Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fracturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Demonstration of thermal fracture limits of gas-cooled Nd:APG-1 and Tm:YLF slabs

High-energy short-pulse laser systems demonstrated to date have been limited to low repetition rates due to significant thermal management challenges associated with scaling these systems to high average power, including the need to understand the thermal fracture limits of laser gain media. In this paper, we demonstrate the thermal fracture limits of two high-average-power gain media in a realistic diode-pumped amplifier geometry: a 5 mm thick Nd:APG-1 slab and a 2 mm thick Tm:YLF slab, both cooled by room-temperature helium gas. Finite element analysis revealed maximum tensile stress at fracture of 25 ± 3 MPa for Nd:APG-1 and 30 ± 3 MPa for Tm:YLF. These stress levels correspond to average volumetric heat loads of 13 ± 1 W/cm 3 in Nd:APG-1 and 247 ± 12 W/cm 3 in Tm:YLF. Additional simulations show geometric scaling: thinner slabs tolerate higher heat loads before fracture, while larger pump spots reach the fracture stress at lower heat loads.

Lasers↗

Stress and Fracture of Crystalline Silicon Cells in Solar Photovoltaic Modules – A Synchrotron X-ray Microdiffraction based Investigation

Fracture of crystalline silicon (c-Si) solar cells in photovoltaic modules is a big concern to the photovoltaics (PV) industry. Cell cracks cause performance degradation and warranty issues to the manufacturers. The roots of cell fractures lie in the manufacturing and integration process of the cells and modules as they go through a series of elevated temperature and pressure processes, involving bonding of dissimilar materials, causing residual stresses. Evaluation of the exact physical mechanisms leading to these thermomechanical stresses is highly essential to quantify them and optimize the PV modules to address them. Here we present a novel synchrotron X-ray microdiffraction based techniques to characterize the stress and fracture in the crystalline silicon PV modules. We show the detailed stress state after soldering and lamination process, using the synchrotron X-ray microdiffraction experiments. We also calculate the maximum tolerable microcrack size in the c-Si cells to sustain the residual stress after lamination. We further demonstrate the effect of these residual stresses on the cell fractures using the widely accepted fracture (4-point bending) tests. These test results show that the soldering and lamination induced localized residual stresses indeed reduce the load-carrying capacity of the c-Si cells.

14 SOLAR ENERGY↗

Assessment of Lost Circulation Material Particle-Size Distribution on Fracture Sealing: A Numerical Study

Summary Lost circulation materials (LCMs) are essential to combat fluid loss while drilling and may put the whole operation at risk if a proper LCM design is not used. The focus of this research is understanding the function of LCMs in sealing fractures to reduce fluid loss. One important consideration in the success of fracture sealing is the particle-size distribution (PSD) of LCMs. Various studies have suggested different guidelines for obtaining the best size distribution of LCMs for effective fracture sealing based on limited laboratory experiments or field observations. Hence, there is a need for sophisticated numerical methods to improve the LCM design by providing some predictive capabilities. In this study, computational fluid dynamics (CFD) and discrete element methods (DEM) numerical simulations are coupled to investigate the influence of PSD of granular LCMs on fracture sealing. Dimensionless variables were introduced to compare cases with different PSDs. We validated the CFD-DEM model in reproducing specific laboratory observations of fracture-sealing experiments within the model boundary parameters. Our simulations suggested that a bimodally distributed blend would be the most effective design in comparison to other PSDs tested here.

Engineering↗

Nanoparticle-Surfactant Stabilized Strong Foam for Enhanced Oil Recovery in High-Salinity Fractured Carbonate Reservoirs

Summary Foam flooding can minimize bypassing in gasfloods in fractured reservoirs. Finding a foam formulation effective in high-salinity brine is challenging, especially with divalent cations, e.g., American Petroleum Institute (API) brine (8% NaCl with 2% CaCl2). When formulating with nanoparticles, the colloidal dispersion stability is difficult due to the dramatic reduction in zeta potential and the Debye length at high salinity. The aim of this work was to develop a strong foam in API brine at the ambient temperature, using a nonionic surfactant and ethyl cellulose nanoparticles (ECNP), for gasflooding in fractured carbonate reservoirs. ECNPs was synthesized and dispersed in API brine using a nonionic surfactant (also denoted as SF). SF and SF/ECNP foams were generated, and their stability was studied at atmospheric pressure and 950 psi. Foam mobility was measured in a sandpack at high pressure. Foam flood experiments were conducted in oil-saturated fractured carbonate cores. The nonionic surfactant proved to be a good dispersion agent for ECNP in API brine. The SF/ECNP mixture stabilized foam in API brine, even in the presence of oil. Injecting a partially miscible gas (below its minimum miscibility pressure) as an SF foam into a fractured core more than doubles the oil recovery over injection of the gas alone. The injection of the strong foam (SF/ECNP) further improves the oil recovery over that of the SF foam, indicating the synergy between ECNP and surfactant. ECNP accumulates in the foam lamella and induces larger pressure gradients in the fracture to divert more gas into the matrix for oil displacement.

Engineering↗

Autonomous Fracture Conductivity Using Expandable Proppants in Enhanced Geothermal Systems

Summary Early thermal breakthrough in enhanced geothermal systems (EGS) due to the presence of preferential flow channels is a major challenge that endangers efficient and economic heat extraction in such systems. Previous studies mainly focused on adjusting circulation rates of the working fluid, which still leaves significant amounts of untapped heat behind. Currently, there is a lack of technologies for altering flow distribution within the fracture network to achieve uniform heat sweeping in the reservoir. This work presents a novel concept for making proppants to autonomously control fracture conductivity based on the surrounding temperature. Here, proppants with negative thermal expansion coefficients have demonstrated the capability for appropriate fracture conductivity adjustment as a function of temperature to achieve uniform flow across the fracture network. Particle-particle interactions governing such functions are explicitly modeled, and then the Lattice Boltzmann methods (LBM) is used to determine the potential impact of closure stress and temperature changes on the permeability of the proposed proppant packs. Microscale analyses are further used to determine the required material properties to achieve a certain improvement in the permeability of the proppant pack. Our analyses show an enhancement in permeability and the associated fracture conductivity by half of their initial values. Field-scale analysis further confirms the effectiveness of the proposed concept as 31.4% more heat can be extracted from EGS over 50 years of production when the proposed proppants are used. Such novel proppants may effectively delay thermal breakthrough, sweep heat from larger rock volumes, and elongate the life span of the EGS project.

Engineering↗

Geomechanical Simulation of Fluid-Driven Fractures

The project supported graduate students working on experimental and numerical modeling of rock fracture, with the following objectives: (a) perform laboratory testing of fluid-saturated rock; (b) develop predictive models for simulation of fracture; and (c) establish educational frameworks for geologic sequestration issues related to rock fracture. These objectives were achieved through (i) using a novel apparatus to produce faulting in a fluid-saturated rock; (ii) modeling fracture with a boundary element method; and (iii) developing curricula for training geoengineers in experimental mechanics, numerical modeling of fracture, and poroelasticity.

58 GEOSCIENCES↗

A Nonlocal Peridynamic Plasticity Model for the Dynamic Flow and Fracture of Concrete.

A nonlocal, ordinary peridynamic constitutive model is formulated to numerically simulate the pressure-dependent flow and fracture of heterogeneous, quasi-brittle ma- terials, such as concrete. Classical mechanics and traditional computational modeling methods do not accurately model the distributed fracture observed within this family of materials. The peridynamic horizon, or range of influence, provides a characteristic length to the continuum and limits localization of fracture. Scaling laws are derived to relate the parameters of peridynamic constitutive model to the parameters of the classical Drucker-Prager plasticity model. Thermodynamic analysis of associated and non-associated plastic flow is performed. An implicit integration algorithm is formu- lated to calculate the accumulated plastic bond extension and force state. The gov- erning equations are linearized and the simulation of the quasi-static compression of a cylinder is compared to the classical theory. A dissipation-based peridynamic bond failure criteria is implemented to model fracture and the splitting of a concrete cylinder is numerically simulated. Finally, calculation of the impact and spallation of a con- crete structure is performed to assess the suitability of the material and failure models for simulating concrete during dynamic loadings. The peridynamic model is found to accurately simulate the inelastic deformation and fracture behavior of concrete during compression, splitting, and dynamically induced spall. The work expands the types of materials that can be modeled using peridynamics. A multi-scale methodology for simulating concrete to be used in conjunction with the plasticity model is presented. The work was funded by LDRD 158806.

Vogler, Tracy↗

Colloid-Facilitated Transport of Cations in an Unsaturated Fractured Soil Under Transient Conditions

Rainfall experiments were conducted using intact soil cores and an instrumented soil pedon to examine the effect of physical heterogeneity and rainfall characteristics on the mobilization of colloids, organic matter, cesium, and strontium in a fractured soil. To measure the spatial variability of infiltration of colloids and contaminants, samples were collected through a 19-port grid placed below the soil core in laboratory study and in 27 samplers at multiple depths in the soil pedon in the field study. Cesium and strontium were applied to the soil cores and the soil pedon prior to mobilization experiments. Rainwater solutions of multiple ionic strengths and organic matter concentrations were applied to the soil cores and soil pedon to mobilize in situ colloids, cesium, and strontium. The mobilization of colloids and metal cations occurred through preferential flow paths in the soil cores. Compared to steady rainfall, greater amounts of colloids were mobilized during rainfall interrupted by pauses, which indicates that the supply of colloids to be mobilized was replenished during the pauses. A maximum in the amount of mobilized colloids were mobilized during a rainfall following a pause of 2.5 d. Pauses of shorter or longer duration resulted in less colloid mobilization. Freeze-thaw cycles, a transient condition in winter, enhanced colloid mobilization and colloid-facilitated transport of cesium and strontium in the soil cores. The exchange of solutes between the soil matrix and macropores caused a hysteretic mobilization of colloids, cesium, and strontium during changes in ionic strength. Colloid-facilitated mobilization of cesium and strontium was important at low ionic strength in fractures where slow flow allowed greater exchange of flow between the fractures and the surrounding matrix. The release of cesium and strontium by cation exchange occurred at high ionic strength in fractures where there is a little exchange of pore water with the surrounding matrix. The results of the field experiment suggested that ion exchange, and not organic matter- or colloid-facilitated transport, was the dominant mechanism for mobilization of cesium and strontium through the macropores of the fractured soil.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Assessment and Validation of Mini-Compact Tension Test Specimen Geometry and Progress in Establishing Technique for Fracture Toughness Master Curves for Reactor Pressure Vessel Steels

Small specimens are playing the key role in evaluating properties of irradiated materials. The use of small specimens provides several advantages. Typically, only a small volume of material can be irradiated in a reactor at desirable conditions in terms of temperature, neutron flux, and neutron dose. A small volume of irradiated material may also allow for easier handling of specimens. Smaller specimens reduce the amount of radioactive material, minimizing personnel exposures and waste disposal. However, use of small specimens imposes a variety of challenges as well. These challenges are associated with proper accounting for size effects and transferability of small specimen data to the real structures of interest. Any fracture toughness specimen that can be made out of the broken halves of standard Charpy specimens may have exceptional utility for evaluation of reactor pressure vessels (RPVs) since it would allow one to determine and monitor directly actual fracture toughness instead of requiring indirect predictions using correlations established with impact data. The Charpy V-notch specimen is the most commonly used specimen geometry in surveillance programs. Assessment and validation of mini-CT specimen geometry has been performed on previously well characterized HSST Plate 13B, an A533B class 1 steel. It was shown that the fracture toughness transition temperature measured by these Mini-CT specimens is within the range of To values that were derived from various large fracture toughness specimens. Moreover, the scatter of the fracture toughness values measured by Mini-CT specimens perfectly follows the Weibull distribution function providing additional proof for validation of this geometry for the Master Curve evaluation of rector pressure vessel steels. Moreover, the International collaborative program has been developed to extend the assessment and validation efforts to irradiated weld metal. The program is underway and involves ORNL, CRIEPI, and EPRI.

36 MATERIALS SCIENCE↗

Transition Fracture Toughness Characterization of Eurofer 97 Steel using Pre-Cracked Miniature Multi-notch Bend Bar Specimens

In this report, we present the feasibility study of using pre-cracked miniature multi-notch bend bar specimens (M4CVN) with a dimension of 45mm (length) x 3.3mm (width) x 1.65mm (thickness) to characterize the transition fracture toughness of Eurofer97 based on the ASTM E1921 Master Curve method. From literature survey results, we did not find any obvious specimen size effects on the measured fracture toughness of unirradiated Eurofer97. Nonetheless, in order to exclude the specimen size effect on the measured fracture toughness of neutron irradiated Eurofer97, comparison of results obtained from larger size specimens with those from smaller size specimens after neutron irradiation is necessary, which is not practical and can be formidably expensive. However, limited literature results indicate that the transition fracture toughness of Eurofer97 obtained from different specimen sizes and geometries followed the similar irradiation embrittlement trend. We then described the newly designed experimental setup to be used for testing neutron irradiated Eurofer97 pre-cracked M4CVN bend bars in the hot cell. We recently used the same setup for testing neutron irradiated F82H pre-cracked miniature multi-notch bend bars with great success. Considering the similarity in materials, specimen types, and the nature of tests between Eurofer97 and F82H, we believe the newly designed experimental setup can be used successfully in fracture toughness testing of Eurofer97 pre-cracked M4CVN specimens.

36 MATERIALS SCIENCE↗

Multiscale Modeling of Deformation, Fracture and Failure of Fusion Materials and Structures Final Report

The main objective of the research performed at UCLA under grant number DE-FG02-03ER54708 was to develop a physical understanding of the underlying mechanisms that control high-temperature deformation and fracture of fusion structural materials. The key aspect is the synergistic interaction between thermo-mechanical damage phenomena (e.g. creep, fatigue, and fracture), and irradiation damage phenomena (helium and hydrogen bubbles, and irradiation-induced defects). Another thrust area of the research was on the development of constitutive equations for the mechanical behavior of irradiated structures in fusion components (mainly the First Wall and Plasma-Facing components), and in utilizing them in descriptions in large-scale Finite Element Modeling of fusion structures. A parallel experimental effort on thermo-mechanical and plasma-induced damage is designed to validate and confront the developed theoretical and computational predictions. The models have been experimentally validated through experimental tests in simulated plasma transients on specially-designed W samples. This grant started at UCLA on November 14, 2003 and has had successive continuations till November 14, 2017. Research performed under the grant was to develop a range of hierarchical models for the post-elastic deformation, fracture and failure of fusion structural materials. The developed multiscale modeling approach has been based on rigorous mathematical, physical, and computational methods at the forefront of computational materials science. At the fundamental and smallest length scale (nm-μm), we developed advanced rate theory and Monte Carlo approaches to model microstructure evolution, non-equilibrium phase transformations, and dislocation-defect interactions. Microscopic and mesoscopic models of radiation hardening, ductile-to-brittle-transition, post-elastic deformation, plastic instabilities, and fracture processes are based on Dislocation Dynamics (DD) and Grain Growth Dynamics (GGD). At the continuum level, we focused on modeling fracture and failure mechanisms for Virtual Integrated Testing (VISTA), and for understanding the limits of both materials-by-design versus structural component design through advancing the new approach of multiscale-multiphysics. The overall research has been strongly coupled with the U.S. national experimental program to ascertain and verify the range of investigated phenomena. In the following, we give a summary of research progress supported by this grant since its inception till November 14, 2017. Detailed research results are available in our publications, listed in the publications section of this report.

36 MATERIALS SCIENCE↗

Chemical-Mechanical Modeling of Subcritical-to-Critical Fracture in Geomaterials

Predicting chemical-mechanical fracture initiation and propagation in materials is a critical problem, with broad relevance to a host of geoscience applications including subsurface storage and waste disposal, geothermal energy development, and oil and gas extraction. In this project, we have developed molecular simulation and coarse- graining techniques to obtain an atomistic-level understanding of the chemical- mechanical mechanisms that control subcritical crack propagation in materials under tension and impact the fracture toughness. We have applied these techniques to the fracture of fused quartz in vacuum, in distilled water, and in two salt solutions - 1M NaC1, 1M NaOH - that form relatively acidic and basic solutions respectively. We have also established the capability to conduct double-compression double-cleavage experiments in an environmental chamber to observe material fracture in aqueous solution. Both simulations and experiments indicate that fractures propagate fastest in NaC1 solutions, slower in distilled water, and even slower in air.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrogen-Assisted Fracture of Stainless Steel

Symmetric four-point bending (S4PB) and anti-symmetric four-point bending (AS4PB) were applied to assess the effect of hydrogen on crack initiation and propagation in a stable, nitrogen-strengthened austenitic stainless steel (21Cr-6Ni-9Mn). Specimens of a high strength aluminum alloy (AA2219-T851), which has also been identified as hydrogen-compatible, were used for test method development prior to completing the stainless steel test matrix. Single edge notched bend (SEN(B)) specimens were extracted from forged 21Cr-6Ni-9Mn bar and AA2219 plate. The 21Cr-6Ni-9Mn specimens were then hydrogen charged with ~200 wt. ppm hydrogen; AA2219 specimens were not charged. Aluminum specimens were tested in S4PB to induced mode I (pure bending), and AS4PB to attain varying levels of mode I/II mixity and mode II (pure shear), where the ratio of mode I to mode II varies with the position of the crack plane relative to the load line. After test method troubleshooting and validation, hydrogen charged stainless steel specimens were then subjected to mode I and two ratios of mixed mode I/II. Mode II loading was not achieved due to high load limitations. Analyses of fracture profiles for both materials reveal a marked effect of loading mode mixity on initial crack propagation orientation, however a specific contribution of hydrogen was not readily identifiable. Fracture initiation toughness in the presence of hydrogen, J IH , was calculated following the J-integral approach; the mode I J IH calculated for stainless steel samples fractured in S4PB were consistent with published values determined from compact tension specimens. The peak loads required to initiate fracture during AS4PB far exceeded those required during S4PB. This is attributed to the increasing shear force applied to the specimens as the degree of mode mixity increases. Ultimately, understanding the fracture response of hydrogen exposed stainless steels subjected to mixed mode I/II loading is critical for designing hydrogen containment vessels or gas transfer systems (GTS).

36 MATERIALS SCIENCE↗

Material Testing of PH13-8MO H950 Steel for Xue-Wierzbicki Fracture Criterion Determination

Four tensile coupon designs of PH13-8Mo H950 steel were tested to failure using quasi-static rates to obtain data to calibrate the Xue-Wierzbicki failure model for ductile fracture. The tests recorded the force-displacement, location of the first crack, displacement to fracture, area reduction, and crack propagation path. The test method and coupon designs were adopted from Tomasz Wierzbicki’s “Calibration and evaluation of seven fracture models” report. The XueWierzbicki model predicts fracture based on accumulated equivalent plastic strain, stress triaxiality, and deviatoric state parameter. Calibrating the Xue-Wierzbicki failure model required testing four coupon designs to calculate the four free parameters in the model. The coupon designs tested a range of stress triaxialities with two axisymmetric tests, one shear test, and one plane stress test. The data obtained and presented in this report can be used to develop a Xue-Wierzbicki fracture model for PH13-8Mo H950 steel.

36 MATERIALS SCIENCE↗

Fracture Toughness of High-Cr Steels after Various Thermomechanical Treatments

This research aimed to improve the mechanical properties of high-Cr steels by developing new thermomechanical processes for application to advanced fast reactors. A simultaneous improvement of fracture toughness and strength was specifically targeted in the design of thermomechanical processing for various 9Cr and 12Cr steels. For the structural materials of fusion and fast reactors, the high-chromium steels with fine ferritic/martensitic (FM) structures are favored because of their high creep strength and excellent resistance to high-temperature radiation damage such as void swelling. After the traditional thermomechanical treatment consisting of normalizing, water quenching, and tempering, however, the high-Cr steels show limited mechanical properties at high temperatures, e.g., significant decrease of strength above ~450°C. Since the high-Cr steels are tempered at high temperatures (typically around 750°C), significant coarsening of the lath structure and carbides and annihilation of dislocations occur in the final thermomechanical treatment. It is believed that the high-temperature tempering can maximize the ductility of the FM steels, but their high-temperature strength is reduced and often with high-temperature fracture toughness. It is also likely that such a fully-tempered structure will demonstrate a lowered radiation resistance when compared to the steels with finer structures. This research was planned to explore new processing routes that can produce ultrafine microstructures and thus can improve the high-temperature mechanical properties of the high-Cr steels. In this research, three 9Cr steels and two 12Cr steels were selected and a series of new thermomechanical process treatments (TMTs) were designed and applied to the five steels to find the TMT routes that will result in increase of both strength and fracture toughness. It was demonstrated for HT-9 steels that some tailored TMTs increased or maintained the fracture toughness of the high-Cr steels while the treatments could significantly increase their strength to the level comparable to those of nanostructured ferritic alloys. This report compares the fracture toughness data of both 9Cr and 12Cr steels after various thermomechanical treatments with the reference data of similar steels. A two-step tempering route is selected for application to the high-Cr steels for reactor core structures.

36 MATERIALS SCIENCE↗

Engineered Water for Improved Oil Recovery from Fractured Reservoirs (Final Scientific/Technical Report)

The goal of this proposal is to field test the novel technology of engineered water (modifying ionic composition and/or adding surfactants or nanoparticles) injection to improve oil recovery from the carbonate matrix in fractured reservoirs. Carbonate reservoirs tend to be oil-wet/mixed-wet due to positively charged carbonate mineral surfaces and negatively charged acidic/asphaltic components in the oil. Many carbonate reservoirs are also highly fractured. Water injection does not work efficiently in fractured oil-wet reservoirs because water does not imbibe into the matrix. The water composition can be engineered with ionic modification, surfactants and nanoparticles which can change the wettability of carbonate rocks towards more water-wet conditions which can imbibe water into the matrix and push the oil into the fractures. The engineered water can also lower interfacial tension and minimize capillary forces so that gravity can push the oil up and out of the matrix. Wettability alteration also increases water relative permeability which can also improve oil recovery in non-fractured carbonate reservoirs. This technology, if successful, can be a game changer for West Texas carbonates.

02 PETROLEUM↗

Connecting In Situ Stress and Wellbore Deviation to Near-Well Fracture Complexity Using Phase-Field Simulations

The interactions among in situ stress, rock fabric, wellbore geometry, natural fractures, and other natural or man-made defects create highly complex fracture trajectories in the near-wellbore region, far more intricate than those in the far-field. These near-wellbore complexities are critical for the Utah FORGE project and Enhanced Geothermal Systems (EGS) in general. Frictional pressure loss in the near-wellbore region during stimulation can significantly influence the growth of far-field fractures, while pressure losses during circulation serve as a major source of energy dissipation. Near-wellbore fracture complexities are often observable through image logs, offering valuable insights into in situ stress characteristics. However, leveraging this information requires a high-fidelity model capable of capturing the interplay among the diverse factors influencing fracture behavior.

58 GEOSCIENCES↗

Final Report for Closing the Loop Between In Situ Stress Complexity and EGS Fracture Complexity

Characterizing in situ stress is essential in Enhanced Geothermal System (EGS) for both risk assessment and operation design. Standard stress measurement techniques such as diagnostic fracture injection tests (DFITs) require creating hydraulic fractures and apply analytical methods such as the G -function analysis to estimate the stress. These classical approaches rely on several assumptions, including but not limited to: (i) the induced fracture is planar and persistent, and (ii) the fracture plane is normal to the minimum horizontal stress. However, these assumptions may not hold in EGS environments like Utah FORGE, where thermo-hydro-mechanical (THM) coupling, wellbore deviation, and rock heterogeneity can alter the local stress condition and consequently lead to fracture complexities in both near-well and far-field regions.

15 GEOTHERMAL ENERGY↗