Search NASA⌕ Search

SEARCH · Search NASA

Results for “cosmology of theories beyond the SM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,724 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Energy-Optimal Vehicle Longitudinal Motion Control via Pontryagin’s Minimum Principle and Ultra-Local Model

Longitudinal vehicle motion control is essential for enhancing performance and optimizing a vehicle’s energy usage. However, it remains a challenging task due to the nonlinear and uncertain nature of vehicle dynamics, along with varying driving conditions. This paper presents a novel ultra-local optimal control approach based on Pontryagin’s Minimum Principle (PMP) that circumvents the need for detailed system identification by employing an ultra-local model. The control objective is to minimize the total energy consumption under boundary conditions while ensuring smooth traction force generation. The proposed approach is evaluated using a high-fidelity vehicle model in three representative scenarios: (i) nominal driving, (ii) a change in tire road friction coefficient (TRFC) from 0.5 to 0.65 and road slope from 0% to 5% during the maneuver, with target velocity unchanged, and (iii) a change in target velocity from 20 m/s to 0 m/s during the maneuver, while maintaining nominal TRFC and slope conditions. The simulation results demonstrate that the proposed method delivers robust performance, effectively balancing consumption and tracking accuracy in all tested scenarios.

Waleed khan, Muhammad [The University of Texas at ↗
DOE OSTI2026

Treatment of Lagoon Dairy Manure Wastewater via Iron Electrocoagulation, Microfiltration, and Adsorption

Dairy manure wastewater generated by flushing barn cow waste contains nutrients, pathogens, and organic and inorganic contaminants. This study utilized a process consisting of iron electrocoagulation (Fe-EC), microfiltration (MF), and activated carbon (AC) adsorption to treat farm wastewater and explore the reclamation of clean water for irrigation and livestock consumption. Significant removal (>99.9%) of chemical oxygen demand (COD), total organic carbon (TOC), phosphorus (P), turbidity, and microorganisms, as well as ions including magnesium, calcium, sulfur, and silica was achieved by the combined EC-MF-AC process. Specifically, a charge loading of ∼37,500 C/L in a continuous-flow EC configuration, followed by MF, achieved more than 95% removal of TOC and COD. Characterization of produced flocs and foam via scanning-electron microscopy with energy-dispersal spectroscopy and Fourier transform infrared spectroscopy confirmed the removal of ions, including calcium, sulfur, and silica. A key finding was the electrocatalytic conversion of nitrogen species to ammonia gas through the intermediate reduction of nitrate/nitrite, which led to ∼60% total nitrogen (TN) removal. AC treatment further improved TN removal to ∼70%. The Fe-EC process also eradicated >99.9% of bacteria. Preliminary process cost assessment, based on recycled materials for EC electrodes, showed significant cost savings (∼2 times) compared to commercial electrodes.

Dutta, Swapnamoy [ORNL]↗
DOE OSTI2023

Flame retardant biogenic building insulation materials from hemp fiber

Biogenic thermal insulation materials are in high demand because of its carbon-sequestration nature. However, high flammability, moisture condensation, and relatively high thermal conductivity of biogenic material are major concerns for sustainable building applications. In this study, we report the fire-retardant cellulose xerogel insulation nanocomposites derived from hemp fiber recycling and silica xerogel, in which the boric acid treatment improves its fire retardancy. The as-prepared materials show a low thermal conductivity of 31.3 mW/m K, high flexural modulus of 665 MPa, hydrophobicity with the water contact angle of 115°, and fire retardancy with 30% weight loss over a period of burning time 10 min. Overall, this work provides an effective method for the synthesis of fire-retardant biogenic thermal insulation materials and shows a promising way for next-generation bio-based insulation materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Surface deposition of nanometer scale carbon structures on Bi 2 Sr 2 CaCu 2 O 8+δ using a low-cost scanning electron microscope

In this work, we investigate optically active nanostructures on Bi 2 Sr 2 CaCu 2 O 8+δ (BSCCO). The nanostructures are constructed from carbon nanocrystals formed using the electron beam of a scanning electron microscope to locally decompose residual hydrocarbons at the BSCCO surface. Atomic force microscopy is used to characterize the dimensions of these structures as a function of beam exposure time. This technique has been used to induce localized intercalation to form carbon nanoparticles up to tens of nanometers into a variety of 2D materials. Cross-sectional scanning transmission electron microscopy in BSCCO shows the presence of these carbon deposits on the surface, but there is no evidence they penetrate into the BSCCO substrate. Therefore, this technique is not suitable for localized intercalation in BSCCO, and it does have promise as a cost-effective approach to pattern nanometer scale etch stops.

2D materials↗
DOE OSTI2024

Selective solid-state isolation of NMR circuit elements using back-to-back field effect transistors

Nuclear Magnetic Resonance (NMR) electronics that employ selective solid-state isolation of circuit elements can include solid-state switches, such as back-to-back Field Effect Transistor (FET) pairs, and isolated gate drive electronics adapted to operate the solid-state switches in order to selectively decouple induction coils from receive electronics. The solid-state switches can be placed in series to achieve higher standoff voltages, and can be configured for low on resistance and short switching times. The gate drive electronics can include electrical isolation components adapted to enhance standoff voltages and reduce electrical noise at the selectively isolated receive electronics.

Walsh, David O.↗
DOE OSTI2026

Entropy-defect synergy for dual luminescence mechanism in spinel: Time-resolved anti-counterfeiting and fingerprint visualization

Multimodal luminescent materials, while promising for anti-counterfeiting, often lack dynamic time-dependent responses and controllable spatial distribution, limiting their encryption capabilities in the spatiotemporal dimension. Here, this work presents a coordinated control strategy based on entropy and defect engineering, and uses a backpropagation (BP) neural network for material screening to successfully prepare spinel Mg 0.8 (Fe 0.04 Co 0.04 Ni 0.04 Cu 0.04 Zn 0.04 )Cr 2 O 4 (MgA 5 CO) phosphors with time-dependent dynamic luminescence behavior. This phosphor simultaneously activated the d-d transition luminescence (∼618 nm) derived from Co 2+ /Cr 3+ and the defect luminescence (∼398 nm) related to zinc vacancies (V Zn ) in a single-phase solid solution. The phosphor exhibits a time-dependent color evolution from pink to purple under fixed-wavelength excitation, due to the different excited-state dynamics and decay lifetimes associated with the d-d transition and defect luminescence. Structural characterization and spectral analysis confirmed the existence of V Zn and its significant role in defect luminescence process. The fluorescent and dynamic luminescent properties of entropy-based spinel oxide enable its use in advanced anti-counterfeiting applications like fingerprint recognition and color-changing dedicated anti-counterfeiting mark, showing promise in high-end and time-dynamic anti-counterfeiting fields. This research not only developed a new type of fluorescent dynamic anti-counterfeiting material, but also provided a new idea for constructing advanced optical functional materials with multiple luminescence mechanisms.

Defect project↗
DOE OSTI2026

Atomic Evolution of Hydrogen Intercalation Wave Dynamics in Palladium Nanocrystals Revealed by Liquid-Phase Transmission Electron Microscopy

Solute-intercalation-induced phase separation creates spatial heterogeneities in host materials, a phenomenon ubiquitous in batteries, hydrogen storage, and other energy devices. Despite many efforts, probing intercalation processes at the atomic scale has been a significant challenge. By utilizing liquid-phase transmission electron microscopy (TEM), we study hydrogen (de)intercalation in palladium nanocrystals as a model system and have achieved unprecedented atomic-resolution imaging of hydrogen intercalation wave dynamics. Our observations reveal that intercalation wave mechanisms, instead of shrinking-core mechanisms, prevail at ambient temperature for palladium nanocubes ranging from ∼60 nm down to ∼10 nm. Systematic image analysis uncovers the atomic evolution of the hydrogen intercalation wave, transitioning from nonplanar and inclined boundaries to those closely aligned with {100} planes. Our kinetic Monte Carlo simulations demonstrate that the observed intercalation wave dynamics correspond to sorption pathways minimizing the lattice mismatch strain at the phase boundary. In conclusion, unveiling the atomic intercalation pathways holds profound implications for engineering intercalation-mediated devices and advancements in energy sciences.

Lee, Daewon [Lawrence Berkeley National Laboratory↗
DOE OSTI2026

Two-mode bosonic quoctit for high energy physics

In this work, we study a two-mode bosonic encoding of a quoctit inside a non-Abelian group-structured constellation of coherent states. This work is motivated by the importance of non-Abelian symmetry in particle physics and the desire to have transversal non-Abelian logical gates. We use the previously developed 2 T constellation of states used to encode a so-called 2 T qutrit. The fidelity of the 2 T quoctit is benchmarked against other bosonic qudits for different noise models and find it compare favorably when power constraints are considered. This paves the way for the construction of higher-dimensional qudits (e.g., a quicosotetrit with 2 T group structure) in bosonic systems with practical applications in quantum simulations of particle physics.

Kürkçüoglu, Doga Murat [Fermilab] (ORCID:000000031↗
DOE OSTI2026

Mitigating Hydrogen-Induced Degradation of Iridium Anodes in Proton Exchange Membrane Water Electrolyzers

One promising method for reducing precious metal usage in proton exchange membrane water electrolysis is lowering iridium (Ir) loading at the anode. However, low-loading Ir catalysts often suffer from poor stability under high current densities. In this study, hydrogen (H2) crossover from the cathode to the anode is identified as a key degradation pathway. Temperature-programmed reduction confirms the reduction of IrO2 at 80 °C in a hydrogen environment, highlighting the vulnerability of IrO2-based catalysts to H2 exposure. To mitigate this effect, palladium (Pd) is introduced as an anode additive, acting as an H2 oxidation catalyst and mitigating IrO2 reduction. This protective role is verified by inductively coupled plasma optical emission spectroscopy and in situ X-ray absorption spectroscopy, showing significantly suppressed Ir dissolution at 80 °C under H2 flow when an O-covered Pd surface is present at oxygen evolution reaction potentials. Results from the current study identify a new strategy in improving activity and durability of catalysts in electrolyzers.

58 GEOSCIENCES↗
DOE OSTI2026

Oversizing and Part-Load Problems

Oversizing, the common engineering practice of specifying devices with capacity exceeding the actual load requirement, is a widespread practice across virtually all building technologies end-use categories, including HVAC, electrical systems, lighting, appliances, and plug loads. This practice, driven by factors like design uncertainty, institutional pressures, and risk aversion, results in wasted capital investment, control difficulties, and excessive energy consumption due to inefficient part-load operation. Part-load operation, where devices run below maximum capacity, is the dominant operating mode in most energy systems and presents a complex design challenge. Solutions to match output to load fall into three broad categories: constraining the output, adjusting the device’s internal behavior, and linking output to energy storage or other waste-heat reuse applications. The energy implications of part-load are critical, as efficiency often drops sharply as load decreases across a wide diversity of devices. To quantify the extent of this problem, we derive a dimensionless Part-Load Metric (PLM) based on device efficiency and its frequency distribution of operating hours at various output levels. The PLM quantifies the deviation of a device's actual efficiency from its maximum design efficiency. This metric also serves as a measure of "capital inefficiency," enabling engineers to compare the impact of different part-load solutions and providing a unified framework for evaluating performance across various devices and systems.

Meier, Alan↗
DOE OSTI2024

A novel digital lifecycle for Material‐Process‐Microstructure‐Performance relationships of thermoplastic olefins foams manufactured via supercritical fluid assisted foam injection molding

Abstract This research significantly enhances the applicability of thermoplastic olefins (TPOs) in the automotive industry using supercritical N 2 as a physical foaming agent, effectively addressing the limitations of traditional chemical agents. It merges experimental results with simulations to establish detailed material‐process‐microstructure‐performance (MP2) relationships, targeting 5–20% weight reductions. This innovative approach labeled digital lifecycle (DLC) helps accurately predict tensile, flexural, and impact properties based on the foam microstructure, along with experimentally demonstrating improved paintability. The study combines process simulations with finite element models to develop a comprehensive digital model for accurately predicting mechanical properties. Our findings demonstrate a strong correlation between simulated and experimental data, with about a 5% error across various weight reduction targets, marking significant improvements over existing analytical models. This research highlights the efficacy of physical foaming agents in TPO enhancement and emphasizes the importance of integrating experimental and simulation methods to capture the underlying foaming mechanism to establish material‐process‐microstructure‐performance (MP2) relationships. Highlights Establishes a material‐process‐microstructure‐performance (MP2) for TPO foams Sustainably produces TPO foams using supercritical (ScF) N 2 with 20% lightweighting Shows enhanced paintability for TPO foam improved surface aesthetics Digital lifecycle (DLC) that predicts both foam microstructure and properties DLC maps process effects & microstructure onto FEA mesh for precise prediction

Engineering↗
DOE OSTI2024

3D Printing ofThermally Responsive Shape Memory LiquidCrystalline Epoxy Networks

Abstract A two-component liquid crystalline epoxy network (LCEN) with shape memory behavior was developed and evaluated as a candidate material for 3D printing. The cure kinetics of the uncured material and the shape memory properties of the cured LCEN were investigated by using parallel plate rheology and dynamic mechanical analysis, respectively. A commercially available fumed silica additive was introduced to the neat, uncured material to improve the rheological properties for 3D printing. The addition of fumed silica was found to increase the yield stress, shear-thinning behavior, and toughness of the uncured epoxy ink. Polarized light microscopy, differential scanning calorimetry, and wide-angle X-ray scattering measurements between the neat and additive-modified LCEN suggested a reduction in liquid crystalline alignment in the modified LCEN, owing to interactions between crystalline domains and fumed silica, which in turn influenced the mechanical behavior. Overall, the additive was found to be successful in preserving the shape memory properties of LCEN while improving its printability.

Chemistry↗
DOE OSTI2026

Electron/hadron separation with the TRD based on GaAs pixel detectors

Transition Radiation Detectors (TRDs) are widely used for particle identification in both high-energy physics and astroparticle physics. They are typically equipped with gaseous detectors. The main limitation of these types of detectors is that TR photons and ionization losses cannot be decoupled, which significantly reduces the particle separation power. Recent advancements in the development of pixel detectors based on GaAs sensors offer a unique opportunity to effectively detect TR photons and separate them from ionization losses. Such detectors represent novel devices that combine precise tracking capabilities with particle identification (PID) properties. The present work is dedicated to an experimental study of particle identification properties of the TRD prototype based on 500 μ m-thick GaAs sensor bonded to a Timepix3 chip. Studies were performed at the CERN SPS and it was shown that at a particle momentum of 20 GeV/c, the probability of misidentifying a hadron as an electron is below 10 −2 for an electron detection efficiency of 98%–99%, and it is 1 . 6⋅10 −4 for electron detection efficiency of 90%. This performance surpasses the electron/hadron rejection power of all known TRDs by an order of magnitude for the same detector length.

GaAs detectors↗
DOE OSTI2026

Advancing technologies for lignin-based jet fuel production in aqueous phase

Integrating lignin into a cellulosic ethanol plant for the co-production of lignin-based jet fuel (LJF) in aqueous phase offers a significant opportunity to boost operational efficiency, economic viability, carbon conversion, and the overall sustainability of biofuel and chemical production. LJF is lignin-structure-based jet fuel blendstocks primarily composed of alkyl-substituted mono-, bi-, and tri-cyclohexanes. It exhibits high energy density, potential for low emissions, and favourable blend characteristics that comply with drop-in specifications. An overview of lignin feedstock, catalytic processes, LJF chemical compositions, fuel properties tests, and techno-economic analysis (TEA) and life cycle assessment (LCA) indicate that (1) the reactivity of lignin plays a crucial role in its structure transformation to LJF molecules; (2) catalytic processing of lignin to LJF can occur through a simultaneous depolymerization and hydrodeoxygenation process, bypassing the intermediate step of producing and upgrading lignin-derived oil; (3) LJF's uniqueness molecules making it more promising for high energy content and low emission jet fuel properties for next generation sustainable aviation fuel (SAF); and (4) TEA and LCA demonstrate that LJF is not only potentially cost-effective but also offers favourable carbon footprint compared to other SAFs. In conclusion, this review highlights the most recent advancements in LJF technology, along with the challenges and opportunities that lie ahead in fulfilling its potential.

09 BIOMASS FUELS↗
DOE OSTI2025

Wave ripples formed in ancient, ice-free lakes in Gale crater, Mars

Symmetrical wave ripples identified with NASA’s Curiosity rover in ancient lake deposits at Gale crater provide a key paleoclimate constraint for early Mars: At the time of ripple formation, climate conditions must have supported ice-free liquid water on the surface of Mars. These features are the most definitive examples of wave ripples on another planet. The ripples occur in two stratigraphic intervals within the orbitally defined Layered Sulfate Unit: a thin but laterally extensive unit at the base of the Amapari member of the Mirador formation, and a sandstone lens within the Contigo member of the Mirador formation. In both locations, the ripples have an average wavelength of ~4.5 centimeters. Internal laminae and ripple morphology show an architecture common in wave-influenced environments where wind-generated surface gravity waves mobilize bottom sediment in oscillatory flows. Their presence suggests formation in a shallow-water (<2 meters) setting that was open to the atmosphere, which requires atmospheric conditions that allow stable surface water.

Science & Technology - Other Topics↗
DOE OSTI2025

Divergent evolution of slip banding in CrCoNi alloys

Abstract Metallic materials under high stress often exhibit deformation localization, manifesting as slip banding. Over seven decades ago, Frank and Read introduced the well-known model of dislocation multiplication at a source, explaining slip band formation. Here, we reveal two distinct types of slip bands (confined and extended) in compressed CrCoNi alloys through multi-scale testing and modeling from microscopic to atomic scales. The confined slip band, characterized by a thin glide zone, arises from the conventional process of repetitive full dislocation emissions at Frank–Read source. Contrary to the classical model, the extended band stems from slip-induced deactivation of dislocation sources, followed by consequent generation of new sources on adjacent planes, leading to rapid band thickening. Our findings provide insights into atomic-scale collective dislocation motion and microscopic deformation instability in advanced structural materials.

Science & Technology - Other Topics↗
DOE OSTI2024

Eliminating chemo-mechanical degradation of lithium solid-state battery cathodes during >4.5 V cycling using amorphous Nb2O5 coatings

Abstract Lithium solid-state batteries offer improved safety and energy density. However, the limited stability of solid electrolytes (SEs), as well as irreversible structural and chemical changes in the cathode active material, can result in inferior electrochemical performance, particularly during high-voltage cycling (>4.3 V vs Li/Li + ). Therefore, new materials and strategies are needed to stabilize the cathode/SE interface and preserve the cathode material structure during high-voltage cycling. Here, we introduce a thin (~5 nm) conformal coating of amorphous Nb 2 O 5 on single-crystal LiNi 0.5 Mn 0.3 Co 0.2 O 2 cathode particles using rotary-bed atomic layer deposition (ALD). Full cells with Li 4 Ti 5 O 12 anodes and Nb 2 O 5 -coated cathodes demonstrate a higher initial Coulombic efficiency of 91.6% ± 0.5% compared to 82.2% ± 0.3% for the uncoated samples, along with improved rate capability (10x higher accessible capacity at 2C rate) and remarkable capacity retention during extended cycling (99.4% after 500 cycles at 4.7 V vs Li/Li + ). These improvements are associated with reduced cell polarization and interfacial impedance for the coated samples. Post-cycling electron microscopy analysis reveals that the Nb 2 O 5 coating remains intact and prevents the formation of spinel and rock-salt phases, which eliminates intra-particle cracking of the single-crystal cathode material. These findings demonstrate a potential pathway towards stable and high-performance solid-state batteries during high-voltage operation.

Science & Technology - Other Topics↗