Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fast Fourier transform”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Response characteristics of stable mixed-potential NH 3 sensors in diesel engine exhaust

Here, a mixed-potential, electrochemical sensor platform is extended to NH 3 sensing by the introduction of a new gold alloy working electrode. A planar, pre-commercial NH 3 sensor utilized LANL’s controlled interface approach, and a Pd-Au alloy working electrode was tested in exhaust of a GM 1.9 L diesel engine downstream of a diesel oxidation catalyst through a slipstream arrangement. A fraction of the exhaust was pulled across the sensor with a pump at 20 L/min. In order to simulate NH 3 slip inside of a full SCR emissions control system, NH 3 was injected immediately upstream of the sensor using a calibrated mass flow controller. The sensor response quantitatively tracked the NH 3 as measured via Fourier transform infrared (FTIR) analyzer. A calibration curve was obtained in the exhaust from an ammonia staircase response with the engine running at steady-state engine conditions resulting in low background concentrations of NO x and HC (<20 ppm) during calibration. Exhaust gas recirculation (EGR) switching and sweeps were used to evaluate the NH 3 sensor response under different amounts of total background NO x . The calibration curve was used to directly compare the [NH 3 ] calculated from sensor response to the gas phase composition measured via FTIR. In general, there was excellent quantitative agreement between the sensor response and the actual NH 3 in the exhaust gas, and fast response time such that transients (<5 ppm) could be easily discerned from baseline. A LANL pre-commercial NO x sensor was tested simultaneously with the NH 3 sensor and the extent of cross-sensitivity between the two sensors will be discussed.

47 OTHER INSTRUMENTATION↗

Effect of Cobalt Oxide Nanoparticles on the Nano-scale Free Volume and Optical Properties of Biodegradable CMC/PVA Films

Chemically prepared cobalt oxide nanoparticles (NPs) were added to biodegradable carboxymethyl cellulose (CMC) (20%)/polyvinyl alcohol (PVA) (80%) blend films. The structural properties of these films were investigated by X-ray diffraction, Fourier transformation infrared spectroscopy (FTIR) and differential thermal analysis (DTA). Co{sub 3}O{sub 4}/(CMC + PVA) films show a semi-crystalline structure and the degree of crystallinity decreases with adding Co{sub 3}O{sub 4} NPs. FTIR confirms the good interaction between the blend chains and Co{sub 3}O{sub 4} NPs. The melting temperature T{sub m} for CMC/PVA is about 212 °C then decreased with increasing Co{sub 3}O{sub 4} content, due to some decrease in the ordered association of the blend which results in a decrease in the blend crystallinity. Positron annihilation lifetime spectroscopy (PALS) measurements were carried out with a conventional fast–fast coincidence spectrometer. It was found that ortho-positronium lifetime τ{sub 3} and free volume V{sub f} increase while o-Ps intensity I{sub 3} still constant as Co{sub 3}O{sub 4} concentration increases. This is because adding Co{sub 3}O{sub 4} NPs encourages the formation of o-Ps. The swelling ratio SR% as a function of Co{sub 3}O{sub 4} concentration was also studied and its value increases with Co{sub 3}O{sub 4} addition. The optical study illustrated the decrease of the transmittance T of the films from 87 to 35.5% with increasing Co{sub 3}O{sub 4} content from 0 to 0.9 wt%. Also, both the direct and indirect optical band gaps of the films red-shifted from 4.05 to 3.75 eV and 3.3 to 2.75 eV, respectively. The influence of Co{sub 3}O{sub 4} on the refractive index of the films is also reported.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Metasomatic Control of Water in Garnet and Pyroxene from Kaapvaal Craton Mantle Xenoliths

Fourier transform infrared spectrometry (FTIR) and laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS) were used to determine water, rare earth (REE), lithophile (LILE), and high field strength (HFSE) element contents in garnet and pyroxene from mantle xenoliths, Kaapvaal craton, southern Africa. Water enters these nominally anhydrous minerals as protons bonded to structural oxygen in lattice defects. Pyroxene water contents (150-400 ppm in clinopyroxene; 40-250 ppm in orthopyroxene) correlate with their Al, Fe, Ca and Na and are homogeneous within a mineral grains and a xenolith. Garnets from Jagersfontein are chemically zoned for Cr, Ca, Ti and water contents. Garnets contain 0 to 20 ppm H2 Despite the fast diffusion rate of H in mantle m inerals, the observations above indicate that the water contents of mantle xenolith minerals were not disturbed during kimberlite entrainment and that the measured water data represent mantle values. Trace elements in all minerals show various degrees of light REE and LILE enrichments indicative of minimal to strong metasomatism. Water contents of peridotite minerals from the Kaapvaal lithosphere are not related to the degree of depletion of the peridotites. Instead, metasomatism exerts a clear control on the amount of water of mantle minerals. Xenoliths from each location record specific types of metasomatism with different outcomes for the water contents of mantle minerals. At pressures . 5.5 GPa, highly alkaline melts metasomatized Liqhobong and Kimberley peridotites, and increased the water contents of their olivine, pyroxenes and garnet. At higher pressures, the circulation of ultramafic melts reacting with peridotite resulted in co-variation of Ca, Ti and water at the edge of garnets at Jagersfontein, overall decreasing their water content, and lowered the water content of olivines at Finsch Mine. The calculated water content of these melts varies depending on whether the water content of the peridotite (2 wt% HO. 2O) or individual m inerals (<0.5-13 wt% H2O) are used, and also depend on the mineral-melt water partition coefficients. These metasomatic events are thought to have occurred during the Archean and Proterozoic, meaning that the water contents measured here have been preserved since that time and can be used to investigate viscocity and longevity of cratonic mantle roots.

Peslier, Anne H.↗

Interligand Coupling Drives Fast Triplet Energy Transfer Routes in PbS/Tetracene Quantum Dot Hybrids

The binding of photoactive organic ligands to inorganic quantum dots (QDs) creates a versatile hybrid architecture that allows access to photophysical processes such as efficient triplet exciton generation with near-infrared radiation. Here we report the subnanosecond generation of a hybrid triplet state with mixed ligand-QD character by replacing native oleate ligands on small PbS QDs with 5,12-tetracenepropiolic acid, a bifunctional ligand with two carboxylic acids that tends to lie face-on with the QD surface at low loadings. The face-on geometry engenders a regime of strong electronic coupling that is evident in steady-state absorption and hastens triplet energy flow by several orders of magnitude compared with more typical tetracene-based ligands exhibiting weak coupling. We further determined via Fourier transform infrared (FTIR) and supported by density functional theory (DFT)-based geometry optimizations that high ligand loading causes a shift in QD-ligand mutual disposition toward an edge-on geometry that instigates the formation of intermolecular excited states characterized by triplet excimer-like features in photoluminescence and transient absorption. Our results demonstrate the ability to control strongly coupled ligand-QD systems toward ultrafast generation of photophysically relevant species such as triplets that are valuable for photon upconversion and catalysis.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Spectral Proper Orthogonal Decomposition of uPSP Measurements in Recent NASA Ames Wind Tunnel Test

This paper discusses Spectral Proper Orthogonal Decomposition (SPOD) of the Unsteady Pressure-Sensitive Paint (uPSP) measurements in recent NASA Ames wind tunnel test. The uPSP measurements were collected using Innovative Scientific Solutions, Inc. (ISSI) porous, fast-response pressure-sensitive paint, 40 ISSI four-inch air-cooled Light-Emitting Diodes, and 8 Phantom v2512 high-speed cameras at 10,000 frames per second in the uPSP Launch Vehicle Demonstration Test (LVDT) of the Space Launch System (SLS) vehicle in the 11-by 11-foot transonic test section of the Unitary Plan Wind Tunnel at NASA Ames Research Center in April 2024. SPOD is derived from a space-time proper orthogonal decomposition problem for statistically stationary flows. SPOD modes are determined in the frequency domain. Each SPOD mode oscillates at a single frequency. SPOD can be viewed as an extension of the Discrete Fourier Transform composition and the Dynamic Mode Decomposition. In this paper, the outputs of SPOD of the uPSP measurements in the uPSP LVDT are presented and the effectiveness of SPOD in the identification, diagnosis and analysis of the aerodynamic and aeroacoustic phenomena is demonstrated. The unsteady and dynamic property of the pressure field on the surface of the SLS Block 1B crew vehicle is presented with the visualization of the SPOD modes of the uPSP measurements in the tests of a Mach sweep run of the uPSP LVDT. The SPOD outputs were generated with the execution in parallel of a code in Python, with the library of Message Passing Interface for parallel processing, on the NASA Pleiades supercomputer. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities Portfolio Office.

Aeroacoustics↗

Improved electrochemical and thermal performances of layered Li[Li 0.2 Ni 0.17 Co 0.07 Mn 0.56 ]O 2 via Li 2 ZrO 3 surface modification

We successfully coated a conductive Li 2 ZrO 3 layer on the surface of Li-rich layered cathode Li[Li 0.2 Ni 0.17 Co 0.07 Mn 0.56 ]O 2 in order to enhance its electrochemical performances. For the crystal structures, electrochemical properties and thermal stabilities of the bare and coated materials are studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM), electron diffraction spectroscopy (EDS), inductively coupled plasma (ICP), galvanostatic cycling, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). We found that the electrochemical performances of Li-rich cathode material are obviously improved by Li 2 ZrO 3 surface modification. Especially, the 1 wt.% Li 2 ZrO 3 -coated material demonstrates the best cycling performance, with capacity retention of 89% after 50 cycles, much better than that of the pristine one, 64%. Intensive explorations indicate that the improved electrochemical properties can be attributed to the Li 2 ZrO 3 surface layer, which not only stabilizes the cathode structure by decreasing the loss of oxygen, but also protects the Li-rich cathode material from side reaction(s) with the electrolyte and thus suppressing the fast growth of solid electrolyte interface (SEI) film on the surface of oxide particles.

25 ENERGY STORAGE↗

Behavior of sheet-like crystalline ammonium trivanadate hemihydrate (NH{sub 4}V{sub 3}O{sub 8}×0.5H{sub 2}O) as a novel ammonia sensing material

This work reports the use of ammonium trivanadate hemihydrate (NH{sub 4}V{sub 3}O{sub 8}×0.5H{sub 2}O) as a novel sensing material for ammonia resistive sensors. It was prepared by a simple and fast hydrothermal method from V{sub 2}O{sub 5} as a precursor and characterized by SEM, FT-IR, XRD and TG techniques. The as-synthesized material showed a sheet-like morphology and was found thermally stable up to 250–280 °C. It reacted promptly and irreversibly when exposed to ammonia at room temperature. A full reversibility was instead registered undergoing the formed ammonia adduct at a temperature higher than 200 °C. A NH{sub 4}V{sub 3}O{sub 8}×0.5H{sub 2}O-based resistive gas sensor was fabricated and its sensing properties were evaluated. Experimental results obtained have given a preliminary demonstration of the feasibility of using NH{sub 4}V{sub 3}O{sub 8}×0.5H{sub 2}O as a novel ammonia sensing material since it yields several advantages including easy synthesis of the sensing layer, good sensitivity and reproducibility and fast response. - Graphical abstract: Sheet-like morphology of the synthesized trivanadate hemihydrate (NH{sub 4}V{sub 3}O{sub 8}×0.5H{sub 2}O). Inset: Its electrical response to different ammonia concentrations in air. - Highlights: • A simple hydrothermal method for the fast synthesis of trivanadate hemihydrate (NH{sub 4}V{sub 3}O{sub 8}×0.5H{sub 2}O) is reported. • Sheet particles could be obtained. • A preliminary demonstration of the feasibility of using NH{sub 4}V{sub 3}O{sub 8}×0.5H{sub 2}O as a novel ammonia sensing material is presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Zinc Speciation and Propane Dehydrogenation in Zn/H-ZSM-5 Catalysts

Zn/H-ZSM-5 catalysts have been frequently investigated for propane dehydrogenation (PDH); however, the active site remains unresolved due to the complexity of the system. We employed in situ FTIR spectroscopy and a kinetics method to correlate the Zn speciation and PDH activity in Zn/H-ZSM-5 with two Si/Al ratios (15 and 39) and a range of Zn/Al ratios (0–1.7). Incremental additions of zinc show that Zn 2+ sites are preferentially formed on H-ZSM-5 over a fraction of paired Al sites followed by [Zn-O-Zn] 2+ and [ZnOH] + sites and then ZnO x clusters. The [Zn-OH] + and [Zn-O-Zn] 2+ sites in H-ZSM-5 are more active and selective than isolated Zn 2+ for PDH. [Zn-OH] + species sublimate over time on stream, leading to catalyst deactivation, while [Zn-O-Zn] 2+ species are stable even after high-temperature reduction (750 °C for 60 min). Three distinct Zn sites ([Zn-O-Zn] 2+ , Zn 2+ , and [ZnOH] + ) show a similar propane reaction order (close to 1) and H 2 reaction order (close to 0). Combined with the lack of Zn hydride when propane flows over the catalyst at 550 °C, it is concluded that propane adsorption and dissociation is a rate-determining step and H 2 desorption is fast. This work indicates that the preparation of H-ZSM-5 with abundant Al pairs may be a strategy to form stable and selective Zn/H-ZSM-5 catalysts for propane dehydrogenation. Furthermore, it is also highlighted that examining the effect of both metal/Al ratios and Al distribution of the zeolite is crucial in identifying the metal cations in metal–zeolite systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Collective Summary of sCO2 Materials Development (Supercritical Transformational Electric Power Generation (STEP) Level 2 Milestone Report) (Parts I - II)

Polymers such as PTFE (polytetrafluorethylene or Teflon), EPDM (ethylene propylene diene monomer) rubber, FKM fluoroelastomer (Viton), Nylon 11, Nitrile butadiene (NBR) rubber, hydrogenated nitrile rubber (HNBR) and perfluoroelastomers (FF_202) are commonly employed in super critical CO 2 (sCO2) energy conversion systems. O-rings and gaskets made from these polymers face stringent performance conditions such as elevated temperatures, high pressures, pollutants, and corrosive humid environments. In FY 2019, we conducted experiments at high temperatures (100°C and 120°C) under isobaric conditions (20 MPa). Findings showed that elevated temperatures accelerated degradation of polymers in sCO2, and that certain polymer microstructures are more susceptible to degradation over others. In FY 2020, the focus was to understand the effect of sCO2 on polymers at low (10 MPa) and high pressures (40 MPa) under isothermal conditions (100°C). It was clear that the same selectivity was observed in these experiments wherein certain polymeric functionalities showed more propensity to failure over others. Fast diffusion, supported by higher pressures and long exposure times (1000 hours) at the test temperature, caused increased damage in sCO2 environments to even the most robust polymers. We also looked at polymers under compression in sCO2 at 100°C and 20 MPa pressure to imitate actual sealing performance required of these materials in sCO2 systems. Compression worsened the physical damage that resulted from chemical attack of the polymers under these test conditions. In FY 2021, the effect of cycling temperature (from 50°C to 150°C to 50°C) for polymers under a steady sCO2 pressure of 20 MPa was studied. The aim was to understand the influence of cycling temperatures of sCO2 for typical polymers under isobaric (20 MPa) conditions. Thermoplastic polymers (Nylon, and PTFE) and elastomers (EPDM, Viton, Buna N, Neoprene, FF202, and HNBR) were subjected to 20 MPa sCO2 pressure for 50 cycles and 100 cycles in separate experiments. Samples were extracted for ex-situ characterization at 50 cycles and upon the completion of 100 cycles. Each cycle constituted of 175 minutes of cycling from 50°C to 150°C. The polymer samples were examined for physical and chemical changes by Dynamic Mechanical and Thermal Analysis (DMTA), Fourier Transform Infrared (FTIR) spectroscopy, and compression set. Density and mass changes immediately after removal from test were measured for degree of swell comparisons. Optical microscopy techniques and micro computer tomography (micro CT) images were collected on select specimens. Evaluations conducted showed that exposures to super-critical CO2 environments resulted in combinations of physical and/or chemical changes. For each polymer, the dominance of cycling temperatures under sCO2 pressures, were evaluated. Attempts were made to qualitatively link the permanent sCO2 effects to polymer micro- structure, free volume, backbone substitutions, presence of polar groups, and degree of crystallinity differences. This study has established that soft polymeric materials are conducive to failure in sCO2 through mechanisms of failure that are dependent on polymer microstructure and chemistry. Polar pendant groups, large atom substitutions on the backbone are some of the factors that are influential structural factors.

36 MATERIALS SCIENCE↗

Analyzing data from a PDV microphone

Photon Doppler Velocimetry (PDV) is used at Los Alamos National Laboratory to measure extremely fast velocities (on the order of 0.01 - 5 km/s) of projectiles during material testing procedures. This kind of testing is extremely important to understand how materials behave in extreme conditions (such as in nuclear explosions). PDV data is created by summing an incident beam with a Doppler shifted reflection, forming a beat frequency. The beat frequency is directly proportional to the velocity of the reflecting surface. We explored a new way of using PDV: measuring slow velocities (less than 1 m/s). The principle method we used was to measure vibrations in a Mylar sheet due to incident sound waves. I analyzed these files using both my own coding as well as a program designed at NSTec for this purpose. Analysis included performing Fourier Transforms, extracting velocity as a function of time, and playing the velocity function through a speaker to recreate the initial sound. We were able to create a successful microphone, though playback quality was poor. The limiting factor was the low velocity of the Mylar sheet, which was about 0.2 m/s. Other methods are now being explored to extract velocity data in a more efficient manner. During this project I gained extensive experience in programming, data analysis, problem solving, and communication. I learned that one must be creative in order to solve complex problems, approaching them from various angles. I also gained a lot of practice working on a team, which consisted of a high school student, another college intern, and our mentor.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Charge Retention by Organometallic Dications on Self-Assembled Monolayer Surfaces

Charge retention by mass-selected ruthenium trisbipyridine dications, or Ru(bpy)32+, soft-landed onto self-assembled monolayer (SAM) surfaces of 1H, 1H, 2H, 2H-perfluorodecane-1-thiol (FSAM), 11-mercaptoundecanoic acid (COOH-SAM), and 11-amino-1-undecanethiol (HSAM) on gold was examined using in situ time-resolved secondary ion mass spectrometry in a Fourier transform ion cyclotron resonance apparatus (FT-ICR SIMS). FT-ICR SIMS analysis was performed during ion soft-landing and for 8–15 hours after the ion beam was switched off. Our results demonstrate efficient retention of the doubly charged precursor ion on the FSAM and COOH-SAM surfaces manifested by the abundant Ru(bpy)32+ ions in the SIMS spectra. In contrast, only the singly charged Ru(bpy)3+ and Ru(bpy)2+ ions were observed on HSAM, indicating rapid loss of at least one charge by the deposited dications. The signal of Ru(bpy)32+ on COOH-SAM remained almost constant for more than 8 hours after the end of ion soft-landing, while a relatively fast decay followed by a plateau region was observed on the FSAM surface. However, we found that SIMS analysis of Ru(bpy)32+ ions soft-landed onto FSAM is complicated by facile ion-molecule reactivity occurring either on the surface or in the SIMS plume, making it difficult to accurately measure the charge reduction kinetics. Efficient retention of the doubly charged Ru(bpy)32+ ions on COOH-SAM is remarkably different from facile neutralization of protonated peptides deposited onto this surface reported in previous studies. Our results indicate different mechanisms of charge reduction of protonated molecules and permanent ions, such as Ru(bpy)32+, on SAM surfaces. Thus, we propose that proton loss is the major charge reduction channel for the protonated species, while electron transfer through the insulating SAM is responsible for the charge loss by permanent ions. Fundamental understanding of charge reduction phenomena is essential for controlled preparation of catalytically active substrates using ion soft-landing.

charge reduction↗

Universal Fourier Attack for Time Series

A wide variety of adversarial attacks have been proposed and explored using image and audio data. These attacks are notoriously easy to generate digitally when the attacker can directly manipulate the input to a model, but are much more difficult to implement in the real-world. In this paper we present a universal, time invariant attack for general time series data such that the attack has a frequency spectrum primarily composed of the frequencies present in the original data. The universality of the attack makes it fast and easy to implement as no computation is required to add it to an input, while time invariance is useful for real-world deployment. Additionally, the frequency constraint ensures the attack can withstand filtering. We demonstrate the effectiveness of the attack in two different domains, speech recognition and unintended radiated emission, and show that the attack is robust against common transform-and-compare defense pipelines.

97 MATHEMATICS AND COMPUTING↗

Universal Fourier Attack for Time Series

A wide variety of adversarial attacks have been proposed and explored using image and audio data. These attacks are notoriously easy to generate digitally when the attacker can directly manipulate the input to a model, but are much more difficult to implement in the real world. In this paper we present a universal, time invariant attack for general time series data such that the attack has a frequency spectrum primarily composed of the frequencies present in the original data. The universality of the attack makes it fast and easy to implement as no computation is required to add it to an input, while time invariance is useful for real world deployment. Additionally, the frequency constraint ensures the attack can withstand filtering defenses. We demonstrate the effectiveness of the attack on two different classification tasks through both digital and real world experiments, and show that the attack is robust against common transform-and-compare defense pipelines.

97 MATHEMATICS AND COMPUTING↗

Wavenumber-frequency Spectra of Pressure Fluctuations Measured via Fast Response Pressure Sensitive Paint

The recent advancement in fast-response Pressure-Sensitive Paint (PSP) allows time-resolved measurements of unsteady pressure fluctuations from a dense grid of spatial points on a wind tunnel model. This capability allows for direct calculations of the wavenumber-frequency (k-ω) spectrum of pressure fluctuations. Such data, useful for the vibro-acoustics analysis of aerospace vehicles, are difficult to obtain otherwise. For the present work, time histories of pressure fluctuations on a flat plate subjected to vortex shedding from a rectangular bluff-body were measured using PSP. The light intensity levels in the photographic images were then converted to instantaneous pressure histories by applying calibration constants, which were calculated from a few dynamic pressure sensors placed at selective points on the plate. Fourier transform of the time-histories from a large number of spatial points provided k-ω spectra for pressure fluctuations. The data provides first glimpse into the possibility of creating detailed forcing functions for vibro-acoustics analysis of aerospace vehicles, albeit for a limited frequency range.

Pressure Sensitive Paint↗

Silk I and Silk II studied by fast scanning calorimetry

Using fast scanning calorimetry (FSC), we investigated the glass transition and crystal melting of samples of B. mori silk fibroin containing Silk I and/or Silk II crystals. Due to the very short residence times at high temperatures during such measurements, thermal decomposition of silk protein can be significantly suppressed. FSC was performed at 2000 K/s using the Mettler Flash DSC1 on fibroin films with masses around 130–270 ng. Films were prepared with different crystalline fractions (ranging from 0.26 to 0.50) and with different crystal structures (Silk I, Silk II, or mixed) by varying the processing conditions. These included water annealing at different temperatures, exposure to 50% MeOH in water, or autoclaving. The resulting crystal structure was examined using wide angle X-ray scattering. Degree of crystallinity was evaluated from Fourier transform infrared (FTIR) spectroscopy and from analysis of the heat capacity increment at the glass transition temperature. Silk fibroin films prepared by water annealing at 25 °C were the least crystalline and had Silk I structure. FTIR and FSC studies showed that films prepared by autoclaving or 50% MeOH exposure were the most crystalline and had Silk II structure. Intermediate crystalline fraction and mixed Silk I/Silk II structures were found in films prepared by water annealing at 37 °C. FSC results indicate that Silk II crystals exhibit endotherms of narrower width and have higher mean melting temperature Tm(II) = 351 ± 2.6 °C, compared to Silk I crystals which melt at Tm(I) = 292 ± 3.8 °C. Films containing mixed Silk I/Silk II structure showed two clearly separated endothermic peaks. Evidence suggests that the two types of crystals melt separately and do not thermally interconvert on the extremely short time scale (0.065 s between onset and end of melting) of the FSC experiment.

59 BASIC BIOLOGICAL SCIENCES↗

Optical and structural investigation of GSO gels made via sol gel method

Silica and doped silica materials that are produced by a solution gelation (sol gel) process create versatile materials that have a large range of applications. Coatings, thin films and fibers, nanomaterials, energy conservation materials and optical materials can be synthesized with this technique. Specifically, silica gels have many advantages for optical materials. The gels are transparent and possess a high homogeneity and density. In addition, silica materials can be doped with different compounds to enhance scintillating properties. Gadolinium Oxyorthosilicate (GSO) is a promising candidate as a host for rare earth ions for scintillating applications because of its high stability, density and fast decay time. When a sol gel is dried conventionally, it often shrinks or cracks, forming a xerogel. This work will first focus on forming a transparent GSO host xerogel with sol gel chemistry. Once a transparent GSO xerogel is formulated and characterized, Ce 3+ will be doped into the GSO network. Non-radiative energy transfer from the Gd matrix ions to the Ce 3+ ions occurs because the GSO crystals activated are close in energy to the Ce 3+ f → d transition. GSO: Ce 3+ crystals are currently produced by growing single crystals via Bridgeman and Czochralski methods, which are expensive. Optical ceramics offers a cheap alternative method for making scintillating materials. Structural and thermal characterization of the xerogel will be investigated using X-ray diffraction (XRD), Fourier-transformed infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The materials’ optical properties will be examined by UV-Vis absorption spectroscopy. XRD will be utilized to determine the crystal structure. This will tell determine if the gel is amorphous or crystalline. FTIR was be used to identify functional groups in the gel. DSC and TGA will be used to thermally characterize the gel’s crystallization temperature.

36 MATERIALS SCIENCE↗

Application of Novel Adsorbent Prepared by Mucor hiemalis Biomass Impregnated with Calcium Alginate for Removal of Sr{sup 2+} from Aqueous Solutions

In this research, a novel biosorbent was prepared by Mucor hiemalis biomass combined with calcium alginate (Mucor hiemalis/Alg-Ca). The dead biomass was entrapped into alginate gel by curing method in the presence of Ca{sup 2+} ions. The synthesized biosorbent characterized by XRD, EDAX, BET, FTIR, and SEM techniques was used for removal of Sr{sup 2+} from aquatic streams under various experimental conditions and the optimized adsorption capacity of 140 mg g{sup −1} was obtained. The selectivity of the adsorbent towards Sr{sup 2+} studied in the presence of Na{sup +}, Cs{sup +}, Ca{sup 2+} and Mg{sup 2+} was reasonably high. The adsorption process was kinetically fast and the equilibrium was established within 60 min, and followed the pseudo-second order kinetics model. The equilibrium data was well described by Langmuir isotherm model. The thermodynamics parameters (∆G°, ∆H° and ∆S°) of the process were determined. Positive ∆H° and negative ∆G° were indicative of the endothermic and spontaneous nature of the adsorption process. Graphical Abstract: .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Progress in ITER ECE diagnostic design and integration

The ITER electron cyclotron emission (ECE) diagnostic system has primary roles in providing measurements of the core electron temperature profile and the electron temperature fluctuation associated with the neoclassical tearing modes. The ITER ECE system includes a radial and oblique line-of-sight. Four 43-meter long low-loss transmission lines (TLs) are designed to transmit millimeter wave power in the frequency range of 70–1000 GHz in both X- and O-mode polarization from the port plug to the ECE instrumentation room in the diagnostic building. The measurement instrumentation includes two Fourier transform spectrometer (FTS) systems and two radiometer systems. The Indian Domestic Agency (IN-DA) and United States Domestic Agency share the responsibility. The IN-DA scope excluding instrumentation and control has passed its preliminary design review and is progressing towards the final design review (FDR). In parallel, the diagnostic integration in different areas is ongoing. Furthermore, several captive components for the TLs have passed FDR and will be manufactured for installation in the tokamak building soon. A peer review meeting has been held on the prototype hot calibration source, and its integration and new thermal analysis in the diagnostic shield module are continuing. A prototype TL is being tested. A prototype polarizing Martin-Puplett type FTS, operating in the frequency range 70–1000 GHz, features an in-vacuo fast scanning mechanism and a cryo-cooled dual-channel THz detector system. Its performance has been assessed in detail against ITER requirements.

47 OTHER INSTRUMENTATION↗