Recent developments in large area solar cell arrays
Large area solar cell arrays for both spinning satellites and oriented planar arrays
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Large area solar cell arrays for both spinning satellites and oriented planar arrays
We report that the Intermediate Band (IB) solar cell concept is a promising idea to transcend the Shockley–Queisser limit. Using the results of first-principles calculations, we propose that colloidal nanoparticles (CNPs) are a viable and efficient platform for the implementation of the IB solar cell concept. We focused on CdSe CNPs and we showed that intragap states present in the isolated CNPs with reconstructed surfaces combine to form an IB in arrays of CNPs, which is well separated from the valence and conduction band edges. We demonstrated that optical transitions to and from the IB are active. We also showed that the IB can be electron doped in a solution, e.g., by decamethylcobaltocene, thus activating an IB-induced absorption process. Lastly, our results, together with the recent report of a nearly 10% efficient CNP solar cell, indicate that colloidal nanoparticle intermediate band solar cells are a promising platform to overcome the Shockley–Queisser limit.
A lightweight, radiation hard, high performance, ultra-thin silicon solar cell is described that incorporates light trapping and a cover glass as an integral part of the device. The manufacturing feasibility of high specific power, radiation insensitive, thin silicon solar cells was demonstrated experimentally and with a model. Ultra-thin, light trapping structures were fabricated and the light trapping demonstrated experimentally. The design uses a micro-machined, grooved back surface to increase the optical path length by a factor of 20. This silicon solar cell will be highly tolerant to radiation because the base width is less than 25 microns making it insensitive to reduction in minority carrier lifetime. Since the silicon is bonded without silicone adhesives, this solar cell will also be insensitive to UV degradation. These solar cells are designed as a form, fit, and function replacement for existing state of the art silicon solar cells with the effect of simultaneously increasing specific power, power/area, and power supply life. Using a 3-mil thick cover glass and a 0.3 g/sq cm supporting Al honeycomb, a specific power for the solar cell plus cover glass and honeycomb of 80.2 W/Kg is projected. The development of this technology can result in a revolutionary improvement in high survivability silicon solar cell products for space with the potential to displace all existing solar cell technologies for single junction space applications.
The most efficient inorganic thin film chalcogenide-based solar cells use CdTe or CuInGaSe2 (CIGS) as absorber layers, which rely on toxic (Cd) and/or scarce elements (In, Te). The desire for more sustainable solar cells has led to the development of Earth abundant and non-hazardous chalcogenide absorbers. Cu3SbS4 (famatinite) is a promising Earth abundant p-type semiconductor that has a low direct band gap (0.9–1.05 eV), is a superabsorber (absorption coefficient 104–105 cm1), and has potential in low-cost, thin-film solar cells. Although these properties make the Cu3SbS4 phase stand out as a promising material for photovoltaics, to date Cu3SbS4 solar cells have only achieved low efficiencies. In this study, we demonstrate a method for synthesizing Cu3SbS4 nanocrystals and formation of thin-films by coating nanocrystal precursors onto substrates. Optical, structural, and chemical state characterization were performed before and after thermal processing of the Cu3SbS4 films. A detailed experimental analysis of the bulk and surfaces of the Cu3SbS4 absorber films indicate that phase stability and preferential copper oxidation at the surface may limit device performance for Cu3SbS4 based solar cells. These findings may provide significant insight on how to improve Cu3SbS4 based solar cell performance by controlling processing conditions. This research was funded by the United States National Science Foundation – Scalable Nanomanufacturing program (Grant CBET-1449383). A portion of this research was performed at the Northwest Nanotechnology Infrastructure, a member of the National Nanotechnology Coordinated Infrastructure, which is supported by the National Science Foundation (Grant ECCS- 1542101). The acquisition of the OSU Titan TEM was supported by the National Science Foundation via the Major Research Instrumentation (MRI) program under Grant No. 1040588, the Murdock Charitable Trust, and the Oregon Nanoscience and Microtechnologies Institute (ONAMI). XANES spectra were obtained through an approved program user proposal at the Advanced Light Source, which is a DOE Office of Science User Facility under contract no. DE-AC02-05CH11231. The ALS approved program user proposal beam time was obtained through the chemical imaging initiative, an LDRD program at PNNL. We acknowledge Trey Diulus and Dr Igor Lyubinetsky for their assistance with the XPS experiments.
According to an aspect of an embodiment of the present disclosure, there is provided a solar cell panel and a method for manufacturing the same. The solar cell panel comprises: a solar cell for generating electric power from sunlight; a coverglass for covering the solar cell; transparent shims, which are disposed between the solar cell and the coverglass at the points where the distance between the solar cell and the coverglass needs to be controlled, and form a space between the solar cell and the coverglass; and adhesive layer, which fills the space between the solar cell and the coverglass and has the thickness the same as that of the transparent shims.
The series resistance of a solar cell is an important parameter, which must be minimized to achieve high cell efficiencies. The cell series resistance is affected by the starting material, its design, and processing. The theoretical approach proposed by Jia, et. al., is used to calculate the series resistance of indium phosphide solar cells. It is observed that the theoretical approach does not predict the series resistance correctly in all cases. The analysis was modified to include the use of effective junction ideality factor. The calculated results were compared with the available experimental results on indium phosphide solar cells processed by different techniques. It is found that the use of process dependent junction ideality factor leads to better estimation of series resistance. An accurate comprehensive series resistance model is warranted to give proper feedback for modifying the cell processing from the design state.
A three-dimensional, microscale-textured, grating-shaped organic solar cell geometry. The solar cells are fabricated on gratings to give them a three-dimensional texture that provides enhanced light absorption. Introduction of microscale texturing has a positive effect on the overall power conversion efficiency of the devices. This grating-based solar cell having a grating of pre-determined pitch and height has shown improved power-conversion efficiency over a conventional flat solar cell. The improvement in efficiency is accomplished by homogeneous coverage of the grating with uniform thickness of the active layer, which is attributed to a sufficiently high pitch and low height of the underlying gratings. Also the microscale texturing leads to suppressed reflection of incident light due to the efficient coupling of the incident light into modes that are guided in the active layer.
Wrap-around solar cell and module fabrication - costs and power output
An economical thick film solar cell contact for high volume production of low cost silicon solar array modules was investigated. All metal screenable pastes using base metals were studied. Solar cells with junction depths varying by a factor of 3.3, with and without a deposited oxide coating were used. Cells were screened and fired by a two step firing process. Adhesion and metallurgical results are unsatisfactory. No electrical information is obtained due to inadequate contact adhesion.
Solar cells may be used as receivers for laser power beaming. To understand the behavior of solar cells when illuminated by a pulsed laser, the time response of gallium arsenide and silicon solar cells to pulsed monochromatic input has been modeled using a finite element solar cell model.
Manufacturing sequence for silicon solar cells using Czochralsky crystal growing techniques in order to produce at a rate of 20 MW per year on a 24-hour per day basis is discussed. Cost analysis of the manufacturing is presented and consideration is given to the following processing decision categories of the manufacturing of an unencapsulated solar cell from a silicon wafer: (1) treatment of the optical surface; (2) formation of the junction(s); and (3) metallization of electrical collectors. The manufacturing of encapsulated solar modules from solar cells, using two glass plates, a low iron front surface, and a standard float glass back plate, is described. Totaling the three major activities of wafer making, cell manufacturing, and module fabrication, the resulting contribution to module price will be 1.945 $/watt.
Thin film GaAs solar cell fabrication and operating characteristics, describing two-cell types
Li doped Si solar cell radiation resistance to high energy electrons, noting fabrication methods and annealing behavior differences
Terrestrial applications of solar cells and design systems are considered for those applications that show the most promise for becoming practical and accepted by users within the next five years. The study includes the definition, categorization, evaluation and screening of the most attractive potential terrestrial applications for solar cells. Potential markets are initially grouped and categorized in a general sense and are weighted in priority by their business volume, present and future. From a categorized list including marine, transportation, security, communication, meteorological and others, 66 potential solar cell applications have been cataloged. A methodology was formulated to include the criteria for evaluation and screening. The evaluation process covers all parts and components of the complete system required for each application and gives consideration to all factors, such as engineering, economic, production, marketing and other factors that may have an influence on the acceptance of the system.
Abstract Interfaces play a decisive role in perovskite solar cells’ power conversion efficiency and their long‐term durability. Small‐molecule hole‐transporting materials (HTMs) have grabbed enormous attention due to their structural flexibility, material properties, and stabilities, allowing for improved operational durability in perovskite photovoltaics. This study synthesizes and investigates a new class of benzimidazole‐based small molecules, named YJS001 and YJS003 , serving as the HTMs to enable high‐efficiency mixed‐cation mixed‐halide perovskite solar cells. The benzimidazole‐based materials are dopant‐free HTMs composed of donor and acceptor building blocks that are designed to engineer the energy level alignment near the HTM/perovskite interface. Mixed‐cation mixed‐halide perovskites can be grown uniformly on both HTMs with large crystalline grains. It is discovered that the donor‐rich YJS003 ‐based solar cell exhibits a high open‐circuit voltage of 1.09 V with a champion power conversion efficiency of over 20%. Power‐dependent current–voltage characteristics of the solar cells are analyzed, from which the high performance of YJS003's excellent hole mobility and well‐aligned energy level is attributed. This work introduces a new class of benzimidazole‐based small molecules as HTMs, that paves the path for dopant free interface material development for commercialization of perovskite solar cells.
High efficiency silicon solar cells are characterized using current-voltage curves, electroluminescence imaging, impedance spectroscopy, capacitance transients, microwave photoconductive decay, and time-resolved photoluminescence imaging. The sample set is composed of cells from different manufacturers and includes an n-type silicon heterojunction (SHJ), an n-type passivated emitter rear totally diffused (PERT), and five different p-type passivated emitter rear contact (PERC) cells. Carrier lifetimes, both photoconductivity and photoluminescence, are measured co-located with the light excitation pulse and within the cell but away from the light spot. Luminescence intensity and excess carrier lifetimes correlate to cell voltage. The capacitance transient time constants correlate to the capacitance values extracted from impedance spectroscopy.
Li doped Si solar cells noting fabrication, preradiation behavior, changes with temperature, recovery and I-V characteristics after irradiation
Thermal and electrical performances of silicon solar cell designs at high solar intensities