Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Industrial Gas Turbine Engine Catalytic Pilot Combustor-Prototype Testing

PCI has developed and demonstrated its Rich Catalytic Lean-burn (RCL®) technology for industrial and utility gas turbines to meet DOE's goals of low single digit emissions. The technology offers stable combustion with extended turndown allowing ultra-low emissions without the cost of exhaust after-treatment and further increasing overall efficiency (avoidance of after-treatment losses). The objective of the work was to develop and demonstrate emission benefits of the catalytic technology to meet strict emissions regulations. Two different applications of the RCL® concept were demonstrated: RCL® catalytic pilot and Full RCL®. The RCL® catalytic pilot was designed to replace the existing pilot (a typical source of high NOx production) in the existing Dry Low NOx (DLN) injector, providing benefit of catalytic combustion while minimizing engine modification. This report discusses the development and single injector and engine testing of a set of T70 injectors equipped with RCL® pilots for natural gas applications. The overall (catalytic pilot plus main injector) program NOx target of less than 5 ppm (corrected to 15% oxygen) was achieved in the T70 engine for the complete set of conditions with engine CO emissions less than 10 ppm. Combustor acoustics were low (at or below 0.1 psi RMS) during testing. The RCL® catalytic pilot supported engine startup and shutdown process without major modification of existing engine controls. During high pressure testing, the catalytic pilot showed no incidence of flashback or autoignition while operating over a wide range of flame temperatures. In applications where lower NOx production is required (i.e. less than 3 ppm), in parallel, a Full RCL® combustor was developed that replaces the existing DLN injector providing potential for maximum emissions reduction. This concept was tested at industrial gas turbine conditions in a Solar Turbines, Incorporated high-pressure (17 atm.) combustion rig and in a modified Solar Turbines, Incorporated Saturn engine rig. High pressure single-injector rig and modified engine rig tests demonstrated NOx less than 2 ppm and CO less than 10 ppm over a wide flame temperature operating regime with low combustion noise (<0.15% peak-to-peak). Minimum NOx for the optimized engine retrofit Full RCL® designs was less than 1 ppm with CO emissions less than 10 ppm. Durability testing of the substrate and catalyst material was successfully demonstrated at pressure and temperature showing long term stable performance of the catalytic reactor element. Stable performance of the reactor element was achieved when subjected to durability tests (>5000 hours) at simulated engine conditions (P=15 atm, Tin=400C/750F.). Cyclic tests simulating engine trips was also demonstrated for catalyst reliability. In addition to catalyst tests, substrate oxidation testing was also performed for downselected substrate candidates for over 25,000 hours. At the end of the program, an RCL® catalytic pilot system has been developed and demonstrated to produce NOx emissions of less than 3 ppm (corrected to 15% O2) for 100% and 50% load operation in a production engine operating on natural gas. In addition, a Full RCL® combustor has been designed and demonstrated less than 2 ppm NOx (with potential to achieve 1 ppm) in single injector and modified engine testing. The catalyst/substrate combination has been shown to be stable up to 5500 hrs in simulated engine conditions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Conversion of Syngas and CO2 to Light Olefins using Multi-Functional Catalysts

This report describes our effort in developing a novel zeolite encapsulated metal nanoparticle catalyst for the conversion of syngas to light olefins. We have adopted a ligand assisted synthesis protocol in which first metal-amine was prepared using metal salts and suitable amine ligands. The stable metal-amine complex thus prepared was then used as the seed for the growth of zeolite in alkaline solution. We have optimized the synthesis condition as well as different amine ligand to identify the condition to obtain stable metal-amine complex. Upon synthesis of zeolite, metal particles are encapsulated inside the zeolite in a confined space. We have synthesized both Fe and Co catalyst inside silicalite and chabazite zeolite. Catalytic activity of these catalysts were evaluated for syngas conversion reaction and compared with a baseline catalyst. The activity trend of zeolite encapsulated catalyst show very different activity trend compared to the baseline catalyst. While a distribution of products with different carbon number was obtained with baseline catalyst, zeolite encapsulated catalyst show ethylene as the major product. While ~73% selectivity to C 2 -C 6 products were obtained with cahabazite encapsulated Fe catalyst, only 53% selectivity was obtained for the corresponding products with silica-alumina supported Fe catalyst. Not only higher selectivity, Fe-chabazite also produces only C 2 products (ethylene/ethane) while a distribution of products was obtained with Fe-SiAl catalyst. The significantly different reactivity associated with the chabazite encapsulated Fe catalyst was attributed to the confinement effect. We hypothesized that due to the small size of the pore, only ethylene was obtained as the product.

10 SYNTHETIC FUELS↗

Agentic framework for programmatic crystal structure generation using a fine-tuned worker–supervisor large language model

Platinum group metals (PGMs) underpin many catalytic technologies but face severe supply constraints, motivating the search for alternative materials and computational methods to accelerate discovery. While atomistic simulation tools such as Pymatgen and ASE have streamlined structure manipulation, they require detailed inputs, limiting accessibility for experimentalists and slowing early-stage exploration. Here, in this study, we present an AI-driven agentic framework that orchestrates worker–supervisor large language models (LLMs). The worker translates natural-language prompts of varying abstraction into valid crystallographic structures using a compact LLM fine-tuned with low-rank adaptation on a curated text–code–CIF dataset, emphasizing energy-efficient training. Benchmarking against the baseline CodeGen-350M-mono model shows that fine-tuning reduces hallucination rates from 100% to as low as 5% and improves structural match accuracy to up to 82% for fully specified inputs. Accuracy declines with decreasing prompt detail but remains nontrivial even when only stoichiometry and space group are provided, underscoring the LLM’s capacity for crystallographic inference. The supervisor Claude LLM evaluates the outputs and triggers iterative refinement through the worker’s built-in structure manipulation capabilities (e.g., supercell scaling, strain, vacancy, and substitution operations). We further demonstrate use cases for technologically relevant catalysts, including IrO 2 , pyrochlore Pb 2 Ir 2 O 7 , Ni 2 FeO 4 , and Ni 3 Mo, where the framework generates physically consistent structures that can be refined via geometry optimization. This work introduces a low-energy, language-driven pathway for integrating human and machine intelligence in materials design, paving the way for AI-assisted synthesis planning and high-throughput screening of complex oxides.

AI agent↗

Pathway to Complete Energy Sector Decarbonization with Available Iridium Resources using Ultralow Loaded Water Electrolyzers

We present ultralow Ir-loaded (ULL) proton exchange membrane water electrolyzer (PEMWE) cells that can produce enough hydrogen to largely decarbonize the global natural gas, transportation, and electrical storage sectors by 2050, using only half of the annual global Ir production for PEMWE deployment. This represents a significant improvement in PEMWE's global potential, enabled by careful control of the anode catalyst layer (CL), including its mesostructure and catalyst dispersion. Using commercially relevant membranes (Nafion 117), cell materials, electrocatalysts, and fabrication techniques, we achieve at peak a 250× improvement in Ir mass activity over commercial PEMWEs. An optimal Ir loading of 0.011 mg Ir cm -2 operated at an Ir-specific power of ~100 MW kg Ir -1 at a cell potential of ~1.66 V versus RHE (85% higher heating value efficiency). Here, we further evaluate the performance limitations within the ULL regime and offer new insights and guidance in CL design relevant to the broader energy conversion field.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Engineering Atomically Dispersed FeN 4 Active Sites for CO 2 Electroreduction

Atomically dispersed FeN 4 active sites have exhibited exceptional catalytic activity and selectivity for the electrochemical CO 2 reduction reaction (CO2RR) to CO. However, the understanding behind the intrinsic and morphological factors contributing to the catalytic properties of FeN 4 sites is still lacking. By using a Fe-N-C model catalyst derived from the ZIF-8, we deconvoluted three key morphological and structural elements of FeN 4 sites, including particle sizes of catalysts, Fe content, and Fe-N bond structures. Furthermore, their respective impacts on the CO2RR were comprehensively elucidated. Engineering the particle size and Fe doping is critical to control extrinsic morphological factors of FeN 4 sites for optimal porosity, electrochemically active surface areas, and the graphitization of the carbon support. In contrast, the intrinsic activity of FeN 4 sites was only tunable by varying thermal activation temperatures during the formation of FeN 4 sites, which impacted the length of the Fe-N bonds and the local strains. The structural evolution of Fe-N bonds was examined at the atomic level. First-principles calculations further elucidated the origin of intrinsic activity improvement associated with the optimal local strain of the Fe-N bond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Off-Equilibrium Reactivity of Boron-Enriched Metal Diboride Surfaces in Electroreduction Conditions

Boron-based materials, featuring B-dependent reactivity and diverse phases, are emerging as promising catalyst systems. However, the catalytic mechanism on many borides remains poorly understood due to complex surface reconstructions under reaction conditions. Here, we investigate the MoB 2 surface in conditions of hydrogen evolution reaction in acidic media, using grand canonical global optimization, grand canonical density functional theory, ab initio molecular dynamics, free energy surface sampling, and an analytical model for electrochemical barrier evaluation. We propose a boron-enrichment strategy to tune the surface reactivity of the hexagonal face of MoB 2 . We reveal the dynamic nature of the B-enriched surface under H coverage and kinetic trapping of the system in the metastable regime with an extensive examination of the deactivation pathways. The metastable center B site on B-enriched surfaces, featuring buckled-up configuration and a usual relaxation effect, is found to be highly active toward HER via the Volmer–Heyrovsky mechanism. In conclusion, this work demonstrates how off-equilibrium behaviors can arise from the interplay between adsorbate coverage and surface reconstruction on a seemingly simple surface, and we present a theoretical framework and computational workflows to address these behaviors, along with other realistic complexities, in kinetics simulations.

Adsorption↗

Durability Optimization of CO 2 Electrolyzers for Syngas Evolution

Recently, there has been an increased interest in mitigating anthropogenic CO 2 emissions through the electrochemical conversion of CO 2 into fuels and fuel feedstocks, including hydrogen gas (H 2 ), carbon monoxide (CO), and mixtures of the two to yield syngas. Commercial applications of these systems require high catalytic selectivity for the desired products, while exhibiting operational lifetimes exceeding thousands of hours. Advancements in this field have produced systems that display high selectivity of the desired products at faradaic efficiencies exceeding 95%. Despite the advancements made in CO 2 electrolysis, system durability remains a standing challenge in the field. CO 2 electrolyzer lifetimes are often limited by carbonate fouling, catalyst degradation, detrimental flooding of electrode microporous layers and anion exchange membrane (AEM) failures. In this report, a 5 cm 2 membrane electrode assembly (MEA) device is used to investigate potential failure modes and to optimize AEM CO 2 electrolyzer operation. Key findings of this study include the importance of CO 2 flow rate, use of a thin PiperION PTFE-reinforced membrane, optimizing compression to enhance contact under 40 in-lb compression, and the effect of more compressible, commercial iridium oxide anodes on system durability.

Abouremeleh, Mohammed H. [Lawrence Berkeley Nation↗

Surface exsolving perovskite ceramics as catalyst for microwave methane pyrolysis to co-generate hydrogen and carbon nanotube

In this study, we have successfully developed a novel surface exsolving perovskite ceramic, which demonstrates the ability to simultaneously generate CO x -free hydrogen and carbon nanotubes (CNTs) through methane pyrolysis under the influence of microwave irradiation. We conducted an extensive survey and optimization of various perovskite materials specifically tailored for microwave applications. Among the materials investigated, nickel-doped strontium titanium oxide (STON) emerged as the most promising candidate, exhibiting both a satisfactory methane conversion rate and excellent responsiveness to microwave irradiation. Refinement of STON was carried out by fine-tuning the Ni content, optimizing the reduction dwell time, and adjusting the reduction temperature. Notably, SrTiNi 0.08 O 3 (STON8), demonstrated an impressive initial methane conversion rate of up to 40%. Transmission Electron Microscopy (TEM) provided visual evidence of the correlation between Ni content and reduction temperature, with respect to the exsolved Ni metal particle size. This finding highlights the immense potential of surface exsolving perovskite ceramics as a highly effective catalyst for the simultaneous production of CNTs and COx-free hydrogen via methane pyrolysis under microwave irradiation. Furthermore, it represents a step forward in the field of catalytic materials and microwave-driven processes.

08 HYDROGEN↗

Surface basicity controls C–C coupling rates during carbon dioxide-assisted methane coupling over bifunctional Ca/ZnO catalysts

Carbon dioxide-assisted coupling of methane offers an approach to chemically upgrade two greenhouse gases and components of natural gas to produce ethylene and syngas. Prior research on this reaction has concentrated efforts on catalyst discovery, which has indicated that composites comprised of both reducible and basic oxides are especially promising. There is a need for detailed characterization of these bifunctional oxide systems to provide a more fundamental understanding of the active sites and their roles in the reaction. We studied the dependence of physical and electronic properties of Ca-modified ZnO materials on Ca content via X-ray photoelectron and absorption spectroscopies, electron microscopy, and infrared spectroscopic temperature-programmed desorption (IR-TPD). It was found that introduction of only 0.6 mol% Ca onto a ZnO surface is necessary to induce significant improvement in the catalytic production of C 2 species: C 2 selectivity increases from 5% on un-modified ZnO to 58%, at similar conversions. Evidence presented shows that this selectivity increase results from the formation of an interface between the basic CaO and reducible ZnO phases. Furthermore, the basicity of these interface sites correlates directly with catalytic activity over a wide composition range, and this relationship indicates that moderate CO 2 adsorption strength is optimal for CH 4 coupling. These results demonstrate, for the first time to our knowledge, a volcano-type relationship between CO 2 -assisted CH 4 coupling activity and catalyst surface basicity, which can inform further catalyst development.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly stable and ordered intermetallic PtCo alloy catalyst supported on graphitized carbon containing Co@CN for oxygen reduction reaction

A PtCo alloy catalyst was prepared by thermal diffusion of Co encapsulated with thin N-doped carbon layers on graphitic carbon into a Pt lattice (PtCo/NGC). The Co diffused up to the near-Pt surface and resulted in an intermetallic PtCo structure without the leaching process. The intermetallic PtCo structure thermally treated under optimized conditions showed 3-fold higher mass activity than the commercial Pt/C. The potential and maximum power density loss of PtCo/NGC after 30 000 potential cycles were 34 mV and 11%, respectively, which indicated that the PtCo/NGC was remarkably stable when compared to commercial Pt/C and commercial PtCo/GC catalysts. The enhanced catalytic performance and stability of the PtCo/NGC catalyst were attributed to the formation of an intermetallic structure that alleviated the Pt oxidation and Co dissolution. The outstanding performance and stability qualify the ordered intermetallic PtCo/NGC to be a promising cathode catalyst for the commercialization of fuel cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fabrication of a Pillared ZSM-5 Framework for Shape Selectivity of Ethane Dehydroaromatization

Ethane, the second major component of shale gas, is a prospective raw feedstock to valuable chemicals and fuels. Innovative pillared ZSM-5 with various lamellar thicknesses and Si/Al ratios were successfully synthesized with the dual-template method; 0.67 wt % Mo were dispersed over these lamellar ZSM-5, and evaluated for ethane dehydroaromatization. The influence of zeolite morphology and the texture property for the reduction/acidity nature of MoOx species were investigated by X-ray diffraction, scanning electron microscopy, N2-sorption, H2-temperature programmed reduction/oxidation, and NH3-temperature-programmed desorption. The high concentration of acidic sites not only increases ethane conversion and aromatic selectivity, but intensely induces surface coking. Therefore, a moderate Si/Al ratio is utilized to balance catalytic reactivity and stability. Thicker zeolite layers with a long diffusion path exhibited fair ethane conversion, but high aromatization yield. It is of significant importance that the lamellar Mo/MFI catalyst, with Si/Al = 50 and 210 nm layer thickness, demonstrated excellent regenerability during a multicycle reaction/oxidation operation, which could be a promising system for industrial optimization and process deployment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nitrate Reduction Modeling under Acidic Conditions with Late Transition Metals

The electrochemical reduction of nitrate (NO 3 R) to ammonia is a bold yet conceivable way of producing ammonia using renewable electricity. However, serious challenges remain in finding optimal electrocatalysts for the process. An atomistic understanding of the surface energetics behind the NO 3 R is needed in order to design an efficient catalyst. Herein, we combine energetics from density functional theory and microkinetic modeling to demonstrate how surface descriptors can help simplify the search for efficient NO 3 R electrocatalysts. We illustrate the strong correlations between transition-state energetics and O* binding energies for adsorbed nitrate and nitrite on transition metals. For intermediates from NO* and beyond, we compare the benefits of using either the N* or H* binding energies to predict reduction onset potentials. These insights enable us to develop a simple microkinetic model that elucidates the surface coverages of intermediates and the product selectivity of NO 3 R across a range of potentials and transition metals. As a result, we show that the model adequately corroborates with quasi-steady-state rates observed experimentally.

ammonia↗

Achieving industrial ammonia synthesis rates at near-ambient conditions through modified scaling relations on a confined dual site

The production of ammonia through the Haber–Bosch process is regarded as one of the most important inventions of the 20th century. Despite significant efforts in optimizing the process, it still consumes 1 to 2% of the worldwide annual energy for the high working temperatures and pressures. The design of a catalyst with a high activity at milder conditions represents another challenge for this reaction. Herein, we combine density functional theory and microkinetic modeling to illustrate a strategy to facilitate low-temperature and -pressure ammonia synthesis through modified energy-scaling relationships using a confined dual site. Our results suggest that an ammonia synthesis rate two to three orders of magnitude higher than the commercial Ru catalyst can be achieved under the same reaction conditions with the introduction of confinement. Such strategies will open pathways for the development of catalysts for the Haber–Bosch process that can operate at milder conditions and present more economically viable alternatives to current industrial solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Novel Fast Pyrolysis/Catalytic Technology for the Production of Stable Upgraded Liquids

The objective of the proposed research is the demonstration and development of a novel biomass pyrolysis technology for the production of a stable bio-oil. The approach is to carry out catalytic hydrodeoxygenation (HDO) and upgrading together with pyrolysis in a single fluidized bed reactor with a unique two-level design that permits the physical separation of the two processes. The hydrogen required for the HDO will be generated in the catalytic section by the water-gas shift reaction employing recycled CO produced from the pyrolysis reaction itself. Thus, the use of a reactive recycle stream is another innovation in this technology. The catalysts will be designed in collaboration with BASF Catalysts LLC (formerly Engelhard Corporation), a leader in the manufacture of attrition-resistant cracking catalysts. The proposed work will include reactor modeling with state-of-the-art computational fluid dynamics in a supercomputer, and advanced kinetic analysis for optimization of bio-oil production. The stability of the bio-oil will be determined by viscosity, oxygen content, and acidity determinations in real and accelerated measurements. A multi-faceted team has been assembled to handle laboratory demonstration studies and computational analysis for optimization and scaleup.

09 BIOMASS FUELS↗

Efficient low-temperature, catalyst-free dehydrogenation of alkanes

Steam cracking of ethane, a non-catalytic thermochemical process, remains the dominant means of ethylene production. The severe reaction conditions and energy expenditure involved in this process incentivize the search for alternative reaction pathways and reactor designs which maximize ethylene yield while minimizing cost and energy input. According to the present invention, ethylene yields as high as 68% were obtained with a quartz open tube reactor without the use of a catalyst or a cofed stream of oxidizing agents. The open tube reactor design promotes simplicity, low cost, and negligible coke formation. Reactor designs can be optimized to improve the conversion of ethane to ethylene via non-oxidative dehydrogenation, an approach which shows promise for decentralized production of ethylene from natural gas deposits.

Riley, Christopher Ryan↗

Active site design enables industrial scale H 2 O 2 electrosynthesis with metal-free catalysts

The electrosynthesis of hydrogen peroxide (H 2 O 2 ) via a two-electron oxygen reduction reaction enables decentralized H 2 O 2 production. While metal-free carbon catalysts are sustainable and low-cost, their performance is hindered by poorly defined active sites and uncontrolled defect states. Here, we resolve these challenges through active site design and catalyst screening using fluorine (F) and nitrogen (N) codoped carbons as model materials. Statistical analysis combined with density functional theoretical calculations reveals that F-induced structural modification and defect passivation optimize OOH* binding, with F-doping and adjacent F atoms predominantly lowering abs ΔG(OOH*). Experimental results confirm that semi-ionic C–F bonds passivate defects in nitrogen-doped carbon, enhancing catalytic activity and durability. The resulting (N, F)-codoped carbon achieves nearly 100% H 2 O 2 selectivity at 0.5–0.65 V versus the reversible hydrogen electrode and maintains > 95% across 0.01–0.65 V versus the reversible hydrogen electrode. In an electrolyzer, (N, F)-codoped carbon exhibits an H 2 O 2 yield rate of 74.35 mol g cat. −1 h -1 and sustains 300 mA cm -2 for 105 hours with ~95% faradaic efficiency. Coupling the two-electron oxygen reduction reaction with methanol oxidation further reduces cell voltage and enhances productivity. This work provides a means to design efficient catalysts for industrial H 2 O 2 electrosynthesis.

H2O2 electrosynthesis↗