Search NASA⌕ Search

SEARCH · Search NASA

Results for “FRACTURE PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Integrated Experimental and Modeling Study of Geochemical Reactions of Simple Fracturing Fluids with Caney Shale

Interactions between rock minerals and hydraulic fluids directly impact the geochemical and geomechanical properties of shale formations. However, the mechanisms of geochemical reactions in shale unconventional reservoirs remain poorly understood. Here, to investigate the geochemical reactions between shale and hydraulic fracturing fluids, a series of batch reactor experiments were undertaken. Three rock samples with different mineralogical compositions and three fluid samples of different compositions (deionized water, deionized water + 2% potassium chloride (KCl), and deionized water + 0.5% choline chloride (C 5 H 14 ClNO) were used. Experiments were undertaken at reservoir temperature and atmospheric pressure. Elemental compositions of effluents after 1, 3, 7, 14, 28 days were analyzed using Inductively Couple Plasma Mass Spectrometry (ICP-MS). Medical Computed Tomography (CT) scan and X-ray Fluorescence (XRF) were conducted on the entire core run to help upscale results obtained from rock-fluid interaction experiments. Geochemical modeling using a reactive simulator, TOUGHREACT, was undertaken to corroborate experimental results. Results show that lower pH triggered high dissolution rates in the rock samples, especially the carbonate components. As pH increased, the rate of dissolution declined significantly, though for most cases dissolution still continued. Observed dissolved silica concentrations were much higher than the quartz solubility, suggesting that much of the silica originates from more soluble silica polymorphs and possibly desorption from clay mineral exchange sites. Concentration of most elemental species in solution increased but aluminium and magnesium concentrations declined rapidly following initial entry into solution. Geochemical modeling corroborated the conclusions regarding mineral dissolution and precipitation observed from experiments, notably; the dissolution of calcite and oxidation of pyrite in reacted shale samples, the likely presence of silica polymorphs such as opal, chalcedony or amorphous silica in these samples, and the reduction of Al and Mg concentrations in solution by precipitation of secondary aluminosilicate phases. The de-flocculation of clay minerals during reaction implies fines migration after hydraulic fracturing. This is detrimental to reservoir productivity as clay fines are displaces and lodged within the micro and nano-fractures created during fracturing. The immediate consumption of aluminium and magnesium also has implications on blockage of hydrocarbon pathways due to precipitation of new minerals in these locations.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2019

Forced Cooling Friction Stir Welding of 2060-T8 Al-Li Alloy

Friction stir welding of 2060-T8 Al-Li alloy was experimentally investigated. Forced cooling process was realized by placing two copper pressure plates with a waterway on both sides of weld top surface. The relations between joint formation, microstructures and mechanical properties were mainly discussed. Compared with conventional joint by natural cooling, the welding joint with smaller flashes by forced cooling has the smaller well-distributed grains and higher microhardness in the stir zone (SZ). The tensile strength and elongation of forced cooling joint, respectively, reach 445.7 MPa and 6.7%, which are obviously higher than those of the conventional joint. The fracture locations of the conventional and forced cooling joints are located in the SZ, and the fracture surface morphologies show a typical ductile fracture mode.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Numerically Testing Conceptual Models of the Utah FORGE Reservoir Using July 2023 Circulation Test Data

Over the past several years, many new data sets have become available regarding the characterization of the Utah FORGE reservoir. These include, but are not limited to, the stimulation of Well 16A, the drilling and completion of Well 16B, and interwell circulation confirmatory testing. As part of the characterization efforts, conceptual models of the reservoir are re-examined as new data become available. As part of the planning for FORGE activities, numerical models are often used to predict the reservoir response to the planned testing. Stochastic methods are often employed to bound uncertainty and allow for evaluation of comprehensive ranges of key reservoir parameters. For the most recent interwell circulation confirmatory testing (July 2023), a priori numerical model predictions did bound the observed behavior (Xinj et al., 2023), but key deviations from expected behavior prompted the FORGE team to reevaluate our conceptual model of the reservoir. In early October 2023, key members of the development, testing, and monitoring teams met for 2 days to review newly collected data and discuss ‘interesting’ or ‘key’ observations. From these discussions, 15 Key Observations were documented, with several significant ones being that the discrete fracture network developed from the 16A stimulation data may not be appropriate and that the early time pressure data obtained during the summer 2023 reservoir testing were best described using radial solutions. In July 2023, two campaigns of interwell confirmatory testing were conducted, the first set of tests occurred on July 4-5 and the second set on July 18-19. The second set of circulation tests conducted at the Utah FORGE site between the injection well 16A(78)-32 and production well 16B(78)-32 on July 18 and 19, 2023 are used to calibrate material properties in a thermal-hydraulic-mechanical (THM) simulation of the discrete fracture network connecting the wells. The spatially and temporally varying reservoir properties are calibrated to match the time dependent pressure and production profiles from the circulation tests. In future work, this calibrated model will be coupled to the native state THM model of the FORGE reservoir to predict surface deformation and strains resulting from pumping schedules.

58 GEOSCIENCES↗
DOE OSTI2024

Numerically Testing Conceptual Models of the Utah FORGE Reservoir Using July 2024 Circulation Test Data

Over the past several years, many new data sets have become available regarding the characterization of the Utah FORGE reservoir. These include, but are not limited to, the stimulation of Well 16A, the drilling and completion of Well 16B, and interwell circulation confirmatory testing. As part of the characterization efforts, conceptual models of the reservoir are re-examined as new data become available. As part of the planning for FORGE activities, numerical models are often used to predict the reservoir response to the planned testing. Stochastic methods are often employed to bound uncertainty and allow for evaluation of comprehensive ranges of key reservoir parameters. For the most recent interwell circulation confirmatory testing (July 2023), a priori numerical model predictions did bound the observed behavior (Xinj et al., 2023), but key deviations from expected behavior prompted the FORGE team to reevaluate our conceptual model of the reservoir. In early October 2023, key members of the development, testing, and monitoring teams met for 2 days to review newly collected data and discuss ‘interesting’ or ‘key’ observations. From these discussions, 15 Key Observations were documented, with several significant ones being that the discrete fracture network developed from the 16A stimulation data may not be appropriate and that the early time pressure data obtained during the summer 2023 reservoir testing were best described using radial solutions. In July 2023, two campaigns of interwell confirmatory testing were conducted, the first set of tests occurred on July 4-5 and the second set on July 18-19. The second set of circulation tests conducted at the Utah FORGE site between the injection well 16A(78)-32 and production well 16B(78)-32 on July 18 and 19, 2023 are used to calibrate material properties in a thermal-hydraulic-mechanical (THM) simulation of the discrete fracture network connecting the wells. The spatially and temporally varying reservoir properties are calibrated to match the time dependent pressure and production profiles from the circulation tests. In future work, this calibrated model will be coupled to the native state THM model of the FORGE reservoir to predict surface deformation and strains resulting from pumping schedules.

15 GEOTHERMAL ENERGY↗
DOE OSTI2016

The correlation between acoustic and magnetic properties in the long working metal boiler drum with the parameters of the electron microscope

The present paper presents comparative analysis of measurement results of acoustic and magnetic properties in long working metal of boiler drums and the results obtained by methods of electronic microscopy. The structure of the metal sample from the fracture zone to the base metal (metal working sample long) and the center of the base metal before welding (weld metal sample) was investigated by electron microscopy. Studies performed by spectral acoustic, magnetic noise and electron microscopic methods were conducted on the same plots and the same samples of long working and weld metal of high-pressure boiler drums. The analysis of research results showed high sensitivity of spectral-acoustic and magnetic-noise methods to definition changes of microstructure parameters. Practical application of spectral-acoustic and magnetic noise NDT method is possible for the detection of irregularities and changes in structural and phase state of the long working and weld metal of boiler drums, made of a special molybdenum steel (such as 20M). The above technique can be used to evaluate the structure and physical-mechanical properties of the long working metal of boiler drums in the energy sector.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Analysis of permeability change in dissolving rough fractures using depth-averaged flow and reactive transport models

Many geophysical problems and engineering applications involve fluid flow through evolving faults and fractures. These situations are typical in CO 2 injection scenarios where supercritical CO 2 or CO 2 –saturated fluids are able to dissolve the solid matrix. Dissolution or precipitation within a fracture could lead to self-reinforcing or self-limiting behavior due to feedbacks from changes in permeability (k). There is limited predictive understanding of this phenomenon. Here, we investigated the case of fracture dissolution using a two-dimensional depth-averaged reactive transport model. The model simulated an acidic fluid dissolving a three-dimensional rough fracture. We observed different dissolution patterns across a wide range of geometric properties and different Peclet and Damkohler numbers (960 cases total). Despite this variation, a persistent linear increase in k with time (t) roughly manifested once the dissolution front advanced through the fracture. The time rate of change of k (k/t) is roughly constant for all simulations. The modeled rate is consistent with a theoretical value based on the parallel plates model and with experimentally derived values. Finally, the results confirm the common presence of linear time-dependence of fracture k due to self-reinforcement.

58 GEOSCIENCES↗
DOE OSTI2020

U 3 Si 2 and UO 2 composites densified by spark plasma sintering for accident-tolerant fuels

This work reports the synthesis and characterization of the U 3 Si 2 and UO 2 composites sintered by spark plasma sintering (SPS) with controlled microstructures for accident-tolerant fuel application. The U 3 Si 2 and UO 2 composites with different silicide and oxide ratios were synthesized by SPS at temperatures from 1000 to 1300 °C for 5 minutes. The microstructure and phase composition of the SPS densified composite fuels were characterized with scanning electron microscopy, X-ray diffraction (XRD), and energy dispersed spectroscopy (EDS). A systematic study of the thermal and mechanical properties was conducted using microhardness testing and laser flash apparatus, along with oxidation resistance measurements using thermogravimetric analysis (TGA). The results show that the synthesis of composite fuels can be achieved with a 90% theoretical density (TD) at 1000 °C and over 95% TD when sintered at 1300 °C. XRD and EDS results confirmed that the dominant phases in the composites are U 3 Si 2 and UO 2 . Improved physical density generally leads to improved hardness, fracture toughness, thermal diffusivity, and onset temperature during the oxidation process. U 3 Si 2 was found to play a dominant role in determining the mechanical and oxidation properties of the composite fuels, whereas UO 2 had a more important impact on controlling the thermal diffusivity of the composites. The composite with 50 wt% UO 2 sintered at 1300 °C displayed the onset oxidation temperature of 500 °C by dynamic oxidation testing using TGA at a ramp degree of 10 °C/min. The composite also achieved a high fracture toughness of ~3.5 MPa m ½ . Finally, these results highlight the potential of composite fuel forms densified by SPS with simultaneously enhanced fissile element density, fracture toughness, thermal transport properties, and oxidation resistance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Ductile-Phase Toughened Tungsten for Plasma Facing Materials (Final Report)

Tungsten (W) and W-alloys are the leading candidates for plasma-facing components in nuclear fusion reactors because of their high melting point, high temperature strength, good thermal conductivity and low sputtering yield, however, they are too brittle to serve a structural function. A variety of processing approaches were employed to fabricate ductile-phase-toughened (DPT) tungsten (W) composites, that includes consolidating elemental W powder with Cu- or WC-coated W-wires via spark plasma sintering (SPS). Laminated W-composites with Cu-foils were also fabricated by hot-pressing or brazing. Mechanical testing and analytical modeling were used to guide composite development. The fracture toughness of thin W plate or laminated W-composites was measured in three-point bending (3PB) at room temperature (RT). Crack arrest and crack bridging were observed for the laminated composites, and fracture resistance curves were successfully calculated. An analytical model of crack bridging was developed using the specimen geometry, matrix properties, and the stress-displacement function of a ductile reinforcement (“bridging law”) to calculate the fracture resistance curve (R-curve) and load-displacement curve (P-D curve) for any test specimen geometry. The code was also implemented to estimate the bridging law of an arbitrary composite using R-curve data. In another approach, commercially available liquid-phase sintered W alloys with four different compositions were characterized in terms of microstructure, tensile and fracture toughness at different specimen, size, geometry and testing temperatures. The room temperature (RT) average maximum load fracture toughness values (KIc or KJm ≈ 38 to 107 MPa√m) of WHA, containing only 3 to 10 wt.% of a NiFe-based ductile phase (DP), are ≈ 5 to 13 times higher than for monolithic W (≈ 8 MPa√m). Most RT tests show extensive stable ductile tearing (DT) at all W contents, including 97W (KJm ≈ 69 MPa√m), for small baseline bend bars (B=1.65mm, W=2B). Exceptions to DT, include RT elastic fracture at 97W observed in 3x larger specimens than the baseline specimens. However, the WHA KIc was still almost 5 times higher than that for monolithic W. The other exception to RT ductile tearing was for some of the 6 to 8x larger 95W alloy specimens that contained large ceramic initiating inclusions at the precrack front, along with lower DP%, with a KIc ≈ 59 MPa√m, compare to their stable DT KJm ≈ 82 MPa√m. Small specimen tests down to -196°C, to partially emulate irradiation hardening, also transition to elastic fracture at a temperature (-150 for 90W to -25ºC for 97W) that depends on the W content. However, even at -196°C, the KIc at 97W is ≈ 3 times that of monolithic W at RT. In contrast to classical ductile phase toughening by macrocrack bridging, WHA toughening mainly involves new mechanisms associated with arrest, blunting and bridging of numerous process zone microcracks. Later, these WHAs were used to fabricate W-WHA hybrid composites by coating elemental W powder on WHA using SPS. Three-point bend bars were fabricated and fracture toughness was tested at room temperature. Crack initiated and propagated from W-part to the WHA part for the well-bonded (interface) W-WHA composites for 90 and 92.5WHAs, however, crack arrested and diverted at/or through the interface for loosely bonded W-95/97WHAs with increasing load.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Sequential Fracture Activation and Stress Evolution During EGS Stimulation at Utah FORGE Revealed by Waveform Cross‐Correlation

Mapping fracture networks in Enhanced Geothermal Systems (EGS) is essential for optimizing reservoir performance, yet complex fracture evolution during stimulation remains difficult to resolve. This study examines the evolution of microseismicity and fracture networks during stage 3 of the 2022 EGS stimulation at the Utah Frontier Observatory for Research in Geothermal Energy site. We map the fracture network represented by 20 clusters of seismic events identified by waveform similarities with cross-correlation. We characterize their geometric properties such as strike, dip, length, and width, and analyze the time evolution of activated fractures. The results reveal a systematic fracture evolution: early activation of pre-existing natural fractures, complex network development during peak injection, and continued activation of less favorably oriented fractures post-injection. Magnitude calibration using the Principal Component Analysis of cross-correlated waveforms improves relative amplitude measurements, refining estimations of the Gutenberg-Richter b-values with spatial variations in b-values suggesting stress re-distribution across the stimulated area. Analysis of the stress state of selected fractures further shows that fractures requiring higher excess pore pressure primarily activate at the end of injection and post-injection, highlighting stress transfer due to pore pressure as a dominant triggering mechanism. These findings provide insights into fracture propagation, stress evolution, and seismic hazard assessment in EGS reservoirs.

Asirifi, Richard [Texas A & M Univ., College Stati↗
NASA NTRS1975

Fundamental analysis of the failure of polymer-based fiber reinforced composites

A mathematical model predicting the strength of unidirectional fiber reinforced composites containing known flaws and with linear elastic-brittle material behavior was developed. The approach was to imbed a local heterogeneous region surrounding the crack tip into an anisotropic elastic continuum. This (1) permits an explicit analysis of the micromechanical processes involved in the fracture, and (2) remains simple enough to be useful in practical computations. Computations for arbitrary flaw size and orientation under arbitrary applied loads were performed. The mechanical properties were those of graphite epoxy. With the rupture properties arbitrarily varied to test the capabilities of the model to reflect real fracture modes, it was shown that fiber breakage, matrix crazing, crack bridging, matrix-fiber debonding, and axial splitting can all occur during a period of (gradually) increasing load prior to catastrophic failure. The calculations also reveal the sequential nature of the stable crack growth process proceding fracture.

Kanninen, M. F.↗
DOE OSTI2022

A New Model for Simulating the Imbibition of a Wetting-Phase Fluid in a Matrix-Fracture Dual Connectivity System

The imbibition experiment is an effective approach for measuring petrophysical properties of porous media, with many such experiments performed over the past decade. Quite some empirical, analytical, and numerical models have been developed to simulate spontaneous imbibition of the wetting phase fluid into porous media, but limitations still exist. In previous studies, the imbibition process has been considered to give a piston-like displacement or the porous medium modeled as multiply-sized pores linked with bonds; both approaches fail to yield comprehensive results due to their neglect of the presence of irregular fractures or nonuniform flow paths through the matrix. By building a numerical model for simulating laboratory-scale experimental data, we performed imbibition tests on several fractured Barnett Shale samples having fractures either parallel ( P ) or transverse ( T ) to the bedding plane and used MATLAB to build a new numerical model by combining the imbibition process in fractures and the matrix using concepts from percolation theory. The experimental data show that the rocks with P -direction fractures have a more steady increase of imbibition rates than the case of T -direction one. As the shale matrix with low pore connectivity hampers the upward water movement, the imbibition rate of shales with T -direction fractures will decrease suddenly after the bottom layer in contact with water is saturated during the initial period. This wetting phase movement (WPM) model can simulate 3D porous media with 2D fractures. The rate of imbibition by fractured porous media is associated with physical parameters such as porosity and fracture distribution (e.g., the number and angle of fractures). Using Monte Carlo methods, we examined fracture parameters and predicted elapsed time and cumulative water imbibition, for the Barnett Shale samples. The results show that the rate of imbibed water mass is sensitive to the number of fractures directly connected to water source, and the connectivity between two neighboring grid cells is a key parameter for the wetting-front progression. The findings of this study can help to better understand the imbibition process with multiple influencing processes and factors in fractured-matrix rocks. Although the experiments, data simulation, and prediction results are based only on Barnett Shale samples, the model is readily applicable to imbibition tests of other fractured rocks to show the spatial and temporal behavior during a dynamic imbibition process that are not easily captured experimentally.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

An embedded-atom method potential parameterized for sulfur-induced embrittlement of nickel

The embrittling or strengthening effect of solute atoms at grain boundaries (GBs), commonly known as the embrittling potency, is a necessary thermodynamic property for characterizing the effects of solute segregation on GB fracture. One of the more technologically relevant material systems related to embrittlement is the Ni–S system where S has a deleterious effect on fracture behavior in polycrystalline Ni. Here, we develop a Ni–S embedded-atom method (EAM) interatomic potential that accounts for the embrittling behavior of S at Ni GBs. Results using this new interatomic potential are then compared to previous density functional theory studies and a reactive force-field potential via a layer-by-layer segregation analysis. Our potential shows strong agreement with existing literature and performs well in predicting properties that are not included in the fitting database. Finally, we calculate embrittling potencies and segregation energies for six [100] symmetric-tilt GBs using the new EAM potential. We observe that embrittling potency is dependent on GB structure, suggesting that specific GBs are more susceptible to sulfur-induced embrittlement.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The effect of Ni doping on the mechanical behavior of tungsten

The effect of nickel (Ni) on activated sintering of tungsten has been known and investigated for decades. However, there are few reports on the mechanical properties of tungsten when Ni is added as a low alloying additive with less than 1 wt%. In this work, the mechanical behaviors of tungsten doped with 0.2–1.0 wt% nickel from room temperature up to 400 °C were investigated. The results show that the compression ductility of as-sintered Ni doped tungsten is drastically higher than that of as-sintered pure tungsten at all tested temperatures including room temperature, and the fracture toughness at room temperature is increased by 92%. The results suggest that the ductile-to-brittle transition temperature (DBTT) of tungsten can be reduced substantially by doping with Ni.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Possible role of crustal flexure in the initial detachment of extensional allochthons

The existence of low-angle normal faults indicates that the ratio of shear stress (TAU) to normal stress (sigma sub N) needed to cause slip on faults is substantially less than would be predicted based on experimental data. Because the tensional strength of rock at a large scale is exceedingly low, the upper plate of a low-angle normal fault cannot be pulled down the fault ramp, but must be driven down it by its own weight. The active or recently active Sevier Desert detachment fault in western Utah dips regionally at 12 deg. The radio of shear stress to normal stress due to the weight of the upper plate on a 12 deg dipping fault surface is 0.2. In contrast, laboratory experiments indicate that slip on fracture surfaces occurs with almost all rock types when (tau/sigma) reaches values of 0.6 to 0.85, corresponding to normal-fault dips of 30 deg to 40 deg. Seismological data indicate that low deviatoric stresses are associated with movement on faults of other geometrics and are not unique to low-angle normal faults. It thus appears that approximately planar fault zones with surface areas of hundreds to thousands of square kilometers have different mechanical properties than would be predicted based on laboratory studies of fractured rock. Modeling of stresses indicates that deviatoric stresses greater than 5kb exist and are sustainable in oceanic lithosphere, and that failure occurs when tau/sigma sub N approaches 0.6 to 0.85.

Spencer, J. E.↗
DOE OSTI2021

Creep Behavior of a High-$\gamma^{\prime}$ Ni-Based Superalloy Fabricated via Electron Beam Melting

Additive manufacturing enables the fabrication of complex engineering components previously inaccessible through traditional processes. Nickel-base superalloys with large γ' volume fraction are typically considered non-weldable and therefore exhibit a propensity for cracking during the fusion process. These crack-prone materials, however, are of great importance in gas turbine engines due to their excellent high temperature creep resistance. In this study we investigate the creep behavior of IN738LC produced by the electron beam melting process. Here, we find that with appropriate post-build heat treatment the creep response of material oriented in the build direction exhibits deformation and rupture behavior comparable to that of conventionally cast IN738 & IN738LC. In the transverse direction properties fall below the expected cast behavior, however, we argue this is likely due to differences in grain scale and crystallographic texture. It may be possible to coarsen the grain morphology with appropriate process-parameter optimization in order to reduce the severity of intergranular fracture in the transverse direction. These results illustrate that high temperature properties exhibited by additively manufactured IN738LC are suitable for the hot section of gas turbine engines.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Emergency core cooling system performance criteria for Multi-Layered Silicon Carbide nuclear fuel cladding

Multi-layered Silicon Carbide (SiC) cladding has been proposed to replace the current Zircaloy (Zr) cladding in existing nuclear power plants. Due to its ceramic property, SiC may have a different failure mechanism from that of metallic Zr clad. This characteristic should be considered in designing the plant’s safety system performance, such that the fuel’s integrity is reasonably assured during accident scenarios. This paper aims at optimizing the Emergency Core Cooling System (ECCS) performance criteria in mitigating LBLOCA accidents at a Pressurized Water Reactor (PWR) using the uranium dioxide fuel and duplex or triplex SiC cladding structures. Clad failures by brittle fractures and thermal degradation were modeled in a fuel analysis code. This fuel model was coupled with the RELAP5 plant model by adapting the fuel’s mesh configuration and formulating the effective heat transfer coefficients. A model to quantify the likelihood of clad functional failure as a combination of individual layer fractures at various axial positions was proposed. Updated SiC material properties were gathered from recent reference studies. Clad reliability estimates using the proposed model were compared with the estimates obtained using other models. The results were used to relax the criterion of required actuation timing of ECCS, such that the risk of the new plant design is less or equal to that of the initial plant configuration. Triplex clad was more reliable than duplex clad and Zr, reducing the conditional core damage probability by three orders of magnitude in the reference LBLOCA scenario. Compressive stresses due to irradiation swelling played the determining role in the vulnerabilities of each clad design. The duplex clad was vulnerable to pressure-loading stresses while triplex clad was prone to fail due to thermal shocks experienced during the LOCA reflood phase. Additionally, it was concluded that the most vulnerable axial fuel rod location in the reference LBLOCA scenario was located at the highest axial power peaking location. A sensitivity study on the ECCS timing density was conducted. The results showed that ECCS actuation timing could be extended from the initial technical specification, without increasing the fuel damage likelihood. The time extension was distributed in the order of several hundreds of seconds, which was comparable with time extensions offered by FeCrAl and Cr-coated-Zr clad designs in LBLOCA scenarios. This time extension may potentially reduce the failure probabilities of EDGs and pumps, hence improving the plant safety further.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1984

Space Radiation Effects on Graphite-Epoxy Composite Materials

Radiation effects on engineering properties, dimensional stability, and chemistry on state of the art composite systems were characterized. T300/934 graphite-epoxy composite was subjected to 1.0 MeV electron radiation for a total dose of 1.0 x 10(10) rads at a rate of 5.0 x 10(7) rads/hour. This simulates a worst case exposure equivalent to 30 years in space. Mechanical testing was performed on he 4-ply unidirectional laminates over the temperature range of -250 F (116K) to +250 F (394K). A complete set of in-plane tensile elastic and strength properties were obtained (E sub 1, E sub 2, nu sub 12, G sub 12, X sub T, Y sub T, and S). In addition electron microscopy was used to study and analyze the fracture surfaces of all specimens tested. Results indicate that little difference in properties is noted at room temperature, but significant differences are observed at both low and elevated temperatures.

Milkovich, S. M.↗
DOE OSTI2019

Solderability of AZ31B Magnesium Alloy Coated by Copper and Strength of the Solder Joints

Magnesium alloys are promising as light materials, while their high chemical reactivity makes them difficult to be soldered. In this study, the AZ31B alloy was pretreated by zincification and coated by an electrodeposited Cu layer, and then soldered with Sn-58Bi solder in air furnace. The microstructure and properties of the AZ31B/Cu(Zn)/SnBi solder joints were characterized to evaluate the solderability of the Cu-coated Mg alloy and the influence of soldering on the Cu coating. It was found that the Cu coating is dense, and little defect exists along the Cu(Zn)/AZ31B interface. The soldering process has little negative effect on the bonding between the Cu coating and the AZ31B substrate, and the AZ31B/Cu(Zn)/SnBi solder joints of high metallurgical quality were obtained. Tensile fracture of the solder joint occurs mainly in the solder, with no peeling of the Cu coating. Under shear loading, cracks initiate inside the SnBi solder and the final fracture of the joint occurs around the Cu{sub 6}Sn{sub 5}/solder interface or along the Cu(Zn)/AZ31B interface. The tensile and shear strength of the AZ31B/Cu(Zn)/SnBi solder joints are close to that of the SnBi/Cu solder joints. It is demonstrated that the Cu-coated Mg alloy shows superior solderability and can be soldered by the Sn-based low-melting solder in air.

36 MATERIALS SCIENCE↗