Search NASA⌕ Search

SEARCH · Search NASA

Results for “subsurface flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Evaluating the Importance of Barometric Pumping for Subsurface Gas Transport Near an Underground Nuclear Test Site

Core Ideas Gas transport modeling can estimate ground surface breakthrough after an underground nuclear explosion. Comparison tracer‐injection experimental and model results reveals parameter sensitivity. Barometric pumping may explain gas breakthrough following an underground nuclear explosion. Amplitude and period of barometric pressure signal are key in controlling breakthrough. An underground nuclear explosion (UNE) generates and distributes radioactive gases that can be transported to the ground surface though preexisting and explosion‐induced fractures over timescales of hours to months. If detected, the presence of short‐lived radionuclides in gas is evidence of a recent UNE. Numerical modeling can provide estimates of surface arrival times that can help inform gas monitoring strategies at suspected foreign test sites. Efforts are underway at historic US UNE sites to better understand subsurface gas‐transport processes following a UNE by geologic characterization of the near‐field damage structures, field‐scale tracer experiments, and subsurface air pressure monitoring. The development of numerical models using historical and experimental datasets from former UNE sites can improve predictions by testing conceptual models, highlighting key processes, and constraining parameter ranges. The models developed in this study represent the U20az site at the Nevada National Security Site where the Barnwell device was expended in December 1989. A two‐phase (water and air), dual‐permeability flow and transport model of the U20az site was built to investigate gas transport processes under recent experimental conditions and following the Barnwell nuclear event. Results indicate that the model can explain both the lack of arrival of radioactive gas tracers in a 2013 field experiment as well as the observed arrival of radioactive gases following the 1989 Barnwell event using barometric pressure records from the respective periods, even when additional advective processes associated with the Barnwell detonation are ignored. The results demonstrate that the character of the barometric records may be a key factor in explaining the differences in transport behavior.

58 GEOSCIENCES↗

Radionuclide Transport Simulations Supporting Proposed Borehole Waste Disposal in Israel

A scientific collaboration between the U.S. and Israel is underway to assess the suitability of a potential site for subsurface radioactive waste disposal in the Negev Desert, Israel. The Negev Desert has several favorable attributes for geologic disposal, including an arid climate, a deep vadose zone, interlayered low-permeability lithologies, and carbonate rocks with high uranium-sorption potential. These features may provide a robust natural barrier to radionuclide migration. Geologic and laboratory characterization data from the Negev Desert are incorporated into multiphase flow and transport models, solved using PFLOTRAN, to aid in site characterization and risk analysis that will support decision-making for waste disposal in an intermediate-depth borehole design. The lithology with the greatest uranium sorption potential at the site is phosphorite. We use modeling to evaluate the ability of this layer to impact uranium transport around a proposed disposal borehole. The current objective of the simulations is focused on characterizing hypothetical leakage from waste canisters and subsequent uranium migration under three infiltration scenarios. Here, we describe a hydrogeologic model based on data from a local exploratory borehole and present results for uranium flow and transport simulations under varying infiltration scenarios. We find that under the current climate conditions, it is likely that uranium will remain in the near-field of the borehole for thousands of years. However, under a hypothesized extreme climate scenario representing an increase in infiltration by a factor of 300x above present-day values, uranium may break through the phosphorite layer and exit the base of the model domain (~200 m above the water table) within 1000 years. Simulation results have direct implications for the planning of nuclear waste disposal in the Negev Desert, and specifically in intermediate-depth boreholes.

58 GEOSCIENCES↗

Migration and Distribution of Natural Organic Matter Injected into Subsurface Systems - 16523

The Savannah River Site (SRS) was one of the major U.S. Department of Energy facilities that produced large amounts of radioactive and hazardous waste during the Cold War era, a legacy of material production for defense purposes. The unlined F-Area seepage basins received approximately 1.8 billion gallons of acidic waste solutions containing low-level radioactivity from numerous isotopes generated by uranium slug and irradiated fuel processing. Sufficient quantities of uranium isotopes, I-129, Tc-99, and tritium migrated into the groundwater, creating an acidic plume with a pH between 3 and 5.5. Humic substances (HS) are complex heterogeneous mixtures of poly-dispersed materials formed by biochemical and chemical reactions during the decay and transformation of plant and microbial remains. They are known for their excellent binding capacity for metals, making them a strong candidate for remediation efforts to reduce the mobility of uranium (VI) in the subsurface. Studies showed that HS are an important ion exchange and metal-complexing ligand, carrying a large number of functional groups with high complexing capacity that can greatly affect the mobility behavior of actinides in natural systems. Hence, it is a potential in situ amendment for treating groundwater contaminated with these constituents. Column experiments were conducted to address the complexities of HS in flow-through porous media representative of the acidic aquifer at the SRS F-Area Seepage Basins. The humate source used, Huma-K, is high in humic and fulvic compounds. The column studies were done using the soil obtained from SRS's FAW-1 core-hole at a depth interval of 60'-70'. A bromide tracer test was performed to obtain the pore volume (PV), variance and Peclet number. The columns were saturated with an artificial groundwater solution prepared to mimic the groundwater at SRS that was pH adjusted to 3.5 and 5 until the effluent pH reached equilibrium. Approximately one (1) PV of 5000 ppm of Huma-K was injected into the columns at 2 ml/min to study the sorption of Huma-K on the sediment. Desorption of Huma-K was studied by injecting approximately four (4) PVs of the pH adjusted artificial groundwater solution. A faster increase in pH was observed in column 1 (saturated with pH 3.5 AGW) compared to column 2 (saturated with pH 5 AGW). After injection of 2 PV of AGW, the pH of the columns reached 6.5 and 7, respectively, for columns 1 and 2. After injecting an additional PV of AGW, the pH remained relatively stable. With an increase in pH from 3.5 to 5.0, the overall retention of HA increased from 461 mg/kg for the column with pH 3.5 to 642 mg/kg for the column with pH 5. This suggests that retention is not due to adsorption alone, but adsorption coupled with precipitation and re-dissolution of Huma-K as it flows through the columns is a possible explanation for greater retention at pH 5. This negates the use of a simple Langmuir isotherm to explain humate behavior in the acidic environment of column 1. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Distribution of uranium and thorium in dolomitic gravel fill and shale saprolite

The objectives of this study were to examine (1) the distribution of U and Th in dolomitic gravel fill and shale saprolite, and (2) the removal of uranium from acidic groundwater by dolomitic gravel through precipitation with amorphous basaluminite at the U.S. DOE Oak Ridge Integrated Field Research Challenge (ORIFRC) field site west of the Oak Ridge Y-12 National Security Complex in East Tennessee. Media reactivity and sustainability are a technical concern with the deployment of any subsurface reactive media. Because the gravel was placed in the subsurface and exposed to contaminated groundwater for over 20 years, it provided a unique opportunity to study the solid and water phase geochemical conditions within the media after this length of exposure. This study illustrates that dolomite gravel can remove U from acidic contaminated groundwater with high levels of Al 3+ , Ca 2+ , NO 3- , and SO 4 2- over the long term. As the groundwater flows through high pH carbonate gravel, U containing amorphous basaluminite precipitates as the pH increases. This is due to an increase in groundwater pH from 3.2 to ~6.5 as it comes in contact with the gravel. Therefore, carbonate gravel could be considered as a possible treatment medium for removal and sequestration ofUand otherpHsensitive metals from acidic contaminated groundwater. Thorium concentrations are also high in the carbonate gravel. Thorium generally shows an inverse relationship with U from the surface down into the deeper saprolite. Barite precipitated in the shallow saprolite directly below the dolomitic gravel from barium present in the acidic contaminated groundwater.

54 ENVIRONMENTAL SCIENCES↗

Viscous Behavior of Clay‐Rich Rocks and Its Role in Focused Fluid Flow

Abstract Focused fluid flow is common in sedimentary basins worldwide, where flow structures often penetrate through sandy reservoir rocks, and clay‐rich caprocks. To better understand the mechanisms forming such structures, the impacts of the viscoelastic deformation and strongly nonlinear porosity‐dependent permeability of clay‐rich materials are assessed from an experimental and numerical modeling perspective. The experimental methods to measure the poroviscoelastic and transport properties of intact and remolded shale have been developed, and the experimental data is used to constrain the numerical simulations. It is demonstrated that viscoelastic deformation combined with nonlinear porosity‐dependent permeability triggers the development of localized flow channels, often imaged as seismic chimneys. The permeability inside a channel increases by several orders of magnitude compared to the background values. In addition, the propagation time scale and the channel size strongly depend on the material properties of the fluid and the rock. The time‐dependent behavior of the clay‐rich rock may play a key role in the long‐term integrity of the subsurface formations.

58 GEOSCIENCES↗

A new mini-triaxial cell for combined high-pressure and high-temperature in situ synchrotron X-ray microtomography experiments up to 400°C and 24 MPa

A new experimental triaxial cell for in situ synchrotron X-ray micro-computed tomography aimed at imaging small samples of (6 mm × 19 mm) at high temperatures (up to 400°C) and pressures (up to 24 MPa confining) is presented. The system has flow-through capabilities, independent axial and radial pressure control, and has been developed and tested at the 8.3.2. beamline at the Advanced Light Source. The characteristics of this new experimental rig are described, along with the challenges, mainly concerning the combination of X-ray transparency with vessel strength at high temperature, and solutions found during the development stage. An experiment involving oil shale pyrolysis under subsurface conditions, highlighting the importance of a device able to operate in this pressure and temperature range, is also introduced. Furthermore, the availability of this cell enables an unprecedented range of experiments in the Earth Sciences, with a special focus on subsurface geothermal processes.

47 OTHER INSTRUMENTATION↗

Determination of Ground Subsidence Around Snow Fences in the Arctic Region

In this study, we analyzed the effects of snow cover changes caused by snow fences (SFs) installed in 2017 in the Alaskan tundra to examine ground subsidence. Digital surface model data obtained through LiDAR-based remote sensing in 2019 and 2022, combined with a field survey in 2021, revealed approximately 0.2 m of ground subsidence around the SF. To investigate the relationship between SF-induced snow cover changes and ground subsidence, geophysical methods, electrical resistivity tomography (ERT) and ground-penetrating radar (GPR), were applied in 2023 to analyze subsurface characteristics. The increased snow cover due to the SF-enhanced insulation, delaying the penetration of winter cold into the subsurface. This delay caused subsurface temperatures to decrease more slowly, melting the upper permafrost and increasing the thickness of the active layer. ERT and GPR surveys well delineated the boundary between the active layer and permafrost, confirming that the increased snow cover thickened the active layer. This thickening led to the melting of pore ice, causing water runoff and ground compaction, which resulted in subsidence. The runoff also formed channels flowing eastward over the SF. This study highlights how changes in snow cover can influence active layer properties, leading to localized environmental changes and ground subsidence.

54 ENVIRONMENTAL SCIENCES↗

Multi‐Layered Systems for Permanent Geologic Storage of CO 2 at the Gigatonne Scale

Abstract The effectiveness of Carbon Capture and Storage (CCS) as an imperative decarbonization technology relies on the sealing capacity of a fine‐grained caprock to permanently store CO 2 deep underground. Uncertainties in assessing the caprock sealing capacity increase with the spatial and temporal scales and may delay CCS deployment at the gigatonne scale. We have developed a computationally efficient transport model to capture the dynamics of basin‐wide upward CO 2 migration in a multi‐layered setting over geological time scales. We find that massive capillary breakthrough and viscous flow of CO 2 , even through pervasively fractured caprocks, are unlikely to occur and compromise the storage security. Potential leakage from the injection reservoir is hampered by repetitive layering of overlying caprocks. This finding agrees with geologic intuition and should be understandable by the public, contributing to the development of climate policies around this technology with increased confidence that CO 2 will be indefinitely contained in the subsurface.

58 GEOSCIENCES↗

Two sides of a fault: Grain-scale analysis of pore pressure control on fault slip

Pore fluid pressure in a fault zone can be altered by natural processes (e.g., mineral dehydration and thermal pressurization) and industrial operations involving subsurface fluid injection and extraction for the development of energy and water resources. However, the effect of pore pressure change on the stability and slip motion of a preexisting geologic fault remains poorly understood; yet, it is critical for the assessment of seismic hazard. In this study, we develop a micromechanical model to investigate the effect of pore pressure on fault slip behavior. The model couples fluid flow on the network of pores with mechanical deformation of the skeleton of solid grains. Pore fluid exerts pressure force onto the grains, the motion of which is solved using the discrete element method. We conceptualize the fault zone as a gouge layer sandwiched between two blocks. We study fault stability in the presence of a pressure discontinuity across the gouge layer and compare it with the case of continuous (homogeneous) pore pressure.We focus on the onset of shear failure in the gouge layer and reproduce conditions where the failure plane is parallel to the fault. We show that when the pressure is discontinuous across the fault, the onset of slip occurs on the side with the higher pore pressure, and that this onset is controlled by the maximum pressure on both sides of the fault. In conclusion, the results shed new light on the use of the effective stress principle and the Coulomb failure criterion in evaluating the stability of a complex fault zone.

58 GEOSCIENCES↗

Effectiveness of an in-situ permeable reactive barrier in removing strontium-90 from groundwater - 15418

An in-situ permeable reactive barrier (PRB) is being used to remove strontium-90 from groundwater along the 100-N Area shoreline at the U.S. Department of Energy Hanford Site in southeastern Washington. The PRB was formed by emplacing apatite, a calcium phosphate mineral, in the subsurface sediments via injection of calcium-citrate and sodium-phosphate solution into the aquifer through a network of vertical wells. The relatively slow biodegradation of citrate allowed sufficient time for the injected solution to disperse in the PRB treatment zone as the free calcium and phosphate combined to form apatite. Substitution of strontium for calcium in the apatite crystal structure is thermodynamically favorable. As groundwater flows through the PRB toward the Columbia River, strontium-90 is sequestered into the apatite crystal matrix. The sequestered strontium-90 undergoes radioactive decay in place within the PRB. Groundwater monitoring wells installed between the PRB and the Columbia River are used to monitor the PRB effectiveness. The concentration of strontium-90 in the monitoring wells following apatite emplacement are compared to the pre-injection concentrations. The performance goal of the PRB is to reduce the concentration of strontium-90 in groundwater down gradient of the PRB by 90 percent, compared to the pre-injection concentrations. Groundwater samples in Fall 2013 show the percent reduction in strontium-90 concentrations ranged from 71 to 98 percent in eleven of the twelve monitoring wells. The data indicate that the PRB is effective in reducing the flux of strontium-90 toward the Columbia River and is thereby instrumental in protection of the Columbia River. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Bioremediation of a Large Chlorinated Solvent Plume, Dover AFB, DE

Bioremediation of a Large Chlorinated Solvent Plume, Dover AFB, DE Aleisa Bloom, (Oak Ridge National Laboratory, Oak Ridge, Tennessee, USA) Robert Lyon (bob.lyon@aecom.com), Laurie Stenberg, and Holly Brown (AECOM, Germantown, Maryland, USA) ABSTRACT: Past disposal practices at Dover Air Force Base (AFB), Delaware, created a large solvent plume called Area 6 (about 1 mile long, 2,000 feet wide, and 345 acres). The main contaminants are PCE, TCE, and their degradation products. The remedy is in-situ accelerated anaerobic bioremediation (AAB). AAB started in 2006 and is focusing on source areas and downgradient plume cores. Direct-push injections occurred in source areas where contamination is typically between 5 and 20 feet below ground surface. Lower concentration dissolved-phased contamination is present downgradient at 35 and 50 feet below ground surface. Here, permanent injection/extraction wells installed in transects perpendicular to the flow of groundwater are used to apply AAB. The AAB substrate is a mix of sodium lactate, emulsified vegetable oil, and nutrients. After eight years, dissolved contaminant mass within the main 80-acre treatment area has been reduced by over 98 percent. This successful application of AAB has stopped the flux of contaminants to the more distal portions of the plume. While more time is needed for effects to be seen in the distal plume, AAB injections will soon cease, and the remedy will transition to natural attenuation. INTRODUCTION Oak Ridge National Laboratory Environmental Science Division (ORNL) and AECOM (formerly URS Corporation) have successfully implemented in situ accelerated anaerobic bioremediation (AAB) to remediate chlorinated solvent contamination in a large, multi-sourced groundwater plume at Dover Air Force Base (AFB). AAB has resulted in significant reductions of dissolved phase chlorinated solvent concentrations. This plume, called Area 6, was originally over 1 mile in length and over 2,000 feet wide (Figure 1). It originated from at least four separate source areas that comingled in the subsurface to form the large plume. The major contaminants of concern (COCs) are tetrachloroethene (PCE), trichloroethene (TCE), and 1,1,1-trichloroethane (1,1,1-TCA), which were historically used for degreasing operations in the maintenance of aircraft and support vehicles. Relatively small areas of elevated PCE, TCE, and 1,1,1-TCA were delineated in the shallow portion of the water table aquifer by direct-push groundwater sampling. Focused direct-push AAB treatment occurred in March 2006 at these source areas (Figure 1). Downgradient of the these areas and deeper in the aquifer, AAB treatment was implemented using rows of extraction/injection wells oriented perpendicular to groundwater flow to create multiple reductive zones across the plume cores, defined as areas where more than 1,000 micrograms per liter (ug/L) total solvent concentrations were present. Initial indications of successful degradation were observed within 6 months of starting injections. FIGURE 1. Dover AFB Area 6 plume. This paper describes the AAB implementation and progress of remediation after 8 years of treatment and periodic groundwater monitoring. SITE LITHOLOGY Contamination at the site is limited to the surficial aquifer, which consists of 35 to 50 feet (ft) (11 to 15 meters [m]) of unconsolidated Pleistocene deposits of the Columbia Formation. The Columbia Formation consists of fine to coarse sand with silt and clay lenses and less common gravel lenses. Silts and silty sands are generally encountered to a depth of 10 to 12 ft (3.05 to 3.65 m) below ground surface (bgs) and grade to medium- and coarse-grained sands to a depth of 35 to 50 ft (11 to 15 m) bgs. There is a clay and silt unit (part of the Calvert Formation) below the surficial aquifer that acts as an aquitard to the downward migration of contaminants. The depth to the water table varies across the site but usually ranges from 8 to 15 ft (2.4 to 4.5 m) bgs in the treatment area. REMEDIAL APPROACH AND OPERATIONS Because the Columbia Aquifer is used as a source of potable water off base, the remedial goal is to restore the aquifer to usable condition, i.e., reduce all chemicals of concern to below drinking water maximum contaminant levels (MCLs). To achieve this goal, AAB was selected as the best remedial alternative to reduce the solvent contamination. Source areas with high solvent concentrations were present in the shallow portion of the aquifer. From the source areas, dissolved solvents migrated downgradient and deeper in the aquifer with the flow of groundwater. In the deeper portion of the aquifer, the individual plumes comingle to form the larger Area 6 Plume, which covers approximately 345 acres. Types of Substrate. Previous AAB pilot tests at Dover AFB used either sodium lactate or emulsified vegetable oil (EVO) as substrates to stimulate microbial growth. The best results were obtained with...

Bloom, Aleisa C↗

Path to Subsurface Closure: When Real and Predicted Data Don't Match, Central Nevada Test Area (CNTA) - 19560

The Central Nevada Test Area, Nevada, was the site of an underground nuclear test in 1968, which resulted in residual contamination at and near the detonation depth of 975 meters (3200 feet). The environmental corrective action strategy for the site was conducted in accordance with the Federal Facility Agreement and Consent Order and all applicable Nevada Division of Environmental Protection (NDEP) policies and regulations. The corrective action strategy initiated in 1999 included developing a conceptual site model, preparing a numerical flow and transport model, calculating contaminant boundaries, negotiating compliance boundaries with NDEP, performing model validation, and monitoring groundwater. This strategy was executed through the Corrective Action Decision Document/Corrective Action Plan phase, when it was determined that the flow and transport model could not be validated because it failed to adequately predict groundwater elevations in the monitoring/validation (MV) wells (MV-1, MV-2, and MV-3) drilled subsequent to the modeling effort. This led to a change in the corrective action strategy that is now designed to validate the compliance boundary through monitoring and institutional controls, rather than relying predominantly on a numerical flow and transport model. This new approach included enhancements to the monitoring well network and additional monitoring to confirm that data were sufficient to proceed to closure. The corrective action activities were completed in 2015, and the Closure Report, which established the long-term postclosure monitoring program, was approved in 2016. The postclosure monitoring program is designed to (1) assess the effectiveness of the compliance boundary by monitoring for the radionuclides of interest and (2) evaluate the effectiveness of monitoring locations within the groundwater flow system by monitoring water elevations to ensure that monitoring wells are located along the potential migration pathways. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Model Data Archive for Manuscript Titled "Evaluation of a Coupled Surface–Subsurface Hydrologic Model Using Dense Water‑Level Sensors in a Mixed Urban–Rural Watershed"

This archive provides scripts, input files, and datasets used for the implementation and evaluation of a fully coupled surface–subsurface hydrologic model in the Neches River Basin, southeast Texas. The study uses the Advanced Terrestrial Simulator (ATS) to simulate coupled surface–subsurface hydrologic processes over a mixed urban–rural watershed and evaluates model performance using a dense network of 136 in situ water-level sensors, nine U.S. Geological Survey (USGS) stream gauges, and SSEBop-derived evapotranspiration estimates during the period October 2014–June 2024. The workflow is implemented primarily in Python 3 using the Watershed Workflow package. The Jupyter notebooks can be executed using open-source software such as Anaconda JupyterLab or Visual Studio Code. Other data files include TXT, CSV, XML, SHP, TIF, NetCDF, HDF5, and ExodusII files, which can be processed using the provided Python scripts. ATS input files are provided in XML format and can be edited using any commonly used text editor. This archive contains: *Scripts and input files used to generate the ATS model setup, including watershed discretization, mesh generation, parameter mapping, and model configuration. *Jupyter notebooks used for preprocessing observational data, evaluating streamflow, water levels, and evapotranspiration, computing performance metrics, and generating the figures presented in the manuscript. *ATS simulation outputs and processed observational datasets, including OneRain and DD6 water-level sensors, USGS streamflow observations, GIS data, and supporting spatial datasets used throughout the study.

Dense water-level sensor network↗

Multiscale Investigation on Biofilm Distribution and Its Impact on Macroscopic Biogeochemical Reaction Rates

Biofilms are critical locations for biogeochemical reactions in the subsurface environment. The occurrence and distribution of biofilms at microscale as well as their impacts on macroscopic biogeochemical reaction rates are still poorly understood. This paper investigated the formation and distributions of biofilms in heterogeneous sediments using multiscale models, and evaluated the effects of biofilm heterogeneity on local and macroscopic biogeochemical reaction rates. Sediment pore structures derived from X-ray computed tomography were used to simulate the microscale flow dynamics and biofilm distribution in the sediment column. The response of biofilm formation and distribution to the variations in hydraulic and chemical properties was first examined. One representative biofilm distribution was then utilized to evaluate its effects on macroscopic reaction rates using nitrate reduction as an example. The results revealed that microorganisms primarily grew on the surfaces of grains and aggregates near preferential flow paths where both electron donor and acceptor were readily accessible, leading to the heterogeneous distribution of biofilms in the sediments. Furthermore, the heterogeneous biofilm distribution decreased the macroscopic rate of biogeochemical reactions as compared with those in homogeneous cases. Operationally considering the heterogeneous biofilm distribution in macroscopic reactive transport models such as using dual porosity domain concept can significantly improve the prediction of biogeochemical reaction rates. Overall, this study provided important insights into the biofilm formation and distribution in soils and sediments as well as their impacts on the macroscopic manifestation of reaction rates.

42 ENGINEERING↗

Water Level Data from Wells PLM1 and PLM6 for the East River Watershed, Colorado

This dataset (Williams et al., 2020) contains the original un-QA/QC-ed water level data for PLM1 and PLM6 and has been obsoleted. The data contained within this dataset is not to be used. Refer to Faybishenko et al., 2022 (DOI: 10.15485/1866836) for the latest QA/QC-ed data available via ESS-DIVE.This data set contains water level data for the PLM1 and PLM6 wells. PLM1 and PLM6 are location identifiers used by the Watershed Function SFA project for two groundwater monitoring wells along an elevation gradient located along the lower montane life zone of a hillslope near the Pumphouse location. These wells used to monitor subsurface water and carbon inventories and fluxes at the East River Watershed, Colorado, USA. Complete metadata information on the PLM1 and PLM6 wells are available in the related data package reference Varadharajan C, et al (2020). https://doi.org/10.15485/1660962.Data are reported in .csv files per well. The latitude and longitude of each location are given in a file called locations.csv. These data are used for determining the seasonally dependent flow of groundwater under the PLM hillslope. The downslope flow of groundwater in combination with data on groundwater chemistry can be used to estimate rates of solute export from the hillslope to the floodplain and river.These data products are part of the Watershed Function Scientific Focus Area collection effort to further scientific understanding of biogeochemical dynamics from genome to watershed scales.

54 ENVIRONMENTAL SCIENCES↗

Salinity and hydraulic retention time induce membrane phospholipid acyl chain remodeling in Halanaerobium congolense WG10 and mixed cultures from hydraulically fractured shale wells

Bacteria remodel their plasma membrane lipidome to maintain key biophysical attributes in response to ecological disturbances. For Halanaerobium and other anaerobic halotolerant taxa that persist in hydraulically fractured deep subsurface shale reservoirs, salinity, and hydraulic retention time (HRT) are important perturbants of cell membrane structure, yet their effects remain poorly understood. Membrane-linked activities underlie in situ microbial growth kinetics and physiologies which drive biogeochemical reactions in engineered subsurface systems. Hence, we used gas chromatography–mass spectrometry (GC–MS) to investigate the effects of salinity and HRT on the phospholipid fatty acid composition of H. congolense WG10 and mixed enrichment cultures from hydraulically fractured shale wells. We also coupled acyl chain remodeling to membrane mechanics by measuring bilayer elasticity using atomic force microscopy (AFM). For these experiments, cultures were grown in a chemostat vessel operated in continuous flow mode under strict anoxia and constant stirring. Our findings show that salinity and HRT induce significant changes in membrane fatty acid chemistry of H. congolense WG10 in distinct and complementary ways. Notably, under nonoptimal salt concentrations (7% and 20% NaCl), H. congolense WG10 elevates the portion of polyunsaturated fatty acids (PUFAs) in its membrane, and this results in an apparent increase in fluidity (homeoviscous adaptation principle) and thickness. Double bond index (DBI) and mean chain length (MCL) were used as proxies for membrane fluidity and thickness, respectively. These results provide new insight into our understanding of how environmental and engineered factors might disrupt the physical and biogeochemical equilibria of fractured shale by inducing physiologically relevant changes in the membrane fatty acid chemistry of persistent microbial taxa. GRAPHICAL ABSTRACT Salinity significantly alters membrane bilayer fluidity and thickness in Halanaerobium congolense WG10.

03 NATURAL GAS↗

Variably Saturated Flow and Multicomponent Biogeochemical Reactive Transport Modeling of a Uranium Bioremediation Field Experiment

Field experiments at a former uranium mill tailings site have identified the potential for stimulating indigenous bacteria to catalyze the conversion of aqueous uranium in the +6 oxidation state to immobile solid-associated uranium in the +4 oxidation state. This effectively removes uranium from solution resulting in groundwater concentrations below actionable standards. Three-dimensional, coupled variably-saturated flow and biogeochemical reactive transport modeling of a 2008 in situ uranium bioremediation field experiment is used to better understand the interplay of transport rates and biogeochemical reaction rates that determine the location and magnitude of key reaction products. A comprehensive reaction network, developed largely through previous 1-D modeling studies, was used to simulate the impacts on uranium behavior of pulsed acetate amendment, seasonal water table variation, spatially-variable physical (hydraulic conductivity, porosity) and geochemical (reactive surface area) material properties. A principal challenge is the mechanistic representation of biologically-mediated terminal electron acceptor process (TEAP) reactions whose products significantly alter geochemical controls on uranium mobility through increases in pH, alkalinity, exchangeable cations, and highly reactive reduction products. In general, these simulations of the 2008 Big Rusty acetate biostimulation field experiment in Rifle, Colorado confirmed previously identified behaviors including (1) initial dominance by iron reducing bacteria that concomitantly reduce aqueous U(VI), (2) sulfate reducing bacteria that become dominant after {approx}30 days and outcompete iron reducers for the acetate electron donor, (3) continuing iron-reducer activity and U(VI) bioreduction during dominantly sulfate reducing conditions, and (4) lower apparent U(VI) removal from groundwater during dominantly sulfate reducing conditions. New knowledge on simultaneously active metal and sulfate reducers has been incorporated into the modeling. In this case, an initially small population of slow growing sulfate reducers is active from the initiation of biostimulation. Three-dimensional, variably saturated flow modeling was used to address impacts of a falling water table during acetate injection. These impacts included a significant reduction in aquifer saturated thickness and isolation of residual reactants and products, as well as unmitigated uranium, in the newly unsaturated vadose zone. High permeability sandy gravel structures resulted in locally high flow rates in the vicinity of injection wells that increased acetate dilution. In downgradient locations, these structures created preferential flow paths for acetate delivery that enhanced local zones of TEAP reactivity and subsidiary reactions. Conversely, smaller transport rates associated with the lower permeability lithofacies (e.g., fine) and vadose zone were shown to limit acetate access and reaction. Once accessed by acetate, however, these same zones limited subsequent acetate dilution and provided longer residence times that resulted in higher concentrations of TEAP products when terminal electron donors and acceptors were not limiting. Finally, facies-based porosity and reactive surface area variations were shown to affect aqueous uranium concentration distributions; however, the ranges were sufficiently small to preserve general trends. Large computer memory and high computational performance were required to simulate the detailed coupled process models for multiple biogeochemical components in highly resolved heterogeneous materials for the 110-day field experiment and 50 days of post-biostimulation behavior. In this case, a highly-scalable subsurface simulator operating on 128 processor cores for 12 hours was used to simulate each realization. An equivalent simulation without parallel processing would have taken 60 days, assuming sufficient memory was available.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Utah FORGE: Well 52-21 Logs and Data: Roosevelt Hot Spring Area

This is a compilation of logs and data from Well 52-21 in the Roosevelt Hot Springs area in Utah. This well is also in the Utah FORGE study area. The file is in a compressed .zip format and there is a data inventory table (Excel spreadsheet) in the root folder that is a guide to the data that is accessible in subfolders.

15 GEOTHERMAL ENERGY↗