Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUID FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Rotational and reflectional equivariant convolutional neural network for data-limited applications: Multiphase flow demonstration

This article deals with approximating steady-state particle-resolved fluid flow around a fixed particle of interest under the influence of randomly distributed stationary particles in a dispersed multiphase setup using convolutional neural network (CNN). The considered problem involves rotational symmetry about the mean velocity (streamwise) direction. Thus, this work enforces this symmetry using SE(3)-equivariant, special Euclidean group of dimension 3, CNN architecture, which is translation and three-dimensional rotation equivariant. This study mainly explores the generalization capabilities and benefits of a SE(3)-equivariant network. Accurate synthetic flow fields for Reynolds number and particle volume fraction combinations spanning over a range of [86.22, 172.96] and [0.11, 0.45], respectively, are produced with careful application of symmetry-aware data-driven approach.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2017

The boundary data immersion method for compressible flows with application to aeroacoustics

This paper introduces a virtual boundary method for compressible viscous fluid flow that is capable of accurately representing moving bodies in flow and aeroacoustic simulations. The method is the compressible extension of the boundary data immersion method (BDIM, Maertens & Weymouth (2015), ). The BDIM equations for the compressible Navier–Stokes equations are derived and the accuracy of the method for the hydrodynamic representation of solid bodies is demonstrated with challenging test cases, including a fully turbulent boundary layer flow and a supersonic instability wave. In addition we show that the compressible BDIM is able to accurately represent noise radiation from moving bodies and flow induced noise generation without any penalty in allowable time step.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2017

Verification of the Coupled Neutronics/Thermal-Hydraulics Code TANSY against the MSFR Benchmark

The MSRs is a liquid-fuel reactor in which uranium, fission products and actinides are dissolved in the molten salt. The molten salt reactors are featured by circulating fuel, low pressure and high temperature. The MSRs meets many of the future goals of nuclear technology, in particular for what concerns as improved sustainability and unique characteristics in terms of actinide burning. The fluid nature of fuel in MSRs gives extra flexibility in reactor design, fuel fabrication and recycling. But because of the application of fluid fuel, MSRs have several special characteristics compared with the traditional solid-fuel reactors. Firstly, the transport of the delayed neutron precursors by the fluid flow reduces the contribution of delayed neutrons to the chain reaction.. Secondly, the fact that the fuel is dissolved in the coolant rather than separated from the coolant by the claddings results in a much stronger coupling phenomenon between the neutronics and thermal-hydraulics. Thirdly, the shape of the fuel is determined by the container because of the characteristics of fluid, the unstructured meshes are required to model the complex geometry accurately. However most of the conventional reactor codes were developed for solid-fuel reactor and therefore not capable of taking liquid fuel flow into account. To address all these particular modeling issues of MSRs, a multi-physics code named TANSY has been developed in our laboratory. In this paper, the benchmark problem based on the MSFR design was calculated to verify the code.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Pre-Sinkhole Seismicity at the Napoleonville Salt Dome: Implications for Local Seismic Monitoring of Underground Caverns

The formation of a sinkhole at the Napoleonville salt dome located near Bayou Corne in Assumption Parish, Louisiana, was preceded by an increase in seismicity, as observed 10 km away by a continuously recording broadband seismic sensor. The seismicity rate in the days prior to the sinkhole formation contained hundreds of long-period events, some of which could be detected using a power detector (short-term to long-term energy ratio) tuned to the duration and frequency content of the seismicity. A characteristic of some of these events is a resonance near 0.4 Hz, which could be due to either an acoustic resonance within the brine-filled cavity or possibly due to unsteady fluid flow through a crack. In this work, a more exhaustive catalog was obtained using some of the events detected by the power detector as templates in a correlation detector. Furthermore, the full pre-sinkhole sequence of detections could offer lessons in remote monitoring of underground caverns.

58 GEOSCIENCES↗
DOE OSTI2020

Hydraulic characterization of a fault zone from fracture distribution

A quantitative assessment of how faults control the migration of geofluids is critical in many areas of geosciences. Here we integrated geological fieldwork, quantitative analysis of the fractures distribution and numerical modeling to build a geometrical representation of a fault zone and to characterize its hydraulic properties. Our target is a fault located in the Majella Mountain (Italy). We collected 21 scan lines across the fault profile in order to characterize its architecture. The numerical modeling of the fracture network of the damage zones and their hydraulic parameters was performed using both commercial (Move ® ) and open source software (dfnWorks and PFLOTRAN). Move ® was used to build a representative model of the fault zone using fracture spacing as a proxy, and to model the hydraulic parameters of the different fault domains. dfnWorks and PFLOTRAN were employed to infer the hydraulic parameters of the damage zones of the fault and then upscale these properties to an equivalent continuum domain, suitable for fluid flow simulations through the whole fault zone. Our findings show how even in a relatively small area it is possible to describe changes in terms of hydraulic properties of a fault zone and to build models capable to represent these variations.

58 GEOSCIENCES↗
NASA NTRS1992

A pressure correction method for the calculation of compressible chemical reacting flows

A recently developed noniterative method for the solution of the transient fluid flow equations at all speed is extended to handle chemical reacting flows. The species conservation equations are loosely coupled into the predictor/multicorrector sequence of the solution procedure. A split-operator method separates the chemical kinetics terms from the fluid-dynamical terms, as well as an implicit differencing method enhance the numerical stability. The method was applied for turbulent diffusion flame calculations and for the analyses of high pressure, axisymmetric turbulent hypersonic nozzle flows. The diffusion flame results were compared with a similar pressure method for fast chemistry integration scheme without operator-splitting. Simulations of the nozzle flow indicated that the nonideal intermolecular effects must be included in the analysis and design of high pressure hypersonic nozzle.

Chen, Z. J.↗
DOE OSTI2021

Gyrokinetic and extended-MHD simulations of a flow shear stabilized Z-pinch experiment

Axisymmetric (m = 0) gyrokinetic and extended-MHD simulations of a sheared-flow Z-pinch plasma are performed with the high-order finite volume code COGENT. The present gyrokinetic model solves the long-wavelength limit of the gyrokinetic equation for both ion and electron species coupled to the electrostatic gyro-Poisson equation for the electrostatic potential. The extended-MHD model is electromagnetic and includes the effects of the gyro-viscous pressure tensor, diamagnetic electron and ion heat fluxes, and generalized Ohm's law. Additionally, a prominent feature of this work is that the radial profiles for the plasma density and temperature are taken from the fusion Z-pinch experiment (FuZE), and the magnetic field profile is obtained as a solution of the MHD force balance equation. Such an approach allows to address realistic plasma parameters and provide insights into the current and planned experiments. In particular, it is demonstrated that the radial profiles play an important role in stabilization, as the embedded guiding center (E×B ) drift has a strong radial shear, which can contribute to the Z-pinch stabilization even in the absence of the fluid flow shear. The results of simulations for the FuZE plasma parameters show a decrease in the linear growth rate with an increase in the flow shear; however, full stabilization in the linear regime is not observed even for large (comparable to the Alfvén velocity) radial variations of the axial flow. Nonlinear stability properties of the FuZE plasmas are also studied, and it is found that profile broadening can have a pronounced stabilizing effect in the nonlinear regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Topology optimization of additively manufactured fluidic components free of internal support structures

This report integrates projection-based approaches for implementing overhang constraints with fluid topology optimization to design additively manufactured fluidic components that do not require internal support structures. Internal support structures are challenging, potentially impossible to remove in complex fluid networks, yet would degrade fluidic performance if left within the part. This presents a major challenge in coupling topology optimization with additive manufacturing in the design of fluid components. The proposed approach leverages past work in overhang constraints for solid mechanics, including projection formulations and adjoint sensitivity analysis, and considers incompressible Navier–Stokes equations for laminar fluid flow. The approach is demonstrated on 2D and 3D fluid topology optimization problems to minimize pressure drop and constrain mass flow rates in pipes and manifolds. Resulting designs are crisp, logical, satisfy performance constraints, and satisfy overhang constraints, eliminating the need for internal support structures.

42 ENGINEERING↗
NASA NTRS1994

Analyzing Flows In Rocket Nuclear Reactors

CAC is analytical prediction program to study heat-transfer and fluid-flow characteristics of circular coolant passage. Predicts, as function of time, axial and radial fluid conditions, temperatures of passage walls, rates of flow in each coolant passage, and approximate maximum material temperatures. Written in ANSI standard FORTRAN 77.

Clark, J. S.↗
DOE OSTI2025

Temperature Measurements in Hypersonic Wind Tunnels via Femtosecond Coherent Anti-Stokes Raman Scattering

A femtosecond coherent anti-Stokes Raman scattering (fs CARS) instrument is developed to perform gas-phase thermometry in cold-flow hypersonic wind tunnels. Measurements are reported for Mach 8 and 14 pure-nitrogen flows. The fs CARS instrument includes a 100 fs pump/Stokes pulse and a spectrally narrow probe pulse from a second harmonic bandwidth compressor. Important experimental considerations such as limits on the pump/Stokes pulse energy are discussed. The fs CARS focusing and collimating optics are mounted on a two-axis translation stage system to scan the measurement location during a 30 second wind tunnel run. Single-laser-shot rotational CARS spectra are recorded at the laser repetition rate of 1 kHz in the wind tunnel freestream and near simple cone models. Spectral fitting is used to determine quantitative gas temperatures. Freestream temperatures at Mach 8 and 14 spanned ranges of 40–75 and 35–50 K, respectively, depending on tunnel operating conditions. Temperature variations across the central 100 mm span of the wind tunnel were quantified. Measured temperature jumps across conical bow shocks from various models varied by less than 1% from predicted values. Hypersonic boundary layer measurements were demonstrated. In conclusion, these measurements illustrate the utility and robustness of this instrument for the study of complex fluid flow phenomena in challenging ground test facilities.

Aerodynamics↗
DOE OSTI2023

Integrated modeling of cracking during deep penetration laser welding of nickel alloys

During deep penetration laser welding of nickel alloys, interactions between composition and processing conditions can lead to the formation of defects. Inconel 740H, for example, has demonstrated a susceptibility to horizontal fusion zone cracking at locations between 70% and 80% of the weld depth during laser welding at powers above 5 kW. Coupling three-dimensional heat transfer, fluid flow, and stress modeling tools allowed that both the strain rate and stress normal to the solidification direction to be calculated. In the Inconel 740H welds, cracks formed at locations where the strain rate and stress simultaneously reached critical levels. No cracking was observed in the Inconel 690 welds, since the strain rate and stress did not simultaneously reach these critical levels.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Numerical Simulation of V-shaped Segregation in Continuous Casting Blooms Based on a Microsegregation Model

This study establishes a volume-averaged model for transport phenomena to study V-shaped segregation in continuous casting blooms with different superheating and cooling rates by coupling fluid flow, macro-scale heat transfer, and solute transport. The results demonstrate that the modified Won–Thomas model considering back diffusion in the solid phase corresponds well with the measured carbon segregation. V-shaped segregation decreases with decreasing superheating and increases slightly with decreases in the cooling rate. The results of original position statistical distribution analysis correspond well with the simulation results. This phenomenon can be exploited to improve the quality of bloom.

42 ENGINEERING↗
DOE OSTI2018

Qualification of Numerical and Semi-Analytical Modeling Codes for Thermal Design of HLW Repository - 18455

Disposal in a geological repository is a viable option for safely isolating high-level radioactive waste. Thermal processes induced by decay heat from the radioactive waste may impact the integrity of the engineered barrier system, and may lead to fluid flow and transport; and the associated migration of radionuclides. This study looks at an analysis of thermal conduction for the emplacement of high-level waste in a repository located in bedded salt. The simulations used analytical and numerical methods to study conductive heat transport in a repository. This study concentrated on heat flow in a central waste package with contributions from adjacent waste packages and drifts. Of particular importance to this work is comparison of predictions of peak temperature at the drift wall and at the waste package surface using different solution methods. Simulation results of analytical and numerical modeling methods are compared. The results show that predictions of the codes were comparable under identical initial and boundary conditions. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Review of heat transfer enhancement techniques for single phase flows

The thermal energy exchange between a flowing fluid and its confining channel is a ubiquitous process in modern society. To enhance the fluid-to-wall or wall-to-fluid heat transfer, several techniques have been developed to maximize the contact area between the fluid and the inner wall and/or disrupt the flow to enhance circulation or induce turbulence. Deployment of channels having features capable of enhancing heat transfer enables the reduction of heat exchanger size while maintaining performance. Reduction in equipment size is critical due to the ability to minimize the required volume of costly working fluids and to mitigate potential safety concerns associated with total system fluid volume. Here, a comprehensive review of single-phase heat transfer enhancement techniques is presented. The article provides a thorough comparison by analyzing the heat transfer rate, pressure drop, and other operational aspects. Single-phase heat transfer enhancement methods are divided into active and passive techniques. Active methods such as electrohydrodynamic (EHD), magnetohydrodynamics (MHD), or mechanical motion require external power to create enhancement. Passive methods such as dimples, fins, or tape inserts do not require external input and rely only on surface modification. Although active methods are more expensive and difficult to implement compared to passive techniques, it enables active control of heat transfer augmentation. Finally, this review develops and summarizes key learning data for design optimization enabled by additive manufacturing and machine learning algorithms, helping to inform these next-generation heat exchanger design methodologies for a plethora of modern applications such as electrification of vehicles, computing, and classical industries.

42 ENGINEERING↗
DOE OSTI2026

Computer simulation of reaction and transport of core-scale serpentinization of Fe-bearing olivine and evolution of geological hydrogen

We present reactive flow and transport simulations of core-scale serpentinization of forsteritic, Fe-bearing olivine under hydrothermal conditions. The model captures fluid flow, evolving porosity–permeability, and redox-controlled H 2 production in a cylindrical core over 55 days at 245 °C and 37 bar. Key processes include olivine dissolution, precipitation of serpentine and magnetite, and oxidation of Fe2+ to Fe 3+ . Here, results show strong coupling among flow velocity, alteration front propagation, and spatially heterogeneous H 2 generation. Elevated H2 concentrations align with inlet-localized magnetite precipitation, consistent with experiments. Secondary mineral formation reduces porosity and permeability, altering transport pathways. Reactive flow at the fluid–solid interface governs H 2 generation rates and distribution. Dissolved SiO2 promotes serpentine and talc formation by suppressing brucite, while bicarbonate extends reaction duration and moderates surface complexation effects.

Geologic hydrogen↗
DOE OSTI2017

Multi-Modular Coordination Control of HTR-PM600 Plant - 190

HTR-PM600 is a high temperature gas-cooled reactor plant based on the multi-modular scheme, i.e. six modular high temperature gas-cooled reactor (MHTGR) driving a common secondary loop system. Six MHTGR-based nuclear steam supplying system (NSSS) modules are tightly coupled by the secondary fluid flow network (FFN) which contains the secondary side of steam generators, feedwater system, main steam system, turbine generator system. The secondary FFN control, which focuses on the feedwater flowrates and main steam pressure, plays a central role in multi-modular coordination of HTR-PM600 plant. In this paper, a differential algebraic model of this secondary FFN is first proposed. Then, the corresponding flowrate-pressure control strategy is proposed, which takes the simple form of proportional-integral feedback laws. Numerical simulation results show both the feasibility and satisfactory transient performance of this controller. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2017

Dimensionless numbers in additive manufacturing

In this paper, the effects of many process variables and alloy properties on the structure and properties of additively manufactured parts are examined using four dimensionless numbers. The structure and properties of components made from 316 Stainless steel, Ti-6Al-4V, and Inconel 718 powders for various dimensionless heat inputs, Peclet numbers, Marangoni numbers, and Fourier numbers are studied. Temperature fields, cooling rates, solidification parameters, lack of fusion defects, and thermal strains are examined using a well-tested three-dimensional transient heat transfer and fluid flow model. The results show that lack of fusion defects in the fabricated parts can be minimized by strengthening interlayer bonding using high values of dimensionless heat input. The formation of harmful intermetallics such as laves phases in Inconel 718 can be suppressed using low heat input that results in a small molten pool, a steep temperature gradient, and a fast cooling rate. Improved interlayer bonding can be achieved at high Marangoni numbers, which results in vigorous circulation of liquid metal, larger pool dimensions, and greater depth of penetration. Finally, a high Fourier number ensures rapid cooling, low thermal distortion, and a high ratio of temperature gradient to the solidification growth rate with a greater tendency of plane front solidification.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Development of a high-resolution automatic digital (urine/electrolytes) flow volume and rate measurement system of miniature size

To aid in the quantitative analysis of man's physiological rhythms, a flowmeter to measure circadian patterns of electrolyte excretion during various environmental stresses was developed. One initial flowmeter was designed and fabricated, the sensor of which is the approximate size of a wristwatch. The detector section includes a special type of dielectric integrating type sensor which automatically controls, activates, and deactivates the flow sensor data output by determining the presence or absence of fluid flow in the system, including operation under zero-G conditions. The detector also provides qualitative data on the composition of the fluid. A compact electronic system was developed to indicate flow rate as well as total volume per release or the cumulative volume of several releases in digital/analog forms suitable for readout or telemetry. A suitable data readout instrument is also provided. Calibration and statistical analyses of the performance functions required of the flowmeter were also conducted.

Liu, F. F.↗