Search NASA⌕ Search

SEARCH · Search NASA

Results for “Power Iteration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Fiber laser cleaning of metal mirror surfaces for optical diagnostic systems of the ITER

The results of experimental studies into efficiency of removal of films with a complex composition from metal mirrors by pulsed fiber laser irradiation are presented. It is shown that the initial reflectivity of optical elements can be restored by the selection of modes of irradiation impacting the surface with the sputtered film. Effective cleaning is performed by radiation with a power density lower than 10{sup 7} W/cm{sup 2}. The removal of contaminations at such a relatively low power density occurs in a solid phase, owing to which the thermal effect on the mirror is insignificant.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A fully distributed asynchronous approach for multi-area coordinated network-constrained unit commitment

This paper discusses a consensus-based alternating direction method of multipliers (ADMM) approach to solve the multi-area coordinated network-constrained unit commitment (NCUC) problem in a distributed manner. Due to political and technical difficulties, it is neither practical nor feasible to solve the multi-area coordination problem in a centralized fashion, which requires full access to all data of individual areas. In comparison, in the proposed fully-distributed approach, local NCUC problems of individual areas can be solved independently, and only limited information is exchanged among adjacent areas for facilitating multi-area coordination. Furthermore, as traditional ADMM can only guarantee convergence for convex problems, this paper discusses several strategies to mitigate oscillations, enhance convergence performance, and derive good-enough feasible solutions, including: (i) A tie-line power flow based area coordination strategy is designed to reduce the number of global consensus variables; (ii) Different penalty parameters \r{ho} are assigned to individual consensus variables and are updated via certain rules during the iterative procedure, which would reduce the impact of initial values of \r{ho} on convergence performance; (iii) Heuristic rules are adopted to fix certain unit commitment variables for avoiding oscillations during the iterative procedure; and (iv) An asynchronous distributed strategy is studied, which solves NCUC subproblems of small areas multiple times and exchanges information with adjacent areas more frequently within one complete run of slower NCUC subproblems of large areas. Numerical cases illustrate effectiveness of the proposed asynchronous fully-distributed NCUC approach, and investigate key factors that would affect its convergence performance.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Design of interaction cavity for 170 GHz, 1 MW ITER gyrotron

In this paper the design of interaction cavity for 170 GHz, 1 MW gyrotron is presented. An in-house developed code GCOMS has been used for operating mode selection and mode competition. For 170 GHz, 1 MW gyrotron interaction cavity TE28, 7 mode excite as a operating mode at the fundamental harmonic number. The electromagnetic simulator-MAGIC, a Particle-in-Cell (PIC) code has been used for the cold cavity analysis and the beam-wave interaction. More than 1MW output power has been achieved at guiding cavity magnetic field 6.77 T. (author)

43 PARTICLE ACCELERATORS↗

Turbulent Impurity Transport

Impurity transport is an important topic for ITER as impurity density in the core has to stay below a relative concentration of 5x10{sup -5} [1] to reach ignition conditions. The reasons for that is mainly impurity radiation leading to cooling. In the edge region on the other hand site, higher impurity densities, going along with radiation energy losses are beneficial as the radiative cooling arranges for good power distribution onto the first wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High gas throughput SOLPS-ITER simulations extending the ITER database to strong detachment

Abstract SOLPS-ITER simulations performed for Q DT = 10, P SOL = 100 MW burning plasmas on ITER extend the existing database to high values of separatrix averaged neon impurity concentration (⟨ c Ne ⟩ ≈ 6%) and divertor neutral pressure (⟨ p div ⟩ > 25 Pa) in order to determine the heat flux mitigation capability of these scenarios and whether strongly detached states are accessible. In the existing database of ITER simulations, the level of detachment was limited to cases where the integral ion flux to the outer target was greater than 80% of the value at rollover, with the impurity radiation localized near the target. With the possibility of narrow heat flux channels and increased deposited power due to tile shaping, it is important to explore operation at a higher degree of detachment. Two series of simulations were explored to extend the database of SOLPS simulations. By increasing the deuterium and neon puff rates proportionally, the peak divertor energy flux ( q ⊥,max ) is decreased from 5 to 3 MW m −2 while ⟨ p div ⟩ increased from 11 to 27 Pa. By increasing only the neon puff, q ⊥, max can be reduced to <1MW m −2 while ⟨ p div ⟩ is maintained at ∼ 11 Pa. As the neon puff level is increased, the position of the impurity radiation peak is shifted towards the X-point. At the highest neon puff levels with steady-state solutions, the electron temperature is reduced below 1 eV across 50 cm of each divertor target. The new cases extend previously observed tight relationships in power and momentum loss factors to low electron temperature improving their utility for highly detached regimes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Visible spectroscopy diagnostics for tungsten source assessment in the WEST tokamak: First measurements

The present work concerns the measurements obtained with the Tungsten (W) Environment in Steady-state Tokamak (WEST) visible spectroscopy system during the first experimental campaign. This system has been developed in the framework of the WEST project that equipped the existing Tore Supra device with a tungsten divertor in order to test actively cooled tungsten Plasma Facing Components (PFC) in view of preparing for ITER operation. The goal of this diagnostic is to measure the PFC sources and the deuterium recycling with spectral, spatial, and temporal resolution adapted to the predicted power deposition profiles on the objects observed. Three kinds of PFCs are monitored: the Ion Cyclotron Resonance Heating (ICRH) antenna and Low Hybrid Current Drive (LHCD) launcher W limiters; one of the 6 W inner bumpers; and the upper and lower W divertors. Large-aperture in-vessel actively cooled optical systems (f-number ~ 3) were installed for each view and connected to optical fibres. A total of 240 optical fibers can be distributed on various detection systems including a fast response-time, multi-channel, filtered photodetector-based “Filterscope” system, developed by Oak Ridge National Laboratory (USA) as well as grating spectrometers optimized for multi-sightline analysis. The first WEST experimental campaign conducted in 2017 has been dedicated to plasma start-up development during which the visible spectroscopy system has provided crucial information related to the impurity content first and then impurity sources. The diagnostic setup for that first experimental campaign was limited to the inner bumper and outer limiters but was sufficient to demonstrate that the optical setup was in accordance with the specifications. The radiance calibration procedure allowed us to estimate fluxes from the main limiter of about 8 × 10 18 atoms/(s m 2 ) and to show a first W source radial profile along the outboard limiter.

Meyer, O.↗

The benefits of CMB delensing

The effects of gravitational lensing of the cosmic microwave background (CMB) have been measured at high significance with existing data and will be measured even more precisely in future surveys. Reversing the effects of lensing on the observed CMB temperature and polarization maps provides a variety of benefits. Delensed CMB spectra have sharper acoustic peaks and more prominent damping tails, allowing for improved inferences of cosmological parameters that impact those features. Delensing reduces B-mode power, aiding the search for primordial gravitational waves and allowing for lower variance reconstruction of lensing and other sources of secondary CMB anisotropies. Lensing-induced power spectrum covariances are reduced by delensing, simplifying analyses and improving constraints on primordial non-Gaussianities. Biases that result from incorrectly modeling nonlinear and baryonic feedback effects on the lensing power spectrum are mitigated by delensing. All of these benefits are possible without any changes to experimental or survey design. Here, we develop a self-consistent, iterative, all-orders treatment of CMB delensing on the curved sky and demonstrate the impact that delensing will have with future surveys.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Optimization Using Metamodeling in the Context of Integrated Computational Materials Engineering (ICME)

Predictive Design Technologies, LLC (PDT) proposed to employ Integrated Computational Materials Engineering (ICME) tools to help the manufacturing industry in the United States regain the competitive advantage in the global economy. ICME uses computational materials science tools within a holistic system in order to accelerate materials development, improve design optimization, and unify design and manufacturing. With the advent of accurate modeling and simulation along with significant increases in high performance computing (HPC) power, virtual design and manufacturing using ICME tools provide the means to reduce product development time and cost by alleviating costly trial-and-error physical design iterations while improving overall quality and manufacturing efficiency. To reduce the computational cost necessary for the large-scale HPC simulations and to make the methodology accessible for small and medium-sized manufacturers (SMMs), metamodels are employed. Metamodels are approximate models (functional relationships between input and output variables) that can reduce the simulation times by one to two orders of magnitude. In Phase I, PDT, partnered with Mississippi State University (MSU), demonstrated the feasibility of the proposed methodology by employing MSU?s internal state variable (ISV) plasticity-damage model with the help of metamodels to optimize the microstructure-process-property-cost for tube manufacturing processes used by Plymouth Tube Company (PTC), which involves complicated temperature and mechanical loading histories. PDT quantified the microstructure-property relationships for PTC?s SAE J525 electric resistance-welded cold drawn low carbon hydraulic 1010 steel tube manufacturing processes at seven different material states and calibrated the ISV plasticity material parameters to fit experimental tensile stress-strain curves. PDT successfully performed large scale finite element (FE) simulations in an HPC environment using the ISV plasticity model in Abaqus FE analyses of the tube forming, sizing, drawing, welding, and normalizing processes. The simulation results coupled with the manufacturing cost data were used to develop prototype metamodeling (quick response) codes which could be used to predict and optimize the microstructure-process-property-cost relationships. The developed ICME metamodeling toolkits are flexible enough to be applied to other manufacturing processes (e.g. forging, forming, casting, extrusion, rolling, stamping, and welding/joining) and metamodeling codes can run on laptop computers. Based on the work completed in Phase I, in Phase II, PDT proposes to continue to refine the ISV model by correlating and incorporating the uncertainties in the microstructure, mechanical testing, and modeling. Following the model refinement, FE analyses will be simulated and will provide even more realistic predictions as they include an appropriate window of uncertainty. Using the HPC output (FE analyses) as input, the quick-response metamodel codes will more accurately predict and optimize the microstructure-process-property-cost relationships. Furthermore, PDT propose to employ the ICME metamodeling toolkits to help develop a new tube product using entirely new high strength steel. The modeling of the high strength steel manufacturing process will replace the costly and time consuming trial-and-error methods that were used in the tubing industry previously. This simulation-based process prototyping will greatly benefit our industrial partners by opening up new market spaces due to new products with greater capabilities.

36 MATERIALS SCIENCE↗

Management of the Galileo attitude and articulation control flight software development

Management concepts are presented for software development for a new technology area, i.e., real-time autonomous, computer-based spacecraft control. Flight computer selection and sizing are done initially to maximize performance within constraints of size, power, and cost. A higher order language is chosen to enhance productivity. Because the computer is embedded in the control systems hardware and is tied to the iterative design process of the spacecraft, the management and configuration control of the software is different from more typical applications. The development process must permit early coding but accept late changes. Margin management must be a continuing process in the development. Validation and verification is a special problem because it is not feasible to test the software in the actual operating environment prior to launch.

Pace, G. D.↗

Numerical analysis of Weyl's method for integrating boundary layer equations

A fast method for accurate numerical integration of Blasius equation is proposed. It is based on the limit interchange in Weyl's fixed point method formulated as an iterated limit process. Each inner limit represents convergence to a discrete solution. It is shown that the error in a discrete solution admits asymptotic expansion in even powers of step size. An extrapolation process is set up to operate on a sequence of discrete solutions to reach the outer limit. Finally, this method is extended to related boundary layer equations.

Najfeld, I.↗

Time-Accurate Unsteady Pressure Loads Simulated for the Space Launch System at Wind Tunnel Conditions

A transonic flow field about a Space Launch System (SLS) configuration was simulated with the Fully Unstructured Three-Dimensional (FUN3D) computational fluid dynamics (CFD) code at wind tunnel conditions. Unsteady, time-accurate computations were performed using second-order Delayed Detached Eddy Simulation (DDES) for up to 1.5 physical seconds. The surface pressure time history was collected at 619 locations, 169 of which matched locations on a 2.5 percent wind tunnel model that was tested in the 11 ft. x 11 ft. test section of the NASA Ames Research Center's Unitary Plan Wind Tunnel. Comparisons between computation and experiment showed that the peak surface pressure RMS level occurs behind the forward attach hardware, and good agreement for frequency and power was obtained in this region. Computational domain, grid resolution, and time step sensitivity studies were performed. These included an investigation of pseudo-time sub-iteration convergence. Using these sensitivity studies and experimental data comparisons, a set of best practices to date have been established for FUN3D simulations for SLS launch vehicle analysis. To the author's knowledge, this is the first time DDES has been used in a systematic approach and establish simulation time needed, to analyze unsteady pressure loads on a space launch vehicle such as the NASA SLS.

Alter, Stephen J.↗

Preliminary Assessment of a Distributed Electric Propulsion System for the SUSAN Electrofan

The SUSAN Electrofan is a new hybrid electric large regional jet aircraft concept being studied by NASA that leverages advanced propulsion system technologies such as distributed electric propulsion (DEP) and boundary-layer ingestion (BLI) to reduce fuel consumption and emissions. In order to evaluate the individual benefits of these technologies toward the SUSAN Electrofan’s wing-mounted propulsion systems, three configurations are proposed. The first consists of two underwing pylon-mounted podded propulsors and serves as a baseline, while the second features an underwing pylon-mounted DEP concept with 16 ducted fans in a mail-slot nacelle. The third and final configuration mounts the mail-slot nacelle directly onto the pressure side of the wing to also take advantage of BLI. This paper presents preliminary investigations into the design and performance of the first two propulsion system configurations. This begins with an initial propulsor and mail-slot design where the aeropropulsive design space is explored, and adverse effects are addressed through iterative geometry modifications. The propulsion system configurations are then installed onto a wing–body model to account for integration effects and assess the relative aerodynamic and shaft power performance of each concept. Results indicate the potential benefits of DEP, which come from significant reductions in total drag, provided by operation at much lower propulsor fan pressure ratios.

ARMD↗

Bulk ion heating with ICRF waves in tokamaks

Heating with ICRF waves is a well-established method on present-day tokamaks and one of the heating systems foreseen for ITER. However, further work is still needed to test and optimize its performance in fusion devices with metallic high-Z plasma facing components (PFCs) in preparation of ITER and DEMO operation. This is of particular importance for the bulk ion heating capabilities of ICRF waves. Efficient bulk ion heating with the standard ITER ICRF scheme, i.e. the second harmonic heating of tritium with or without {sup 3}He minority, was demonstrated in experiments carried out in deuterium-tritium plasmas on JET and TFTR and is confirmed by ICRF modelling. This paper focuses on recent experiments with {sup 3}He minority heating for bulk ion heating on the ASDEX Upgrade (AUG) tokamak with ITER-relevant all-tungsten PFCs. An increase of 80% in the central ion temperature T{sub i} from 3 to 5.5 keV was achieved when 3 MW of ICRF power tuned to the central {sup 3}He ion cyclotron resonance was added to 4.5 MW of deuterium NBI. The radial gradient of the T{sub i} profile reached locally values up to about 50 keV/m and the normalized logarithmic ion temperature gradients R/LT{sub i} of about 20, which are unusually large for AUG plasmas. The large changes in the T{sub i} profiles were accompanied by significant changes in measured plasma toroidal rotation, plasma impurity profiles and MHD activity, which indicate concomitant changes in plasma properties with the application of ICRF waves. When the {sup 3}He concentration was increased above the optimum range for bulk ion heating, a weaker peaking of the ion temperature profile was observed, in line with theoretical expectations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Magnetostatic focal spot correction for x-ray tubes operating in strong magnetic fields using iterative optimization

Purpose: Combining x-ray fluoroscopy and MR imaging systems for guidance of interventional procedures has become more commonplace. By designing an x-ray tube that is immune to the magnetic fields outside of the MR bore, the two systems can be placed in close proximity to each other. A major obstacle to robust x-ray tube design is correcting for the effects of the magnetic fields on the x-ray tube focal spot. A potential solution is to design active shielding that locally cancels the magnetic fields near the focal spot. Methods: An iterative optimization algorithm is implemented to design resistive active shielding coils that will be placed outside the x-ray tube insert. The optimization procedure attempts to minimize the power consumption of the shielding coils while satisfying magnetic field homogeneity constraints. The algorithm is composed of a linear programming step and a nonlinear programming step that are interleaved with each other. The coil results are verified using a finite element space charge simulation of the electron beam inside the x-ray tube. To alleviate heating concerns an optimized coil solution is derived that includes a neodymium permanent magnet. Any demagnetization of the permanent magnet is calculated prior to solving for the optimized coils. The temperature dynamics of the coil solutions are calculated using a lumped parameter model, which is used to estimate operation times of the coils before temperature failure. Results: For a magnetic field strength of 88 mT, the algorithm solves for coils that consume 588 A/cm{sup 2}. This specific coil geometry can operate for 15 min continuously before reaching temperature failure. By including a neodymium magnet in the design the current density drops to 337 A/cm{sup 2}, which increases the operation time to 59 min. Space charge simulations verify that the coil designs are effective, but for oblique x-ray tube geometries there is still distortion of the focal spot shape along with deflections of approximately 3 mm in the radial and circumferential directions on the anode. Conclusions: Active shielding is an attractive solution for correcting the effects of magnetic fields on the x-ray focal spot. If extremely long fluoroscopic exposure times are required, longer operation times can be achieved by including a permanent magnet with the active shielding design.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Overview of the preliminary design of the ITER plasma control system

An overview of the Preliminary Design of the ITER Plasma Control System (PCS) is described here, which focusses on the needs for 1st plasma and early plasma operation in hydrogen/helium (H/He) up to a plasma current of 15 MA with moderate auxiliary heating power in low confinement mode (L-mode). Candidate control schemes for basic magnetic control, including divertor operation and kinetic control of the electron density with gas puffing and pellet injection, were developed. Commissioning of the auxiliary heating systems is included as well as support functions for stray field topology and real-time plasma boundary reconstruction. Initial exception handling schemes for faults of essential plant systems and for disruption protection were developed. The PCS architecture was also developed to be capable of handling basic control for early commissioning and the advanced control functions that will be needed for future high performance operation. A plasma control simulator is also being developed to test and validate control schemes. To handle the complexity of the ITER PCS, a systems engineering approach has been adopted with the development of a plasma control database to keep track of all control requirements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Self-induced steady-state magnetic field in the negative ion sources with localized rf power deposition

The study is in the scope of a recent activity on modeling of SPIDER (Source for Production of Ions of Deuterium Extracted from RF plasma) which is under development regarding the neutral beam injection heating system of ITER. The regime of non-ambipolarity in the source, established before, is completed here by introducing in the model the steady state magnetic field, self-induced in the discharge due to the dc current flowing in it. Strong changes in the discharge structure are reported.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Modeling Spacecraft Power Systems Using the SPACE Code

The NASA Glenn Research Center’s Power Architecture and Analysis Branch performs spacecraft electrical power system (EPS) performance analysis using the System Power Analysis for Capability Evaluation (SPACE) model. Accurately predicting EPS performance requires a wide range of inputs, including the spacecraft’s position, attitude, solar array temperature, load demand, and data on the EPS itself. By operating as a combined analysis tool with integrated orbit mechanics, attitude, shadowing, thermal, solar array, battery, and electrical component models, SPACE provides flexibility for the analyst to examine various scenarios without a time-consuming iterative process involving separate analysis tools and groups. SPACE also achieves short run times by tailoring the complexity of the included models, providing enough fidelity to ensure accurate EPS performance predictions without being bogged down by unnecessary detail. These advantages that SPACE has over similar power system models has contributed to its successful use on a variety of human spaceflight programs for over three decades, and makes it applicable across the development cycle from early conceptual design up through on-orbit operations.

Electrical Power System↗

Plasma edge and plasma-wall interaction modelling: Lessons learned from metallic devices

Robust power exhaust schemes employing impurity seeding are needed for target operational scenarios in present day tokamak devices with metallic plasma-facing components (PFCs). For an electricity-producing fusion power plant at power density P sep /R > 15 MW/m divertor detachment is a requirement for heat load mitigation. 2D plasma edge transport codes like the SOLPS code as well as plasma-wall interaction (PWI) codes are key to disentangle relevant physical processes in power and particle exhaust. With increased quantitative credibility in such codes more realistic and physically sound estimates of the life-time expectations and performance of metallic PFCs can be accomplished for divertor conditions relevant for ITER and DEMO. An overview is given on the recent progress of plasma edge and PWI modelling activities for (carbon-free) metallic devices, that include results from JET with the ITER-like wall, ASDEX Upgrade and Alcator C-mod. It is observed that metallic devices offer an opportunity to progress the understanding of underlying plasma physics processes in the edge. The validation of models can be substantially improved by eliminating carbon from the experiment as well as from the numerical system with reduced degrees of freedom as no chemical sputtering from amorphous carbon layers and no carbon or hydro-carbon transport are present. With the absence of carbon as the primary plasma impurity and given the fact that the physics of the PWI at metallic walls is less complex it is possible to isolate the crucial plasma physics processes relevant for particle and power exhaust. Finally, for a reliable 2D dissipative plasma exhaust model these are: cross-field drifts, complete kinetic neutral physics, geometry effects (including main-chamber, divertor and sub-divertor structures), SOL transport reflecting also the non-diffusive nature of anomalous transport, as well as transport within the pedestal region in case of significant edge impurity radiation affecting pedestal pressure and hence P sep .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗