Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Analyses of Fatigue Crack Growth and Closure Near Threshold Conditions for Large-Crack Behavior

A plasticity-induced crack-closure model was used to study fatigue crack growth and closure in thin 2024-T3 aluminum alloy under constant-R and constant-K(sub max) threshold testing procedures. Two methods of calculating crack-opening stresses were compared. One method was based on a contact-K analyses and the other on crack-opening-displacement (COD) analyses. These methods gave nearly identical results under constant-amplitude loading, but under threshold simulations the contact-K analyses gave lower opening stresses than the contact COD method. Crack-growth predictions tend to support the use of contact-K analyses. Crack-growth simulations showed that remote closure can cause a rapid rise in opening stresses in the near threshold regime for low-constraint and high applied stress levels. Under low applied stress levels and high constraint, a rise in opening stresses was not observed near threshold conditions. But crack-tip-opening displacement (CTOD) were of the order of measured oxide thicknesses in the 2024 alloy under constant-R simulations. In contrast, under constant-K(sub max) testing the CTOD near threshold conditions were an order-of-magnitude larger than measured oxide thicknesses. Residual-plastic deformations under both constant-R and constant-K(sub max) threshold simulations were several times larger than the expected oxide thicknesses. Thus, residual-plastic deformations, in addition to oxide and roughness, play an integral part in threshold development.

Newman, J. C., Jr.↗

Evolution of the Shape of Detached GeSi Crystals in Microgravity

A series of GeSi crystal growth experiments are planned to be conducted in the Low Gradient Furnace (LGF) onboard the International Space Station. An objective of these experiments is to understand the mechanisms of detached Bridgman growth, a process in which a gap exists between the growing semiconductor crystal and the crucible wall. Crystals grown without wall contact have superior quality to otherwise similar crystals grown in direct contact with a container, especially with respect to impurity incorporation, formation of dislocations, and residual stress in crystals. Numerical calculations are used to determine the conditions in which a gap can exist. According to crystal shape stability theory, only some of these gap widths will be dynamically stable. Beginning with a crystal diameter that differs from stable conditions, the transient crystal growth process is analyzed. In microgravity, dynamic stability depends only on capillary effects and is decoupled from heat transfer. Depending on the initial conditions and growth parameters, the crystal shape will evolve towards the crucible wall, towards a stable gap width, or towards the center of the crucible, collapsing the meniscus.

Volz, M. P.↗

Evolution of the Shape of Detached GeSi Crystals in Microgravity

A series of GeSi crystal growth experiments are planned to be conducted in the Low Gradient Furnace (LGF) onboard the International Space Station. An objective of these experiments is to understand the mechanisms of detached Bridgman growth, a process in which a gap exists between the growing semiconductor crystal and the crucible wall. Crystals grown without wall contact have superior quality to otherwise similar crystals grown in direct contact with a container, especially with respect to impurity incorporation, formation of dislocations, and residual stress in crystals. Numerical calculations are used to determine the conditions in which a gap can exist. According to crystal shape stability theory, only some of these gap widths will be dynamically stable. Beginning with a crystal diameter that differs from stable conditions, the transient crystal growth process is analyzed. In microgravity, dynamic stability depends only on capillary effects and is decoupled from heat transfer. Depending on the initial conditions and growth parameters, the crystal shape will evolve towards the crucible wall, towards a stable gap width, or towards the center of the crucible, collapsing the meniscus.

Volz, M. P.↗

Mechanical Design of the HER Synchrotron Light Monitor Primary Mirror

This paper describes the mechanical design of the primary mirror that images the visible portion of the synchrotron radiation (SR) extracted from the High Energy Ring (HER) of the PEP-II B-Factory. During off-axis operation, the water-cooled GlidCop mirror is subjected to a heat flux in excess of 2000 W/cm2. When on-axis imaging occurs, the heat flux due to scattered SR, resistive wall losses and Higher-Order-Mode (HOM) heating is estimated at 1 W/cm2. The imaging surface is plated with Electroless Nickel to improve its optical characteristics. The design requirements for the primary mirror are listed and discussed. Calculated mechanical distortions and stresses experienced by the mirror during on-axis and off-axis operation will be presented.

43 PARTICLE ACCELERATORS↗

Determination of the mechanical properties of blisters by nanoindentation

In light-water reactors, a zirconium oxide layer will be formed at the outer surface of the fuel cladding as a consequence of the chemical reaction which takes place between zirconium and the cooling water. This zirconium oxide layer is a good thermal insulator, but at some point, it may spall-out. As a consequence, a cold spot will be formed at the outer surface of the cladding. In this situation, the hydrogen will quickly migrate to this spot to form a highly-enriched hydride zone, known as blister. In this work, an experimental procedure has been devised to produce blisters with a similar shape to the ones reported in the literature for irradiated cladding with severe hydriding. Nano-indentation tests were performed on blisters prepared in laboratory. A numerical simulation by the finite element method was developed to fit the load versus penetration depth data from the aforementioned nano-indentation tests. By means of an inverse process which combines experimental data and numerical simulations, the constitutive equation of the blister was determined. The process has been used to calculate the plastic stress-strain curve of the blister under study at room temperature. The results show an almost perfect numerical fitting of the experimental data.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Adhesion Capabilities of Permanent Foaming Fixatives

DOE-EM have identified an operational requirement for a fixative that can immobilize and/or encapsulate residual contamination in 3D void volumes (pipes, gloveboxes, waste containers, etc.) during D and D activities. Failure to safely and effectively immobilize residual contamination can: Put workers at risk; Contaminate the public and environment; Drive up costs. Commercial-off-the-shelf (COTS) polyurethane (PU) foams is one possible solution and is currently being investigated by Savannah River National Lab (SRNL). Adhesion testing will dictate how well PU foams will adhere and immobilize residual contamination onto a substrate. Results can provide a performance criteria for Section 5 of ASTM E3191: Standard Specification for Permanent Foaming Fixatives Used to Mitigate Spread of Radioactive Contamination. Initial mechanical testing showed intumescent rigid PU foams were best in class (tensile, compression, TGA/DSC) Application of intumescent rigid PU foam in pipe scenario with 'contamination' showed excellent adhesion capabilities as long as foam had contact with pipe. The foam, however, was not able to penetrate 'contamination' but created pockets where the contamination interacted with the substrate. Pretreatment options of pipe were considered to produce better immobilization capabilities. Pretreatment options included COTS products like baking spray, rubber cement, and soap. Foam was still able to immobilize on a global sense, but not a local sense. Essentially acted as a mechanical plug. A tensile tester (MTS Criterion Series 43) was utilized to evaluate the tensile adhesion strength of 6 COTS PU foams. ASTM D1623: Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics. Procedures: PU foams were cured between two smooth 2'' x 2'' 304 stainless steel coupons with hinges glued on plates for gripping support. Parameters Used: Pull rate of 0.1 in/min. Calculations: Tensile adhesion strength, elongation, and ImageJ analysis of how PU foam is left on substrate. Outcome: The PU foam with the best adhesion capabilities would be downselected for further evaluation to be used as a permanent foaming fixative. The rigid PU foams had the best adhesion capabilities with the R1 foam having a max load of 236 N. One of the I-R2 samples reached almost 450 N and another sample reached 2500 N before slipping. The other intumescent foam, I-F4, had the most coverage on the stainless steel coupon's surface from the ImageJ results (61.43% surface coverage). The intumescent foam, I-R2, will be the foam of choice for future testing due its fire retardant and adhesion capabilities. Future directions: Conduct the following experiment in a pipe scenario with the down-selected PU foam. Procedures: PU foam will be cured between in a 304 stainless steel pipe (ID: 4'', OD: 4.5'', Height: 4''). Parameters Used: Compression testing results will be referenced to determine if foam's adhesion strength would be greater its compression strength as its being compressed. Calculations: Compression strength, shear stress, total time elapsed. Conduct further adhesion testing with the down-selected PU foam (I-R2) to be treated as a permanent foaming fixative (PFF). Determine the minimum contact the PFF should have with the substrate for adequate results. Evaluate if PFF's adhesion capabilities is time dependent (3.1.5 of ASTM E3911). Subject PFF to seismic stressors addressed in Safety Basis of Interim Operation documents (SBIO) to further evaluate adhesion capabilities.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Composite-Plate-Buckling Analysis Program

Composite-Plate-Buckling Analysis Program (COMPPAP) helps engineers determine buckling loads of orthotropic or isotropic irregularly shaped plates without need to perform manual calculations and extensive finite-element mathematical modeling. One-element finite-element program utilizing high-order displacement functions to perform plane-stress analysis of general plate followed by buckling calculation based on stresses found in plane-stress solution. High order of displacement functions enables user to obtain results more accurately. Written in ANSI FORTRAN 77. Two machine versions available: (MSC-22428) for computers of IBM PC 386 and higher series and for compatible computers; and UNIX (MSC-22286).

Smith, James P.↗

Influence of Welding Strength Matching Coefficient and Cold Stretching on Welding Residual Stress in Austenitic Stainless Steel

Austenitic stainless steel is widely used in pressure vessels for the storage and transportation of liquid gases such as liquid nitrogen, liquid oxygen, and liquid hydrogen. Cryogenic pressure vessel manufacturing uses cold stretching technology, which relies heavily on welding joint performance, to construct lightweight and thin-walled vessels. Residual stress from welding is a primary factor in cases of austenitic stainless steel pressure vessel failure. In this paper, on the basis of Visual Environment 10.0 finite element simulation technology, the residual stress resulting from different welding strength matching coefficients (0.8, 1, 1.2, 1.4) for two S30408 plates welded with three-pass butt welds is calculated according to thermal elastoplastic theory. In addition, the stress field was calculated under a loading as high as 410 MPa and after the load was released. Path 1 was set to analyze stress along the welding line, and path 2 was set to analyze stress normal to the welding line. The welding strength matching coefficient strongly affected both the longitudinal residual stress (center of path 1) and the transverse residual stress (both ends of path 1) after the welding was completed. However, the coefficient had little effect on the longitudinal and transverse residual stress of path 2. Under the loading of 410 MPa, the longitudinal and transverse stress decreased and the stress distribution, with different welding strength matching coefficients, was less diverse. After the load was released, longitudinal and transverse stress distribution for both path 1 and path 2 decreased to a low level. Cold stretching could reduce the effect of residual stress to various degrees. Transverse strain along the stretching direction was also taken into consideration. The experimental results validated the reliability of the partial simulation.

36 MATERIALS SCIENCE↗

Stress analysis of multilayered plates around circular holes

The elasticity problem for a thick plate consisting of two bonded dissimilar homogeneous layers is considered. It is assumed that the plate is infinite, contains a circular hole, and is subjected to axisymmetric external loads. A technique suitable to the formulation of three-dimensional boundary value problems is introduced and applied to the three-dimensional elasticity solution of an infinite plate with a hole. The effect of Poisson's ratio is studied in some detail, and the axisymmetric problem of a laminated plate is solved. The stresses at the interface are calculated and are observed to become unbounded at the hole boundary. An approximate treatment of the singularity is presented and the stress intensity factors are computed. Some of the results are compared with those found from the finite element method. The agreement between the two sets with regard to trend and magnitude is found to be very satisfactory.

Delale, F.↗

Equilibrium shape and location of a liquid drop acoustically positioned in a resonant rectangular chamber

The effect of a standing wave field in a rectangular chamber on the shape and location of an acoustically positioned drop or bubble is calculated. The sample deformation and equilibrium position are obtained from an analysis of the spherical harmonic projections of the total surface stress tensor. The method of calculation relies on the assumed condition that the sample is only slightly distorted from a spherical form. The equilibrium location of a levitated drop is combined with a formula introduced by Hasegawa (1979) to calcualte the ka dependence of the radiation force function. The present theory is valid for large as well as small ka values. Calculations in the small ka limit agree with previous theories and experimental results. Examples are presented for nonplane-wave modes as well as plane-wave rectangular modes.

Jackson, H. W.↗

Non-Classical Stress Concentration Behavior in a Radically Stretched Hyperelastic Sheet Containing a Circular Hole

Non-classical stress concentration behavior in a stretched circular hyperelastic sheet (outer radius b = 10 in., thickness t = 0.0625 in.) containing a central hole (radius a = 0.5 in.) was analyzed. The hyperelastic sheet was subjected to different levels of remote radial stretchings. Nastran large-strain large-deformation analysis and the Blatz-Ko large deformation theory were used to calculate the equal-biaxial stress concentration factors K. The results show that the values of K calculated from the Blatz-Ko theory and Nastran are extremely close. Unlike the classical linear elasticity theory, which gives the constant K = 2 for the equal-biaxial stress field, the hyperelastic K values were found to increase with increased stretching and can exceed the value K = 6 at a remote radial extension ratio of 2.35. The present K-values compare fairly well with the K-values obtained by previous works. The effect of the hole-size on K-values was investigated. The values of K start to decrease from a hole radius a = 0.125 in. down to K = 1 (no stress concentration) as a shrinks to a = 0 in. (no hole). Also, the newly introduced stretch and strain magnification factors {K(sub λ),K(sub ε) } are also material- and deformation-dependent, and can increase from linear levels of {1.0, 4.0} and reaching {3.07, 4.61}, respectively at a remote radial extension ratio of 2.35.

stress concentration↗

Simple spline-function equations for fracture mechanics calculations

The paper presents simple spline-function equations for fracture mechanics calculations. A spline function is a sequence of piecewise polynomials of degree n greater than 1 whose coefficients are such that the function and its first n-1 derivatives are continuous. Second-degree spline equations are presented for the compact, three point bend, and crack-line wedge-loaded specimens. Some expressions can be used directly, so that for a cyclic crack propagation test using a compact specimen, the equation given allows the cracklength to be calculated from the slope of the load-displacement curve. For an R-curve test, equations allow the crack length and stress intensity factor to be calculated from the displacement and the displacement ratio.

Orange, T. W.↗

Evolution of oceanic lithosphere - A driving force study of the Nazca plate

The role of the evolution of oceanic lithosphere in driving oceanic plates is tested with elastic and viscous finite element modelling of the Nazca plate. The results indicate that ridge-push forces, when distributed over that portion of the oceanic lithosphere giving rise to the force, predict a stress state that varies more spatially than does previous modelling with ridge forces concentrated at the ridge crest. In particular, the component of stress normal to the ridge vanishes near the ridge for the new modelling. Stress states have also been calculated for a variety of slab-pull models, which include possible dependence on age, rate, and angle of subduction. The predicted stresses vary substantially near the trench among the models with less variation farther from the trench.

Richardson, R. M.↗

Low Reynolds number multiple-time-scale turbulence model and calculations of steady and pulsating shear layers

A low Reynolds number multiple-time-scale turbulence model (LMS) and its application to fully developed turbulent channel flows and pulsating pipe flows are presented. The LMS can describe the inequilibrium turbulence phenomena down to the viscous sublayer. The calculated fluid flow and turbulence fields for the channel flows are in better agreement with the direct numerical simulation (DNS) results than those obtained using a Reynolds stress turbulence model, and the calculated near-wall dissipation rates are in qualitatively correct agreement with the DNS results. The LMS also successfully predicts the rapidly varying phase-lead of the wall shearing stress that occurs in a narrow range of the dimensionless frequency omega (+) = (omega x nu)/(upsilon x tau(exp2)) for the pulsating pipe flows while various other turbulence models fail to predict this phenomenon, and the LMS yields significantly improved numerical results for a wide range of the dimensionless frequency compared with those obtained using a rapid distortion theory (RDT).

Kim, Sang-Wook↗

Local instability of centrally loaded columns of channel section and Z-section

Charts are presented for the coefficients in formulas for the critical compressive stress at which cross-sectional distortion begins in a thin-wall member with either a channel section or a Z-section with identical flanges. The energy method of Timoshenko was used in the theoretical calculations required for the construction of the charts. The deflection equations were carefully selected to give good accuracy. The calculation of the critical compressive stress at stresses beyond the elastic range is briefly discussed. In order to demonstrate the use of the formulas and the charts in engineering calculations, two illustrative problems are included.

ELASTICITY↗

Phase field modeling of dislocations and obstacles in InSb

We present a phase-field dislocation dynamics (PFDD) model informed by first-principle calculations to elucidate the competitive dislocation nucleation and propagation between the glide and shuffle sets in InSb diamond cubic crystal. The calculations are directly informed with generalized stacking fault energy curves on the (111) slip plane for both the “glide set,” with the smaller interplanar spacing, and the “shuffle set,” with the larger interplanar spacing. The formulation also includes elastic anisotropy and the gradient term associated with the dislocation core. The PFDD calculations show that under no stress the equilibrium structure of screw glide set dislocations dissociates into Shockley partials, while those of the shuffle set dislocations do not dissociate, remaining compact. The calculated dislocation core widths of these InSb dislocations agree well with the measured values for other semiconductor materials, such as Si and GaN. We find that a shuffle set dislocation emits from a dislocation source at an applied stress about three times smaller than that needed to emit leading and trailing partials successively on the glide set plane. Once the partial dislocations in the glide set are emitted, they propagate faster than the shuffle set perfect dislocation at the same stress level.

36 MATERIALS SCIENCE↗

Power flows and Mechanical Intensities in structural finite element analysis

The identification of power flow paths in dynamically loaded structures is an important, but currently unavailable, capability for the finite element analyst. For this reason, methods for calculating power flows and mechanical intensities in finite element models are developed here. Formulations for calculating input and output powers, power flows, mechanical intensities, and power dissipations for beam, plate, and solid element types are derived. NASTRAN is used to calculate the required velocity, force, and stress results of an analysis, which a post-processor then uses to calculate power flow quantities. The SDRC I-deas Supertab module is used to view the final results. Test models include a simple truss and a beam-stiffened cantilever plate. Both test cases showed reasonable power flow fields over low to medium frequencies, with accurate power balances. Future work will include testing with more complex models, developing an interactive graphics program to view easily and efficiently the analysis results, applying shape optimization methods to the problem with power flow variables as design constraints, and adding the power flow capability to NASTRAN.

Hambric, Stephen A.↗

Comparison of experimental and theoretical thermal fatigue lives for five nickel base alloys

The alloys Nimonic 90, IN 100, coated IN 100, B 1900, coated B 1900, MAR M200, and MAR M200DS (directionally solidified) were studied. Maximum temperatures ranged from 770 C to 1120 C (1420 F to 2050 F). Specimen geometries included tapered disks, double-edged wedges, and cambered airfoils. The disks and wedges were heated and cooled in fluidized beds. The airfoil specimens were heated by a Mach 1 natural gas burner and rapid-air-cooled, with and without spanwise loading. Life calculations included two distinct failure modes: conventional low cycle fatigue and cyclic creep. Required material properties were limited to conventional thermal, tensile, and creep rupture data. The complete life calculation system included the calculation of transient temperature distributions, thermal strains, stresses, creep damage, fatigue damage, and cycles to first crack. Calculated lives were within a factor of two for 76 of the 86 data points analyzed. Cyclic creep accounted for 81% of all the calculated damage.

Spera, D. A.↗