Search NASA⌕ Search

SEARCH · Search NASA

Results for “optical efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Single-Arm Double-Mode Double-Order Planar Waveguide Interferometric Sensor

We have met the goals stated in section one for the project. We have demonstrated the feasibility of a single-arm double-mode double-order waveguide interferometer as a cost efficient alternative to an optical chemical sensor. Experimental prototype was built as a dye-doped polymer waveguide with propagating modes of orders <<0>> and <<1>> of the same TM polarization. The prototype demonstrated sensitivity to ammonia of the order of 200 ppm per one full oscillation of the signal. Sensor based on polyimide doped with BCP can operate at elevated temperature up to 150 C. Upon the future funding, we are planning to optimize the light source, material and the design in order to achieve sensitivity of the order of 1 ppm per full oscillations.

Sarkisov, Sergey S.↗

Nested Focusing Optics for Compact Neutron Sources

NASA's Marshall Space Flight Center, the Massachusetts Institute of Technology (MIT), and the University of Alabama Huntsville (UAH) have developed novel neutron grazing incidence optics for use with small-scale portable neutron generators. The technology was developed to enable the use of commercially available neutron generators for applications requiring high flux densities, including high performance imaging and analysis. Nested grazing incidence mirror optics, with high collection efficiency, are used to produce divergent, parallel, or convergent neutron beams. Ray tracing simulations of the system (with source-object separation of 10m for 5 meV neutrons) show nearly an order of magnitude neutron flux increase on a 1-mm diameter object. The technology is a result of joint development efforts between NASA and MIT researchers seeking to maximize neutron flux from diffuse sources for imaging and testing applications.

Nabors, Sammy A.↗

Characterization of a Photon Counting Test Bed for Space to Ground Optical Pulse Position Modulation Communications Links

The National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) has developed a laboratory transmitter and receiver prototype of a space to ground optical communications link. The system is meant to emulate future deep space optical communication links, such as the first crewed flight of Orion, in which the transmitted laser is modulated using pulse position modulation and the receiver is capable of detecting single photons. The transmitter prototype consists of a software defined radio, a high extinction ratio electro-optic modulator system, and 1550 nm laser. The receiver is a scalable concept and utilizes a single-pixel array of fiber coupled superconducting nanowire single photon detectors. The transmit and receive waveforms follow the Consultative Committee for Space Data Systems (CCSDS) Optical Communications High Photon Efficiency Standard. This paper describes the transmitter and receiver prototypes as well as the system test configuration. System level tests results are presented and compared to predictions from software simulations.

Nappier, Jennifer M.↗

Nulling interferometers: the importance of systematic errors and the X-Array configuration

The nulling interferometers proposed for planet detection are arrays of collector telescopes whose amplitudes and phases are carefully controlled to generate a null response at the star. Perturbations in the amplitude and phase response of the instrument lead to time-dependent fluctuations in the stellar leakage that can mimic a planet signal. Understanding these non-linear systematic errors is important, since they drive most of the instrument requirements for missions such as the Terrestrial Planet Finder and Darwin. We show that 'amplitude-phase' errors are the dominant source of instrument noise. They are unaffected by the technique of phase chopping, increase rapidly at short wavelengths, are largely independent of the size and transmission efficiency of the collector optics, and depend only weakly on the nulling configuration and distance to the target system. Detection of an Earth around a G-type star like the sun requires -1.5 nm of path control and -0.1% control of the amplitude, integrated over all frequencies, including DC. This paper also introduces the X-Array - a new nulling configuration with 4 collectors and a central combiner arranged in an X pattern. This has a number of advantages over the standard dual Bracewell layout, and over other configurations that have been proposed

Dubovitsky, Serge↗

Experimental verification of a theoretical model of an active cladding optical fiber fluorosensor

Experiments were conducted to verify a theoretical model on the injection efficiency of sources in the cladding of an optical fiber. The theoretical results predicted an increase in the injection efficiency for higher differences in refractive indices between the core and cladding. The experimental apparatus used consisted of a glass rod 50 cm long, coated at one end with a thin film of fluorescent substance. The fluorescent substance was excited with side illumination, perpendicular to the rod axis, using a 476 nm Argon-ion laser. Part of the excited fluorescence was injected into the core and guided to a detector. The signal was measured for several different cladding refractive indices. The cladding consisted of sugar dissolved in water and the refractive index was changed by varying the sugar concentration in the solution. The results indicate that the power injected into the rod, due to evanescent wave injection, increases with the difference in refractive index which is in qualitative agreement with theory.

Albin, Sacharia↗

Ultranarrow-waveguide AlGaAs/GaAs/InGaAs lasers

We have designed, fabricated and studied ultranarrow-waveguide heterostructure lasers emitting in the spectral range 1000 – 1100 nm. The lasers have been characterised by current – voltage, light – current, far-field intensity distribution and internal optical loss measurements. The ultranarrow-waveguide lasers have been shown to have a threshold current density of ∼75 A cm{sup −2}, internal quantum efficiency near 100 % and internal optical loss near the lasing threshold under 1 cm{sup −1}, which corresponds to the level of standard heterostructures. We have demonstrated the possibility of obtaining up to 5 W of output power in continuous mode and up to 30 W in pulsed mode, with a beam convergence (FWHM) of 17.8°. The slope of the internal optical loss as a function of pump current for the ultranarrow-waveguide lasers can be markedly lower than that in lasers with a standard design, but internal quantum efficiency drops to 40 % with increasing pump current. The use of barrier layers in ultranarrow-waveguide lasers makes it possible to substantially reduce the drop in internal quantum efficiency. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Observation of intravalley phonon scattering of 2s excitons in MoSe 2 and WSe 2 monolayers

Abstract We present a high-resolution resonance Raman study of hBN encapsulated MoSe 2 and WSe 2 monolayers at 4 K using excitation energies from 1.6 eV to 2.25 eV. We report resonances with the WSe 2 A2s and MoSe 2 A2s and B2s excited Rydberg states despite their low oscillator strength. When resonant with the 2s states we identify new Raman peaks which are associated with intravalley scattering between different Rydberg states via optical phonons. By calibrating the Raman scattering efficiency and separately constraining the electric dipole matrix elements, we reveal that the scattering rates for k = 0 optical phonons are comparable for both 1s and 2s states despite differences in the envelope functions. We also observe multiple new dispersive Raman peaks including a peak at the WSe 2 A2s resonance that demonstrates non-linear dispersion and peak-splitting behavior that suggests the dispersion relations for dark excitonic states at energies near the 2s state are extremely complex.

Materials Science↗

A hole accelerator for InGaN/GaN light-emitting diodes

The quantum efficiency of InGaN/GaN light-emitting diodes (LEDs) has been significantly limited by the insufficient hole injection, and this is caused by the inefficient p-type doping and the low hole mobility. The low hole mobility makes the holes less energetic, which hinders the hole injection into the multiple quantum wells (MQWs) especially when a p-type AlGaN electron blocking layer (EBL) is adopted. In this work, we report a hole accelerator to accelerate the holes so that the holes can obtain adequate kinetic energy, travel across the p-type EBL, and then enter the MQWs more efficiently and smoothly. In addition to the numerical study, the effectiveness of the hole accelerator is experimentally shown through achieving improved optical output power and reduced efficiency droop for the proposed InGaN/GaN LED.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A fast Huygens sweeping method for capturing paraxial multi-color optical self-focusing in nematic liquid crystals

We propose a numerically efficient algorithm for simulating the multi-color optical self-focusing phenomena in nematic liquid crystals. The propagation of the nematicon is modeled by a parabolic wave equation coupled with a nonlinear elliptic partial differential equation governing the angle between the crystal and the direction of propagation. Numerically, the paraxial parabolic wave equation is solved by a fast Huygens sweeping method, while the nonlinear elliptic PDE is handled by the alternating direction explicit (ADE) method. The overall algorithm is shown to be numerically efficient for computing high frequency beam propagations. - Highlights: • A simple strategy can already improve the fast Huygens sweeping method for high frequency asymptotic solutions. • The Alternating Direction Explicit method can significant improve the computational efficiency. • Numerical solutions match the Fredericks transition.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Pulsed semiconductor lasers with higher optical strength of cavity output mirrors

Asymmetric heterostructures with an ultrathick waveguide based on an AlGaAs/GaAs alloy system that allow lasing at a wavelength of 905 nm have been developed and fabricated by hydride metalorganic vapor-phase epitaxy. The internal optical loss and internal quantum efficiency of semiconductor lasers based on such structures were 0.7 cm{sup -1} and 97%, respectively. It is shown that the highest output optical power of laser diodes with antireflecting (SiO{sub 2}) and reflecting (Si/SiO{sub 2}) coatings deposited on untreated Fabry-Perot cavity facets obtained by cleaving in an oxygen atmosphere reached 67 W in the pulsed mode and is limited by mirror damage. Treatment of Fabry-Perot cavity facets by etching in argon plasma and the formation of coatings with passivating and oxygen-blocking GaN and Si{sub 3}N{sub 4} layers allowed an increase in the maximum output optical power to 120 W. Mirror damage was not observed at the attained output optical power.

36 MATERIALS SCIENCE↗

Green-emitting cubic GaN/In 0.16 Ga 0.84 N/GaN quantum well with 32% internal quantum efficiency at room temperature

Structural and optical properties of a green-emitting cubic (i.e., zinc blende) GaN/In 0.16 Ga 0.84 N/GaN single quantum well structure are reported. The active layer is grown on a phase-pure (i.e., 100%) cubic GaN enabled on a 1 × 1 cm 2 U-grooved silicon (100) through aspect ratio phase trapping. Energy dispersive x-ray spectroscopy combined with room temperature cathodoluminescence reveals 522 nm green light emission at room temperature with only 16.0% ± 1.6% of indium content, which is ~30% less than the amount of indium needed in a traditional green-emitting hexagonal (i.e., wurtzite) well. Temperature-dependent behavior of the green emission, such as activation energy, s-shaped peak energy shift, and linewidth, is reported. Cathodoluminescence at 8 and 300 K reveals an internal quantum efficiency of 32.0% ± 0.6%, which is higher than any reported value for cubic wells. Altogether, phase-pure cubic active layers on phase transition cubic GaN are shown to be promising for green and longer wavelength emitters.

42 ENGINEERING↗

Heterogeneous metasurface for high temperature selective emission

We demonstrate selective emission from a heterogeneous metasurface that can survive repeated temperature cycling at 1300 K. Simulations, fabrication, and characterization were performed for a cross-over-a-backplane metasurface consisting of platinum and alumina layers on a sapphire substrate. The structure was stabilized for high temperature operation by an encapsulating alumina layer. The geometry was optimized for integration into a thermophotovoltaic (TPV) system, and was designed to have its emissivity matched to the external quantum efficiency spectrum of 0.6 eV InGaAs TPV material. We present spectral measurements of the metasurface that result in a predicted 22% optical-to-electrical power conversion efficiency in a simplified model at 1300 K. Furthermore, this broadly adaptable selective emitter design can be easily integrated into full-scale TPV systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Brillouin Sensing with PCA, and PCA-Based Neural Networks for Efficient Temperature Monitoring

This work explores peak estimation techniques in Brillouin Optical Time Domain Analysis (BOTDA), emphasizing both accuracy and efficiency. Euclidean distance measurement method is applied to principal components derived from Brillouin Gain Spectrum data. It offers a major speed advantage being 180 170 times faster than traditional curve fitting methods such as Lorentzian curve fitting, while maintaining similar accuracy. Additionally, a PCA- based neural network model shows significant reduction of peak estimation time compared to Lorentzian fitting. Results show Brillouin frequency shift errors lie under 0.75 MHz in both Euclidean distance-based and neural network-based methods, both of which utilize PCA components. For large data sets and long length fibers, PCA- assisted neural network for peak estimation would be an efficient solution.

Distributed optical fiber sensing↗

Optical remote measurement of toxic gases

Enactment of the Clean Air Act Amendments (CAAA) of 1990 has resulted in increased ambient air monitoring needs for industry, some of which may be met efficiently using open-path optical remote sensing techniques. These techniques include Fourier transform spectroscopy, differential optical absorption spectroscopy, laser long-path absorption, differential absorption lidar, and gas cell correlation spectroscopy. With this regulatory impetus, it is an opportune time to consider applying these technologies to the remote and/or path-averaged measurement and monitoring of toxic gases covered by the CAAA. This article reviews the optical remote sensing technology and literature for that application.

Review↗

High-temperature optically activated GaAs power switching for aircraft digital electronic control

Gallium arsenide high-temperature devices were fabricated and assembled into an optically activated pulse-width-modulated power control for a torque motor typical of the kinds used in jet engine actuators. A bipolar heterojunction phototransistor with gallium aluminum arsenide emitter/window, a gallium arsenide junction field-effect power transistor and a gallium arsenide transient protection diode were designed and fabricated. A high-temperature fiber optic/phototransistor coupling scheme was implemented. The devices assembled into the demonstrator were successfully tested at 250 C, proving the feasibility of actuator-located switching of control power using optical signals transmitted by fibers. Assessments of the efficiency and technical merits were made for extension of this high-temperature technology to local conversion of optical power to electrical power and its control at levels useful for driving actuators. Optical power sources included in the comparisons were an infrared light-emitting diode, an injection laser diode, tungsten-halogen lamps and arc lamps. Optical-to-electrical power conversion was limited to photovoltaics located at the actuator. Impedance matching of the photovoltaic array to the load was considered over the full temperature range, -55 C to 260 C. Loss of photovoltaic efficiency at higher temperatures was taken into account. Serious losses in efficiency are: (1) in the optical source and the cooling which they may require in the assumed 125 C ambient, (2) in the decreased conversion efficiency of the gallium arsenide photovoltaic at 260 C, and (3) in impedance matching. Practical systems require improvements in these areas.

Berak, J. M.↗

Initial Characterization of Optical Communications with Disruption-Tolerant Network Protocols

Disruption-tolerant networks (DTNs) are groups of network assets connected with a suite of communication protocol technologies designed to mitigate the effects of link delay and disruption. Application of DTN protocols to diverse groups of network resources in multiple sub-networks results in an overlay network-of-networks with autonomous data routing capability. In space environments where delay or disruption is expected, performance of this type of architecture (such as an interplanetary internet) can increase with the inclusion of new communications mediums and techniques. Space-based optical communication links are therefore an excellent building block of space DTN architectures. When compared to traditional radio frequency (RF) communications, optical systems can provide extremely power-efficient and high bandwidth links bridging sub-networks. Because optical links are more susceptible to link disruption and experience the same light-speed delays as RF, optical-enabled DTN architectures can lessen potential drawbacks and maintain the benefits of autonomous optical communications over deep space distances. These environment-driven expectations - link delay and interruption, along with asymmetric data rates - are the purpose of the proof-of-concept experiment outlined herein. In recognizing the potential of these two technologies, we report an initial experiment and characterization of the performance of a DTN-enabled space optical link. The experiment design employs a point-to-point free-space optical link configured to have asymmetric bandwidth. This link connects two networked systems running a DTN protocol implementation designed and written at JPL for use on spacecraft, and further configured for higher bandwidth performance. Comparing baseline data transmission metrics with and without periodic optical link interruptions, the experiment confirmed the DTN protocols' ability to handle real-world unexpected link outages while maintaining capability of reliably delivering data at relatively high rates. Finally, performance characterizations from this data suggest performance optimizations to configuration and protocols for future optical-specific DTN space link scenarios.

Space networking↗

Testing of A Photon-Counting Optical Ground Receiver With Emulated Space-to-Ground Link Effects

The National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) developed and previously characterized a photon-counting optical ground receiver system. The receiver is compliant with the Consultative Committee for Space Data Systems (CCSDS) Optical Communications Coding and Synchronization High Photon Efficiency (HPE) Standard. The standard will be used on the Optical Artemis-2 Orion (O2O) communications demonstration and the Deep Space Optical Communication (DSOC) project aboard the Psyche spacecraft. The receiver system consists of a fiber interconnect, up to sixteen superconducting nanowire single-photon detectors (SNSPDs), and a field programmable gate array (FPGA) based receive modem. Previously, the receiver system architecture was described and test results without emulated link effects were presented. SNSPD device properties, which impact detection jitter and time delay, can limit the receiver dynamic range, especially when operating with varying flux rates (>10 dB) between detectors. Codeword error-rate curves with and without simulated clock drifts attributed to Doppler shift and space transmitter clock differences are presented. Results with ±66 ppm clock differences show minimal performance impact (<0.2 dB). Test results show that the receiver dynamic range (>28 dB) is limited by changing SNSPD detection delays at high photon flux rates.

optical communications↗

Testing of A Photon-Counting Optical Ground Receiver With Emulated Space-to-Ground Link Effects

The National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) developed and previously characterized a photon-counting optical ground receiver system. The receiver is compliant with the Consultative Committee for Space Data Systems (CCSDS) Optical Communications Coding and Synchronization High Photon Efficiency (HPE) Standard. The standard will be used on the Optical Artemis-2 Orion (O2O) communications demonstration and the Deep Space Optical Communication (DSOC) project aboard the Psyche spacecraft. The receiver system consists of a fiber interconnect, up to sixteen superconducting nanowire single-photon detectors (SNSPDs), and a field programmable gate array (FPGA) based receive modem. Previously, the receiver system architecture was described and test results without emulated link effects were presented. SNSPD device properties, which impact detection jitter and time delay, can limit the receiver dynamic range, especially when operating with varying flux rates (>10 dB) between detectors. Codeword error-rate curves with and without simulated clock drifts attributed to Doppler shift and space transmitter clock differences are presented. Results with ±66 ppm clock differences show minimal performance impact (<0.2 dB). Test results show that the receiver dynamic range (>28 dB) is limited by changing SNSPD detection delays at high photon flux rates.

optical communications↗