Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solar angles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Numerical calculation of the lunar wake in a magnetohydrodynamic model.

Following previous interpretation, a model is developed which has the solar wind flowing directly into the lunar surface and the magnetic field passing unimpeded through the moon. The collapse of the plasma void behind the moon is calculated numerically using the equations of magnetohydrodynamics. The model is three-dimensional, allowing complete calculations to be made without special restrictions on the magnetic field direction. A cursory quantitative comparison with data shows agreement to be satisfactory. The calculations indicate that the rate of collapse of the void does not depend strongly on the solar wind-magnetic field angle. The penumbral decrease depends very strongly on both the solar wind-magnetic field angle and the angle of passage through the wake.

Beers, B. L.↗

The Physics of Solar Sails

The concept of using photon pressure for propulsion has been considered since Tsiolkovsky in 1921. In fact, Tsiolkovsky and Tsander wrote of 'using tremendous mirrors of very thin sheets' and 'using the pressure of sunlight to attain cosmic velocities' in 1924. The term 'solar sailing' was coined in the late 1950s and was popularized by Arthur C. Clarke in the short story Sunjammer (The Wind From the Sun) in May 1964. The National Aeronautics and Space Administration (NASA) used sailing techniques to extend the operational life of the Mariner 10 spacecraft in 1974-1975. A problem in the control system was causing Mariner 10 to go off course. By controlling the attitude of Mariner 10 and the angle of the solar power panels relative to the Sun, ground controllers were able to correct the problem without using precious fuel. Once thought to be difficult or impossible, solar sailing has come out of science fiction and into the realm of possibility. Any spacecraft using this method would need to deploy a thin sail that could be as large as many kilometers in extent. Candidate sail materials should be: 1) strong, 2) ultra-lightweight (density of a few g/sq m), 3) able to be folded or crushed until deployed, 4) subject to minimal sagging or stretching, and 5) resistant to ionizing radiation, such as galactic and solar particles (electrons and protons), x-rays, ultraviolet light, and magnetically trapped charged particles. Solar sails must be resistant to each of these types of radiation.

Hollerman, William Andrew↗

A Program of Photometric Measurements of Solar Irradiance Fluctuations from Ground-based Observations

Photometric observations of the sun have been carried out at the San Fernando Observatory since early 1985. Since 1986, observations have been obtained at two wavelengths in order to separately measure the contributions of sunspots and bright facular to solar irradiance variations. Researchers believe that the contributions of sunspots can be measured to an accuracy of about plus or minus 30 ppm. The effect of faculae is much less certain, with uncertainties in the range of plus or minus 300 ppm. The larger uncertainty for faculae reflects both the greater difficulty in measuring the facular area, due to their lower contrast compared to sunspots, and the greater uncertainty in their contrast variation with viewing angle on the solar disk. Recent results from two separate photometric telescopes will be compared with bolometric observations from the active cavity radiometer irradiance monitor (ACRIM) that was on board the Solar Max satellite.

Chapman, G. A.↗

Advanced Libya-4 radiometric and atmospheric characterization utilizing MODIS and VIIRS full-scan reflective solar band measurements

The NASA Clouds and the Earth's Radiant Energy System (CERES) project provides observed flux and cloud products to the climate science community. The CERES instruments, along with the MODIS and VIIRS imagers, are onboard the Terra, Aqua, NPP, and NOAA20 satellites. In order to produce seamless multi-platform integrated products, long-term sensor stability and inter-calibration are required. Inter-calibration between sensors within the same sun-synchronous orbit relies on Earth invariant targets because simultaneous nadir overpasses are not possible. To facilitate inter-calibration efforts, the CERES Imager and Geostationary Calibration Group (IGCG) has improved the Libya-4 target characterization. Improvements include full scan angle characterization to enable daily observations, clear-sky identification using individual scan angle dynamic spatial homogeneity thresholds, and atmospheric corrections. The water vapor correction was found to be effective across the full scan, whereas the ozone and aerosol corrections were less effective. The atmospheric-corrected normalized radiance temporal fluctuations are similar across scan angles, spectral bands, and between the MODIS and VIIRS imagers, suggesting that the fluctuations are a result of the natural variability of the Libya-4 surface reflectance. The Libya-4 surface variability is more than likely caused by changes in the prevailing winds that alter sand dune orientation and resulting shadows. The full-scan-imager atmosphere and angle corrected reflected solar band radiance trend standard errors are between 0.6% and 1.0%, and for near-nadir observations, are between 0.5% and 0.8%. The advanced characterization suggests that the Libya-4 short-term surface reflectance anomalies may need to be considered for imager stability monitoring and inter-calibration efforts.

Libya-4 Pseudo-invariant Calibration Site↗

THREE-DIMENSIONAL SOLAR WIND MODELING FROM THE SUN TO EARTH BY A SIP-CESE MHD MODEL WITH A SIX-COMPONENT GRID

The objective of this paper is to explore the application of a six-component overset grid to solar wind simulation with a three-dimensional (3D) Solar-InterPlanetary Conservation Element/Solution Element MHD model. The essential focus of our numerical model is devoted to dealing with: (1) the singularity and mesh convergence near the poles via the use of the six-component grid system, (2) the {nabla} {center_dot} B constraint error via an easy-to-use cleaning procedure by a fast multigrid Poisson solver, (3) the Courant-Friedrichs-Levy number disparity via the Courant-number insensitive method, (4) the time integration by multiple time stepping, and (5) the time-dependent boundary condition at the subsonic region by limiting the mass flux escaping through the solar surface. In order to produce fast and slow plasma streams of the solar wind, we include the volumetric heating source terms and momentum addition by involving the topological effect of the magnetic field expansion factor f{sub S} and the minimum angular distance {theta}{sub b} (at the photosphere) between an open field foot point and its nearest coronal hole boundary. These considerations can help us easily code the existing program, conveniently carry out the parallel implementation, efficiently shorten the computation time, greatly enhance the accuracy of the numerical solution, and reasonably produce the structured solar wind. The numerical study for the 3D steady-state background solar wind during Carrington rotation 1911 from the Sun to Earth is chosen to show the above-mentioned merits. Our numerical results have demonstrated overall good agreements in the solar corona with the Large Angle and Spectrometric Coronagraph on board the Solar and Heliospheric Observatory satellite and at 1 AU with WIND observations.

79 ASTRONOMY AND ASTROPHYSICS↗

Solar sensor with autocollimator

Monolithic structure, consisting of fused quartz fabricated solar sensor and autocollimator, measures angle between reference surface on spacecraft and solar vector. Device compensates for errors caused by changes in the alignment of its mountings or component parts. Integrated concept is advantageous whenever sensor mounting errors constitute problems.

Fain, D. L.↗

Solar Power System Evaluated for the Human Exploration of Mars

The electric power system is a crucial element of any mission for the human exploration of the Martian surface. The bulk of the power generated will be delivered to crew life support systems, extravehicular activity suits, robotic vehicles, and predeployed in situ resource utilization (ISRU) equipment. In one mission scenario, before the crew departs for Mars, the ISRU plant operates for 435 days producing liquefied methane and oxygen for ascent-stage propellants and water for crew life support. About 200 days after ISRU production is completed, the crew arrives for a 500-day surface stay. In this scenario, the power system must operate for a total of 1130 days (equivalent to 1100 Martian "sols"), providing 400 MW-hr of energy to the ISRU plant and up to 18 kW of daytime user power. A photovoltaic power-generation system with regenerative fuel cell (RFC) energy storage has been under study at the NASA Glenn Research Center at Lewis Field. The conceptual power system is dominated by the 4000- m2 class photovoltaic array that is deployed orthogonally as four tent structures, each approximately 5 m on a side and 100-m long. The structures are composed of composite members deployed by an articulating mast, an inflatable boom, or rover vehicles, and are subsequently anchored to the ground. Array panels consist of thin polymer membranes with thin-film solar cells. The array is divided into eight independent electrical sections with solar cell strings operating at 600 V. Energy storage is provided by regenerative fuel cells based on hydrogen-oxygen proton exchange membrane technology. Hydrogen and oxygen reactants are stored in gaseous form at 3000 psi, and the water produced is stored at 14.7 psi. The fuel cell operating temperature is maintained by a 40-m2 deployable pumped-fluid loop radiator that uses water as the working fluid. The power management and distribution (PMAD) architecture features eight independent, regulated 600-Vdc channels. Power management and distribution power cables use various gauges of copper conductors with ethylene tetrafluoroethylene insulation. To assess power system design options and sizing, we developed a dedicated Fortran code to predict detailed power system performance and estimate system mass. This code also modeled the requisite Mars surface environments: solar insolation, Sun angles, dust storms, dust deposition, and thermal and ultraviolet radiation. Using this code, trade studies were performed to assess performance and mass sensitivities to power system design parameters (photovoltaic array geometry and orientation) and mission parameters (landing date and landing site latitude, terrain slope, and dust storm activity). Mission analysis cases were also run. Power results are shown in this graph for an analysis case with a September 1, 2012, landing date; 18.95 North latitude landing site; two seasonal dusts storms; and tent arrays. To meet user load requirements and the ISRU energy requirement, an 8-metric ton (MT) power system and 4000-m2 photovoltaic array area were required for the assumed advanced CuInS2 thin-film solar cell technology. In this figure, the top curve is the average daytime photovoltaic array power, the middle curve is average daytime user load power, and the bottom curve is nighttime power. At mission day 1, daytime user power exceeds 120 kW before falling off to 80 kW at the end of the mission. Throughout the mission, nighttime user power is set to the nighttime power requirement. In this analysis, "nighttime" is defined as the 13- to 15-hr period when array power output is below the daytime power requirement. During dust storms, power system capability falls off dramatically so that by mission day 900, a daily energy balance cannot be maintained. Under these conditions, the ISRU plant is placed in standby mode, and the regenerative fuel cell energy storage is gradually discharged to meet user loads.

Kerslake, Thomas W.↗

Contribution of Strong Discontinuities to the Power Spectrum of the Solar Wind

Eight and a half years of magnetic field measurements (2{sup 22} samples) from the ACE spacecraft in the solar wind at 1 A.U. are analyzed. Strong (large-rotation-angle) discontinuities in the solar wind are collected and measured. An artificial time series is created that preserves the timing and amplitudes of the discontinuities. The power spectral density of the discontinuity series is calculated and compared with the power spectral density of the solar-wind magnetic field. The strong discontinuities produce a power-law spectrum in the ''inertial subrange'' with a spectral index near the Kolmogorov -5/3 index. The discontinuity spectrum contains about half of the power of the full solar-wind magnetic field over this ''inertial subrange.'' Warnings are issued about the significant contribution of discontinuities to the spectrum of the solar wind, complicating interpretation of spectral power and spectral indices.

79 ASTRONOMY AND ASTROPHYSICS↗

Effects of drift on the transport of cosmic rays. IV - Modulation by a wavy interplanetary current sheet

The effect of a wavy interplanetary current sheet on the solar modulation of galactic cosmic rays is studied. A simple model of the heliospheric magnetic field is employed in which there is an Archimedean spiral magnetic field directed in one direction above the current sheet and another direction below. The current sheet itself is taken to be the extension by the solar wind of a surface that, at the sun, is a plane inclined at an angle alpha to the solar equator. Two magnetic sectors will therefore be seen by an observer within an angle alpha of the heliographic equator. A simple approximate model is used to investigate modulation. As the tilt angle alpha is increased from zero, it is found that the cosmic-ray intensity decreases. For reasonable variation of alpha from approximately 10 deg to approximately 30 deg, the change in intensity can be compared to that observed as one goes from solar minimum to solar maximum. It is concluded that changes in the waviness of the interplanetary current sheet can have an important, and perhaps dominant, effect in producing solar modulation of galactic cosmic rays.

Jokipii, J. R.↗

Collaborative research. Study of aerosol sources and processing at the GVAX Pantnagar Supersite

The Two Column Aerosol Project (TCAP) investigated uncertainties in the aerosol direct effect in the northern hemisphere mid-latitudes. The University of Colorado 2D-MAX-DOAS and LED-CE-DOAS instruments were collocated with DOE’s Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF) and Mobile Aerosol Observing System (MAOS) during the TCAP-1 campaign at Cape Cod, MA (1 July to 13 August 2012). We have performed atmospheric radiation closure studies to evaluate the use of a novel parameter, i.e., the Raman Scattering Probability (RSP). We have performed first measurements of RSP almucantar scans, and measure RSP in spectra of scattered solar photons at 350nm and 430nm. Radiative Transfer Modelling of RSP demonstrate that the RSP measurement is maximally sensitive to infer even extremely low aerosol optical depth (AOD < 0.01) reliably by DOAS at low solar relative azimuth angles. We further assess the role of elevated aerosol layers on near surface observations of oxygen collision complexes, O 2 -O 2 . Elevated aerosol layers modify the near surface absorption of O 2 -O 2 and RSP. The combination of RSP and O 2 -O 2 holds largely unexplored potential to better constrain elevated aerosol layers and measure column aerosol optical properties such as aerosol effective radius, extinction, aerosol phase functions and refractive indices. The TCAP deployment also provides a time series of reactive trace gas vertical profiles, i.e., nitrogen dioxide (NO 2 ) and glyoxal (C 2 H 2 O 2 ), which are measured simultaneously with the aerosol optical properties by DOAS. NO 2 is an important precursor for ozone (O 3 ) that modifies oxidative capacity. Glyoxal modifies oxidative capacity and is a source for brown carbon by forming secondary organic aerosol (SOA) via multiphase reactions in aerosol and cloud water. We have performed field measurements of these gases during TCAP, and conducted laboratory experiments to quantify for the first time the Setschenow salting constant, KS, of glyoxal in sulfate aerosols. Knowledge about KS is prerequisite to predict how increasing sulfate concentrations since pre-industrial times have modified the formation of SOA from biogenic gases in atmospheric models.

54 ENVIRONMENTAL SCIENCES↗

Mechanisms and observations of coronal dimming for the 201 August 7 event

Coronal dimming of extreme ultraviolet (EUV) emission has the potential to be a useful forecaster of coronal mass ejections (CMEs). As emitting material leaves the corona, a temporary void is left behind which can be observed in spectral images and irradiance measurements. The velocity and mass of the CMEs should impact the character of those observations. However, other physical processes can confuse the observations. We describe these processes and the expected observational signature, with special emphasis placed on the differences. We then apply this understanding to a coronal dimming event with an associated CME that occurred on 2010 August 7. Data from the Solar Dynamics Observatory's Atmospheric Imaging Assembly and EUV Variability Experiment (EVE) are used for observations of the dimming, while the Solar and Heliospheric Observatory's Large Angle and Spectrometric Coronagraph and the Solar Terrestrial Relations Observatory's COR1 and COR2 are used to obtain velocity and mass estimates for the associated CME. We develop a technique for mitigating temperature effects in coronal dimming from full-disk irradiance measurements taken by EVE. We find that for this event, nearly 100% of the dimming is due to mass loss in the corona.

79 ASTRONOMY AND ASTROPHYSICS↗

The dynamic character of the polar solar wind

The Solar and Heliospheric Observatory (SOHO) Large Angle and Spectrometric Coronagraph C2 and Solar Terrestrial Relations Observatory (STEREO) COR2A coronagraph images, when analyzed using correlation tracking techniques, show a surprising result in places ordinarily thought of as 'quiet' solar wind above the poles in coronal hole regions. Instead of the static well-ordered flow and gradual acceleration normally expected, coronagraph images show outflow in polar coronal holes consisting of a mixture of intermittent slow and fast patches of material. We compare measurements of this highly variable solar wind from C2 and COR2A images and show that both coronagraphs measure essentially the same structures. Measurements of the mean velocity as a function of height of these structures are compared with mass flux determinations of the solar wind outflow in the large polar coronal hole regions and give similar results.

79 ASTRONOMY AND ASTROPHYSICS↗

The influence of ozone and aerosols on the brightness and color of the twilight zone

The radiance and color of the twilight sky are calculated for single scattered radiation with the use of spherically symmetric models of the earth's atmosphere. Spherical geometry is used throughout the calculations with no plane parallel approximations. Refraction effects are taken into account through fine subdivision of the atmosphere into spherical shells of fixed index of refraction. Shell's law of refraction is used to calculate a direction of travel each time that a photon traverses the interface between layers. Five different models of the atmosphere were used: a pure molecular scattering atmosphere; molecular atmosphere plus ozone absorption; and three models with aerosol concentrations of 1, 3, and 10 times normal together with molecular scattering and ozone absorption. The results of the calculations are shown for various observation positions and local viewing angles in the solar plane for wavelengths in the range of 0.40 microns to 0.75 microns.

Adams, C. N.↗

Radiation pressure and air drag effects on the orbit of the balloon satellite 1963 30D

Computed orbits of the balloon satellite 1963 30D are given every 2 days over an interval of 456 days near the beginning of the satellite's lifetime and an interval of 824 days near the end of its lifetime. The effects of radiation pressure on the satellite are examined in some detail. It is found that the variations in all the elements can be represented by use of a single parameter to specify the effect of diffuse reflection from the satellite's surface, and that this parameter remains constant, or nearly so, during the entire 7-year lifetime. Success in obtaining a consistent representation of the radiation-pressure effects is ascribed to the inclusion of the effects of terrestrial radiation pressure, using a model for the earth's albedo that includes seasonal and latitudinal variations. Anomalous effects in the orbital acceleration, as well as in the other elements, are represented quite well by including a small force at right angle to the solar direction and by allowing this to rotate about the solar direction. This implies that the satellite is aspherical, that it is rotating, and that the axis of rotation precesses.

Slowey, J. W.↗

The influence of ozone and aerosols on the brightness and color of the twilight sky

The radiance and color of the twilight sky are calculated for single scattered radiation with the use of spherically symmetric models of the earth's atmosphere. Spherical geometry is used throughout the calculations with no plane-parallel approximations. Refraction effects are taken into account through fine subdivision of the atmosphere into spherical shells of fixed index of refraction. Snell's law of refraction is used to calculate a new direction of travel each time that a photon traverses the interface between layers. Five different models of the atmosphere were used: a pure molecular scattering atmosphere; molecular atmosphere plus ozone absorption; and three models with aerosol concentrations of one, three, and ten times normal together with molecular scattering and ozone absorption. The results of the calculations are shown for various observation positions and local viewing angles in the solar plane for wavelengths in the range from 0.40 to 0.75 micron.

Adams, C. N.↗

Determination of stack plume properties from satellite imagery

LANDSAT imagery data were analyzed to determine the quantitative properties of a stack plume emitted from a moderate-sized pulp mill. Overlapping, consecutive-day MSS data provided plume/no plume radiances upwelling from the area of interest. These values from both the plume and its shadow were used to evaluate plume radius, height, particle concentration and scattering function, and total particle loading. Imagery data from a 10 by 10 km region in the vicinity of the mill were normalized to correct for minor atmospheric, solar and viewing angle changes for the two observation days, and cloud shadow data were used to evaluate sky radiance. The effects of the Sun angle, surface reflectance, SNR and spatial resolution are treated in the paper.

Staylor, W. F.↗