Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diameter effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Prompt Gamma Ray Analysis of Soil Samples

Neutron moderation effects were measured in bulk soil samples through prompt gamma ray measurements from water and benzene contaminated soil samples using 14 MeV neutron inelastic scattering. The prompt gamma rays were measured using a cylindrical 76 mm x 76 mm (diameter x height) LaBr{sub 3}:Ce detector. Since neutron moderation effects strongly depend upon hydrogen concentration of the sample, for comparison purposes, moderation effects were studied from samples containing different hydrogen concentrations. The soil samples with different hydrogen concentration were prepared by mixing soil with water as well as benzene in different weight proportions. Then, the effects of increasing water and benzene concentrations on the yields of hydrogen, carbon and silicon prompt gamma rays were measured. Moderation effects are more pronounced in soil samples mixed with water as compared to those from soil samples mixed with benzene. This is due to the fact that benzene contaminated soil samples have about 30% less hydrogen concentration by weight than the water contaminated soil samples. Results of the study will be presented. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Field study of group effects on the pullout capacity of “deep” helical piles in sand

This paper presents the results of a field load test program used to investigate group effects on the pullout capacity of single-helix “deep” helical piles/anchors in sand. The high tensile capacity and silent installation of helical piles has given them serious consideration as an alternative to conventional deep foundations and anchors for offshore renewable energy structures. New offshore applications may consider the use of groups of helical piles to resist structural loads. Group interaction effects are known to occur in helical piles, but there is a scarcity of field data on groups in sands under tensile loading. This study involved the installation and load testing of single-helix 152mm diameter round shaft piles and pile groups embedded in sand to depths of 12 and 18 helix diameters below the ground surface. The study was designed to explore the effects of close pile spacing, group configuration (i.e., number of piles), and soil strength (i.e., friction angle) as interpreted from cone penetration test (CPT) resistance. The results showed group efficiencies ranging from about 0.6 to 1.0 at a horizontal spacing of 2 to 3 times the helix diameter in sands with friction angles of about 39° to 44°. The data from this study may also be useful for validation of numerical models for analysis of helical pile group interactions.

Engineering↗

STELLAR DIAMETERS AND TEMPERATURES. I. MAIN-SEQUENCE A, F, AND G STARS

We have executed a survey of nearby, main-sequence A-, F-, and G-type stars with the CHARA Array, successfully measuring the angular diameters of forty-four stars with an average precision of {approx}1.5%. We present new measures of the bolometric flux, which in turn leads to an empirical determination of the effective temperature for the stars observed. In addition, these CHARA-determined temperatures, radii, and luminosities are fit to Yonsei-Yale model isochrones to constrain the masses and ages of the stars. These results are compared to indirect estimates of these quantities obtained by collecting photometry of the stars and applying them to model atmospheres and evolutionary isochrones. We find that for most cases, the models overestimate the effective temperature by {approx}1.5%-4% when compared to our directly measured values. The overestimated temperatures and underestimated radii in these works appear to cause an additional offset in the star's surface gravity measurements, which consequently yield higher masses and younger ages, in particular for stars with masses greater than {approx}1.3 M{sub Sun }. Additionally, we compare our measurements to a large sample of eclipsing binary stars, and excellent agreement is seen within both data sets. Finally, we present temperature relations with respect to (B - V) and (V - K) colors as well as spectral type, showing that calibration of effective temperatures with errors {approx}1% is now possible from interferometric angular diameters of stars.

79 ASTRONOMY AND ASTROPHYSICS↗

Multi-year global climatic effects of atmospheric dust from large bolide impacts

The global climatic effects of dust generated by the impact of a 10 km-diameter bolide was simulated using a one-dimensional (vertical only) globally-averaged climate model by Pollack et al. The goal of the simulation is to examine the regional climate effects, including the possibility of coastal refugia, generated by a global dust cloud in a model having realistic geographic resolution. The climate model assumes the instantaneous appearance of a global stratospheric dust cloud with initial optical depth of 10,000. The time history of optical depth decreases according to the detailed calculations of Pollack et al., reaching an optical depth of unity at day 160, and subsequently decreasing with an e-folding time of 1 year. The simulation is carried out for three years in order to examine the atmospheric effects and recovery over several seasons. The simulation does not include any effects of NOx, CO2, or wildfire smoke injections that may accompany the creation of the dust cloud. The global distribution of surface temperature changes, freezing events, precipitation and soil moisture effects and sea ice increases will be discussed.

Thompson, Starley L.↗

Weak phylogenetic and habitat effects on root trait variation of 218 Neotropical tree species

Tropical forests harbor a large diversity of closely related tree species that can thrive across habitats. This biodiversity has been found to correspond to large functional diversity in aboveground traits, and likely also relates to belowground trait variation. Globally, root trait (co-)variation is driven by different belowground resource strategies of species, environmental variation, and phylogeny; however, these patterns mostly reflect observations from temperate biomes and remain unconfirmed in tropical trees. We examine phylogenetic and environmental effects on root trait (co-)variation of trees across habitats in an Amazonian rainforest. Roots of 218 tree species from ten dominant families were sampled across three major habitats near Manaus, Brazil. We quantified five morphological and architectural root traits to (i) investigate how they reflected different resource strategies across species, (ii) compare them between families and superorders to test phylogenetic effects, and (iii) compare them between habitats to determine environmental effects on root trait expressions and variability. Root traits discriminated species along a tradeoff between root diameter and root branching and, secondly, due to variation in root tissue density. Our results further show weak phylogenetic effects on tropical tree root variation, for example, families from the same superorder showed large divergence in their root traits, while those from different superorders often overlapped in their root morphology and architecture. Root traits differed significantly between habitats but habitat type had only little effect on overall root trait variation. Our work suggests that the dimensions and drivers that underlie (co-)variation in tropical root traits may differ from global patterns defined by mostly temperate datasets. Due to (a)biotic environmental differences, different root trait dimensions may underlie the belowground functional diversity in (Neo)tropical forests, and we found little evidence for the strong phylogenetic conservatism observed in root traits in temperate biomes. We highlight important avenues for future research on tropical roots in order to determine the degree of, and shifts in functional diversity belowground as communities and environments change in tropical forests.

59 BASIC BIOLOGICAL SCIENCES↗

Effect of molecular shape on rotation under severe confinement

Orientational structure and dynamics of molecules is known to be affected by confinement in space comparable in size to the molecule itself. ZSM-5 with porous channels of ≈0.55 nm is such a porous medium, which offers a strict spatial confinement on low molecular weight hydrocarbons. An important factor that determines these properties is the shape of the confined molecules. In this work, we employed molecular dynamics simulation to study the orientational structure and dynamics of four molecules that differ in shape but have similar kinetic diameters and moments of inertia, confined in ZSM-5. The effect of molecular shape on the orientational structure and dynamics of propane, acetonitrile, acetaldehyde and acetone in ZSM-5 is studied by means of probing the differences in the orientational distribution of molecules in the ZSM-5 channels, and extracting time scales of the decay of correlation functions related to rotational motion. Orientational correlation functions of all the four molecules exhibit two regimes of rotational motion. While the short time regime represents free rotation of the molecules before they collide with the pore walls, the long time orientational jumps driven by inter-channel migrations give rise to a very slow varying second regime. Of the molecules studied, orientational structure and dynamics of propane is found to be least affected by confinement under ZSM-5, whereas charge and shape asymmetry of other molecules makes their interchannel migration-driven rotation slow. The time scales involved in the rotational motion for the molecules studied are compared with similar studies reported in literature. Lastly, this study reveals the important role that molecular shape plays in the behavior of confined molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Pressure effect on a tandem hollow cathode discharge in argon

The tandem hollow cathode discharge, formulated by arranging two discharges in series, is an important method used to increase the irradiance of a hollow cathode discharge. Here in this paper, based on a two-dimensional fluid model we studied a five-layer tandem hollow cathode discharge, with three hollow electrodes stacked together and separated by the insulators to obtain the configuration of anode/insulator/cathode/insulator/anode from the top to the bottom. In the model, the thickness of both electrodes and insulators is set at 1 cm and the diameter of the hollow cavity is 2 cm. The pressure effect on the discharge properties is investigated with gas pressure ranges from 100 Pa to 5 kPa. The gap voltage first decreases, reaching a minimum sustaining voltage at 1 kPa, and then increases. Based on the two-dimensional electron density distributions, the discharges parameters (including the electron density, ion density, electric potential, and electric field) of one integrated hollow cathode discharge at 1 kPa and two relatively independent discharges at 100 Pa and 4 kPa are presented, respectively. Lastly, the results indicate that the paralleled hollow cathode discharges can be manipulated into one integrated discharge with a higher plasma density by the monotonous control of gas pressure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of CO2 gasification reaction on oxycombustion of pulverized coal char.

For oxy-combustion with flue gas recirculation, as is commonly employed, it is recognized that elevated CO{sub 2} levels affect radiant transport, the heat capacity of the gas, and other gas transport properties. A topic of widespread speculation has concerned the effect of the CO{sub 2} gasification reaction with coal char on the char burning rate. To give clarity to the likely impact of this reaction on the oxy-fuel combustion of pulverized coal char, the Surface Kinetics in Porous Particles (SKIPPY) code was employed for a range of potential CO{sub 2} reaction rates for a high-volatile bituminous coal char particle (130 {micro}m diameter) reacting in several O{sub 2} concentration environments. The effects of boundary layer chemistry are also examined in this analysis. Under oxygen-enriched conditions, boundary layer reactions (converting CO to CO{sub 2}, with concomitant heat release) are shown to increase the char particle temperature and burning rate, while decreasing the O{sub 2} concentration at the particle surface. The CO{sub 2} gasification reaction acts to reduce the char particle temperature (because of the reaction endothermicity) and thereby reduces the rate of char oxidation. Interestingly, the presence of the CO{sub 2} gasification reaction increases the char conversion rate for combustion at low O{sub 2} concentrations, but decreases char conversion for combustion at high O{sub 2} concentrations. These calculations give new insight into the complexity of the effects from the CO{sub 2} gasification reaction and should help improve the understanding of experimentally measured oxy-fuel char combustion and burnout trends in the literature.

01 COAL, LIGNITE, AND PEAT↗

Ways to Increase Launch Velocities of 2-Stage Gas Guns

The amount of space debris is rapidly increasing and the debris is distributed over a wide variety of orbits. Satellites, manned space vehicles and space stations will have to pay increasing attention to the dangers of impacts with space debris. Various armoring techniques (i.e., double or triple layer armor) will have to tested extensively to determine the most effective armor per unit weight. Intersecting near-earth orbits can lead to impact velocities up to 15 km/sec. Conventional two-stage light gas guns can launch intact, controlled-shape projectiles with a density of 1.2 gm/cc and length- to-diameter ratios of 0.5-1.0 at velocities up to 8-9 km/sec. Higher velocities (10-11 km/sec) can be obtained' for very light projectiles. The higher launch velocities tend to be very severe on the high pressure coupling and barrel of the gun and lead to short component lifetimes. Clearly, the ability to raise the launch velocity of a gun (for reasonably massive projectile shapes) from 8-9 km/sec to 11-13 km/sec (or higher), without reduction of component lifetimes, would have significant benefits. This would allow much better simulation of the higher velocity debris impacts as well as better simulation of high speed re-entry into planetary atmospheres. Several techniques for increasing the launcher muzzle velocity above 8-9 km/sec have been studied using CFD simulations and appear to offer the potential for significant gains. The first technique is to use multiple compressions, instead of a single compression, in the pump tube of the light gas gun. In a sense, this is a kind of pre-heating of the gas in the pump tube; other types of pre-heating have yielded disappointing results in the past. The dynamics of the multiple compression pump tube is very different, however, from the earlier techniques, where the pump tube was typically heated ohmically before the gun 2 cycle was started. In this paper, we present CFD calculations that show that significant increases in muzzle velocity can be obtained with multiple compressions in the pump tube. With a conventional two-stage gun, an important limitation to obtaining higher velocities is friction and heat transfer to the barrel, which typically has a length- to- diameter ratio of 200-400. These viscous losses greatly reduce the effectiveness of the regions of the barrel far removed from the second stage breech. We have studied computationally the effect of adding an additional breech (or breeches) along the barrel to reduce these viscous losses. Velocity increases from 6.5 to 7.2 km/sec have been obtained using the main breech and one additional breech. In these results, both breeches were operated with hydrogen, heated electrothermally. We have also studied a gun geometry where the main breech is operated in the conventional manner, using piston compression. The additional breech is operated either with electrothermal heating or heating by using a high explosive charge in a novel geometry. The latter option provides very effective compression, heating and acceleration of the hydrogen working gas and is fully reusable. Calculations are presented which show that very substantial increases in muzzle velocity can be obtained this way, without overstressing the projectile or the 'gun. The third technique studied is to add a section of ram accelerator tube after the barrel to further accelerate the projectile. The ram accelerator used here is not the conventional premixed gas ram accelerator, but a new technique using high explosive as the energy source and pure hydrogen as the working gas in a geometry which can be made fully reusable. Preliminary results with this new rain accelerator geometry were presented and showed that stable ram accelerator drive can be established. Herein, detailed calculations axe presented which show that substantial velocity increases can be obtained using this ram accelerator technique in tandem with a conventional light gas gun.

Bogdanoff, David W.↗

Magnetostatic effects on switching in small magnetic tunnel junctions

Perpendicular CoFeB/MgO/CoFeB magnetic tunnel junctions with diameters under 100 nm are investigated by conductive atomic force microscopy. Minor loops of the tunnel magnetoresistance as a function of applied magnetic field reveal the hysteresis of the soft layer and an offset due to the magnetostatic field of the hard layer. Within the hysteretic region, telegraph noise is observed in the tunnel current. Simulations show that in this range, the net magnetic field in the soft layer is spatially inhomogeneous, and that antiparallel to parallel switching tends to start near the edge, while parallel to antiparallel reversal favors nucleation in the interior of the soft layer. As the diameter of the tunnel junction is decreased, the average magnitude of the magnetostatic field increases, but the spatial inhomogeneity across the soft layer is reduced.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The effect of open-cell metal foams strut shape on convection heat transfer and pressure drop

Metal foams are promising materials for applications where enhancement of heat transfer is needed. Their performance depends on morphological parameters, such as the diameters of cells, pores, and struts, the porosity, the shape of struts. The effect of strut shape on convection heat transfer and pressure drop in open-cell metal foams has been investigated numerically in this paper by introducing the foam shape factor, a parameter that characterizes the shape of the strut. The analysis has been carried out both on real and ideal foams. The geometry of three 40 Pores Per Inch (PPI) real foams, with 0.87, 0.94 and 0.96 average measured porosities, was determined with X-ray Computed Microtomography (XCT) and a morphological analysis of the XCT data was carried out. The geometry of the ideal foams, based on the Lord Kelvin foam model, with the same PPI and porosities as those of the real foams, was generated with the free-to-use software Surface Evolver, building up foams with different strut shapes. Governing equations have been solved with a finite element scheme, assuming a uniform heat flux condition at the solid/fluid boundary of the foam. Results are presented in terms of convection heat transfer coefficients and pressure distributions as a function of strut shape parameters. Here, the comparison between predictions for ideal and real foams, for different strut shapes, confirms that, in all cases, the closer the form of the ideal strut to that of the real strut the better the agreement among predictions. It is also pointed out that the convection heat transfer coefficient is maximized when, at equal porosity, the ligament shape is convex, while a concave strut shape maximizes the pressure drop.

42 ENGINEERING↗

Computational Modeling of Multi-Pass Rolling Parameters Effect on Resulting Fuel Foil Shape

A focus of the U.S. Department of Energy is to improve production yield and reduce the cost of Low Enriched Uranium (LEU)-molybdenum alloy (U-10Mo) monolithic fuel plates that will be replacing High Enriched Uranium (HEU) oxide dispersion fuels used currently in the United States High Performance Research Reactors (USHPRR). One area of improvement is lowering the high transverse waviness and longitudinal waviness currently present within rolled foils prior to cladding to produce fuel plates. Traditional rolling manufacturing techniques for other metal foils use winders to pull and straighten the foil as it is rolled back and forth to the final thickness. This approach cannot be used to roll thin U-10Mo foils (0.008-0.025” thick) because only small castings can be rolled due to nuclear criticality safety concerns. As a result, the fuel foils are too short (1 m in length) to use traditional winders. Therefore, it is crucial to identify other rolling parameters (i.e., roller friction, axial tension load, roller diameter, and roll pass reduction percent) that might reduce transverse waviness and longitudinal waviness in the rolled fuel foil and develop a high-yield, low-cost multi-pass rolling manufacturing process. This report documents a systematic finite element modeling study to investigate the effects of numerous rolling parameters to reduce resulting transverse waviness and longitudinal waviness in the fuel foil during multi-pass rolling of U-10Mo foils. The rolling of a U-10Mo plate with initial dimensions of 1”x1”x 0.048” is modeled using Abaqus CAE. This rolling is modeled to undergo eight 20% reduction roll passes to a final fuel foil thickness of 0.01”. The elastic-plastic constitutive model of the U-10Mo alloy was input to the fuel foil rolling model. The rollers were modeled as rigid bodies. A comparison of rolling friction coefficients of 0.3 and 0.7 over a wide range of applied axial tension loads were investigated in order to evaluate the effect of using a lubricant during rolling. The effect of roller diameter on the resulting transverse waviness and longitudinal waviness of the fuel foil over a wide range of axial tension loads were also investigated by modeling rollers 7/8” and 3.75” in diameter. The results of this systematic finite element method study will aid manufacturers in producing low transverse waviness and reduced longitudinal waviness in U-10Mo fuel foils.

U-10Mo, FEA, Rolling, Residual Stress, Fuel Foil↗

Effects of Headspace and Oxygen Level on Off-gas Emissions from Wood Pellets in Storage

Few papers have been published in the open literature on the emissions from biomass fuels, including wood pellets, during the storage and transportation and their potential health impacts. The purpose of this study is to provide data on the concentrations, emission factors, and emission rate factors of CO2, CO, and CH4 from wood pellets stored with different headspace to container volume ratios with different initial oxygen levels, in order to develop methods to reduce the toxic off-gas emissions and accumulation in storage spaces. Metal containers (45 l, 305 mm diameter by 610 mm long) were used to study the effect of headspace and oxygen levels on the off-gas emissions from wood pellets. Concentrations of CO2, CO, and CH4 in the headspace were measured using a gas chromatograph as a function of storage time. The results showed that the ratio of the headspace ratios and initial oxygen levels in the storage space significantly affected the off-gas emissions from wood pellets stored in a sealed container. Higher peak emission factors and higher emission rates are associated with higher headspace ratios. Lower emissions of CO2 and CO were generated at room temperature under lower oxygen levels, whereas CH4 emission is insensitive to the oxygen level. Replacing oxygen with inert gases in the storage space is thus a potentially effective method to reduce the biomass degradation and toxic off-gas emissions. The proper ventilation of the storage space can also be used to maintain a high oxygen level and low concentrations of toxic off-gassing compounds in the storage space, which is especially useful during the loading and unloading operations to control the hazards associated with the storage and transportation of wood pellets.

09 BIOMASS FUELS↗

An influence of manufacturing tolerances on Pin-Cell k-infinity of MOX fuel using data from the FUBILA experiment program

An influence of manufacturing tolerances (MTs) was evaluated on the pin-cell k-infinity of MOX fuel through the random sampling of CASMO5 calculations. The data from the FUBILA experiment program was used as the manufacturing parameters. For the uncertainties of element/isotope mass fractions, their covariance matrices were calculated by the generalized least square method. The total k-infinity uncertainty was 120-250 pcm (percent mille). From the breakdown of k-infinity uncertainty per materials, the MTs of fuel pellet had a dominant influence. The individual influences were also evaluated for element/isotope mass fractions, an inner/outer diameter, and a density. Those of element/isotope mass fractions were less than a few dozen pcm. Since the perturbations of fuel pellet diameter and density caused large variations to the total amount of heavy metals and effect of spatial self-shielding, they had a negative correlation with the k-infinity perturbation. On the AG3 (Al-Mg alloy) over-cladding, the inner/outer diameter perturbations had both negative and positive correlations. The negative one was due to decrease in amount of light water and the positive one was due to increase in amount of AG3. Since the effect of neutron slowing-down by light water had a dominant influence, the influence of the former negative correlation was larger than that of the latter positive correlation. It is, therefore, concluded that the consideration of the MTs that had a large influence on the effect of neutron slowing-down is important for precise quantification of the pin-cell k-infinity uncertainty of MOX fuel. (author)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Technology Development for the Constellation-X Spectroscopy X-Ray Telescope

The Constellation-X Spectroscopy X-ray Telescope (SXT) is a large diameter, high throughput, grazing incidence imaging mirror system, designed to perform high sensitivity spectroscopy of cosmic X-ray sources in the 0.2-10.0 keV band. The baseline effective area requirement is -3 m# at 1 keV. The system-level angular-resolution requirement is a 15-arcseconds half-power diameter, with a 5-arcsecond goal. The effective area is attained through a modular design, involving the nesting of many confocal, thin-walled Wolter I mirror segments. Considerable progress has been made in developing thin, thermally formed, glass mirror substrates that meet or better the angular-resolution requirement. Several approaches to mounting and aligning reflector segments into a mirror system are under investigation. We report here on the progress of the SXT technology development program toward reaching the performance goals.

Petre, Robert↗

Deformation Behavior and TExture Evolution of Steel Alloys under Axial-Torsional Loading

Using hollow cylinder samples with suitable geometry obtained from round bar stock, the deformation behavior of bcc Fe based 12L14 steel alloy is evaluated under multi-axial conditions. A stacked strain gage rosette and extensometer mounted on the cylindrical surface at the mid height of the specimen provided strain tensor as a function of applied stress for pure tensile and torsion tests prior to yielding. This study examines elastic and yield behavior and effects of these with respect to texture evolution. Hollow cylinder specimen geometry (tubes) with small wall thickness and relatively (to its thickness) large inner diameter is used. The variation of observed yield surface in deviatoric plane and the effect on mode of deformation (tension versus torsion versus its combination) on stress-strain behavior is discussed. Bulk texture was studied using neutron time-of-flight diffractometer at High-Pressure-Preferred Orientation (HIPPO) - Los Alamos Neutron Science Center (LANSCE) instrument and the evolution of texture and related anisotropy for pure tension versus torsion are also included.

36 MATERIALS SCIENCE↗

Sol-gel Synthesis and Characterization of Gels with Compositions Relevant to Hydrated Glass Alteration Layers

During the processes associated with glass corrosion, porous alteration gel layers typically form upon exposure to aqueous conditions for extended time periods. The impacts of the alteration gel layer on glass durability have not been agreed upon in the glass science community. In particular, the formation mechanisms of the alteration gel layers are still largely unknown and require further investigation. However, alteration gel layers often require months to years to develop and are often too thin to adequately characterize. Meanwhile, silicate sol-gels are relatively easy to synthesize in bulk with custom compositions relevant to alteration gel layers. If glass alteration gel layers and synthetic sol-gel silicate gels demonstrate physical and chemical properties that are sufficiently similar, synthetic silicate gels could be used as analogues for glass alteration gel layers in future studies. In this study, sol-gels were made with custom compositions at various pH values to evaluate the effect of pH on gel structure and morphology. Several other variables were examined as well, such as composition, drying, and aging. Sol-gels were created by sequential additions of organometallic precursors in a single container. Synthesis procedural steps are provided in further detail within the text. Sol-gels were analyzed with several techniques including Small Angle X-ray Scattering (SAXS), gas adsorption, and He pynchometry to determine the effects of the variables on physical properties. Results show that sol-gels prepared at pH 3 consistently contained fewer primary particles with diameters larger than 72 Å and fewer pores with diameters larger than 300 Å compared to sol-gels synthesized at pH 7 and 9. Composition was shown to have no discernable effect on primary particle and pore sizes at any pH.

Reiser, Joelle TG↗

Geometric factors affecting noise suppresion and thrust loss of divergent-lobe supersonic jet noise suppressor

The thrust loss and noise suppression of a divergent-lobe supersonic jet noise suppressor were experimentally determined over a range of nozzle pressure ratios of 1.5 to 4.0. These small-scale cold flow tests were made to determine the effect on thrust and noise of: suppressor length, rearward facing step height, suppressor divergence angle, and ejector shroud length and location. Noise suppression was achieved at nozzle pressure ratios of 2.5 and greater. Maximum lobe jet noise attenuation of 15 db with thrust loss differences of 1.5 percent compared to the convergent nozzle were obtained at a nozzle pressure ratio of 3.5 with an ejector shroud two nozzle diameters long. Without the ejector the attenuation was 13 db with thrust loss differences of 11 percent. Short suppressors approximately one primary nozzle throat diameter long performed as well as longer suppressors. Rearward facing step height had a significant effect on noise suppression. Ejector shrouds two nozzle diameters in length are feasible.

Huff, R. G.↗