relaxation heat treatment. The as-built 316L showed the highest strength, and both post-build heat treatments lowered the strength of the alloy. Regardless of the post-build processing, the AM 316L SS showed overall higher strength but slightly lower ductility when compared to the wrought (WT) 316L SS. Analysis of EBSD data indicated that the characteristic microstructural features from AM, such as the complex and fine grain morphology, dislocation network, pores, and silicon-rich oxides, evolved and exerted various roles during the tensile deformation and fracture processes. Further, it was obvious that the interaction of dislocation slips with oxide particles and cavities (or pores) resulted in an accelerated cracking in AM 316L SS. Overall, however, their influence on mechanical behavior was limited, as the genuinely high ductility of 316L SS could help avoid any premature or brittle fracture.

36 MATERIALS SCIENCE↗

A Review of the Influence of Processing Parameters on ODS Steels Produced via Additive Manufacturing Techniques

Abstract This paper reviews current observations regarding processing conditions for oxide dispersion-strengthened steels consolidated through additive manufacturing techniques. Variations in ODS steels observed across process parameters include changes in grain size, grain texture, oxide size, density of oxides, porosity, melt pool characteristics, and mechanical properties. These properties were then compared across techniques to understand which techniques and processing conditions lead to the highest strength, ductility, and oxide density. Current literature suggests that a mix of grain types, in the form of either morphology or phase, can significantly increase the strength of printed ODS steels. Meanwhile, the most ductile samples, regardless of consolidation technique or matrix material, were made from feedstock with oxide additions located on the powder surface. Reported grain and oxide sizes were plotted against the ratio of laser power to scan speed, volumetric energy density, and normalized enthalpy. No strong correlation between these values and microstructural features was observed. The plots that were made suggest that a larger data set, more in-depth representative equations, and more defined material properties as a function of specific feedstock used are necessary to determine a value that can be correlated to the printed ODS steel microstructure.

deJong, Matthew↗

Effect of Hot Isostatic Pressing and Powder Feedstock on Porosity, Microstructure, and Mechanical Properties of Selective Laser Melted AlSi10Mg

AlSi10Mg tensile bars were additively manufactured using the powder-bed selective laser melting process. Samples were subjected to stress relief annealing and hot isostatic pressing. Tensile samples built using fresh, stored, and reused powder feedstock were characterized for microstructure, porosity, and mechanical properties. Fresh powder exhibited the best mechanical properties and lowest porosity while stored and reused powder exhibited inferior mechanical properties and higher porosity. The microstructure of stress relieved samples was fine and exhibited (001) texture in the z-build direction. Microstructure for hot isostatic pressed samples was coarsened with fainter (001) texture. To investigate surface and interior defects, scanning electron microscopy, optical fractography, and laser scanning microscopy techniques were employed. Hot isostatic pressing eliminated internal pores and reduced the size of surface porosity associated with the selective laser melting process. Hot isostatic pressing tended to increase ductility at the expense of decreasing strength. Furthermore, scatter in ductility of hot isostatic pressed parts suggests that the presence of unclosed surface porosity facilitated fracture with crack propagation inward from the surface of the part.

36 MATERIALS SCIENCE↗

Integrative Materials Design of Three-Phase Mo-Si-B Alloys

Mo-Si-B alloys can offer higher temperature capability than Ni-base superalloys with proper balancing of the creep, ductility, and oxidation resistance through microstructure optimization. Mo-Si-B alloys are heterogeneous, containing both brittle and ductile phases and interfaces. Therefore, the phase fractions, their distributions, and their constitutive properties over the range of room temperature to maximum use temperature must be considered. This work addresses here the optimization of mechanical properties for three-phase Mo-Si-B alloys. Three modeling tools are employed: microstructure generators to re-create statistically realistic microstructures, crystal viscoplasticity constitutive equations implemented for use with finite element solvers to capture microplasticity, and reduced-order models for evaluating important mechanical properties. In particular, the effects of microstructure on elastic modulus, yield strength, fatigue resistance, and susceptibility to brittle microcracking are considered. A novel reduced-order model is introduced for the evaluation of susceptibility to microcracking at phase interfaces. It is found that the Si content of the α-Mo phase is much more significant to the alloy’s balance of mechanical properties than the α-Mo volume fraction.

36 MATERIALS SCIENCE↗

Dynamic Tensile Characterization of Thin-Sheet Brittle Metallic Materials

Refractory metals are favorable materials in applications where high strength and ductility are needed at elevated temperatures. In some cases, operating temperatures may be near the melting point of the material. However, as temperature drops, refractory metals typically undergo a significant mechanical response change - ductile-to-brittle transition. These materials may be subjected to high strain rate loading at an ambient temperature state, such as an impact or crash. Knowledge of the high rate material properties are essential for design as well as simulation of impact events. The high rate stress-strain behavior of brittle metallic materials at ambient temperature is rarely studied because of experimental challenges, particularly when failure is involved. Failure typically occurs within the non-gage section of the material, which invalidates any collected stress-strain information. Here, a method to determine a specimen geometry which will produce failures in the gage section is presented. Pure tungsten in thin-sheet form was used as a trial material to select a specimen geometry for high rate Kolsky tension bar experiments. A finite element simulation was conducted to derive a strain correction for more accurate results. The room temperature stress-strain behavior of pure tungsten at a strain rate of 24 s –1 is presented. The outcome of this experimental technique can be applied to other brittle materials for dynamic tensile characterization.

36 MATERIALS SCIENCE↗