Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reaction Control System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

A Spherical Torus Nuclear Fusion Reactor Space Propulsion Vehicle Concept for Fast Interplanetary Travel

A conceptual vehicle design enabling fast outer solar system travel was produced predicated on a small aspect ratio spherical torus nuclear fusion reactor. Initial requirements were for a human mission to Saturn with a greater than 5% payload mass fraction and a one way trip time of less than one year. Analysis revealed that the vehicle could deliver a 108 mt crew habitat payload to Saturn rendezvous in 235 days, with an initial mass in low Earth orbit of 2,941 mt. Engineering conceptual design, analysis, and assessment was performed on all ma or systems including payload, central truss, nuclear reactor (including divertor and fuel injector), power conversion (including turbine, compressor, alternator, radiator, recuperator, and conditioning), magnetic nozzle, neutral beam injector, tankage, start/re-start reactor and battery, refrigeration, communications, reaction control, and in-space operations. Detailed assessment was done on reactor operations, including plasma characteristics, power balance, power utilization, and component design.

Williams, Craig H.↗

SAMPEX Spin Stabilized Mode

The Solar, Anomalous, and Magnetospheric Particle Explorer (SAMPEX), the first of the Small Explorer series of spacecraft, was launched on July 3, 1992 into an 82' inclination orbit with an apogee of 670 km and a perigee of 520 km and a mission lifetime goal of 3 years. After more than 15 years of continuous operation, the reaction wheel began to fail on August 18,2007. With a set of three magnetic torquer bars being the only remaining attitude actuator, the SAMPEX recovery team decided to deviate from its original attitude control system design and put the spacecraft into a spin stabilized mode. The necessary operations had not been used for many years, which posed a challenge. However, on September 25, 2007, the spacecraft was successfully spun up to 1.0 rpm about its pitch axis, which points at the sun. This paper describes the diagnosis of the anomaly, the analysis of flight data, the simulation of the spacecraft dynamics, and the procedures used to recover the spacecraft to spin stabilized mode.

Tsai, Dean C.↗

Plasma Activated Water Developments for Lunar and Martian Applications

Plasma activated water (PAW) could be of great use for space applications, due to the myriad of on-demand uses. The presence of any nitrogen in the gas stream, including in a simulated Martian atmospheric composition, allows for nitrates to form in water during plasma treatment. These nitrates form nitric acid and drive down the pH while also being in a readily useable form by plants. By varying the reactions and mixing in natural additives, pH values from 2.7 to 11.5 were achieved. The pH control allows for use with many different plant species. This methodology is also enabling for space-based hydroponic systems. Growth studies of Cherry Belle radishes showed comparable dry masses of edible biomass grown with Hoagland’s nutrient solution (a best-case scenario solution that is impractical for launch transportation) and the edible biomass grown with PAW. Both solutions showed substantial improvements over the deionized water that is most similar to what is available in Space systems via the water processor assembly. Additionally, the ability to produce both acidic PAW and basic PAW has benefits for sanitation as well. Preliminary studies showed a 5.8 log reduction of P. Aeruginosa when exposed to PAW mixtures, which shows the ability to remove this common biofilm.

Ryan Gott↗

Attitude Control Approach for Solar Cruiser, a Large, Deep Space Solar Sail

Solar Cruiser is a small satellite Technology Demonstration Mission (TDM) to mature solar sail propulsion technology using a solar sail larger than 1600 square meters, demonstrating performance as a propulsion system and a stable pointing platform for science observations in an artificial halo orbit sunward of the Sun-Earth Lagrange Point 1 (sub-L1). For the “sailcraft” to meet mission ob- jectives, there are several unique attitude control challenges that the Attitude De- termination and Control System (ADCS) must overcome. Large disturbance tor- ques, primarily due to sail deformations coupled with off-sun pointing angles, make it more difficult to maintain adequate controls performance and manage accumulated momentum on the control actuators. The large-amplitude, low- frequency flexible body modes of the sail, in concert with noisy sensors and ac- tuators, make it challenging to mitigate control-structure interactions and main- tain fine pointing capabilities. Stability and control performance during sail de- ployment is complicated by rapidly and widely varying inertias. The Solar Cruiser ADCS effectively addresses these challenges using a simple, traditional control system – including momentum management actuators that use bang- bang control to constrain internal accumulated momentum, a low-pass controls filter and an attitude determination Kalman Filter (KF) that blends multiple star tracker solutions, and a reaction wheel assembly (RWA) with controller gains tuned to specific configurations or inertias. Solar Cruiser’s attitude control ap- proach, and lessons learned from its development, establishes a state of the art of high value to future solar sail missions and other small spacecraft with large de- ployable structures operating in deep space.

solar sail↗

The Effects of Gravity on Combustion and Structure Formation During Synthesis of Advanced Materials

Combustion in a variety of heterogeneous systems, leading to the synthesis of advanced materials, is characterized by high temperatures (2000-3500 K) and heating rates (up to 10(exp 6) K/s) at and ahead of the reaction front. These high temperatures generate liquids and gases which are subject to gravity-driven flow. The removal of such gravitational effects is likely to provide increased control of the reaction front, with a consequent improvement in control of the microstructure of the synthesized products. Thus, microgravity experiments can lead to major advances in the understanding of fundamental aspects of combustion and structure formation under the extreme conditions of the combustion synthesis wave. In addition, the specific features of microgravity environment allow one to produce unique materials, which cannot be obtained under terrestrial conditions. The general goals of the current research are: 1) to improve the understanding of fundamental phenomena taking place during combustion of heterogeneous systems, 2) to use low-gravity experiments for insight into the physics and chemistry of materials synthesis processes, and 3) based on the obtained knowledge, to optimize processing conditions for synthesis of advanced materials with desired microstructures and properties. This research follows logically from the results of investigations we have conducted in the framework of our previous grant on gravity influence on combustion synthesis (CS) of gasless systems. Prior work, by others and by us, has clearly demonstrated that gravity plays an important role during combustion synthesis of materials. The immediate tasks for the future are to quantitatively identify the nature of observed effects, and to create accurate local kinetic models of the processes, which can lead to a control of the microstructure and properties of the synthesized materials. In summary, this is the value of the proposed research. Based on our prior work, we focus on the fundamental aspects of combustion and structure formation under the unique condition of microgravity.

Varma, A.↗

Advanced information processing system: The Army Fault-Tolerant Architecture detailed design overview

The Army Avionics Research and Development Activity (AVRADA) is pursuing programs that would enable effective and efficient management of large amounts of situational data that occurs during tactical rotorcraft missions. The Computer Aided Low Altitude Night Helicopter Flight Program has identified automated Terrain Following/Terrain Avoidance, Nap of the Earth (TF/TA, NOE) operation as key enabling technology for advanced tactical rotorcraft to enhance mission survivability and mission effectiveness. The processing of critical information at low altitudes with short reaction times is life-critical and mission-critical necessitating an ultra-reliable/high throughput computing platform for dependable service for flight control, fusion of sensor data, route planning, near-field/far-field navigation, and obstacle avoidance operations. To address these needs the Army Fault Tolerant Architecture (AFTA) is being designed and developed. This computer system is based upon the Fault Tolerant Parallel Processor (FTPP) developed by Charles Stark Draper Labs (CSDL). AFTA is hard real-time, Byzantine, fault-tolerant parallel processor which is programmed in the ADA language. This document describes the results of the Detailed Design (Phase 2 and 3 of a 3-year project) of the AFTA development. This document contains detailed descriptions of the program objectives, the TF/TA NOE application requirements, architecture, hardware design, operating systems design, systems performance measurements and analytical models.

Harper, Richard E.↗

Silicon production in an aerosol reactor

An aerosol reactor system was developed in which large particles of silicon can be grown by silane pyrolysis. To grow particles to sizes larger than one micron, vapor deposition must be used to grow a relatively small number of seed particles. Suppression of nucleation is achieved by limiting the rate of gas phase chemical reactions such that the condensible products of the gas phase chemical reactions diffuse to the surface of the seed particles as rapidly as they are produced. This prevents high degrees of supersaturation and runaway nucleation during the growth process. Particles on the order of 10 microns were grown repeatedly with the present aersol reactor. The nucleation controlled aerosol reactor is, therefore, a suitable system for the production of powders that can readily be separated from the gas by aerodynamic means.

Wu, J. J.↗

Method for Deriving Telescope Specifications for Earth-Detecting Coronagraphs and Its Use in Prioritizing Technology Development Investments

Different potential exoplanet mission concepts require different enabling and enhancing technologies. Decisions regarding prioritizing the development of these technologies can be made using a Science-Driven Systems-Engineering framework. The white paper makes the following specific recommendations. (1) Any potential telescope/coronagraph combination should develop a wavefront stability error budget using the method described in this white paper. That error budget will inform discussions about what technology development will be needed to enable the mission. (2) Enhancing and enabling technologies requiring investment include: low noise reaction wheels or control moment gyros; micro-thruster technology; active vibration isolation; materials and design practice for making lightweight stiff structures and optical components; 200-hertz wavefront sensing and control; 500-hertz sub-picometer-precision edge sensor and position actuators; non-destructive process to quantify CTE (Coefficient of Thermal Expansion) homogeneity of 4-meter class mirrors to an uncertainty of plus or minus 1 parts per billion per degree Kelvin over a 100 by 100 sampling; laser gauge positional metrology system; and predictive active thermal control.

Space Mirror Technology↗

Influence of Load Profile on Biomechanics of the Squat and Deadlift

Long duration space travel will expose astronauts to extended periods of reduced gravity. Since gravity is not present to assist loading, astronauts will use resistive and aerobic exercise regimes for the duration of the space flight to counteract the effect reduced gravity has on the body. Astronauts will exercise on a flywheel based device on the second Orion Exploration Mission (EM2). The effect that the flywheel load profile has on biomechanics is unknown when compared to free weights or a simulated free weight profile. The purpose of this evaluation is to compare the differences in lower body kinematics and kinetics between the flywheel and free weight profile. Test subjects were instrumented with reflective markers for motion capture data collection while exercising on the Device for Aerobic and Resistive Training (DART) prototype developed by TDA Research, Inc. of Wheat Ridge, CO. Exercises performed were either the squat while wearing a harness or deadlift while grasping a T-bar, both of which interfaced with the DART through a rope cable. The DART, a motorized device controlled via software, is capable of producing different load profiles. Profiles include simulated free weights with adjustable eccentric overload capability and flywheel. Test variables included the applied device load and the load profile, both set through the DART software interface. Motion capture data was collected with a 12 camera system (Smart-DX, BTS Bioengineering, Brooklyn, NY). Bilateral ground reaction force data were collected with force plates (P6000, BTS Bioengineering). DART cable force was recorded through an internal load cell. Data was collected from a total of four test subjects. The three repetition maximum was determined for each test subject for both squat and deadlift. High, medium and low loads were determined based on this maximum. The test subject performed five repetitions of each exercise at each load and each test trial was repeated twice. Cadence was controlled during exercising. Biomechanical data were used to drive the models utilizing the OpenSim software platform. Subject specific models were scaled to match the anthropometrics of the test subjects and used to estimate the peak joint angle, joint range of motion, the peak joint moment and the joint moment impulse of the lower extremity joints and the lumbar joint.These are preliminary results because the data analysis is ongoing. There was a lot of inter-subject variability, however, in general, there was a greater peak lumbar flexion angle for the flywheel squat exercise. There was a trend towards a greater range of motion at the hip for the squat exercise with free weight. There was also a greater hip extension, lumbar extension and ankle plantar flexion impulse moment during the squat exercise with free weight. During the deadlift exercise, the peak knee flexion angle and peak knee extension moment were greater when using the free weight profile. For deadlift, the hip extension, lumbar extension and ankle plantar flexion impulse moment tended to be greater with the free weight profile. Overall, the kinematic and kinetic outcomes for the flywheel profile were either statistically the same as free weight profile in many cases, significantly reduced in a few cases, and rarely higher.

Bioengineering↗

Integrated Modeling of Advanced Opto-Mechanical Systems

The design of optical hardware for space applications is particularly challenging when developing high performance, novel systems that have no precedent. Integrated modeling and analysis of such opto-mechanical systems seeks to describe the end-to-end performance of the hardware using mission-relevant metrics. This multidisciplinary analysis might start with thermal disturbances from observation maneuvers, compute the system temperatures, compute the distorted positions and shapes of the hardware and compute the resulting optical performance. Dynamic disturbances such as reaction wheel imbalance or inertia imbalance of optical delay lines might be applied to a structural dynamic model and used in a guidance and control analysis. Mission-relevant science metrics might include wavefront quality, pointing error or imaging stability. Assembling a tool chain that can be both nimble and effective when scaled to the high fidelity models of detail design has been challenging. An integrated thermal, mechanical and optical analysis capability suitable for detail design has been developed and verified through experimental measurement. This capability was used in the design of flight-like breadboard hardware and development of a test apparatus that established both the level of performance of the hardware and the validity of the analysis. The analysis includes prediction of the thermal environment of the test chamber, detailed temperature distributions on the breadboard hardware, fine scale deformations of the optical elements, and computation of the wavefront quality using geometric optics. A battery of tests were conducted to assess the experiment data acquisition, measurement and control system and to establish the performance of the hardware design and accuracy of the integrated modeling. Thermal loads that represent operational observing maneuvers were imposed and the hardware optical performance was measured and compared to analytical predictions.

optomechanical analysis↗

Control of spin ambiguity during reorientation of an energy dissipating body

A quasi-rigid body initially spinning about its minor principal axis and experiencing energy dissipation will enter a tumbling mode and eventually reorient itself such that stable spin about its major principal axis is achieved. However, in this final state the body may be spinning in a positive or negative sense with respect to its major axis and aligned in a positive or negative sense with the inertially fixed angular momentum vector. This ambiguity can be controlled only through an active system. The associated dynamical formulations and simulations of uncontrolled reorientations are presented. Three control schemes are discussed and results offered for specific examples. These schemes include displacement of internal masses, spinning up of internal inertia, and reaction jets, all of which have demonstrated the ability to control spin ambiguity.

Kaplan, M. H.↗

Aqueous-phase source of formic acid in clouds

The coupled gas- and aqueous-phase cloud chemistry of HCOOH were examined for controlling factors in the acidity of cloud and rainwater. Attention was given to the aqueous OH/HO2 system that yields an OH species that is highly reactive with other species, notably SO2 and the formaldehyde/formic acid complex. A numerical model was developed to simulate the cloud chemistry in the remote troposphere, with considerations given to CH4-CO-NO(x)-O3-H(x)O(y) system. It was determined that aqueous phase OH radicals can produce and destroy formic acid droplets in daylight conditions, as well as control formic acid levels in rainwater. It is sugested that the same types of reactions may be involved in the control of acetic acid and other organic acids.

Chameides, W. L.↗

Design evolution of the orbiter reaction control subsystem

The challenges of space shuttle orbiter reaction control subsystem development began with selection of the propellant for the subsystem. Various concepts were evaluated before the current Earth storable, bipropellant combination was selected. Once that task was accomplished, additional challenges of designing the system to satisfy the wide range of requirements dictated by operating environments, reusability, and long life were met. Verification of system adequacy was achieved by means of a combination of analysis and test. The studies, the design efforts, and the test and analysis techniques employed in meeting the challenges are described.

Taeber, R. J.↗

Attitude Control Approach for Solar Cruiser, a Large, Deep Space Solar Sail

Solar Cruiser is a small satellite Technology Demonstration Mission (TDM) to mature solar sail propulsion technology using a solar sail larger than 1600 square meters, demonstrating performance as a propulsion system and a stable pointing platform for science observations in an artificial halo orbit sunward of the Sun-Earth Lagrange Point 1 (sub-L1). For the “sailcraft” to meet mission objectives, there are several unique attitude control challenges that the Attitude Determination and Control System (ADCS) must overcome. Large disturbance torques, primarily due to sail deformations coupled with off-sun pointing angles, make it more difficult to maintain adequate controls performance and manage accumulated momentum on the control actuators. The large-amplitude, low-frequency flexible body modes of the sail, in concert with noisy sensors and actuators, make it challenging to mitigate control-structure interactions and maintain fine pointing capabilities. Stability and control performance during sail deployment is complicated by rapidly and widely varying inertias. The Solar Cruiser ADCS effectively addresses these challenges using a simple, traditional control system – including momentum management actuators that use bang-bang control to constrain internal accumulated momentum, a low-pass controls filter and an attitude determination Kalman Filter (KF) that blends multiple star tracker solutions, and a reaction wheel assembly (RWA) with controller gains tuned to specific configurations or inertias. Solar Cruiser’s attitude control approach, and lessons learned from its development, establishes a state of the art of high value to future solar sail missions and other small spacecraft with large deployable structures operating in deep space.

solar sail↗

UAS Integration in the NAS Flight Test 6: Full Mission Results

Recent standards development efforts for the integration of Unmanned Aircraft Systems (UAS) into the National Airspace System (NAS) such as those in RTCA Inc. Special Committee 228 (SC-228) have focused on relatively large UAS transitioning to and from Class A airspace. In an effort to expand the range of vehicle classes that can access the NAS, the NASA UAS Integration in the NAS project has investigated Low Size, Weight, and Power (Low SWaP) technologies that would allow smaller UAS to detect-and-avoid (DAA) traffic. Through batch and human in the loop (HITL) simulation studies, the UAS Integration in the NAS DAA subproject have identified candidate performance standards that would contribute to enabling extended Low SWaP, UAS operations under 10,000 feet. These candidate performance standards include minimum field of regard (FOR) values for Low SWaP air surveillance sensors as well as a DAA well-clear (DWC) definition which can be applied to non-cooperative traffic to reduce the required maneuver initiation range. To test the assumptions of the project’s simulation studies and validate the candidate performance standards, a live flight research event was executed at NASA Armstrong Flight Research Center. The UAS Integration in the NAS Project Flight Test 6 Full Mission sought to characterize UAS pilot responses to traffic conflicts using a representative Low SWAP DAA system in an operational NAS environment. To achieve this, live, virtual and constructive distributed environment (LVC-DE) elements were combined to simulate a sector of Oakland center airspace and induce encounters with a live, manned aircraft. A Navmar Applied Sciences Tigershark XP was used as the UAS ownship and was integrated into the test architecture to enable it to be controlled from a Vigilant Spirit Control Station (VSCS) research ground control station. Qualified UAS pilots were recruited to act as subject pilots under test (SPUT) to control the Tigershark XP in a simulated mission while coordinating with a participating air traffic controller in simulated airspace. The intruder speed, intruder equipage and encounter geometry were varied between six scripted encounters per SPUT. Various metrics were collected including pilot reaction time from the onset of DAA alert, ATC coordination rate, probability and severity of losses of DAA well clear, and subjective ratings of system acceptability. The implications of these results on the development of standards for Low SWAP DAA systems will be discussed.

UAV↗

A Comparison of Thruster Implementation Strategies for a Deep Space Nanosatellite

Attitude control for very small spacecraft, commonly referred to as nanosatellites or CubeSats, has traditionally been carried out using reaction wheels and magnetic torquers as the primary actuators. However, as these spacecraft begin to be considered for a broader range of scientific applications, including some beyond low Earth orbit, it has become necessary to also consider thruster systems for actuation. In recent years a number of thruster designs that conform to the mass, volume, and power constraints of nanosatellites have become commercially available, including cold gas systems, pulsed plasma thrusters (PPTs), and micro-electrospray propulsion (MEP) systems. The challenge now facing the nanosatellite community is to determine which thruster solutions are appropriate for a particular application, and what the best method of control might be. This paper will compare the implementation of a cold gas system with that of an MEP or PPT system for an upcoming nanosatellite mission using a previously reported saturation-restricted control law. Results are presented for this controller both with and without a fuel-optimal thruster allocation scheme, and an assessment on incorporating these technologies in an upcoming NASA mission is offered.

Nehrenz, Matt↗

Change in blood coagulation indices as a function of the incubation period of plasma in a constant magnetic field

The influence of a constant magnetic field (CMF) with a strength of 250 and 2500 oersteds on the recalcification reaction and the tolerance of plasma to heparin was studied as a function of the exposure time of the plasma to the CMF. The maximum and reliable change in the activation of the coagulatory system of the blood was observed after a 20-hour incubation of the plasma in a CMF. As the exposure time increased, the recalcification reaction changed insigificantly; the difference between the mean arithmetic of the experiment and control values was not statistically reliable. The tolerance of the plasma to heparin as a function of the exposure time to the CMF of the plasma was considerably modified, an was statistically reliable.

Yepishina, S. G.↗

Dawn's Second and Final Extended Mission: A New Operational Campaign at Ceres

Dawn has been in orbit around Ceres since March 2015. In 2016, Dawn completed its prime mission of exploring Vesta and Ceres, and it completed an extended mission at the dwarf planet in 2017. The spacecraft has lost all reaction wheel control, making attitude control dependent on a dwindling supply of hydrazine. Nevertheless, in 2017 the project was approved for a second and final extended mission at Ceres. Starting in April 2018, Dawn used its ion propulsion system to maneuver to two new orbits. These highly elliptical orbits provided hydrazine-efficient opportunities for the acquisition of valuable new data. Now in the second of these orbits, Dawn's lowest altitude is only 9% of the lowest altitude previously in the mission, enabling significant improvements in the spatial resolution of the data. We describe Dawn operations in its second extended mission, the nature of the orbits, and the observation campaigns. We also summarize expectations for the end of the mission.

Rayman, Marc D.↗