Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compressive Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Effect of Grain Boundary Misorientation on Spall Strength in Ta via Shock-Free Simulations with Relatively Few Atoms

A suite of 37 molecular dynamics simulations is conducted at two system sizes to systematically characterize the role of grain boundary (GB) misorientation on spall strength in pure BCC tantalum (Ta). The systems studied consist of bicrystals with a single [110] symmetric tilt grain boundary. Two loading conditions are compared: (i) homogeneous extension under uniaxial strain simulated in this study and (ii) piston/flyer impact of sample, which induces heterogeneous deformation via shockwave propagation along the length of the sample. The piston/flyer impact is taken from the literature and run on the same set of GB misorientation angles using LAMMPS. The major finding here is that both methods result in similar spall strength predictions, but the homogeneous extension method generally requires two to three orders of magnitude fewer atoms and similar reductions in computational costs. Spall strength results systematically overpredict using this method, by about 10% for the dataset three orders of magnitude smaller than piston/flyer simulations, and 5% for the dataset two orders of magnitude smaller. Lastly, the effect of system size and pre-compression magnitude on spall strength is systematically characterized.

36 MATERIALS SCIENCE↗
NASA NTRS1975

On the source of lunar limb compressions

Magnetic-field measurements made on board the Apollo 15 and 16 subsatellites in low-altitude lunar orbit are used to study compressions of the magnetic field over terminator regions when the moon is in the solar wind. These compressional disturbances occur at just in front of the terminator, but only when specific selenographic regions appear at the lunar limb. The occurrence rate, strength, and position of the compression relative to the limb are different for each source region. Where overlaps of limb-compression occurrence statistics and lunar magnetic-field maps exist, the limb-compression occurrence rates have a high degree of correlation with magnetic-field strength. Thus the most probable cause of limb compressions is deflection of the solar wind by the lunar surface magnetic field as the solar wind flows past the lunar terminators.

Russell, C. T.↗
DOE OSTI2020

Water-Dependent Blending of Pectin Films: The Mechanics of Conjoined Biopolymers

Biodegradable pectin polymers have been recommended for a variety of biomedical applications, ranging from the delivery of oral drugs to the repair of injured visceral organs. A promising approach to regulate pectin biostability is the blending of pectin films. To investigate the development of conjoined films, we examined the physical properties of high-methoxyl pectin polymer-polymer (homopolymer) interactions at the adhesive interface. Pectin polymers were tested in glass phase (10–13% w/w water content) and gel phase (38–41% w/w water content). The tensile strength of polymer-polymer adhesion was measured after variable development time and compressive force. Regardless of pretest parameters, the adhesive strength of two glass phase films was negligible. In contrast, adhesion testing of two gel phase films resulted in significant tensile adhesion strength (p < 0.01). Adhesion was also observed between glass phase and gel phase films—likely reflecting the diffusion of water from the gel phase to the glass phase films. In studies of the interaction between two gel phase films, the polymer-polymer adhesive strength increased linearly with increasing compressive force (range 10–80 N) (R 2 = 0.956). In contrast, adhesive strength increased logarithmically with time (range 10–10,000 s) (R 2 = 0.913); most of the adhesive strength was observed within minutes of contact. Fracture mechanics demonstrated that the adhesion of two gel phase films resulted in a conjoined film with distinctive physical properties including increased extensibility, decreased stiffness and a 30% increase in the work of cohesion relative to native polymers (p < 0.01). Scanning electron microscopy of the conjoined films demonstrated cross-grain adhesion at the interface between the adhesive homopolymers. These structural and functional data suggest that blended pectin films have emergent physical properties resulting from the cross-grain intermingling of interfacial pectin chains.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
NASA NTRS1985

Stiffener attachment concepts for graphite-epoxy panels designed for postbuckling strength

Stiffener attachment concepts for suppressing or delaying the onset of the skin-stiffener separation failure mode in graphite-epoxy compression panels designed for postbuckling strength were experimentally studied. The effectiveness of these concepts was evaluated using panels with 16-ply skins and a single centrally-located I-shaped stiffener with both static and cyclic compressive loadings. Analytical results suggest that tailoring the relative thicknesses of the panel skin, stiffener attachment flange, and the stiffener web rotational stiffness can minimize the adverse effects of high interface shear and normal stresses. Interface stress levels may be reduced by tapering the thickness of the stiffener attachment flange and properly selecting the stacking sequences of the skin and stiffener attachment flange laminates.

Dickson, John N.↗
NASA NTRS2023

Damage Tolerance Study of Carbon Fiber/Epoxy Sandwich Structure in Support of the SLS Payload Adapter Fitting (PAF)

This study presents experimental results of impact and subsequent compression after impact (CAI) strength testing of sandwich structure representative of most of the acreage of a Payload Adaptor Fitting (PAF) that has been built at NASA’s Marshall Space Flight Center (MSFC). An instrumented drop weight tower was used to inflict different levels of impact damage to specimens. Load versus deflection of impact curves, visual damage, dent depth, damage as ascertained by thermography and cross-sectional microscopy were evaluated as part of the damage resistance of the structure. Compression After Impact (CAI) was performed to assess damage tolerance. The results show that at the amount of visual damage was highly dependent on whether the peel ply was present on the surface of the structure. The peel ply had some effect on the CAI strength values since the specimens with peel ply showed a 14% higher average CAI strength value. For all specimens tested in this study, CAI versus damage and CAI versus impact energy curves were plotted and it was found that damage size was a good indicator of CAI strength. It is suggested to use a b-basis damage tolerance curve based on damage size as a conservative measure of the load carrying capability of the sandwich structure with impact damage.

T1100/3960↗
NASA NTRS1986

Combined bearing and bypass loading on a graphite/epoxy laminate

A combined experimental and analytical study was conducted to determine the behavior of a graphite/epoxy laminate subjected to combined bearing and bypass loading. Single-fastener quasi-isotropic specimens were loaded at various bearing-bypass ratios until damage was produced at the fastener hole. Damage-onset strengths and damage modes were then analyzed using local hole-boundary stresses calculated by a finite-element analysis. The tension data showed the expected linear interaction for combined bearing and bypass loading with damage developing in the net-section tension mode. However, the compression bearing-bypass strength showed an unexpected interaction involving the bearing mode.

Crews, J. H., Jr.↗
DOE OSTI2023

Mechanical behavior analysis using small-size graphite disc compression testing with digital image correlation methods

The ASTM International Standard Test Method for Tensile Stress-Strain of Carbon and Graphite (ASTM C749) requires dog-bone shaped specimens. Unfortunately, specimen sizes required in ASTM C749 are much too large for irradiation within a test reactor and are incompatible with irradiation capsule volumes, molten salt degradation facilities, or oxidation apparatus. The ASTM International Standard Test Method for Tensile Strength Estimate by Disc Compression of Manufactured Graphite (ASTM D8289) was developed as an alternative that provides a means for testing tensile properties using smaller specimens when geometric constraints are present. However, the important stress–strain relation throughout the test loading history that could be recorded using ASTM C749 is lost by using ASTM D8289 because of the difficulties involved with using traditional strain gauges or extensometers on such a small specimen. In this work, a digital image correlation (DIC) method, which uses a full-field noncontact surface displacement measurement technique, was applied along with the ASTM D8289 splitting tensile test on eight small samples of graphite grade Mersen 2114 to track their deformation during compressive loading. Initial results showed that the DIC technique can measure the surface displacement/strain on these small (Ø6 × 3 mm) graphite specimens with high accuracy and good repeatability, indicating that the DIC technique, combined with the small-disc splitting tensile test in ASTM D8289, can capture the strain evolution in the test. In conclusion, further comparison of measured strains with analytical and numerical simulation results provides additional understanding of the mechanical behaviour of this nuclear graphite material in complex stress states.

36 MATERIALS SCIENCE↗
NASA NTRS2020

Analysis of Open Hole Compression Specimens Using the CompDam Continuum Damage Mechanics Model

This report documents a validation study on the standard Open Hole Compression (OHC) laminate test specimen conducted as part of the NASA Advanced Composites Project (ACP). Tests were conducted on OHC specimens with hard, quasi-isotropic, and soft layups using digital image correlation and X-Ray computed tomography to capture the structural response and damage evolution. Progressive damage models were constructed for use with the CompDam continuum damage mechanics code following the best practices established during the ACP. Detailed interrogation of the analysis results and comparison with experimental measurements provide a basis for assessing the capability of the modeling approach for OHC. The structural response is found to be captured well, with strengths predicted within 3\% of the experimental values for hard and quasi-isotropic laminates. In the soft laminate, the model predicts failure to be more brittle than the nonlinear, ductile response that was measured. Damage states extracted from the models at the same load level as test measurements are overlaid to show directly the similarities and differences between test and analysis results. Studying the damage evolution predicted by the analysis reveals that the failure process is a competition between fiber damage and delamination/sub-laminate buckling, with fiber damage dominating the collapse in the hard laminate and sub-laminate buckling governing in the soft laminate. Finally, a series of parametric studies varying numerical solution parameters (mesh size, mass scaling) and physical properties (fiber direction compressive strength and toughness) reveal sensitivities and deficiencies of the model. To the authors' knowledge, this study is the first for OHC specimens to include detailed evaluation of damage mode interactions, direct overlay of predicted and measured damage states, and sensitivity of the predicted results to difficult-to-measure fiber direction material properties.

Continuum damage mechanics↗
NASA NTRS1990

An apparatus for bearing-bypass testing of bolted joints

A dual-control test system measuring the strength of graphite/epoxy specimens under tension and compression for a wide range of bearing-bypass load ratios is presented. The bearing-bypass strengths of single-fastener specimens are measured for damage onset and ultimate failure and are plotted against one another. The results indicate that an initiated damage grows to failure in the same mode for most cases. However, if the damage is initiated in the compression-reacted-bearing mode, the specimens fail in the offset-compression mode. It is concluded that this type of transition can occur in multi-fastener joints under compression and complicate the strength predictions.

Crews, J. H., Jr.↗
NASA NTRS2021

Damage Tolerance of Candidate Sandwich Structure for the Space Launch System (SLS) Payload Adapter Fitting (PAF)

This Technical Memorandum presents results from a damage tolerance study undertaken in support of the payload adapter fitting (PAF) for the Space Launch System (SLS) program at NASA’s Marshall Space Flight Center (MSFC). The study consisted of determining the compression-after-impact (CAI) strength of candidate carbon/epoxy face sheet sandwich structure that has been identified for potential use to manufacture the PAF hardware. Two types of core material that have been considered for use on the PAF structure were used in this study. One was an aluminum honeycomb and the other was a Rohacell foam. Levels of barely visible impact damage (BVID) were determined for the types of sandwich structure tested in this study and this level of damage was used for CAI strength testing. It was found that the honeycomb core sandwich structure failed by face sheet failure and the foam core sandwich structure failed by core shear failure. CAI strength values were normalized by weight of the sandwich structure since lower mass is desirable for this structure.

sandwich structure↗
NASA NTRS1983

Effect of swaging on the 1000 C compressive slow plastic flow characteristics of the directionally solidified eutectic alloy gamma/gamma prime-alpha

Swaging between 750 and 1050 C has been investigated as a means to introduce work into the directionally solidified eutectic alloy gamma/gamma prime-alpha (Ni-32.3 wt percent Mo-6.3 wt percent Al) and increase the elevated temperature creep strength. The 1000 C slow plastic compressive flow stress-strain rate properties in air of as-grown, annealed, and worked nominally 10 and 25 percent materials have been determined. Swaging did not improve the slow plastic behavior. In fact large reductions tended to degrade the strength and produced a change in the deformation mechanism from uniform flow to one involving intense slip band formation. Comparison of 1000 C tensile and compressive strength-strain rate data reveals that deformation is independent of the stress state.

Whittenberger, J. D.↗
DOE OSTI2024

Strong interfaces: the key to high strength in nano metallic laminates

Excellent mechanical properties of nanomaterials are usually attributed to their nanoscale feature size and high-density interfaces. This work explores the effects of intrinsic interface properties on mechanical properties of nano metallic laminates (NMLs). We show that the interface strength significantly affects the mechanical properties of NMLs. Via in situ mechanical testing and characterization, we investigate the deformation behavior and concurrent microstructure evolution in NMLs with four types of dissimilar interfaces. Our results show that the strength and deformation behaviors of NMLs are largely determined by interface strength. Strong interfaces can simultaneously increase the strength, work hardening capability, and deformability of NMLs. In conclusion, this work brings new insight into the design of advanced metallic materials through tuning of interface properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Enhanced Interfacial Strength in Carbon Fiber Composites via Mussel‐Inspired Sizing Polymers

Composite materials possess a high strength-to-weight ratio. A key determinant of their mechanical performance is the interfacial strength between the fibers and the matrix. Sizing agents are commonly used to improve this interface by promoting better adhesion, though optimizing this interaction remains a significant challenge. Here, this study evaluates the use of poly(catechol-styrene) (PCS), a mussel-inspired sizing agent, to enhance fiber–matrix bonding in carbon fiber composites. Woven carbon fiber laminates were dip-coated with varying concentrations of PCS (0.05 and 0.1 wt%) and subsequently fabricated using vacuum-assisted resin transfer molding followed by compression molding. Interlaminar shear strength (ILSS) tests showed improvements of 4% and 8% for the 0.05% and 0.1% PCS treatments, respectively. These results indicate that PCS is effective in reinforcing interfacial adhesion, thereby improving the mechanical integrity of carbon fiber-reinforced composites.

Carbon fiber composites↗
DOE OSTI2019

Extreme Hardening of Pb at High Pressure and Strain Rate

We study the high-pressure strength of Pb and Pb-4wt%Sb at the National Ignition Facility. We measure Rayleigh-Taylor growth of preformed ripples ramp compressed to ~400 GPa peak pressure, among the highest-pressure strength measurements ever reported on any platform. We find agreement with 2D simulations using the Improved Steinberg-Guinan strength model for body-centered-cubic Pb; the Pb-4wt%Sb alloy behaves similarly within the error bars. Here, the combination of high-rate, pressure-induced hardening and polymorphism yield an average inferred flow stress of ~3.8 GPa at high pressure, a ~250-fold increase, changing Pb from soft to extremely strong.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Mechanical response of unidirectional boron/aluminum under combined loading

Three test methods were employed to characterize the response of unidirectional Boron/Aluminum metal matrix composite material under monotonic and cyclic loading conditions, namely, losipescu shear, off-axis tension and compression. The characterization of the elastic and plastic response includes the elastic material properties, yielding and subsequent hardening of the unidirectional composite under different stress ratios in the material principal coordinate system. Yield loci generated for different stress ratios are compared for the three different test methods, taking into account residual stresses and specimen geometry. Subsequently, the yield locus for in-plane shear is compared with the prediction of an analytical, micromechanical model. The influence of the scatter in the experimental data on the predicted yield surface is also analyzed. Lastly, the experimental material strengths in tension and compression are correlated with the maximum stress and the Tsai-Wu failure criterion.

Becker, Wolfgang↗