Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inlets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Bleed-boundary conditions for numerically simulated mixed-compression supersonic inlet flow

A numerical study was performed to investigate boundary conditions for bleed openings that are needed in the numerical simulation of critical flow through turbojet inlets with bleed. Nine different boundary conditions (BCs) were devised and examined. Of the BCs examined, three were able to stabilize the terminal shock near the inlet's throat. This numerical study was based on the ensemble-averaged, unsteady, three-dimensional, compressible Navier-Stokes equations closed by the Baldwin-Lomax algebraic turbulence model. Solutions to the Navier-Stokes equations were obtained by using a hybrid implicit-explicit method (Beam and Warming/MacCormack). The multiblock grid system used in the solution procedure was generated by solving a set of elliptic partial differential equations. Solutions obtained were compared with available experimental data.

Chyu, W. J.↗

Full Navier-Stokes calculations on the installed F/A-18 inlet at a high angle of attack

Major objectives of the NASA High-Alpha Technology Program are the accurate prediction of the internal (inlet) aerodynamics of an aircraft operating at attitudes of up to 60 deg pitch and 10 deg yaw and the calibration of CFD codes for predicting the internal performance of inlets. Numerical results are presented for the three cases of a full-scale model, a 20-percent scale model at design mass flow, and a scale model at reduced mass flow; attention is given to the effects of Reynolds number. All three cases are at 30 deg angle of attack and zero deg yaw. The results thus obtained are helpful to experimentalists in determining some of their instrumentation requirements.

Bruns, James E.↗

Acoustic mode measurements in the inlet of a model turbofan using a continuously rotating rake: Data collection/analysis techniques

The rotating microphone measurement technique and data analysis procedures are documented which are used to determine circumferential and radial acoustic mode content in the inlet of the Advanced Ducted Propeller (ADP) model. Circumferential acoustic mode levels were measured at a series of radial locations using the Doppler frequency shift produced by a rotating inlet microphone probe. Radial mode content was then computed using a least squares curve fit with the measured radial distribution for each circumferential mode. The rotating microphone technique is superior to fixed-probe techniques because it results in minimal interference with the acoustic modes generated by rotor-stator interaction. This effort represents the first experimental implementation of a measuring technique developed by T. G. Sofrin. Testing was performed in the NASA Lewis Low Speed Anechoic Wind Tunnel at a simulated takeoff condition of Mach 0.2. The design is included of the data analysis software and the performance of the rotating rake apparatus. The effect of experiment errors is also discussed.

Hall, David G.↗

Acoustic Mode Measurements in the Inlet of a Model Turbofan Using a Continuously Rotating Rake

Comprehensive measurements of the spinning acoustic mode structure in the inlet of the Advanced Ducted Propeller (ADP) have been completed. These measurements were taken using a unique and previously untried method which was first proposed by T.G. Sofrin. A continuously rotating microphone system was employed. The ADP model was designed and built by Pratt & Whitney and tested in the NASA Lewis 9- by 15-foot Anechoic Wind Tunnel. Three inlet configurations were tested with cut-on and cutoff stator vane sets. The cutoff stator was designed to suppress all modes at the blade passing frequency. Rotating rake measurements indicate that several extraneous circumferential modes were active. The mode orders suggest that their source was an interaction between the rotor and small interruptions in the casing tip treatment. The cut-on stator produced the expected circumferential modes plus higher levels of the unexpected modes seen with the cutoff stator.

Heidelberg, Laurence J.↗

Acoustic mode measurements in the inlet of a model turbofan using a continuously rotating rake - Data collection/analysis techniques

The rotating microphone measurement technique and data analysis procedures are documented which are used to determine circumferential and radial acoustic mode content in the inlet of the Advanced Ducted Propeller (ADP) model. Circumferential acoustic mode levels were measured at a series of radial locations using the Doppler frequency shift produced by a rotating inlet microphone probe. Radial mode content was then computed using a least squares curve fit with the measured radial distribution for each circumferential mode. The rotating microphone technique is superior to fixed-probe techniques because it results in minimal interference with the acoustic modes generated by rotor-stator interaction. This effort represents the first experimental implementation of a measuring technique developed by T. G. Sofrin. Testing was performed in the NASA Lewis Low Speed Anechoic Wind Tunnel at a simulated takeoff condition of Mach 0.2. The design is included of the data analysis software and the performance of the rotating rake apparatus. The effect of experiment errors is also discussed.

Hall, David G.↗

Acoustic mode measurements in the inlet of a model turbofan using a continuously rotating rake

Comprehensive measurements of the spinning acoustic mode structure in the inlet of the Advanced Ducted Propeller (ADP) have been completed. These measurements were taken using a unique and previously untried method which was first proposed by T.G. Sofrin. A continuously rotating microphone system was employed. The ADP model was designed and built by Pratt & Whitney and tested in the NASA Lewis 9- by 15-foot Anechoic Wind Tunnel. Three inlet configurations were tested with cut-on and cutoff stator vane sets. The cutoff stator was designed to suppress all modes at the blade passing frequency. Rotating rake measurements indicate that several extraneous circumferential modes were active. The mode orders suggest that their source was an interaction between the rotor and small interruptions in the casing tip treatment. The cut-on stator produced the expected circumferential modes plus higher levels of the unexpected modes seen with the cutoff stator.

Heidelberg, Laurence J.↗

An experimental parametric study of geometric, Reynolds number, and ratio of specific heats effects in three-dimensional sidewall compression scramjet inlets at Mach 6

The effects of the decrease in the ratio of specific heats have been investigated in generic 3D sidewall compression scramjet inlets with leading-edge sweep angles of 30 and 70 degrees. The effects of a decrease in ratio of specific heats were seen by comparing data from two facilities in two test gases: in the Langley Mach 6 CF4 Tunnel in tetrafluoromethane and in the Langley 15-Inch Mach 6 Air Tunnel in perfect gas air. In addition to the simulated real gas effects, the parametric effects of cowl position, contraction ratio, leading-edge sweep, and Reynolds number were investigated in the 15-Inch Mach 6 Air Tunnel. The models were instrumented with a total of 45 static pressure orifices distributed on the sidewalls and baseplate. Surface streamline patterns were examined via oil flow, and schlieren videos were made of the external flow field. The results of these tests have significant implications to ground based testing of inlets in facilities which do not operate at flight enthalpies.

Holland, Scott D.↗

A comparative study of Full Navier-Stokes and Reduced Navier-Stokes analyses for separating flows within a diffusing inlet S-duct

A three-dimensional implicit Full Navier-Stokes (FNS) analysis and a 3D Reduced Navier Stokes (RNS) initial value space marching solution technique has been applied to a class of separated flow problems within a diffusing S-duct configuration characterized by vortex-liftoff. Both the FNS and the RNS solution technique were able to capture the overall flow physics of vortex lift-off, and gave remarkably similar results which agreed reasonably well with the experimental measured averaged performance parameters of engine face total pressure recovery and distortion. However, the Full Navier-Stokes and Reduced Navier-Stokes also consistently predicted separation further downstream in the M2129 inlet S-duct than was indicated by experimental data, thus compensating errors were present in the two Navier-Stokes analyses. The difficulties encountered in the Navier-Stokes separations analyses of the M2129 inlet S-duct center primarily on turbulence model issues, and these focused on two distinct but different phenomena, namely, (1) characterization of low skin friction adverse pressure gradient flows, and (2) description of the near wall behavior of flows characterized by vortex lift-off.

Anderson, B. H.↗

Preliminary Investigation of Effect on Performance of Dividing Conical-spike Nose Inlets into Halves at Mach Numbers 1.5 to 2.0

Inserting a splitter plate in the subsonic diffuser caused a pressure-recovery loss of about 1 percent for an inlet with a long nearly constant-area throat section. The loss was due to the increased surface area. Another inlet, which had a comparatively rapid area increase immediately after the throat, experienced pressure-recovery losses of 5 and 6 percent at Mach numbers of 1.8 and 2.0, respectively, and about 1 percent at Mach 1.5.

Allen, John L↗

A variable-geometry annular cascade-type inlet at Mach numbers of 1.9 and 3.05

A variable-geometry annular cascade-type inlet is proposed and demonstrated. Such an inlet yielded total-pressure recoveries of 0.84 and 0.53 at Mach numbers of 1.9 and 3.05., respectively. Unity mass-flow ratios were obtained at each Mach number with only marginal subcritical stability ranges of mass-flow ratio (?0.03). Angles of attack up to 6 percent produced only moderate decreases in performance.

Connors, James F↗

Performance of a Supersonic Ramp-type Side Inlet with Ram-scoop Throat Bleed and Varying Fuselage Boundary-layer Removal : Mach Number Range 1.5 to 2.0 / Glenn A. Mitchell and Robert C. Campbell

Provided sufficient throat bleed was employed, maximum pressure recoveries of 0.87 to 0.88 at Mach number 2.0 were obtained for a fuselage-mounted 14 degrees ramp inlet regardless of the amount of fuselage boundary layer ingested. The addition of inlet side fairings yielded further increases in pressure recovery to 0.90 to 0.91, decreased critical drag coefficients, and increased critical mass-flow ratios. With throat bleed, peak pressure recoveries and calculated thrust-minus-drag values were comparable at two axial positions of the scoop and were highest with the greatest amount of fuselage boundary layer ingested.

Mitchell, Glenn A↗

Experimental investigation of water injection in subsonic diffuser of a conical inlet operation at free-stream Mach number of 2.5

A spike-type nose inlet with sharp-lip cowl was investigated at a free-stream Mach number of 2.5 with water injection in its 16-inch diameter, 11-foot-long subsonic diffuser section. Inlet total temperature of exit with liquid-air ratios of about 0.04 with no apparent change in the critical pressure recovery. The observed temperature drops were less than the theoretically predicted values, and the amount of water evaporated was 35 to 50 percent less than that theoretically possible.

Beke, Andrew↗

Preliminary Investigation of a New Type of Supersonic Inlet

A supersonic inlet with supersonic deceleration of the flow entirely outside of the inlet is considered a particular arrangement with fixed geometry having a central body with a circular annular intake is analyzed, and it is shown theoretically that this arrangement gives high pressure recovery for a large range of Mach number and mass flow and, therefore, is practical for use on supersonic airplanes and missiles. Experimental results confirming the theoretical analysis give pressure recoveries which vary from 95 percent for Mach number 1.33 to 86 percent for number 2.00. These results were originally presented in a classified document of the NACA in 1946.

Ferri, Antonio↗

Several examples where turbulence models fail in inlet flow field analysis

Computational uncertainties in turbulence modeling for three dimensional inlet flow fields include flows approaching separation, strength of secondary flow field, three dimensional flow predictions of vortex liftoff, and influence of vortex-boundary layer interactions; computational uncertainties in vortex generator modeling include representation of generator vorticity field and the relationship between generator and vorticity field. The objectives of the inlet flow field studies presented in this document are to advance the understanding, prediction, and control of intake distortion and to study the basic interactions that influence this design problem.

Anderson, Bernhard H.↗

Computational Methods for HSCT-Inlet Controls/CFD Interdisciplinary Research

A program aimed at facilitating the use of computational fluid dynamics (CFD) simulations by the controls discipline is presented. The objective is to reduce the development time and cost for propulsion system controls by using CFD simulations to obtain high-fidelity system models for control design and as numerical test beds for control system testing and validation. An interdisciplinary team has been formed to develop analytical and computational tools in three discipline areas: controls, CFD, and computational technology. The controls effort has focused on specifying requirements for an interface between the controls specialist and CFD simulations and a new method for extracting linear, reduced-order control models from CFD simulations. Existing CFD codes are being modified to permit time accurate execution and provide realistic boundary conditions for controls studies. Parallel processing and distributed computing techniques, along with existing system integration software, are being used to reduce CFD execution times and to support the development of an integrated analysis/design system. This paper describes: the initial application for the technology being developed, the high speed civil transport (HSCT) inlet control problem; activities being pursued in each discipline area; and a prototype analysis/design system in place for interactive operation and visualization of a time-accurate HSCT-inlet simulation.

Cole, Gary L.↗

Design and development of an F/A-18 inlet distortion rake: A cost and time saving solution

An innovative inlet total-pressure distortion measurement rake has been designed and developed for the F/A-18 A/B/C/D aircraft inlet. The design was conceived by NASA and General Electric Aircraft Engines (Evendale, Ohio). This rake has been flight qualified and flown in the F-18 High Alpha Research Vehicle (HARV) at NASA Dryden Flight Research Center. The rake's eight-legged, one-piece wagon wheel design was developed at a reduced cost and offers reduced installation time compared with traditional designs. The rake features 40 dual measurement ports for both low- and high-frequency pressure measurements with the high-frequency transducer mounted at the port. The high-frequency transducer offers direct absolute pressure measurements from low frequency to the highest frequency of interest, thereby allowing the rake to be used during highly dynamic aircraft maneuvers. Outstanding structural characteristics are inherent to the design through its construction and use of lightweight materials.

Yuhas, Andrew J.↗

Numerical Simulation of Supersonic Compression Corners and Hypersonic Inlet Flows Using the RPLUS2D Code

A two-dimensional computational code, PRLUS2D, which was developed for the reactive propulsive flows of ramjets and scramjets, was validated for two-dimensional shock-wave/turbulent-boundary-layer interactions. The problem of compression corners at supersonic speeds was solved using the RPLUS2D code. To validate the RPLUS2D code for hypersonic speeds, it was applied to a realistic hypersonic inlet geometry. Both the Baldwin-Lomax and the Chien two-equation turbulence models were used. Computational results showed that the RPLUS2D code compared very well with experimentally obtained data for supersonic compression corner flows, except in the case of large separated flows resulting from the interactions between the shock wave and turbulent boundary layer. The computational results compared well with the experiment results in a hypersonic NASA P8 inlet case, with the Chien two-equation turbulence model performing better than the Baldwin-Lomax model.

Kapoor, Kamlesh↗