SEARCH · Search NASA

Results for “EUTECTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

All sources NASA NTRS DOE OSTI

DOE OSTI2017

On a neutron detector based on TlInSe{sub 2} crystals intercalated with a lithium isotope

The possibility of increasing the sensitivity of a neutron detector based on a TlInSe{sub 2} crystal by introducing the {sup 6}Li isotope into this crystal is investigated. Introduction of the isotope is conducted by the method of electrochemical intercalation from aqueous and nonaqueous solutions of LiCl and also from the melt of the LiCl–KCl eutectic. It is shown that intercalation by the electrochemical method from a LiCl solution in propylene carbonate, performed along the “c” axis of the crystal (along strong bond chains) is efficient. The attained concentration of introduced lithium amounts to (1–1.2) × 10{sup 21} cm{sup –3}, which increased the sensitivity of the detector by approximately four times. Good agreement between the calculated and experimental values of the detector sensitivity is demonstrated.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Corrosion of Commercial Mg–Al Alloys: AZ31B, AM60, and AZ91D

Aqueous corrosion, atmospheric corrosion, and ionic liquid dissolution studies were performed on commercial alloys AZ31B, AM60, and AZ91D and compared with previously reported results for single-phase binary Mg–Al alloys containing similar Al concentrations (αMg-2 at% Al, αMg-5 at% Al, and Mg-8 at% Al). Polarization studies in 0.6 M NaCl were used to characterize the aqueous free corrosion behavior during 20-h free immersion. Accelerated corrosion testing was performed using a rotating-disk electrode which revealed the evolution of an Al-rich mud-cracking and platelet morphology. Atmospheric droplet testing showed rapid pH increases that depended on the Al concentration in the alloy. Time-dependent contact angle measurements showed that the degree of droplet wetting increased during free corrosion by ~50° over 20 h in 0.6 M NaCl. Ionic liquid dissolution studies in 1:2 M choline chloride:urea deep eutectic solvent were performed in order to examine the current-voltage behavior of these alloys in the absence of water and hydrogen reduction. The results of these studies revealed the formation of nanowire corrosion morphologies within a honeycomb lattice structure which we attribute to selective dissolution of Mg via a two-dimensional stepflow process

25 ENERGY STORAGE↗

DOE OSTI2022

Perspective—Hydrogen Bonded Concentrated Electrolytes for Redox Flow Batteries: Limitations and Prospects

This perspective provides a brief overview of the recent work on electrolytes with hydrogen (H)-bonding network, specifically the deep eutectic solvents (DESs), and outlines important factors to consider when adapting these electrolytes in redox flow batteries (RFBs). The redox behavior, solubility, and stability of several redox molecules of relevance to RFBs in DESs are presented, including some of our work within the Breakthrough Electrolytes for Energy Storage (BEES)—an Energy Frontier Research Center of the United States Department of Energy. Particularly, the challenges and opportunities for further development of DESs for energy storage are discussed.

25 ENERGY STORAGE↗

DOE OSTI2023

Determination of Kinetic Properties of Ni(II) Ions in Molten LiF-NaF-KF via Voltammetry

Kinetic properties of Ni(II) in eutectic LiF-NaF-KF (FLiNaK) molten salt were determined at T = 748–823 K using cyclic voltammetry (CV), square wave voltammetry (SWV), and chronoamperometry (CA) measurements using a glassy C working electrode, Ni(II)/Ni reference electrode, and Ni counter electrode. Reduction of Ni(II) to Ni(s) was determined to be a single step, two-electron transfer process. Diffusivity values were calculated using the Berzins and Delahay equation and semi-integral electroanalysis from the CV measurements as well as using the Cottrell equation from the CA measurements. Diffusivity of Ni(II) in molten FLiNaK at T = 748–823 K was determined to be 3.27 × 10 –7 –3.04 × 10 –6 cm 2 s –1 with an activation energy of 62–104 kJ mol –1 . The estimated kinetic properties varied appreciably among methodologies possibly due to inherent assumptions in theory regarding reversibility and unit activity during Ni metal deposition on the working electrode.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Methods—Meso-Scale Electrodes for Characterizing Diffusion-Reaction Properties of Redox-Active Organics in Viscous Electrolytes

Deep Eutectic Solvents (DESs) have recently gained interest as flow battery electrolytes. Their advantages include a wider electrochemical stability window compared to aqueous electrolytes, higher solubility for redox-active species, and negligible volatility. However, DESs are often highly viscous, and suffer from low ionic conductivities. This can make assessing redox kinetics difficult when attempting to determine their viability for energy storage. In classical voltammetric measurements, low ionic conductivity manifests as high solution resistance, thereby requiring "live" compensation of the electrolyte ohmic drop when performing fast-scan voltammetry. An uncompensated or inadequately-compensated ohmic drop leads to misinterpretation of the voltammetric behavior, e.g., assessing reversibility vs. irreversibility of a redox reaction. Here, we present micro-fabricated electrodes as facile "meso-scale" electrodes, which overcome these issues by nearly eliminating the ohmic drop while retaining uniformity of the current distribution over the electrode surface. Their use in precise transport-kinetics measurements is demonstrated using a redox-active organic, i.e., 4-Hydroxy-TEMPO in an aqueous medium and in ethaline, which is a viscous DES. This study provides a methodical approach to design and to implement voltammetry experiments using meso-scale electrodes leading to reliable measurements of diffusion-reaction properties of 4-Hydroxy-TEMPO.

25 ENERGY STORAGE↗

DOE OSTI2024

The Effect of Sulfuric Acid Anodization on the Electrochemical Properties of Aluminum Alloy AlSi 10 Mg Prepared by Selective Laser Melting

Aluminum alloy, AlSi 10 Mg, prepared by selective laser melt (SLM) fabrication was anodized in 9.8% sulfuric acid (Type II) at 15 V for a total of 23 min. Experiments were performed to study the potentiostatic anodization process and its effects on the oxide coating morphology, thickness, and electrochemical properties of the alloy. Prior to anodization, the alloy microstructure is composed of aluminum cells encapsulated in a silicon network. Anodizing the abraded and polished AlSi 10 Mg surface produced a porous oxide layer with a thickness of 5μm. The oxide coating weight was 698 ± 29 mg/ft 2 . The oxide coating forms in the aluminum cells that are isolated from one another by the silicon eutectic phase. In electrochemical tests, the anodic and cathodic potentiodynamic polarization currents were suppressed by factors of 15× and 215×, respectively, as compared to the unanodized controls. The data indicate the anodic oxide coating suppresses the cathodic more than the anodic reaction rate. Linear polarization resistance (R p ) values increased by 279× after anodization. The corrosion current density values (j corr ) decreased by 133× after anodization. Taken together, the electrochemical data indicate the anodic oxide coating (unsealed) increases the corrosion resistance of the SLM alloy by two orders of magnitude.

Electrochemistry↗

DOE OSTI2025

Effect of Soluble Corrosion Products on Electrical Double Layer in LiCl-KCl Molten Salts

Corrosion in molten salts greatly hampers the application for renewable energy applications like molten salt reactors. To develop effective strategies for corrosion mitigation, understanding the interfacial structures and properties such as specific ion adsorption and electrical double layer capacitance are crucial. Using cyclic voltammetry and electrochemical impedance spectroscopy, we systematically studied the interfaces on various model electrodes including W (solid), Bi (liquid), and the stainless steel 316 in LiCl-KCl eutectic molten salts with the addition of corrosion species CrCl 2 and FeCl 2 . Both Cr 2+ and Fe 2+ ions increased electrical double layer capacitance, with Cr 2+ showing specific adsorption behavior and shifting the potential of zero charge, while Fe 2+ had minimal effect on point of zero charge. Two-working electrode measurements revealed increasing open-circuit potential and electrical double layer capacitance during the exposure of stainless steel 316, indicating its progressive corrosion and ion accumulation at the interface. X-ray photoelectron spectroscopy and Raman confirmed Cr enrichment at the interface. This work highlights the strong correlation between electrical double layer behavior and corrosion dynamics in molten salts and suggests electrical double layer capacitance as a sensitive, in situ indicator for corrosion monitoring.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2026

Progress and Perspectives: Zirconium Electrodeposition from Different Electrolytes

Zirconium (Zr) possesses outstanding properties, including exceptional chemical resistance and a high melting point, and is therefore desirable for use in a wide variety of challenging environments, such as in nuclear reactors and the chemical processing industry. To minimize the amount of Zr required for any given application, developing methods for generating metallic Zr coatings is highly advantageous. Owing to Zr’s highly negative reduction potential, electrodeposition in traditional solvents at near ambient temperatures remains challenging and thus not well understood. Due to the extreme conditions required to deposit this metal, extensive work has been conducted in molten salt electrolytes, however the broad applicability of this methodology is limited due to its corrosivity. The primary focus of this article is to present an overview of Zr’s electrochemical behavior and to consolidate the efforts of researchers in exploring electrodeposition techniques for Zr involving aqueous, organic, ionic liquid, deep eutectic, and molten salt solvents. With this information, we highlight trends across solvent systems and opportunities for future research.

42 ENGINEERING↗

DOE OSTI2026

Investigation Into LiCl-LiF+Li 2 O as a Low Temperature Electrolyte in Direct Electrolytic Reduction of UO 2

Direct electrolytic reduction (DER) of UO 2 in a binary LiCl-Li2O (1–3 wt%) at 650 °C has been widely reported. The process temperature can be reduced to 550 °C in theory by using a near eutectic ternary LiCl-LiF+Li 2O (∼2 wt%) electrolyte, which will result in substantial reduction in rate of salt vaporization. The feasibility of using the ternary electrolyte for the process was tested via material compatibility testing, electrochemical polarization testing, and controlled potential or current DER experiments. MgO, Pt, and 625 nickel samples were each contacted with the ternary salt for 168 h. Negligible changes to dimensions and mass of the samples were measured, and concentrations of corrosion products in the salt were 102 ppm or less. O2−oxidation was observed to occur at a lower potential than Cl-or F-on a Pt anode. DER of UO2was performed in six trials. Process variables included type of reference electrode, electrochemical control method, type of cathode basket, and electrolyte composition. UO 2conversion ranged from 28.2 to 99.9 % , and current efficiency ranged from 38 to 52%. Overall, results indicate that the use of the ternary salt is feasible for DER.

36 MATERIALS SCIENCE↗

DOE OSTI2017

Electrochemical Nucleation and Growth of Uranium and Plutonium from Molten Salts

This work examines the nucleation and growth behavior of uranium and plutonium from molten LiCl-KCl eutectic on inert electrodes using electrochemical techniques. Current-time transients obtained from chronoamperometric experiments were compared with theoretical models to characterize the type of nucleation (progressive or instantaneous) for deposition of U and Pu, and co-deposition of U-Pu, from molten LiCl-KCl at inert electrodes. It was established that the nucleation mode of actinides present as chlorides in molten chloride salts changes from progressive to instantaneous with an increasing concentration of the trivalent actinide ions in the salt. The effect of the material of the working electrode was investigated, and it was found that changing the material from tungsten to silver improves resolvability of the nucleation peaks and allows more accurate analysis of the experimental measurements. Using the nucleation data, diffusion coefficients were obtained for U 3+ and Pu 3+ , and were found to be in very good agreement with the values obtained from other studies. Furthermore, the density of nuclei produced during instantaneous nucleation, the rate of nucleation for progressive nucleation, and the radius of the deposited nuclei were evaluated and examined at different overpotentials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Electrochemical Recovery of Iron from Spent Pickle Liquor by Chloride-Based Molten Salt Electrolysis

Spent pickle liquor (SPL) is a waste stream generated in the steel industry that presents both a disposal challenge and a potential resource for metal recovery. This study investigates the electrochemical extraction of high-purity iron metal from SPL using chloride-based molten salt electrolysis (CMSE). Electrochemical characterization of diluted SPL confirmed Fe 2+ as the dominant species. Thermal dehydration of SPL under inert atmosphere yielded FeCl 2 -rich solids, which were directly employed as feedstock for electrolysis in LiCl–KCl eutectic melts at 500 °C. Cyclic voltammetry of FeCl 2 in this melt revealed well-defined Fe 2+ /Fe 0 redox behavior within the electrochemical stability window of the supporting electrolyte. High coulombic efficiency (>85%) electrodeposition was achieved demonstrating that iron metal can be produced from dehydrated SPL by CMSE. The electrodeposited iron exhibited >98 wt% purity, which was further enhanced to 99.9 wt% via arc melting. The resulting iron powder was ferromagnetic, and its size distribution was found to be suitable for powder metallurgy applications. This work demonstrates a scalable, energy-efficient pathway for valorizing SPL into high-purity iron metal, advancing circular economy strategies in the steel industry.

Materials science↗

DOE OSTI2018

Experimental demonstration of hydraulic jump control in liquid metal channel flow using Lorentz force

In this paper, hydraulic jump control using electromagnetic force in a liquid metal flow is presented. The control methods used give insight into the hydraulic jump behavior in the presence of magnetic fields and electrical currents. Flowing liquid metals is a proposed solution to heat flux challenges posed in fusion reactors, specifically the tokamak. Unfortunately, thin, fast-flowing liquid metal divertor concepts for fusion reactors are susceptible to hydraulic jumps that drastically reduce the liquid metal flow speed, leading to potential problems such as excessive evaporation, unsteady power removal, and possible plasma disruption. Highly electrically conductive flows within the magnetic fields do not exhibit traditional hydraulic jump behavior. There is very little research investigating the use of externally injected electrical currents and magnetic fields to control liquid metal hydraulic jumps. By using externally injected electrical currents and a magnetic field, a Lorentz force (also referred to as j × B force) may be generated to control the liquid metal jump behavior. In this work, a free-surface liquid metal—GaInSn eutectic or “galinstan”—flow through an electrically insulating rectangular duct was investigated. It was shown that applying a Lorentz force has a repeatable and predictable impact on the hydraulic jump, which can be used for liquid metal control within next-generation fusion reactors.

MHD↗

DOE OSTI2023

Detection of Off-Gassed Products From Molten Salts Using Laser-Induced Breakdown Spectroscopy

The detection of off-gassed sodium from molten sodium nitrate (NaNO 3 ) at temperatures between 330 °C and 505 °C and off-gassed calcium from molten lithium chloride–potassium chloride eutectic (LKE) mixtures at 510 °C with laser-induced breakdown spectroscopy (LIBS) was demonstrated. NaNO 3 and LKE samples were melted in a custom-built crucible that promoted the generation of off-gassed products from the molten sample. The off-gassed products were analyzed with a LIBS system designed to probe the high-temperature environment. Na D emission lines, Na(I)588.99 nm and Na(I) 589.59 nm, were detected from the NaNO 3 samples after reaching a temperature threshold, which indicated the occurrence of phase change. In LKE mixtures, the detection of Ca impurities at a concentration of 78 mg/kg was possible using the emission lines Ca(II) 393.66 nm and Ca(II) 395.85 nm. Furthermore, this work demonstrates the real-time monitoring capabilities of LIBS in high-temperature environments that simulate the conditions of molten salt reactors.

42 ENGINEERING↗

DOE OSTI2025

Data for "Integrated Green Biorefinery for the Production of Anthocyanins, Fermentable Sugars, and High Pure Lignin from Miscanthus × giganteus "

Miscanthus x giganteus (Mxg) is a promising perennial crop for producing natural colorants, renewable fuels, and bioproducts. However, natural recalcitrance and high pretreatment cost are major barriers to their complete conversion. In this study, a green processing method has been investigated for efficient recovery of natural pigments (anthocyanins), fermentable sugars, and pure lignin from Mxg genotypes using choline chloride-based natural deep eutectic solvents (NADES) systems. Interestingly, choline chloride: lactic acid (ChCl: LA) NADES-processed biomass resulted in 67.8 ± 2.1 μg g−1 of anthocyanins from dry biomass. A maximum of 87.4%–94.1% glucose yield was achieved after enzymatic saccharification. The effective extraction of lignin with high purity with higher β-aryl ether (βO4) bonds from advanced crops is crucial for lignin valorization. Notably, highly pure lignin (≈93.4% ± 1.4%) is achieved after low-temperature NADES pretreatment while retaining lignin’s native structure. 31P nuclear magnetic resonance demonstrated that total phenolics for ChCl: LA-lignin resulted in 1.20 mmol g−1 hydroxyls. The relative monolignol composition of syringyl (S), guaiacyl (G), and p-hydroxyphenyl (H) is 19.0, 65.7, and 14.3%, respectively, as evidenced by heteronuclear single quantum coherence analysis. This study provides a novel approach for obtaining high-purity lignin for catalytic depolymerization for oligomers and bifunctional monoaromatics production and leverages current cellulosic biorefinery technologies.

biomass analytics↗

DOE OSTI2017

Improved Application of Local Models to Steel Corrosion in Lead-Bismuth Loops

The corrosion of steels exposed to flowing liquid metals is influenced by local and global conditions of flow systems. The present study improves the previous local models when applied to closed loops by incorporating some global condition effects. In particular the bulk corrosion product concentration is calculated based on balancing the dissolution and precipitation in the entire closed loop. Mass transfer expressions developed in aqueous medium and an analytical expression are tested in the liquid-metal environments. The improved model is applied to a pure lead loop and produces results closer to the experimental data than the previous local models do. The model is also applied to a lead-bismuth eutectic (LBE) test loop. Systematic studies illustrate the effects of the flow rate, the oxygen concentration in LBE, and the temperature profile on the corrosion rate.

36 MATERIALS SCIENCE↗

DOE OSTI2016

Thermochemical Compatibility and Oxidation Resistance of Advanced LWR Fuel Cladding

We assessed the thermochemical compatibility of potential replacement cladding materials for zirconium alloys in light water reactors. Considered were FeCrAl steel (similar to Kanthal APMT), Nb-1%Zr (similar to PWC-11), and a hybrid SiC-composite with a metallic barrier layer. The niobium alloy was also seen as requiring an oxidation protective layer, and a diffusion silicide was investigated. Metallic barrier layers for the SiC-composite reviewed included a FeCrAl alloy, Nb-1%Zr, and chromium. Thermochemical calculations were performed to determine oxidation behavior of the materials in steam, and for hybrid SiC-composites possible interactions between the metallic layer and SiC. Additionally, experimental exposures of SiC-alloy reaction couples at 673K, 1073K, and 1273K for 168 h in an inert atmosphere were made and microanalysis performed. Whereas all materials were determined to oxidize under higher oxygen partial pressures in the steam environment, these varied by material with expected protective oxides forming. Finally, the computed and experimental results indicate the formation of liquid phase eutectic in the FeCrAl-SiC system at the higher temperatures.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2022

Sensitivity analyses of a homogeneous model and a RZ model of the MYRRHA reactor in its critical configuration

Two homogenized models of the MYRRHA (Multi-purpose hybrid Research Reactor for High-tech Applications) reactor in its critical configuration are presented in this study. Both models will be verified by comparing the main reactor parameters (K{sub eff}, β{sub eff} and Λ) with those of the heterogeneous model and a sensitivity analysis will be performed. A sensitivity analysis of some important parameters related to reactivity, namely the vacuum coefficient, the Doppler and the power peaking factors, is also presented. The study of the vacuum coefficient has been carried out by analyzing two possible scenarios: 50% vacuum in the coolant (lead bismuth eutectic) and 100%, obtaining a list of the 10 reactions and nuclides that most affect the k{sub eff} value. With respect to the Doppler coefficient, it will be seen that a 300 degree increase in fuel temperature (starting at 800 K) results in a reduction of the total reactivity of the system by 134 pcm.. Finally, the map of the power peaking factors will be shown, as well as a sensitivity analysis. For making the sensitivity calculations Serpent-2 reactor physics Monte Carlo code has been used and JEFF-3.3 library has been chosen in order to continue with the OECD/NEA WPEC SG46 work evaluating the nuclear data of this library. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2018

Effect of thermal annealing on microstructure evolution and mechanical behavior of an additive manufactured AlSi10Mg part

The powder-bed laser additive manufacturing (AM) process is widely used in the fabrication of three-dimensional metallic parts with intricate structures, where kinetically controlled diffusion and microstructure ripening can be hindered by fast melting and rapid solidification. Therefore, the microstructure and physical properties of parts made by this process will be significantly different from their counterparts produced by conventional methods. This work investigates the microstructure evolution for an AM fabricated AlSi10Mg part from its nonequilibrium state toward equilibrium state. Special attention is placed on silicon dissolution, precipitate formation, collapsing of a divorced eutectic cellular structure, and microstructure ripening in the thermal annealing process. These events alter the size, morphology, length scale, and distribution of the beta silicon phase in the primary aluminum, and changes associated with elastic properties and microhardness are reported. In conclusion, the relationship between residual stress and silicon dissolution due to changes in lattice spacing is also investigated and discussed.

36 MATERIALS SCIENCE↗