An introduction to very large arrays for the Deep Space Network
Explore the source record for details and available documents.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
This paper discusses the array architecture, the resulting challenges in operations, maintenance and sustaining engineering, and preliminary operations concepts to overcome these challenges.
Explore the source record for details and available documents.
This paper discusses the future possibility of a single mission to map an entire planet, compared to the few percent of the surface that can be mapped by today's missions.
An improved suspended-patch antenna has been designed to operate at a frequency of about 23 GHz with linear polarization and to be one of four identical antennas in a rectangular array. The antenna includes a parasitic patch on top of a suspended dielectric superstrate, an active patch on top of a suspended dielectric substrate, a microstrip on the bottom of the dielectric substrate, and a ground plane. The microstrip, the ground plane, the airgap between them, and the dielectric substrate together constitute a transmission line that has an impedance of 50 Ohm and is electromagnetically (EM) coupled to the active patch. The parasitic patch is, in turn, excited by the active patch. The microstrip feed is characterized as inverted because the microstrip is on the bottom of the substrate, whereas microstrips are usually placed on the tops of dielectric substrates
JPL and NASA are in the process of developing ground and spacecraft antenna systems at Ka-band frequencies for future deep space applications. The use of Ka-band (32-GHz down) communication will result in smaller ground and spacecraft antennas and associated equipment, and will provide larger bandwidths necessary for very high data rate communication and radio navigation. In this article, the use of a small phased array as a feed for a reflector antenna system with limited scan capability is addressed. Different feed and antenna configurations, as well as array architectures, are examined. Some theoretical and experimental parameters of a particular breadboard feed array developed by JPL and the University of Massachusetts are presented. Guidelines for the future direction of this effort are provided.
JPL and NASA are in the process of developing ground and spacecraft antenna systems at Ka-band frequencies for future deep space applications. The use of Ka-band (32-GHz) down communication will result in smaller ground and spacecraft antennas and associated equipment, and will provide larger bandwidths necessary for very high data rate communication and radio navigation. In this article, the use of a small phased array as a feed for a reflector antenna system with limited scan capability is addressed. Different feed and antenna configurations, as well as array architectures, are examined. Some theoretical an experimental parameters of a particular breadboard feed array developed by JPL and the University of Massachusetts are presented. Guidelines for the future direction of this effort are provided.
We describe a new architecture for a superconducting detector for the submillimeter and far-infrared. This detector uses a distributed hot-electron transition edge sensor (TES) to collect the power from a focal-plane-filling slot antenna array. The sensors lay directly across the slots of the antenna and match the antenna impedance of about 30 ohms. Each pixel contains many sensors that are wired in parallel as a single distributed TES, which results in a low impedance that readily matches to a multiplexed SQUID readout These detectors are inherently polarization sensitive, with very low cross-polarization response, but can also be configured to sum both polarizations. The dual-polarization design can have a bandwidth of 50The use of electron-phonon decoupling eliminates the need for micro-machining, making the focal plane much easier to fabricate than with absorber-coupled, mechanically isolated pixels. We discuss applications of these detectors and a hybridization scheme compatible with arrays of tens of thousands of pixels.
At submillimeter-wave frequencies, due to the nonavailability of low-loss phase shifters, electronic antenna beam scanning is difficult to realize. Traditionally, power-hungry and bulky motors are used to mechanically scan the antenna beam. At lower-frequencies, phased array antennas are most commonly used where low-loss phase shifters are used with the array elements to accomplish beam steering. However, development of similar phased array antennas at submillimeter-waves has been challenging. Recently, we have developed a low-loss microelectromechanical systems (MEMS) based phased shifter in the 500-750 GHz band. In this work, we present a submillimeter-wave phased array antenna system with a cavity-backed double slot antenna architecture using the MEMS-based phase shifters. To demonstrate the concept, we developed two arrays: first one is a 8×1 linear antenna array with a fixed waveguide feeding network that achieved ±20◦ beam scanning, 18 dB directivity, and less than 1 dB scan loss over the design frequency of 500–570 GHz. The second one is a 4 × 1 linear antenna array with integrated MEMS-based phase shifters on each array element, achieving 15 dB directivity and capable of dynamic beam scanning over a range of ±9 ◦ . All the plots presented are simulated results since the parts are currently being fabricated. We hope to have access to our assembly and measurement facilities over the next few months and present measured performances at the conference.
A circularly polarized feed array for a spacecraft reflector antenna is described that was constructed by using linearly polarized microstrip elements. The array has seven subarrays which form a single cluster as part of a large overlapping cluster reflector feed array. Each of the seven subarrays consists of four linearly polarized microstrip elements. The array achieved a better than 0.8-dB axial ratio at the array pattern peak and better than 3 dB antenna gain to 20 degrees from the peak, across a 7.5 percent frequency bandwidth. A teardrop-shaped feed probe was used to achieve wideband input impedance matching for the relatively thick microstrip substrate. The low impedance and axial ratio bandwidths were achieved using a relatively thick honeycomb substrate with the impedance-matching feed probes.
Variation of radiation pattern of array of two traveling-wave V-antennas and use as spacecraft antenna
As space vehicles become smaller, real estate for allocating the vehicles' instruments and components becomes a premium quantity.
We have developed the first L-band membrane-based active phased array. The antenna is a 16x16 element patch array with dimensions of 2.3mx2.6m. The array uses membrane-compatible Transmit/Receive (T/R) modules for electronic beam steering. We will discuss the antenna design, the fabrication of this large array, the T/R module development, the signal distribution approach and the measured results of the array.
In order to achieve an impedance-matched millimeter-wave integrated horn antenna mixer array, the characteristics of the antenna probes inside the horn must be known. This paper describes impedance measurements for various probes in low-frequency model horns of two different types: (1) a 3 x 3 array made of aluminum by electric discharge machining and (2) a half horn made of copper sheet placed on a big copper-clad circuit board that was used as an image plane. The results of measurements indicate that the presence of the horn increases the effective length of the probe element, in agreement with reports of Guo et al. (1991) and theoretical analysis of Eleftheriades et al. (1991). It was also found that the resonant frequencies can be controlled by changing the length of the probes or by loading the probes.
An Advanced Focal Plane Array ("AFPA") for parabolic dish antennas that exploits spatial diversity to achieve better channel equalization performance in the presence of multipath (better than temporal equalization alone), and which is capable of receiving from two or more sources within a field-of-view in the presence of multipath. The AFPA uses a focal plane array of receiving elements plus a spatio-temporal filter that keeps information on the adaptive FIR filter weights, relative amplitudes and phases of the incoming signals, and which employs an Interference Cancelling Constant Modulus Algorithm (IC-CMA) that resolves multiple telemetry streams simultaneously from the respective aero-nautical platforms. This data is sent to an angle estimator to calculate the target's angular position, and then on to Kalman filters FOR smoothing and time series prediction. The resulting velocity and acceleration estimates from the time series data are sent to an antenna control unit (ACU) to be used for pointing control.
This report summarizes the first year research and development effort leading to development of high-temperature sensors for enhanced geothermal systems. It covers evaluation of ultrasonic and electromagnetic (EM) techniques applied to temperature measurement and flow characterization. On temperature measurement, we have evaluated both microwave radiometry and ultrasonic techniques for temperature gradient and profile measurements. Different antenna designs are evaluated and array loop antenna design is selected for further development. We have also evaluated ultrasonic techniques for total flow characterization, which includes using speed of sound to determine flow temperature, measuring acoustic impedance to estimate fluid density, and using cross-correlation technique to determine the mass flow rate. Method to estimate the flow enthalpy is briefly discussed. At end, the need and proposed techniques to characterize the porosity and permeability of a hot dry rock resource are presented.
The design and performance of satellite phased-array systems are examined by considering several specific antennas built for spacecraft use. Particular consideration is given to: (1) the JARED (Jammer Reduction Antenna System) antenna, and adaptive phased array which can be used to null jammer signals while providing coverage to specific user areas; (2) the algorithm used in the JARED antenna; and (3) a technique that can be used to detect and locate jammers. The antennas used by the Tracking and Data Relay Satellite System (TDRSS) are then described. A significant aspect of the TDRSS is the multiple access antenna which is a 30-element phased array, providing a single steered beam on transmit and the ability to receive data from 20 simultaneous users. Also included on the TDRSS is a mesh deployable reflector and a C-band and K-band communications system.
The DSN is undertaking a major modification of the Mark 3. The modified network described is the Mark 4-A. The DSCC portion of the DSN telemetry system is changed in two major ways as a result of the Mark 4-A DSN implementation. Two 34 meter antennas are added to each deep space communications complex (DSCC). The arraying of those antennas with the existing 64 and 34 meter antennas will provide the equivalent of two separate 64 meter antennas or two 64 meter antennas arrayed together. To accomplish this, the DSCC is modified to provide baseband combining of three 34 meter antennas and one 64 meter antenna. The telemetry system is configured to support either two deep space missions and one highly elliptical orbiter or two highly elliptical orbiters and one deep space mission. Highly elliptical orbiter missions have data rates up to 202 ksps modulated directly on the carrier.