Search NASA⌕ Search

SEARCH · Search NASA

Results for “density estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Remote sensing of the ionospheric F layer by use of O I 6300-A and O I 1356-A observations

The possibility of using airglow techniques for estimating the electron density and height of the F layer is studied on the basis of a simple relationship between the height of the F2 peak and the column emission rates of the O I 6300 A and O I 1356 A lines. The feasibility of this approach is confirmed by a numerical calculation of F2 peak heights and electron densities from simultaneous measurements of O I 6300 A and O I 1356 A obtained with earth-facing photometers carried by the Ogo 4 satellite. Good agreement is established with the F2 peak heights estimates from top-side and bottom-side ionospheric sounding.

Chandra, S.↗

The role of isotope mass on neutral fueling and density pedestal structure in the DIII-D tokamak

Abstract Experimental measurements on DIII-D of hydrogen neutral penetration lengths ( λ n 0 ) on the high field side (HFS) are longer by a factor of 2 than for deuterium consistent with the thermal velocity ratio for neutrals at the same temperature ( v t h H / v t h D = 2 ) . This ratio is constant for both low and high pedestal electron density. At low pedestal density ( n e ∼ 4 × 10 19 m − 3 ) , the neutral penetration length is greater than the density pedestal width for both isotopes, and the additional 40% increase of neutral penetration in hydrogen widens the pedestal by the same amount. As the density pedestal height increases ( n e ∼ 6 × 10 19 m − 3 ) , the neutral penetration lengths drop below the density pedestal widths for both isotopes, and the increased penetration of hydrogen has no increased effect on the pedestal width compared to deuterium. Extrapolating to future reactor-relevant high electron density pedestals, the isotope-mass change in neutral fueling on the HFS from the deepest neutral penetration of hydrogen, to the shortest neutral penetration of tritium will be negligible (0.2–0.4 cm) in comparison to estimates of the density pedestal width (6–8.5 cm).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Kinetic equation approach to pair production by a time-dependent electric field

We investigate the quantum kinetic approach to pair production from vacuum by a time-dependent electric field. Equivalence between this approach and the more familiar S-matrix approach is explicitly established for both scalar and fermion cases. For the particular case of a constant electric field, the exact solution for kinetic equations is provided and the accuracy of low-density approximation is estimated.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Multi-Wavelength Based Optical Density Sensor for Autonomous Monitoring of Microalgae

A multi-wavelength based optical density sensor unit was designed, developed, and evaluated to monitor microalgae growth in real time. The system consisted of five main components including (1) laser diode modules as light sources (2) photodiodes as detectors, (3) driver circuit, (4) flow cell and (5) sensor housing temperature controller. The sensor unit was designed to be integrated into any microalgae culture system for both real time and non-real time optical density measurements and algae growth monitoring applications. It was shown that the sensor unit was capable of monitoring the dynamics and physiological changes of the microalgae culture in real-time. Algae biomass concentration was accurately estimated with optical density measurements at 650, 685 and 780 nm wavelengths used by the sensor unit. The sensor unit was able to monitor cell concentration as high as 1.05 g L -1 (1.51x10 8 cells mL -1 ) during the culture growth without any sample preparation for the measurements. Since high cell concentrations do not need to be diluted using the sensor unit, the system has the potential to be used in industrial microalgae cultivation systems for real time monitoring and control applications that can lead to improved resource use efficiency.

09 BIOMASS FUELS↗

STRAIGHTENING THE DENSITY-DISPLACEMENT RELATION WITH A LOGARITHMIC TRANSFORM

We investigate the use of a logarithmic density variable in estimating the Lagrangian displacement field motivated by the success of a logarithmic transformation in restoring information to the matter power spectrum. The logarithmic relation is an extension of the linear relation, motivated by the continuity equation, in which the density field is assumed to be proportional to the divergence of the displacement field; we compare the linear and logarithmic relations by measuring both of these fields directly in a cosmological N-body simulation. The relative success of the logarithmic and linear relations depends on the scale at which the density field is smoothed. Thus we explore several ways of measuring the density field, including Cloud-In-Cell smoothing, adaptive smoothing, and the (scale-independent) Delaunay tessellation, and we use both a Fourier-space and a geometrical tessellation approach to measuring the divergence. We find that the relation between the divergence of the displacement field and the density is significantly tighter and straighter with a logarithmic density variable, especially at low redshifts and for very small ({approx}2 h{sup -1} Mpc) smoothing scales. We find that the grid-based methods are more reliable than the tessellation-based method of calculating both the density and the divergence fields, though in both cases the logarithmic relation works better in the appropriate regime, which corresponds to nonlinear scales for the grid-based methods and low densities for the tessellation-based method.

79 ASTRONOMY AND ASTROPHYSICS↗

The KPD survey for galactic plane ultraviolet-excess objects Space densities of white dwarfs and subdwarfs

A survey for ultraviolet-excess objects has been performed for over about 1000 sq deg of the Galactic plane. Photographic blue and ultraviolet plates were obtained to select ultraviolet-excess candidates, and spectroscopic observations were used to determine the nature of those objects. Over 70 white dwarfs and subdwarfs were identified from the survey plates, and these objects were analyzed statistically to determine scale heights and space densities. The sample was complete to B = 15.3 mag, with the space density of white dwarfs for Mv of less than 12.25 equal to 0.72 + or 0.25/1000 cu pc, slightly higher than that from the Palomar-Green survey. The average absolute magnitude determined for both the subdwarf O and the subdwarf B stars was considerably fainter than previous determinations, while the scale height for the subdwarfs was lower than earlier suggested values. The space density for the subdwarf O stars is about 7 x 10 to the -7th/cu pc, while the value for the subdwarf B stars is about 2 x 10 to the -6th/cu pc, both values considerably higher than previous estimates. The space densities can be used to place evolutionary constraints on these objects.

Downes, R. A.↗

An overview of the Evaluation of Oxygen Interaction with Materials-third phase (EOIM-3) experiment: Space Shuttle Mission 46

The interaction of the atomic oxygen (AO) component of the low earth orbit (LEO) environment with spacecraft materials has been the subject of several flight experiments over the past 11 years. The effect of AO interactions with materials has been shown to be significant for long-lived spacecraft such as Space Station Freedom and has resulted in materials changes for externally exposed surfaces. The data obtained from previous flight experiments, augmented by limited ground-based evaluation, have been used to evaluate hardware performance and select materials. Questions pertaining to the accuracy of this data base remain, resulting from the use of long-term ambient density models to estimate the O-atom fluxes and fluences needed to calculate materials reactivity in short-term flight experiments. The EOIM-3 flight experiment was designed to produce benchmark AO reactivity data and was carried out during STS-46. Ambient density measurements were made with a quadrupole mass spectrometer which was calibrated for AO measurements in a unique ground-based test facility. The combination of these data with the predictions of ambient density models allows an assessment of the accuracy of measured reaction rates on a wide variety of materials, many of which had never been tested in LEO before. The mass spectrometer is also used to obtain a better definition of the local neutral and plasma environments resulting from interaction of the ambient atmosphere with various spacecraft surfaces. In addition, the EOIM-3 experiment was designed to produce information on the effects of temperature, mechanical stress, and solar exposure on the AO reactivity of a wide range of materials. An overview of the EOIM-3 methods and results are presented.

Leger, Lubert J.↗

Performance of the IRI-2007 Model for Topside Ion Density and Composition Profiles During the 23/24 Solar Minimum

The recent solar minimum between cycles 23 and 24 was unusually extended and deep, resulting in an ionosphere that is significantly different from that expected based on previous solar minima. The ion density and composition estimates from the Communication/Navigation Outage Forecast System (C/NOFS) satellite are used to evaluate the performance of the IRI-2007 model between 400 and 850 kIn altitude in equatorial regions. The current model is shown to typically overestimate the expected topside density of 0+ and underestimate the density of H+ during 2008 and 2009. The overestimation of ion density by IRI-2007 is found to vary with local time and longitude.

Klenzing, J. H.↗

Integrated Flush Air Data Sensing System Modeling for Planetary Entry Guidance with Direct Force Control

Flush air data sensing (FADS) systems have been previously used at both Earth and Mars to provide onboard estimates of angle of attack, sideslip angle, and dynamic pressure. However, these FADS data were often not used in an in-the-loop sense to inform the onboard guidance and control systems. A method to integrate FADS-derived density and wind estimates with a numerical predictor-corrector guidance algorithm is presented. The method is demonstrated in a high-fidelity simulation of a human-scale Mars entry vehicle that utilizes a hypersonic inflatable aerodynamic decelerator (HIAD) with direct force control. Effects on guidance commands and state uncertainties both with and without FADS system modeling are presented and discussed.

Lugo, Rafael A.↗

Harmonized wood density data for Central Amazon species in the BIONTE experimental area in Manaus, Brazil

BIONTE (BIOmass and NuTrient Experiment) is a selective logging experiment established at the Experimental Station of Tropical Forestry (EEST, aka “ZF2”) field research station in the mid 1980s in the central Amazon (Higuchi et al. 1997, Amaral et al. 2019). The main data related to BIONTE are available as a separate dataset (Lima et al. 2022). Only species identified within the BIONTE plots were included in this dataset. Wood density, expressed in g cm-3, was collated from multiple sources that were integrated to compose the wood density for BIONTE. The starting point used was wood density data available from Chave et al. (2006), which was then adapted by Marra et al. (2016) and Marra et al. (2018). We also included data collected and synthesized by Ramírez-Méndez (2018) and Gimenez et al.(2021), who combined local estimates of wood density at the site with other sources collected in the Central Amazon. Data are included in .csv files, while BIONTE_WD_headers.txt provides descriptions of data file headers.

54 ENVIRONMENTAL SCIENCES↗

Model-based prognostics for batteries which estimates useful life and uses a probability density function

This invention develops a mathematical model to describe battery behavior during individual discharge cycles as well as over its cycle life. The basis for the form of the model has been linked to the internal processes of the battery and validated using experimental data. Effects of temperature and load current have also been incorporated into the model. Subsequently, the model has been used in a Particle Filtering framework to make predictions of remaining useful life for individual discharge cycles as well as for cycle life. The prediction performance was found to be satisfactory as measured by performance metrics customized for prognostics for a sample case. The work presented here provides initial steps towards a comprehensive health management solution for energy storage devices.

Saha, Bhaskar↗

Sample Results From Tank 48H Samples HTF-48-14-158, -159, -169, and -170

Savannah River National Laboratory (SRNL) analyzed samples from Tank 48H in support of determining the cause for the unusually high dose rates at the sampling points for this tank. A set of two samples was taken from the quiescent tank, and two additional samples were taken after the contents of the tank were mixed. The results of the analyses of all the samples show that the contents of the tank have changed very little since the analysis of the previous sample in 2012. The solids are almost exclusively composed of tetraphenylborate (TPB) salts, and there is no indication of acceleration in the TPB decomposition. The filtrate composition shows a moderate increase in salt concentration and density, which is attributable to the addition of NaOH for the purposes of corrosion control. An older modeling simulation of the TPB degradation was updated, and the supernate results from a 2012 sample were run in the model. This result was compared to the results from the 2014 recent sample results reported in this document. The model indicates there is no change in the TPB degradation from 2012 to 2014. SRNL measured the buoyancy of the TPB solids in Tank 48H simulant solutions. It was determined that a solution of density 1.279 g/mL (~6.5M sodium) was capable of indefinitely suspending the TPB solids evenly throughout the solution. A solution of density 1.296 g/mL (~7M sodium) caused a significant fraction of the solids to float on the solution surface. As the experiments could not include the effect of additional buoyancy elements such as benzene or hydrogen generation, the buoyancy measurements provide an upper bound estimate of the density in Tank 48H required to float the solids.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effects of primordial fluctuations on the abundances of light elements

Some of the effects of primordial inhomogeneities on the production of H-2, He-3, and Li-7 are investigated. For the most part, temperature fluctuations have only small effects on the abundances. The density fluctuations are modeled by a unimodal distribution so that the Universe is characterized by the mean density and the relative amplitude of the density variations. It has been found that the constraint which H-2 production imposes on the mean mass density is eased somewhat by allowing for density inhomogeneities. However, unless the composition of the interstellar matter is atypical of most of the matter in the Universe, the mass density will be at least a factor of 3 below the critical density. For reasonable estimates of the pregalactic abundances, sufficient He-3 and Li-7 cannot be produced in the same model universe. Production of both Li-7 and H-2 requires large-amplitude primordial fluctuations, while sufficient He-3 and H-2 can be formed in very low-density, fairly homogeneous universes.

Epstein, R. I.↗

CONSTRAINTS ON THE PHYSICAL PROPERTIES OF MAIN BELT COMET P/2013 R3 FROM ITS BREAKUP EVENT

Jewitt et al. recently reported that main belt comet P/2013 R3 experienced a breakup, probably due to rotational disruption, with its components separating on mutually hyperbolic orbits. We propose a technique for constraining physical properties of the proto-body, especially the initial spin period and cohesive strength, as a function of the body's estimated size and density. The breakup conditions are developed by combining mutual orbit dynamics of the smaller components and the failure condition of the proto-body. Given a proto-body with a bulk density ranging from 1000 kg m{sup –3} to 1500 kg m{sup –3} (a typical range of the bulk density of C-type asteroids), we obtain possible values of the cohesive strength (40-210 Pa) and the initial spin state (0.48-1.9 hr). From this result, we conclude that although the proto-body could have been a rubble pile, it was likely spinning beyond its gravitational binding limit and would have needed cohesive strength to hold itself together. Additional observations of P/2013 R3 will enable stronger constraints on this event, and the present technique will be able to give more precise estimates of its internal structure.

79 ASTRONOMY AND ASTROPHYSICS↗

PROBABILISTIC MODEL OF BEAM–PLASMA INTERACTION IN RANDOMLY INHOMOGENEOUS PLASMA

We propose a new model that describes beam–plasma interaction in the presence of random density fluctuations with a known probability distribution. We use the property that, for the given frequency, the probability distribution of the density fluctuations uniquely determines the probability distribution of the phase velocity of waves. We present the system as discrete and consisting of small, equal spatial intervals with a linear density profile. This approach allows one to estimate variations in wave energy density and particle velocity, depending on the density gradient on any small spatial interval. Because the characteristic time for the evolution of the electron distribution function and the wave energy is much longer than the time required for a single wave–particle resonant interaction over a small interval, we determine the description for the relaxation process in terms of averaged quantities. We derive a system of equations, similar to the quasi-linear approximation, with the conventional velocity diffusion coefficient D and the wave growth rate γ replaced by the average in phase space, by making use of the probability distribution for phase velocities and by assuming that the interaction in each interval is independent of previous interactions. Functions D and γ are completely determined by the distribution function for the amplitudes of the fluctuations. For the Gaussian distribution of the density fluctuations, we show that the relaxation process is determined by the ratio of beam velocity to plasma thermal velocity, the dispersion of the fluctuations, and the width of the beam in the velocity space.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗