Search NASA⌕ Search

SEARCH · Search NASA

Results for “computer simulation model development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

A Performance Prediction Model for a Fault-Tolerant Computer During Recovery and Restoration

The modeling and design of a fault-tolerant multiprocessor system is addressed. Of interest is the behavior of the system during recovery and restoration after a fault has occurred. The multiprocessor systems are based on the Algorithm to Architecture Mapping Model (ATAMM) and the fault considered is the death of a processor. The developed model is useful in the determination of performance bounds of the system during recovery and restoration. The performance bounds include time to recover from the fault, time to restore the system, and determination of any permanent delay in the input to output latency after the system has regained steady state. Implementation of an ATAMM based computer was developed for a four-processor generic VHSIC spaceborne computer (GVSC) as the target system. A simulation of the GVSC was also written on the code used in the ATAMM Multicomputer Operating System (AMOS). The simulation is used to verify the new model for tracking the propagation of the delay through the system and predicting the behavior of the transient state of recovery and restoration. The model is shown to accurately predict the transient behavior of an ATAMM based multicomputer during recovery and restoration.

Obando, Rodrigo A.↗
NASA NTRS1993

A Novel Method for Characterization of Superconductors: Physical Measurements and Modeling of Thin Films

A method for characterization of granular superconducting thin films has been developed which encompasses both the morphological state of the sample and its fabrication process parameters. The broad scope of this technique is due to the synergism between experimental measurements and their interpretation using numerical simulation. Two novel technologies form the substance of this system: the magnetically modulated resistance method for characterizing superconductors; and a powerful new computer peripheral, the Parallel Information Processor card, which provides enhanced computing capability for PC computers. This enhancement allows PC computers to operate at speeds approaching that of supercomputers. This makes atomic scale simulations possible on low cost machines. The present development of this system involves the integration of these two technologies using mesoscale simulations of thin film growth. A future stage of development will incorporate atomic scale modeling.

Kim, B. F.↗
NASA NTRSDate not supplied

A CFD Framework for Film Boiling and Quenching in Cryogenic Chilldown

Tests of cryogenic chilldown in a vertical stainless steel tube are simulated using computational fluid dynamics (CFD). Subcooled liquid nitrogen enters the room-temperature tube at one end, resulting in film boiling and eventual quenching of the tube walls. A CFD-based modeling framework employing the mixture multiphase model has been developed to simulate this chilldown process and applied to validate it against experimental data. Extensive sensitivity studies have been performed to create a consistent modeling framework, and a two test conditions are simulated to test the modeling capability. The importance of the rewetting temperature and its relation to the foam limit temperature is discussed and is considered in the CFD model. The presented results demonstrate a qualitatively consistent representation of the film boiling and quenching regime. However, the quantitative accuracy of the simulations varies with the test conditions. Simulated vapor volume fraction distributions are also presented, although the current lack of experimental volume fraction data does not permit a comparison.

Computational Fluid Dynamics↗
NASA NTRS1994

NASA High Performance Computing and Communications program

The National Aeronautics and Space Administration's HPCC program is part of a new Presidential initiative aimed at producing a 1000-fold increase in supercomputing speed and a 1(X)-fold improvement in available communications capability by 1997. As more advanced technologies are developed under the HPCC program, they will be used to solve NASA's 'Grand Challenge' problems, which include improving the design and simulation of advanced aerospace vehicles, allowing people at remote locations to communicate more effectively and share information, increasing scientists' abilities to model the Earth's climate and forecast global environmental trends, and improving the development of advanced spacecraft. NASA's HPCC program is organized into three projects which are unique to the agency's mission: the Computational Aerosciences (CAS) project, the Earth and Space Sciences (ESS) project, and the Remote Exploration and Experimentation (REE) project. An additional project, the Basic Research and Human Resources (BRHR) project, exists to promote long term research in computer science and engineering and to increase the pool of trained personnel in a variety of scientific disciplines. This document presents an overview of the objectives and organization of these projects, as well as summaries of early accomplishments and the significance, status, and plans for individual research and development programs within each project. Areas of emphasis include benchmarking, testbeds, software and simulation methods.

Holcomb, Lee↗
NASA NTRS2001

CFD Simulation of Liquid Rocket Engine Injectors

Detailed design issues associated with liquid rocket engine injectors and combustion chamber operation require CFD methodology which simulates highly three-dimensional, turbulent, vaporizing, and combusting flows. The primary utility of such simulations involves predicting multi-dimensional effects caused by specific injector configurations. SECA, Inc. and Engineering Sciences, Inc. have been developing appropriate computational methodology for NASA/MSFC for the past decade. CFD tools and computers have improved dramatically during this time period; however, the physical submodels used in these analyses must still remain relatively simple in order to produce useful results. Simulations of clustered coaxial and impinger injector elements for hydrogen and hydrocarbon fuels, which account for real fluid properties, is the immediate goal of this research. The spray combustion codes are based on the FDNS CFD code' and are structured to represent homogeneous and heterogeneous spray combustion. The homogeneous spray model treats the flow as a continuum of multi-phase, multicomponent fluids which move without thermal or velocity lags between the phases. Two heterogeneous models were developed: (1) a volume-of-fluid (VOF) model which represents the liquid core of coaxial or impinger jets and their atomization and vaporization, and (2) a Blob model which represents the injected streams as a cloud of droplets the size of the injector orifice which subsequently exhibit particle interaction, vaporization, and combustion. All of these spray models are computationally intensive, but this is unavoidable to accurately account for the complex physics and combustion which is to be predicted, Work is currently in progress to parallelize these codes to improve their computational efficiency. These spray combustion codes were used to simulate the three test cases which are the subject of the 2nd International Workshop on-Rocket Combustion Modeling. Such test cases are considered by these investigators to be very valuable for code validation because combustion kinetics, turbulence models and atomization models based on low pressure experiments of hydrogen air combustion do not adequately verify analytical or CFD submodels which are necessary to simulate rocket engine combustion. We wish to emphasize that the simulations which we prepared for this meeting are meant to test the accuracy of the approximations used in our general purpose spray combustion models, rather than represent a definitive analysis of each of the experiments which were conducted. Our goal is to accurately predict local temperatures and mixture ratios in rocket engines; hence predicting individual experiments is used only for code validation. To replace the conventional JANNAF standard axisymmetric finite-rate (TDK) computer code 2 for performance prediction with CFD cases, such codes must posses two features. Firstly, they must be as easy to use and of comparable run times for conventional performance predictions. Secondly, they must provide more detailed predictions of the flowfields near the injector face. Specifically, they must accurately predict the convective mixing of injected liquid propellants in terms of the injector element configurations.

Farmer, Richard↗
NASA NTRSDate not supplied

Forward and Inverse Models for Satellite Remote Sensors using Principal Component Analysis

Satellite remote sensors such as AIRS on Aqua, CrIS on S-NPP, NOAA20 and JPSS-2, IASI on Metop A, B, and C make millions of observations each day with thousands of spectral channels for each observation; this poses challenges for efficiently inversion of the inherently large dataset as needed to retrieve atmospheric and surface properties. This presentation will illustrate the use of Principal Component Analysis (PCA) to speed up radiative transfer forward model calculations and to stabilize the inversion algorithms. A Principal Component-based radiative transfer model (PCRTM) developed at NASA Langley Research Center can simulate top of atmosphere (TOA) radiance or reflectance spectra from 50 cm-1 to 50000 cm-1 (200 m to 0.20 m quickly and accurately. PCRTM demonstrated very high accuracy relative to reference line-by-line radiative transfer models and it saves orders of magnitude computational time. Examples of the PCRTM model developed for hyperspectral sensors such as AIRS, CrIS, IASI, NAST-I, SHIS, CPF, TEMPO, SBG, OMI, and SCIAMACHY will be presented. In addition to using the PCRTM as forward model, the NASA Langley developed inversion algorithm also uses PCA to compress the state vector into a compressed dimension to speed up and stabilize the inversion process. Examples of retrieved atmospheric temperature, water vapor, CO2, CO, CH4, N2O, and O3 profiles, cloud properties (optical depth, size, phase, and height), and surface properties (surface emissivity spectra and skin temperatures) will be presented. This algorithm is being transitioned to the NASA Sounder SIPS and NASA's Goddard Earth Sciences Data and Information Services Center (GES DISC).

forward model↗
NASA NTRS1992

NCC Simulation Model: Simulating the operations of the network control center, phase 2

The simulation of the network control center (NCC) is in the second phase of development. This phase seeks to further develop the work performed in phase one. Phase one concentrated on the computer systems and interconnecting network. The focus of phase two will be the implementation of the network message dialogues and the resources controlled by the NCC. These resources are requested, initiated, monitored and analyzed via network messages. In the NCC network messages are presented in the form of packets that are routed across the network. These packets are generated, encoded, decoded and processed by the network host processors that generate and service the message traffic on the network that connects these hosts. As a result, the message traffic is used to characterize the work done by the NCC and the connected network. Phase one of the model development represented the NCC as a network of bi-directional single server queues and message generating sources. The generators represented the external segment processors. The served based queues represented the host processors. The NCC model consists of the internal and external processors which generate message traffic on the network that links these hosts. To fully realize the objective of phase two it is necessary to identify and model the processes in each internal processor. These processes live in the operating system of the internal host computers and handle tasks such as high speed message exchanging, ISN and NFE interface, event monitoring, network monitoring, and message logging. Inter process communication is achieved through the operating system facilities. The overall performance of the host is determined by its ability to service messages generated by both internal and external processors.

Benjamin, Norman M.↗
NASA NTRS2012

Measurements and Simulations of Surface Dielectric Barrier Discharges Used as Plasma Actuators

This report is a Ph.D. dissertation performed under NRA cooperative agreement and submitted as part of the final report. Asymmetric surface dielectric barrier discharges (DBDs) have shown promise for use as aerodynamic actuators for active flow control. In this project we studied DBD actuators experimentally and numerically. Our DBDs used a symmetric triangular high voltage waveform to generate plasma in atmospheric pressure air. Time-averaged measurements indicated that the induced force of a single barrier actuator design (one electrode insulated from the plasma) can be increased exponentially above the results of previous studies by decreasing both the length and thickness of the electrode exposed to the plasma. This increased force may allow these devices to control flow separation in a wider range of flow environments. Experiments using an intensified digital camera to examine the plasma on time scales of a few nanoseconds showed that, in addition to the previously-observed filamentary and jet-like plasma structures, discharges with very thin exposed electrodes exhibited a weak but constant plasma immediately adjacent to those electrodes. In double-barrier actuators (both electrodes insulated), decreasing the diameter of the narrower electrode lead to increasing forces, and recorded images showed the simultaneous existence of both filamentary and jet-like plasma structures. The development and application of a time-dependent, two-dimensional computational fluid plasma model has aided in understanding the detailed physics of surface DBDs at all-time scales. For simulated single-barrier discharges, the model qualitatively reproduced the filamentary and jet-like micro-discharge structures. The model was somewhat successful in reproducing the observed characteristics of double-barrier actuators. For both actuator geometries, the model indicated that the majority of the forces induced on the neutral gas occur in between micro-discharges as the plasmas decay.

Hoskinson, Alan R.↗
NASA NTRS1980

Digital simulation of dynamic processes in radiometer systems

The development and application of several computer programs for simulating different classes of microwave radiometers are described. The programs are dynamic in nature, and they may be used to determine the instantaneous behavior of system variables as a function of time. Some of the programs employ random variable models in the simulations so that the statistical nature of the results may be investigated. The programs have been developed to utilize either the Continuous System Modeling Program or the Advanced Continuous System Language. The validity of most of the programs was investigated using statistical tests, and the results show excellent correlation with theoretical predictions. The programs are currently being used in the investigation of new design techniques for microwave radiometers.

Stanley, W. D.↗
NASA NTRS1995

Probabilistic simulation of long term behavior in polymer matrix composites

A methodology to compute cumulative probability distribution functions (CDF) of fatigue life for different ratios, r of applied stress to the laminate strength based on first ply failure criteria has been developed and demonstrated. Degradation effects due to long term environmental exposure and mechanical cyclic loads are considered in the simulation process. A unified time-stress dependent multi-factor interaction equation model developed at NASA Lewis Research Center has been used to account for the degradation/aging of material properties due to cyclic loads. Fast probability integration method is used to perform probabilistic simulation of uncertainties. Sensitivity of fatigue life reliability to uncertainties in the primitive random variables are computed and their significance in the reliability based design for maximum life is discussed. The results show that the graphite/epoxy (0/+45/90) deg laminate with ply thickness 0.125 in. has 500,000 cycles life for applied stress to laminate strength ratio of 0.6 and a reliability of 0.999. Also, the fatigue life reliability has been found to be most sensitive to the ply thickness and matrix tensile strength. Tighter quality controls must therefore be enforced on ply thickness and matrix strength in order to achieve high reliability of the structure.

Shah, A. R.↗
NASA NTRSDate not supplied

Airframe Noise Simulations of a Full-Scale Large Civil Transport in Landing Configuration

This paper summarizes the results obtained from an extensive computational campaign to accurately predict full-scale landing gear noise for large civil transports. A highly accurate digital model of a full-scale Boeing 777-300ER aircraft with as-flown nose and main landing gear components was developed for use in the simulations. Two aircraft configurations were selected: nose and main landing gear deployed with wing high-lift devices retracted, and nose and main landing gear deployed with wing high-lift devices deflected. The two configurations were simulated without and with toboggan fairings installed on the main gear to represent the principal configurations evaluated during the 2005 QTD2 flight test. All simulations were performed with the lattice Boltzmann solver PowerFLOW® to resolve and capture the highly complex, unsteady flow field in the immediate vicinity of the aircraft. The far-field noise sig-nature of the aircraft was computed via a Ffowcs-Williams and Hawkings integral approach, with flow quantities on a permeable surface enclosing the source regions used as input. Synthetic pressure records at ground array microphone locations used during the QDT2 test were employed to generate narrowband acoustic maps and integrated far-field noise spectra. With high-lift devices retracted, the predicted spectra showed that landing gear noise is equivalent to total airframe noise, with no other airframe sources appearing within 10 dB of gear peak levels. Application of a toboggan fairing to the main gear produced modest noise reductions of 1-2 dB across the resolved frequency range. With high-lift devices deflected, undercarriage noise was within 3-4 dB of the total airframe noise, thus comprising nearly half of the total airframe noise. For this configuration, the toboggan fairing did not produce a reduction in noise, corroborating trends previously observed in QTD2 flight test data.

airframe noise↗
NASA NTRSDate not supplied

Graphical User Interface (GUI) Implementation for Agent-Based Microbial Radiobiology Model

Sending human life past the Low Earth Orbit (LEO) to explore the Moon and Mars will be challenging. The Earth’s magnetic field naturally protects life from deep-space particle radiation such as Galactic Cosmic Rays (GCR) and Solar Particle Events (SPE); these will pose health risks to humans in deep space. Research has been done to investigate these effects, like BioSentinel, the first biological CubeSat to fly beyond the LEO, designed to culture yeast in a microfluidic device and record optical measurements of growth and metabolism. However, experiments can only report cell damage as bulk growth curves, while deep-space radiation causes damage that is heterogeneous among individual cells. AMMPER is an open-source, agent-based, computational model coded in Python to simulate the effects of deep-space radiation on individual yeast cells (Saccharomyces cerevisiae) to facilitate interpretation of biological radiation experiments. Version 1.0 of the code ran in a command line interface (CLI), limiting use to those familiar with modularization, object-oriented programming, and computational models. Here we present a graphical user interface (GUI) for AMMPER to increase its accessibility. GUI development included converting input points and UI files, designing an application and logo, and expanding program packages. Additionally, we added optical assistance that corresponded with simulation parameters, which included simulation type, cell type, ROS model, and radiation dosage, as well as customizable display and file exportation features. Following a pilot testing period, its structure was updated further to enhance abilities, adding increased runs, video visualization, data plotting, and an educational/tutorial component. Future work will include creating a bit installer and runtime environment for AMMPER. Ultimately, the creation of the GUI has two main goals: to facilitate the integration of computational models into the work of researchers in microbial radiobiology, and to act as an interactive and visual resource for space biology education.

yeast↗
NASA NTRS2008

Status of the AIAA Modeling and Simulation Format Standard

The current draft AIAA Standard for flight simulation models represents an on-going effort to improve the productivity of practitioners of the art of digital flight simulation (one of the original digital computer applications). This initial release provides the capability for the efficient representation and exchange of an aerodynamic model in full fidelity; the DAVE-ML format can be easily imported (with development of site-specific import tools) in an unambiguous way with automatic verification. An attractive feature of the standard is the ability to coexist with existing legacy software or tools. The draft Standard is currently limited in scope to static elements of dynamic flight simulations; however, these static elements represent the bulk of typical flight simulation mathematical models. It is already seeing application within U.S. and Australian government agencies in an effort to improve productivity and reduce model rehosting overhead. An existing tool allows import of DAVE-ML models into a popular simulation modeling and analysis tool, and other community-contributed tools and libraries can simplify the use of DAVE-ML compliant models at compile- or run-time of high-fidelity flight simulation.

Jackson, E. Bruce↗
NASA NTRS2010

A Principal Component-Based Radiative Transfer Forward Model (PCRTM) for Vertically in Homogeneous Cloud

A principal-component based radiative transfer model (PCRTM) is developed for simulating the infrared spectral radiance at the top of the atmosphere (TOA). The PCRTM approach removes the redundancy in radiative transfer calculation in high resolution infrared spectra, and saves significant amount of computational time with great accuracy. In PCRTM, both ice and water clouds are treated as effective transmissivity and reflectivity stored in a pre-calculated lookup tables. These quantities are calculated using cloud single scattering properties such as cloud optical depth, cloud particle size, cloud phase, etc. The cloud can be inserted into any pressure layer in the PCRTM model (up to 100 layers). The effective temperature of each cloud layer is treated as a function of its optical depth. To test the accuracy of this approximation, the results are compared with the more rigorous DISORT model, which treats cloud as a plane parallel layer. The root-mean-square error of PCRTM, with respect to DISORT results, is generally less than 0.5 K in brightness temperature. However, the CPU time required by PCRTM was approximately two orders of magnitude less than that required by DISORT.

Li, Hui↗
NASA NTRS2017

Simulation of Guided-Wave Ultrasound Propagation in Composite Laminates: Benchmark Comparisons of Numerical Codes and Experiment

Ultrasonic wave methods constitute the leading physical mechanism for nondestructive evaluation (NDE) and structural health monitoring (SHM) of solid composite materials, such as carbon fiber reinforced polymer (CFRP) laminates. Computational models of ultrasonic wave excitation, propagation, and scattering in CFRP composites can be extremely valuable in designing practicable NDE and SHM hardware, software, and methodologies that accomplish the desired accuracy, reliability, efficiency, and coverage. The development and application of ultrasonic simulation approaches for composite materials is an active area of research in the field of NDE. This paper presents comparisons of guided wave simulations for CFRP composites implemented using four different simulation codes: the commercial finite element modeling (FEM) packages ABAQUS, ANSYS, and COMSOL, and a custom code executing the Elastodynamic Finite Integration Technique (EFIT). Benchmark comparisons are made between the simulation tools and both experimental laser Doppler vibrometry data and theoretical dispersion curves. A pristine and a delamination type case (Teflon insert in the experimental specimen) is studied. A summary is given of the accuracy of simulation results and the respective computational performance of the four different simulation tools.

Composite↗
NASA NTRS2019

Challenges in Qualification of Thermal Protection Systems in Extreme Entry Environments

Planetary entry vehicles employ ablative TPS materials to shield the aeroshell from entry aeroheating environments. To ensure mission success, it must be demonstrated that the heat shield system, including local features such as seams, does not fail at conditions that are suitably margined beyond those expected in flight. Furthermore, its thermal response must be predictable, with acceptable fidelity, by computational tools used in heat shield design. Mission assurance is accomplished through a combination of ground testing and material response modelling. A material's robustness to failure is verified through arcjet testing while its thermal response is predicted by analytical tools that are verified against experimental data. Due to limitations in flight-like ground testing capability and lack of validated high-fidelity computational models, qualification of heat shield materials is often achieved by piecing together evidence from multiple ground tests and analytical simulations, none of which fully bound the flight conditions and vehicle configuration. Extreme heating environments (>2000 W/sq. cm heat flux and >2 atm pressure), experienced during entries at Venus, Saturn and Ice Giants, further stretch the current testing and modelling capabilities for applicable TPS materials. Fully-dense Carbon Phenolic was the material of choice for these applications; however, since heritage raw materials are no longer available, future uses of re-created Carbon Phenolic will require re-qualification. To address this sustainability challenge, NASA is developing a new dual-layer material based on 3D weaving technology called Heat shield for Extreme Entry Environments (HEEET). Regardless of TPS material, extreme environments pose additional certification challenges beyond what has been typical in recent NASA missions. Scope of this presentation: This presentation will give an overview of challenges faced in verifying TPS performance at extreme heating conditions. Examples include: (1) Bounding aeroheating parameters (heat flux, pressure, shear and enthalpy) in ground facilities. How to certify TPS if environments can't be bounded or aeroheating parameters can't be simultaneously achieved. (2) Higher uncertainties in ground test environments (facility calibration and analytical predictions) at extreme conditions. (3) Testing in flows similar to planetary atmosphere composition (H2/He for Gas and Ice Giants). (4) Test sample size limitations for qualifying seam designs. (5) Lack of computational tools capable of simulating all significant aspects of TPS performance (including initiation and propagation of failures). This presentation will provide recommendations on how the EDL community can address these challenges and mitigate some of the risks involved in flying TPS materials at extreme conditions. Examples include: (1) Dedicated activity to understanding TPS failure modes. Develop computational tools capable of modelling fluid interaction with material's thermostructural response. Validate these tools through failure testing. A better understanding of failure mechanisms may eliminate the need to fully bound all aeroheating parameters in ground testing. (2) Enhancements to current testing facilities to simulate flight-like ablation mechanism (ex. testing in Nitrogen at Ames Interaction Heating Facility to limit oxidation in favor of more sublimation). (3) Improved characterization of test conditions with new diagnostic methods and determination of environment uncertainty through rigorous statistical analysis of available data. (4) Design margin policies that are directly tied to uncertainties in ground test environments and modelling fidelity

Mahzari, Milad↗
NASA NTRS2007

Integrating Human Factors into Crew Exploration Vehicle Design

With NASA's new Vision for Exploration to send humans beyond Earth orbit, it is critical to consider the human as a system that demands early and continuous user involvement, and an iterative prototype/test/redesign process. Addressing human-system interface issues early on can be very cost effective even cost reducing when performed early in the design and development cycle. To achieve this goal within Crew Exploration Vehicle (CEV) Project Office, human engineering (HE) team is formed. Key tasks are to apply HE requirements and guidelines to hardware/software, and provide HE design, analysis and evaluation of crew interfaces. Initial activities included many practice-orientated evaluations using low-fidelity CEV mock-ups. What follows is a description of such evaluations that focused on a HE requirement regarding Net Habitable Volume (NHV). NHV is defined as the total remaining pressurized volume available to on-orbit crew after accounting for the loss of volume due to deployed hardware and structural inefficiencies which decrease functional volume. The goal of the NHV evaluations was to develop requirements providing sufficient CEV NHV for crewmembers to live and perform tasks in support of mission goals. Efforts included development of a standard NHV calculation method using computer models and physical mockups, and crew/ stakeholder evaluations. Nine stakeholders and ten crewmembers participated in the unsuited evaluations. Six crewmembers also participated in a suited evaluation. The mock-up was outfitted with volumetric representation of sub-systems such as seats, and stowage bags. Thirteen scenarios were developed to represent mission/crew tasks and considered to be primary volume drivers (e.g., suit donning) for the CEV. Unsuited evaluations included a structured walkthrough of these tasks. Suited evaluations included timed donning of the existing launch and entry suit to simulate a contingency scenario followed by doffing/ stowing of the suits. All mockup evaluations were videotaped. Structured questionnaires were used to document user interface issues and volume impacts of layout configuration. Computer model and physical measures of the NHV agreed within 1 percent. This included measurement of the gross habitable volume, subtraction of intrusive volumes, and other non-habitable spaces. Calculation method developed was validated as a standard means of measuring NHV, and was recommended as a verification method for the NHV requirements. Evaluations confirmed that there was adequate volume for unsuited scenarios and suit donning/ doffing activity. Seats, suit design stowage and waste hygiene system noted to be critical volume drivers. The low-fidelity mock-up evaluations along with human modeling analysis generated discussions that will lead to high-level systems requirements and human-centered design decisions. This approach allowed HE requirements and operational concepts to evolve in parallel with engineering system concepts and design requirements. As the CEV design matures, these evaluations will continue and help with design decisions, and assessment, verification and validation of HE requirements.

Whitmore, Mihriban↗
NASA NTRS1993

Particle kinetic simulation of high altitude hypervelocity flight

In this grant period, the focus has been on enhancement and application of the direct simulation Monte Carlo (DSMC) particle method for computing hypersonic flows of re-entry vehicles. Enhancement efforts dealt with modeling gas-gas interactions for thermal non-equilibrium relaxation processes and gas-surface interactions for prediction of vehicle surface temperatures. Both are important for application to problems of engineering interest. The code was employed in a parametric study to improve future applications, and in simulations of aeropass maneuvers in support of the Magellan mission. Detailed comparisons between continuum models for internal energy relaxation and DSMC models reveals that several discrepancies exist. These include definitions of relaxation parameters and the methodologies for implementing them in DSMC codes. These issues were clarified and all differences were rectified in a paper (Appendix A) submitted to Physics of Fluids A, featuring several key figures in the DSMC community as co-authors and B. Haas as first author. This material will be presented at the Fluid Dynamics meeting of the American Physical Society on November 21, 1993. The aerodynamics of space vehicles in highly rarefied flows are very sensitive to the vehicle surface temperatures. Rather than require prescribed temperature estimates for spacecraft as is typically done in DSMC methods, a new technique was developed which couples the dynamic surface heat transfer characteristics into the DSMC flow simulation code to compute surface temperatures directly. This model, when applied to thin planar bodies such as solar panels, was described in AIAA Paper No. 93-2765 (Appendix B) and was presented at the Thermophysics Conference in July 1993. The paper has been submitted to the Journal of Thermophysics and Heat Transfer. Application of the DSMC method to problems of practical interest requires a trade off between solution accuracy and computational expense and limitations. A parametric study was performed and reported in AIAA Paper No. 93-2806 (Appendix C) which assessed the accuracy penalties associated with simulations of varying grid resolution and flow domain size. The paper was also presented at the Thermophysics Conference and will be submitted to the journal shortly. Finally, the DSMC code was employed to assess the pitch, yaw, and roll aerodynamics of the Magellan spacecraft during entry into the Venus atmosphere at off-design attitudes. This work was in support of the Magellan aerobraking maneuver of May 25-Aug. 3, 1993. Furthermore, analysis of the roll characteristics of the configuration with canted solar panels was performed in support of the proposed 'Windmill' experiment. Results were reported in AIAA Paper No. 93-3676 (Appendix D) presented at the Atmospheric Flight Mechanics Conference in August 1993, and were submitted to Journal of Spacecraft and Rockets.

Haas, Brian L.↗