Results for “Optimized Configurations” — Page 56

NASA NTRS1972

Optimal lifting ascent trajectories for the space shuttle

The performance gains which are possible through the use of optimal trajectories for a particular space shuttle configuration are discussed. The spacecraft configurations and aerodynamic characteristics are described. Shuttle mission payload capability is examined with respect to the optimal orbit inclination for unconstrained, constrained, and nonlifting conditions. The effects of velocity loss and heating rate on the optimal ascent trajectory are investigated.

Rau, T. R.↗

DOE OSTI2023

Optimization-Based Azeotropic Distillation System Synthesis Using Geometric Insights

The synthesis of azeotropic distillation systems is challenging due to the existence of compartments in the residue curve map coupled with the combinatorial aspects from numerous possible system configurations. In this work, an optimization-based approach is introduced to synthesize homogeneous azeotropic distillation systems. The approach employs a network-based representation generated via a matrix method. To design the distillation columns, the modified Underwood equations are adopted, in which pseudocomponent-based compositions are used. For cases where separatrices are significantly curved, corrections via piece-wise linear functions and collinearity properties are implemented. Two examples are presented to illustrate the proposed approach.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2018

Design and simulation of the snowflake divertor control for NSTX-U

This study presents the development of a physics-based multiple-input-multiple-output algorithm for real-time feedback control of snowflake divertor (SFD) configurations on the National Spherical Torus eXperiment Upgrade (NSTX-U). A model of the SFD configuration response to applied voltages on the divertor control coils is first derived and then used, in conjunction with multivariable control synthesis techniques, to design an optimal state feedback controller for the configuration. To demonstrate the capabilities of the controller, a nonlinear simulator for axisymmetric shape control was developed for NSTX-U which simultaneously evolves the currents in poloidal field coils based upon a set of feedback-computed voltage commands, calculates the induced currents in passive conducting structures, and updates the plasma equilibrium by solving the free-boundary Grad-Shafranov problem. Closed-loop simulations demonstrate that the algorithm enables controlled operations in a variety of SFD configurations and provides capabilities for accurate tracking of time-dependent target trajectories for the divertor geometry. In particular, simulation results suggest that a time-varying controller which can properly account for the evolving SFD dynamical response is not only desirable but necessary for achieving acceptable control performance. The algorithm presented in this paper has been implemented in the NSTX-U Plasma Control System in preparation for future control and divertor physics experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2019

Design and simulation of the snowflake divertor control for NSTX-U

This paper presents the development of a physics-based multiple-input-multiple-output algorithm for real-time feedback control of snowflake divertor (SFD) configurations on the National Spherical Torus eXperiment Upgrade (NSTX-U). A model of the SFD configuration response to applied voltages on the divertor control coils is first derived and then used, in conjunction with multivariable control synthesis techniques, to design an optimal state feedback controller for the configuration. To demonstrate the capabilities of the controller, a nonlinear simulator for axisymmetric shape control was developed for NSTX-U which simultaneously evolves the currents in poloidal field coils based upon a set of feedback-computed voltage commands, calculates the induced currents in passive conducting structures, and updates the plasma equilibrium by solving the free-boundary Grad-Shafranov problem. Closed-loop simulations demonstrate that the algorithm enables controlled operations in a variety of SFD configurations and provides capabilities for accurate tracking of time-dependent target trajectories for the divertor geometry. In particular, simulation results suggest that a time-varying controller which can properly account for the evolving SFD dynamical response is not only desirable but necessary for achieving acceptable control performance. The algorithm presented in this paper has been implemented in the NSTX-U Plasma Control System in preparation for future control and divertor physics experiments.

snowflake divertor, MIMO feedback control, nonline↗

NASA NTRS1973

Warm gas TVC design study

A warm gas thrust vector control system was studied to optimize the injection geometry for a specific engine configuration, and an injection valve was designed capable of meeting the base line requirements. To optimize injection geometry, studies were made to determine the performance effects of varying injection location, angle, port size, and port configuration. Having minimized the injection flow rate required, a warm gas valve was designed to handle the required flow. A direct drive hydraulic servovalve capable of operating with highly contaminated hydraulic fluid was designed. The valve is sized to flow 15 gpm at 3000 psia and the direct drive feature is capable of applying a spool force of 200 pounds. The baseline requirements are the development of 6 deg of thrust vector control utilizing 2000 F (total temperature) gas for 180 seconds on a 1.37 million pound thrust engine burning LOX and RP-1 at a chamber pressure of 250 psia with a 155 inch long conical nozzle having a 68 inch diameter throat and a 153 inch diameter exit.

Moorhead, S. B., Jr.↗

NASA NTRS1980

Development of a vortex-lift-design method and application to a slender maneuver-wing configuration

A method has been developed to optimize the mean camber surface of a cranked slender wing having leading-edge vortex flow at transonic-maneuver conditions using the suction analogy. This type of flow was assumed because it was anticipated that the slenderness of the wing would preclude attached flow at the required lift coefficient. A constraint was imposed in that the camber deflections were to be restricted by a realistic structural-box requirement. The resulting application yielded mean-camber shapes which produced effective suction levels equivalent to 77 percent of the full-planar leading-edge value at the design lift coefficient.

Lamar, J. E.↗

NASA NTRSDate not supplied

Integration of Low-Fidelity MDO and CFD-Based Redesign of Low-Boom Supersonic Transports

A mixed-fidelity low-boom multidisciplinary optimization (MDO) problem is formulated for integration of low-fidelity MDO and computational fluid dynamics (CFD) based low-boom inverse design optimization. The mixed-fidelity low-boom MDO problem aims to enforce the weight consistency for CFD-based low-boom inverse design optimization: the optimum low-boom configuration is designed for the weight at the start of cruise of the same configuration for the low-boom overland mission. Moreover, it also seeks the optimum trades among the maximum takeoff gross weight (MTOGW), cruise Mach, and range for the low-boom overland mission while meeting the requirement of flying a transatlantic overwater mission. A block coordinate optimization (BCO) method is developed to find an approximate solution of the mixed-fidelity low-boom MDO problem. The BCO method is successfully applied to generate two CFD-based low-boom configurations that closely match two reversed equivalent area targets with ground noise levels below 70 PLdB, respectively. Moreover, these CFD-based low-boom configurations can be obtained with minor wing modifications from the solutions of the low-fidelity MDO problem. The low-fidelity MDO solutions are Pareto points for constrained multiobjective optimization of MTOGW, low-boom cruise Mach, and low-boom range. The best low-boom concept has a predetermined fuselage shape tailored for passengers and main gear storage, carries 40 passengers at seat pitch of 48 in, flies a low-boom overland mission with cruise Mach of 1.8 and range of 2,950 nm, cruises overwater at Mach 1.8 with range of 3,600 nm, satisfies the specified constraints for landing/cruise/takeoff, has MTOGW of 145,164 lb, trims the low-boom cruise flight with fuel redistributions instead of control surface deflections, and has a reversed equivalent area distribution closely matching a target with ground noise level below 70 PLdB.

multidisciplinary optimization↗

NASA NTRSDate not supplied

Integration of Low-Fidelity MDO and CFD-Based Redesign of Low-Boom Supersonic Transports

A mixed-fidelity low-boom multidisciplinary optimization (MDO) problem is formulated for integration of low-fidelity MDO and computational fluid dynamics (CFD) based low-boom inverse design optimization. The mixed-fidelity low-boom MDO problem aims to enforce the weight consistency for CFD-based low-boom inverse design optimization: the optimum low-boom configuration is designed for the weight at the start of cruise of the same configuration for the low-boom overland mission. Moreover, it also seeks the optimum trades among the maximum takeoff gross weight (MTOGW), cruise Mach, and range for the low-boom overland mission while meeting the requirement of flying a transatlantic overwater mission. A block coordinate optimization (BCO) method is developed to find an approximate solution of the mixed-fidelity low-boom MDO problem. The BCO method is successfully applied to generate two CFD-based low-boom configurations that closely match two reversed equivalent area targets with ground noise levels below 70 PLdB, respectively. Moreover, these CFD-based low-boom configurations can be obtained with minor wing modifications from the solutions of the low-fidelity MDO problem. The low-fidelity MDO solutions are Pareto points for constrained multiobjective optimization of MTOGW, low-boom cruise Mach, and low-boom range. The best low-boom concept has a predetermined fuselage shape tailored for passengers and main gear storage, carries 40 passengers at seat pitch of 48 in, flies a low-boom overland mission with cruise Mach of 1.8 and range of 2,950 nm, cruises overwater at Mach 1.8 with range of 3,600 nm, satisfies the specified constraints for landing/cruise/takeoff, has MTOGW of 145,164 lb, trims the low-boom cruise flight with fuel redistributions instead of control surface deflections, and has a reversed equivalent area distribution closely matching a target with ground noise level below 70 PLdB.

low-boom supersonic transports↗

NASA NTRS2021

Integration of Low-Fidelity MDO and CFD-Based Redesign of Low-Boom Supersonic Transports

A mixed-fidelity low-boom multidisciplinary optimization (MDO) problem is formulated for integration of low-fidelity MDO and computational fluid dynamics (CFD) based low-boom inverse design optimization. The mixed-fidelity low-boom MDO problem aims to enforce the weight consistency for CFD-based low-boom inverse design optimization: the optimum low-boom configuration is designed for the weight at the start of cruise of the same configuration for the low-boom overland mission. Moreover, it also seeks the optimum trades among the maximum takeoff gross weight (MTOGW), cruise Mach, and range for the low-boom overland mission while meeting the requirement of flying a transatlantic overwater mission. A block coordinate optimization (BCO) method is developed to find an approximate solution of the mixed-fidelity low-boom MDO problem. The BCO method is successfully applied to generate two CFD-based low-boom configurations that closely match two reversed equivalent area targets with ground noise levels below 70 PLdB, respectively. Moreover, these CFD-based low-boom configurations can be obtained with minor wing modifications from the solutions of the low-fidelity MDO problem. The low-fidelity MDO solutions are Pareto points for constrained multiobjective optimization of MTOGW, low-boom cruise Mach, and low-boom range. The best low-boom concept has a predetermined fuselage shape tailored for passengers and main gear storage, carries 40 passengers at seat pitch of 48 in, flies a low-boom overland mission with cruise Mach of 1.8 and range of 2,950 nm, cruises overwater at Mach 1.8 with range of 3,600 nm, satisfies the specified constraints for landing/cruise/takeoff, has MTOGW of 145,164 lb, trims the low-boom cruise flight with fuel redistributions instead of control surface deflections, and has a reversed equivalent area distribution closely matching a target with ground noise level below 70 PLdB.

low-boom supersonic transports↗

NASA NTRS1967

Discharge Chamber Optimization of the SERT II Thrustor

Optimum discharge chamber configuration of permanent magnet mercury-bombardment thrustor for SERT II mission

OPTIMIZATION↗

NASA NTRSDate not supplied

Autonomous Constrained Control for Arbitrary Thruster Configurations of Gimbaling Thrusters in SE(3)

In order to develop robust autonomy in spacecraft, it is desirable to develop methods for guiding and controlling arbitrarily-configured spacecraft with any combination of thrusters of various types, i.e. either static reaction control system thrusters and gimbaling thrusters. Scenarios in which autonomous selection of thrusters may be needed include the case of a stuck or inhibited thruster that restricts the motion of the vehicle, vehicles with changing mass properties such as logistics modules or tugs, or vehicles that have imposed constraints on thrusters during docking in order to avoid plume impingement on a space station or adjacent spacecraft. To that end, a spacecraft must be able to rapidly and autonomously reconfigure thruster firing histories and update guidance protocols in accordance with newly imposed constraints. In this paper, a methodology is presented that enables a spacecraft to autonomously select thrusters of any configuration and type in order to optimally match a desired 6-degree-of-freedom navigation and control within the special Euclidean SE(3) framework. The residual motion imposed by off-nominal thruster configurations or thrusters that are not fully controllable is identified by the spacecraft and solved for over time, both for static reaction control systems and for the case of gimbaling thrusters.

GN&C↗

DOE OSTI2025

Plant Reload Optimization (prlo)

The PRLO framework is built on a modular and extensible architecture that tightly couples advanced evolutionary optimization algorithms with nuclear fuel depletion solvers (i.e., nuclear physics neutronics code). It supports exploring complex, high-dimensional design spaces constrained by user-specified operational, safety, and economic constraints. Objectives such as minimizing fresh fuel enrichment, flattening radial and axial power distributions, and maximizing discharge burnup are evaluated. PRLO’s equilibrium cycle optimization capability enables the identification of core configurations that maintain fuel cycle sustainability over extended planning horizons. Its integration with the RAVEN platform facilitates optimization of loading patterns or fuel shuffling schemes across multiple cycles. The interface with SIMULATE, a licensed industry-standard nodal code developed by Studsvik, ensures accurate neutronic and thermal-hydraulic feedback for reactor core design. PRLO’s automated workflow engine supports iterative design refinement, enabling utilities to streamline core design processes and meet evolving performance and regulatory targets.

Kim, Junyung [Idaho National Laboratory] (00090005↗

NASA NTRS1983

Design considerations for FET-gated power transistors

An FET-bipolar combinational power transistor configuration (tested up to 300 V, 20 A at 100 kHz) is described. The critical parameters for integrating the chips in hybrid form are examined, and an effort to optimize the overall characteristics of the configuration is discussed. Chip considerations are examined with respect to the voltage and current rating of individual chips, the FET surge capability, the choice of triple diffused transistor or epitaxial transistor for the bipolar element, the current tailing effect, and the implementation of the bipolar transistor and an FET as single chip or separate chips. Package considerations are discussed with respect to package material and geometry, surge current capability of bipolar base terminal bonding, and power losses distribution.

Chen, D. Y.↗

DOE OSTI2020

Moving from residual lignocellulosic biomass into high–value products: Outcomes from a long–term international cooperation

Major progress in the bioprocessing of lignocellulose to fuels and value-added chemicals has created the possibility of a low carbon-footprint economy. However, the current complexity and associated costs of lignocellulose conversion result in a higher price for ethanol than for fossil fuels. The cost of cellulosic ethanol production will be lowered by further progress in development of biorefinery technology that produces both ethanol and high-value chemicals with bio-based products that are beginning to penetrate consumer markets in the USA, Brazil, and worldwide. The cost-effectiveness of low carbon-footprint bioproducts will benefit from advances in supplying large amounts of biomass solids to the biorefinery. We describe here outcomes from a successful long-term international cooperation between the Laboratory of Renewable Resources Engineering (LORRE) at Purdue University in the United States and Brazil's Agricultural Research Corporation (EMBRAPA) and Federal University of Sâo Carlos (UFSCar), which has contributed practical pathways to enhance the biorefinery concept. Furthermore, this paper gives an overview of developments that address fundamental knowledge of lignocellulosic biomass pretreatment hydrolysis under optimized operational conditions and bioreactor configurations, and the science and engineering that contributes to the effective production of fuel and ethanol and value-added products from biomass.

09 BIOMASS FUELS↗

DOE OSTI2024

A high-volume resonator for L-band DNP-NMR

DNP-NMR and EPR experiments that operate at or greater than L-band (i.e., ν 0 (e – ) = 1–2 GHz) are typically limited to maximum sample volumes of several hundred µL. These experiments rely on well-known resonator designs for DNP/EPR irradiation such as the loop-gap resonator and Alderman-Grant coil, where their maximum volumes limit further application to imaging experiments and high-throughput screening beyond L-band. Herein, we demonstrate a birdcage (BC) resonator design that can accommodate several mL of sample while operating around 1.5 GHz. The sample volume is maximized by using two identical BC resonators in a stacked configuration. Simulations are used to optimize the BC design and the performance is validated experimentally with liquid-state Overhauser-DNP-NMR experiments. This BC design exploits just the parasitic capacitance of conductive rings and features no fixed tuning capacitors. An enhancement of –77 is achieved on a 10 mM 4-Amino-TEMPO in H 2 O sample for a 5 mL sample volume. Finally, the associated sample heating is minimal due to the low-E-fields generated and the large sample mass with +3.4 K when driving 100 W for several seconds.

47 OTHER INSTRUMENTATION↗

DOE OSTI2022

Understanding the effect of salt concentrations on fast charging performance of Li-ion cells

Here, different lithium salt (lithium bis(fluorosulfonyl) imide (LiFSI)/LiPF 6 9/1 mol ratio) concentrations in carbonate electrolyte were studied on the fast charging performance of LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622)/graphite pouch cells. The cells with electrolyte concentration from 0.75 M to 1.50 M showed similar fast charging capabilities. Further increase of the concentration to 1.75 M and 2.00 M decreased the attainable capacity in fast charging. In the long-term cycling test, the capacity retention after 200 fast charging cycles increased with the increase of salt concentration in electrolyte. Cells with 1.5 M electrolyte showed the best overall performance in fast charging capacity and long-term cycling. Li platings were observed in the cells with 0.75 M, 1.00 M and 1.25 M electrolyte. It was improved with greatly reduced Li plating area in 1.50 M, and no Li plating at all in 1.75 M and 2.00 M electrolyte. Post-mortem analysis such as neutron powder diffraction (NPD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the electrode after cycling. It suggests that electrolyte concentration needs to be optimized for a given cell configuration with specific electrode and loading.

25 ENERGY STORAGE↗

DOE OSTI2019

Large area planar photocathode for MCP-based photodetectors

We report on the principle, design, fabrication, and characterization of a large-area planar bialkali photocathode. Herein, sequential photocathode growth process was investigated, and the growth parameters, especially the initial antimony layer thickness, were optimized. The source arrangement and configuration were also simulated and the preferred configuration was chosen for numerical and experimental studies. Photocathode with average QE of 18% and activation area of similar to 40 square inches was experimentally demonstrated, making it a candidate for MCP-based photodetector applications. Further improvements were also discussed to enhance the uniformity and QE value of the photocathodes.

47 OTHER INSTRUMENTATION↗

DOE OSTI2024

Hydrogen production in microbial electrolysis cells with biocathodes

Electroautotrophic microbes at biocathodes in microbial electrolysis cells (MECs) can catalyze the hydrogen evolution reaction with low energy demand, facilitating long-term stable performance through specific and renewable biocatalysts. However, MECs have not yet reached commercialization due to a lack of understanding of the optimal microbial strains and reactor configurations for achieving high performance. Here, we critically analyze the criteria for the inocula selection, with a focus on the effect of hydrogenase activity and microbe–electrode interactions. We also evaluate the impact of the reactor design and key parameters, such as membrane type, composition, and electrode surface area on internal resistance, mass transport, and pH imbalances within MECs. Furthermore, this analysis paves the way for advancements that could propel biocathode-assisted MECs toward scalable hydrogen gas production.

Biotechnology & Applied Microbiology↗