Search NASA⌕ Search

SEARCH · Search NASA

Results for “Finite element modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Simulating the Response of a Composite Honeycomb Energy Absorber: Full-Scale Impact Testing - Part 2

NASA has sponsored research to evaluate an externally deployable composite honeycomb designed to attenuate loads in the event of a helicopter crash. The concept, designated the Deployable Energy Absorber (DEA), is an expandable Kevlar(Registered TradeMark) honeycomb. The DEA has a flexible hinge that allows the honeycomb to be stowed collapsed until needed during an emergency. Evaluation of the DEA began with material characterization of the Kevlar(Registered TradeMark)-129 fabric/epoxy, and ended with a full-scale crash test of a retrofitted MD-500 helicopter. During each evaluation phase, finite element models of the test articles were developed and simulations were performed using the dynamic finite element code, LS-DYNA(Registered TradeMark). The paper will focus on simulations of two full-scale impact tests involving the DEA, a mass-simulator and a full-scale crash of an instrumented MD-500 helicopter. Isotropic (MAT24) and composite (MAT58) material models, which were assigned to DEA shell elements, were compared. Based on simulations results, the MAT58 model showed better agreement with test.

Fasanella, Edwin L.↗

Stress and Reliability Analysis of a Metal-Ceramic Dental Crown

Interaction of mechanical and thermal stresses with the flaws and microcracks within the ceramic region of metal-ceramic dental crowns can result in catastrophic or delayed failure of these restorations. The objective of this study was to determine the combined influence of induced functional stresses and pre-existing flaws and microcracks on the time-dependent probability of failure of a metal-ceramic molar crown. A three-dimensional finite element model of a porcelain fused-to-metal (PFM) molar crown was developed using the ANSYS finite element program. The crown consisted of a body porcelain, opaque porcelain, and a metal substrate. The model had a 300 Newton load applied perpendicular to one cusp, a load of 30ON applied at 30 degrees from the perpendicular load case, directed toward the center, and a 600 Newton vertical load. Ceramic specimens were subjected to a biaxial flexure test and the load-to-failure of each specimen was measured. The results of the finite element stress analysis and the flexure tests were incorporated in the NASA developed CARES/LIFE program to determine the Weibull and fatigue parameters and time-dependent fracture reliability of the PFM crown. CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/Or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program.

Anusavice, Kenneth J↗

R&D to Ensure a Scientific Basis for Qualification Tests and Standards (Final Report)

Project return on investment in a photovoltaic (PV) system depends increasingly on maintaining high energy yields, and the system lifetime is a major factor in levelized cost of electricity (LCOE). Thus, the rate of PV deployment and the success of these assets depends upon reliable long-term power generation. The overarching objective of this program is to improve photovoltaic (PV) module reliability via development of tests and standards. Where reliability problems or risk are discovered, we can design tests to ensure that these liabilities don't affect future generations of products. Customers can use these tests to understand which products are susceptible to certain degradation mechanisms, and manufacturers can use the tests to design unwanted characteristics out of their products. The work under this program identifies PV reliability needs, performs characterization that provides scientific understanding of targeted degradation mechanisms, and translates those data into practical and predictive test protocols and standards. Major accomplishments include: A model for polarization-type potential induced degradation (PID-p) was developed and validated against experimental data. NREL is currently leading a new edition of IEC 62804-1 for PID detection. PID-p can cause large losses in current and voltage for some module designs on cloudy days. Finite element modeling (FEM) and experiment was used to determine when cells crack in a module. It was shown that cells in landscape orientation are much more likely to crack than those on portrait orientation. Shortly thereafter, the first products with portrait-oriented cells were introduced. Studies of how to test for light and elevated temperature degradation (LeTID) culminated with the publication of IEC TS 63342. Software to predict the progression of LeTID was developed, validated, and made publicly available. Field validated tests and international standards for durability of PV module coatings abrasion, backsheets, and encapsulants were developed. Examples are IEC 62788-1-1, IEC 62788-2 ED2, IEC TS 62788-7-2, IEC 62788-7-3 ED1, IEC 63209-2. NREL led the development a high-temperature testing technical specification, and published guidelines that enable installers to determine whether higher-temperature testing is needed, simply based on location and mounting configuration. In a number of our case studies, variations in the bills of materials or workmanship have been associated with variations in reliability. These observations emphasize the importance of quality assurance to reliability. A framework for criticality (i.e. Pareto) analysis was developed and published. The framework helps us and other researchers determine what problems should be addressed for reliability research to have the biggest industry impact. NREL continues to participate actively in international standards development and stakeholder engagement activities, including organizing an annual PV Reliability Workshop. These activities are important for ensuring we address issues that are relevant and timely, and that we convey our results to those who may benefit.

14 SOLAR ENERGY↗

Micro-structural features and material properties impact on adhesive metal joints via computational modeling and machine learning

The quality of structural bonding in practical applications depends on various factors arising from materials, pre-processing conditions, and manufacturing. Understanding how these factors influence bonding performance and determining their relative importance are of significant interest. Thus, this study evaluates the effects of microstructural features and material properties on the structural strength of adhesively-bonded metal joints at the submillimeter scale, utilizing a combination of Finite Element Modeling (FEM) and Machine Learning (ML) with Gradient Boosting Regression (GBR). The microstructural features include adhesive thickness, internal voids within the adhesive, adherend-adhesive interfacial voids, void size and volume fraction, and surface roughness. The material properties include the constitutive behavior of the adhesive, as well as the adherend-adhesive interfacial strength and fracture energy. The changes in structural strength and morphologies of the bonded metal structures with respect to different microstructural features and material properties were clarified by FEM. By further leveraging ML-GBR, the sequence of importance of these factors affecting bonding performance across various scenarios was summarized. This work provides valuable insights into the development of improved structural bonding for adhesive joints in industries such as automotive , aerospace, and beyond.

36 MATERIALS SCIENCE↗

Orientation dependence of indentation behavior in Al–SiC nanolaminate composites

Al and SiC nanolaminate films were characterized in the perpendicular, inclined and parallel orientations using nanoindentation. The deformation was dominated by buckling of the layers when the layers were parallel to the indenter and by compression of the ductile Al layers when the layers were perpendicular to the indenter, while indentation in inclined orientations showed an intermediate behavior. Finite element modeling (FEM) of indentation deformation using wavy layers showed much more compliant behavior and prominent layer buckling than the idealized flat structure, highlighting the large effect these microstructural details can have on the deformation behavior.

36 MATERIALS SCIENCE↗

Crushing behaviors of unidirectional carbon fiber reinforced plastic composites under dynamic bending and axial crushing loading

The dynamic crushing characteristics of unidirectional carbon fiber reinforced plastic composites under two loading types, dynamic three-point bending and axial crushing, are investigated by experiment and finite element simulation. Hat section samples with two different layup orientations are tested at various impact velocities to investigate its effects. The experiment results show that delamination plays a critical role in dynamic bending deformation. Different layup orientations lead to similar crushing bending behaviors, but remarkable variations in delamination pattern evolutions. In contrast, layup orientation exerts more significant effects on failure modes and energy absorption in axial crushing. A finite element model with multiple layers of thick shell element and cohesive element is established, and simulations are performed for both dynamic three-point bending and axial crushing. The model can capture the crushing behaviors in the two loading types reasonably well. The damage evolution and energy absorption through various mechanisms at different loading conditions are discussed.

42 ENGINEERING↗

Probabilistic Sensitivity Analyses Incorporating Surrogate Models for the Structural Response of a Representative Inflatable Space Structure

This study concentrates on results from probabilistic analysis and numerical simulation tools to identify parameter sensitivities and assess surrogate model suitability for a novel inflatable airlock concept, specifically the Non-Axisymmetric Inflatable Pressure Structure (NAIPS) under NASA's Minimalistic Advanced Softgoods Hatch (MASH) Program. The current studies extended the demonstration of probabilistic analysis tools to identify parameter sensitivities by: incorporating nonlinear material load-strain property curves and orthotropic representation of the fabric; and exploring the use of surrogate models to facilitate rapid evaluations as new information becomes available, as well as enable optimizations. The airlock model has been simplified to focus on the end dome section. Brief overviews of the finite element model and associated surrogate models are provided along with the probabilistic sensitivity analysis approaches. Responses of interest include the sensitivities of various loads in the structural elements of the NAIPS to material properties, cord lengths, inflation pressure and friction between softgoods components. The use of surrogate models was explored to facilitate rapid sensitivity evaluations as parameter ranges change. The completion of the sensitivity studies improved understanding of the dependence of load responses to several uncertain parameters and confidence in the ability to use surrogate models to represent the finite element simulations.

Lyle, Karen H.↗

Limit Load and Buckling Analysis for Assessing Hanford Single-Shell Tank Dome Structural Integrity - 12278

The U.S. Department of Energy, Office of River Protection has commissioned a structural analysis of record for the Hanford single shell tanks to assess their structural integrity. The analysis used finite element techniques to predict the tank response to the historical thermal and operating loads. The analysis also addressed the potential tank response to a postulated design basis earthquake. The combined response to static and seismic loads was then evaluated against the design requirements of American Concrete Institute standard, ACI-349-06, for nuclear safety-related concrete structures. Further analysis was conducted to estimate the plastic limit load and the elastic-plastic buckling capacity of the tanks. The limit load and buckling analyses estimate the margin between the applied loads and the limiting load capacities of the tank structure. The potential for additional dome loads from waste retrieval equipment and the addition of large dome penetrations to accommodate retrieval equipment has generated additional interest in the limit load and buckling analyses. This paper summarizes the structural analysis methods that were used to evaluate the limit load and buckling of the single shell tanks. This paper summarizes the structural analysis methods that were used to evaluate the limit load and buckling limit states of the underground single shell tanks at the Hanford site. The limit loads were calculated using nonlinear finite element models that capture the progressive deformation and damage to the concrete as it approaches the limit load. Both uniform and concentrated loads over the tank dome were considered, and the analysis shows how adding a penetration in the center of the tank would affect the limit loads. For uniform surface loads, the penetration does not affect the limit load because concrete crushing and rebar yielding initiates first at the top of the wall, away from the penetration. For concentrated loads, crushing initiates at the center of the dome, so the penetration does reduce the concentrated limit load somewhat. However, the safety factors comparing the limit loads to the maximum allowable applied loads remain well above the required value of 3.0. The buckling analysis method accounts for the geometric imperfections, concrete creep, cracking and reinforcements, and concrete plasticity in determining the allowable buckling load limits. The method was demonstrated in this paper for the evaluation of a tank before and after a penetration is added in the dome center. Finite element buckling models were used to accurately calculate the linear critical buckling loads. The models showed that adding the penetration reduces the linear critical buckling load by only 2.5%. Bounding cases also showed that the possible range of soil support on the walls does not significantly affect the dome buckling loads. Buckling models of the full 360 deg. dome also showed that the dome is more resistant to buckling when the load is offset than when it is positioned over the center. These limit load and buckling analysis methods are being used at the Hanford site to assess the tank loads that can be safely applied during future waste retrieval activities. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Developing an experimental-computational framework to investigate the deformation mechanisms and mechanical properties of Al-8Ce-10Mg alloys at micro and macroscales

There is a promising future for the use of aluminum-cerium-magnesium alloys in a broad range of applications, including devices that operate at high temperatures. With cerium currently considered a waste product of rare earth mining validation studies of possible applications are essential to reduce the environmental waste. Here, a computational-experimental framework is developed to investigate the role both the intermetallic and matrix have on the mechanical properties of these alloys. A set of experiments, including SEM/EBSD imaging, nanoindentation, in-situ SEM tensile testing, and in-situ SEM-DIC tests are performed to characterize the microstructure and mechanical properties of these alloys. Furthermore, the elastic, plastic, and failure deformation mechanisms of the microstructure, and their correlation with the bulk scale mechanical properties are investigated. Experimental results are also used to calibrate parameters for a crystal plasticity finite element model, by performing a computational framework that minimizes the error between the computational and experimental results. This model is then utilized to investigate how the area percentage of intermetallics and the crystallographic texture control the mechanical properties of the alloy. Simulation results show that an increase in the percentage of intermetallics increase the strength but decrease the ductility of the alloy. Also, a change in material texture improves strength and reduces damage that leads to material failure. The development of the crystal plasticity model, as discussed in this work, opens opportunities for future investigations of similar aluminum-cerium-magnesium alloys.

36 MATERIALS SCIENCE↗

Stress and deformation modeling of multiple rotary combustion engine trochoid housings

This paper documents the development of the capability to produce finite element models of alternate trochoid housing configurations. The effort needed to produce these models is greatly reduced by the use of a newly developed specialized finite element preprocessor which is described. The results of static stress comparisons conducted on a Mazda trochoid housing are presented. Planned future development of this modeling capability to operational situations is also presented.

Lychuk, W. M.↗

Application of finite element approach to transonic flow problems

A variational finite element model for transonic small disturbance calculations is described. Different strategy is adopted in subsonic and supersonic regions. Blending elements are introduced between different regions. In the supersonic region, no upstream effect is allowed. If rectangular elements with linear shape functions are used, the model is similar to Murman's finite difference operators. Higher order shape functions, non-rectangular elements and discontinuous approximation of shock waves are also discussed.

Hafez, M. M.↗

Quantifying modeling uncertainty in simplified beam models for building response prediction

The use of simple models for response prediction of building structures is preferred in earthquake engineering for risk evaluations at regional scales, as they make computational studies more feasible. The primary impediment in their gainful use presently is the lack of viable methods for quantifying (and reducing upon) the modeling errors/uncertainties they bear. This study presents a Bayesian calibration method wherein the modeling error is embedded into the parameters of the model. Here, the method is specifically described for coupled shear-flexural beam models here, but it can be applied to any parametric surrogate model. The major benefit the method offers is the ability to consider the modeling uncertainty in the forward prediction of any degree-of-freedom or composite response regardless of the data used in calibration. The method is extensively verified using two synthetic examples. In the first example, the beam model is calibrated to represent a similar beam model but with enforced modeling errors. In the second example, the beam model is used to represent the detailed finite element model of a 52-story building. Both examples show the capability of the proposed solution to provide realistic uncertainty estimation around the mean prediction.

47 OTHER INSTRUMENTATION↗

UQpy: A general purpose Python package and development environment for uncertainty quantification

In this paper, we present the UQpy software toolbox, an open-source Python package for general uncertainty quantification (UQ) in mathematical and physical systems. The software serves as both a user-ready toolbox that includes many of the latest methods for UQ in computational modeling and a convenient development environment for Python programmers advancing the field of UQ. The paper presents an introduction to the software's architecture and existing capabilities, divided in the code in a set of modules centered around different UQ tasks such as sampling methods, generation of random processes and random fields, probabilistic inverse modeling, reliability analysis, surrogate modeling, and active learning. The paper also highlights the importance of the RunModel module, which is used to drive simulations in the uncertainty analyses performed in UQpy. This module conveniently allows the user to define computational models directly in Python, or to run simulations from a third-party software in serial or in parallel. To illustrate the various capabilities, two examples are tracked throughout the paper and analyzed repeatedly for various UQ tasks. The first is a Python model solving a nonlinear structural dynamics problem, used to illustrate UQpy's capabilities in sampling and forward propagation of high dimensional random vectors (stochastic processes), and probabilistic inference. The second model is a third-party Abaqus finite element model solving the thermomechanical response of a beam structure. This example is used to illustrate UQpy's capabilities in variance reduction sampling techniques, reliability analysis, surrogate modeling and active learning techniques.

97 MATHEMATICS AND COMPUTING↗

Ceramic composites: A review of toughening mechanisms and demonstration of micropillar compression for interface property extraction

We present that ceramic fiber–matrix composites (CFMCs) are exciting materials for engineering applications in extreme environments. By integrating ceramic fibers within a ceramic matrix, CFMCs allow an intrinsically brittle material to exhibit sufficient structural toughness for use in gas turbines and nuclear reactors. Chemical stability under high temperature and irradiation coupled with high specific strength make these materials unique and increasingly popular in extreme settings. This paper first offers a review of the importance and growing body of research on fiber–matrix interfaces as they relate to composite toughening mechanisms. Second, micropillar compression is explored experimentally as a high-fidelity method for extracting interface properties compared with traditional fiber push-out testing. Three significant interface properties that govern composite toughening were extracted. For a 50-nm-pyrolytic carbon interface, the following were observed: a fracture energy release rate of ~2.5 J/m 2 , an internal friction coefficient of 0.25 ± 0.04, and a debond shear strength of 266 ± 24 MPa. Lastly, this research supports micromechanical evaluations as a unique bridge between theoretical physics models for microcrack propagation and empirically driven finite element models for bulk CFMCs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

The verification and uncertainty quantification of surrogate models used for structural analysis

High fidelity modeling of complex systems can require large finite element models to capture the physics of interest. Typically these high-order models take an excessively long time to run. For important studies such as model validation and uncertainty quantification, where probabilistic measures of the response are required, a large number of simulations of the high fidelity model with different parameters are necessary. In addition, some environments, such as an extensive random vibration excitation, require a long simulation time to capture the entire event. A process that produces a highly efficient model from the original high order model is necessary to enable these analyses. These highly efficient models are referred to as surrogate models, for their purpose is to represent the main physics that is of importance, but decrease the computational burden. A critical aspect of any surrogate model is how faithfully the efficient model represents the original high-order model. This paper describes the process for verifying a surrogate model using response quantities of interest and quantifying the introduced uncertainties in the use of the surrogate model. This is done to help any analyst if they use any surrogate model; such has, Craig-Bampton Reduc tions, POD, etc.

Ross, Michael↗

Distributed system modeling of a large space antenna

A general approach for distributed parameter modeling of complex dynamical systems is described. The method consists of dividing the system in parts which can be modeled by simple partial differential equations and coupling the equations thus obtained by applying Hamilton's variational formalism to the entire system. The modeling of a large, offset-fed, wrap-rib antenna is presented to illustrate the approach. Although such models are perhaps not as precise as finite element models, they can be useful for initial physical insight and parametric design.

Hamidi, M.↗

The design, testing and analysis of aeroelastically tailored transonic flutter model wings

An investigation of both the static aeroelastic and flutter characteristics of an aft swept wing, aeroelastically tailored to washout in one design and to washin in another, has been performed using two one-fourth-scale cantilever models representing the two designs. The models have been designed using an MSC/NASTRAN finite element model to preserve the full-scale airplane washout and washin characteristics. Test results show that the effect of the skin-to-core adhesive on model stiffness must be considered in the design cycle. Flutter analyses correlate fairly well with test results. Consideration is also given to F-16 metal and washout wing flutter speeds and mass ratio effects.

Murphy, A. C.↗