Search NASA⌕ Search

SEARCH · Search NASA

Results for “Simulation Use Case”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

TH-A-9A-10: Prostate SBRT Delivery with Flattening-Filter-Free Mode: Benefit and Accuracy

Purpose: Flattening-filter-free (FFF) beam mode offered on TrueBeam™ linac enables delivering IMRT at 2400 MU/min dose rate. This study investigates the benefit and delivery accuracy of using high dose rate in the context of prostate SBRT. Methods: 8 prostate SBRT patients were retrospectively studied. In 5 cases treated with 600-MU/min dose rate, continuous prostate motion data acquired during radiation-beam-on was used to analyze motion range. In addition, the initial 1/3 of prostate motion trajectories during each radiation-beam-on was separated to simulate motion range if 2400-MU/min were used. To analyze delivery accuracy in FFF mode, MLC trajectory log files from an additional 3 cases treated at 2400-MU/min were acquired. These log files record MLC expected and actual positions every 20ms, and therefore can be used to reveal delivery accuracy. Results: (1) Benefit. On average treatment at 600-MU/min takes 30s per beam; whereas 2400-MU/min requires only 11s. When shortening delivery time to ~1/3, the prostate motion range was significantly smaller (p<0.001). Largest motion reduction occurred in Sup-Inf direction, from [−3.3mm, 2.1mm] to [−1.7mm, 1.7mm], followed by reduction from [−2.1mm, 2.4mm] to [−1.0mm, 2.4mm] in Ant-Pos direction. No change observed in LR direction [−0.8mm, 0.6mm]. The combined motion amplitude (vector norm) confirms that average motion and ranges are significantly smaller when beam-on was limited to the 1st 1/3 of actual delivery time. (2) Accuracy. Trajectory log file analysis showed excellent delivery accuracy with at 2400 MU/min. Most leaf deviations during beam-on were within 0.07mm (99-percentile). Maximum leaf-opening deviations during each beam-on were all under 0.1mm for all leaves. Dose-rate was maintained at 2400-MU/min during beam-on without dipping. Conclusion: Delivery prostate SBRT with 2400 MU/min is both beneficial and accurate. High dose rates significantly reduced both treatment time and intra-beam prostate motion range. Excellent delivery accuracy was confirmed with very small leaf motion deviation.

07 ISOTOPE AND RADIATION SOURCES↗

A comparison of electrostatic simulations to measurements of quantum dot structures.

We have compared simulations using solutions of Poisson's equation to detailed capacitance measurements on a double quantum dot structure. We tabulate the results and show which cases show good agreement and which do not. The capacitance values are also compared to those calculated by a solution of Laplace's equation. Electron density is plotted and discussed. In order to understand relevant potential barriers we compare simulations at 50 Kelvin to simulations at 15 Kelvin. We show that the charge density does not differ greatly, but that the conduction band potential does. However, a method of estimating the potential at 0 Kelvin based on the charge distribution at 50 Kelvin is shown to be close to the potential at 15 Kelvin. This method was used to estimate potential barriers at 0 Kelvin in two quantum dot structures.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A Data Library of Liquid Clouds Modelled With a Large Eddy Simulation Framework

We describe a library of atmospheric large eddy simulations (LES) of liquid-phase boundary layer clouds constructed to enable aerosol–cloud–turbulence interaction studies, support parameterization evaluation and development, and provide training data for machine learning applications. The simulations use a modern LES framework designed for high numerical accuracy, coupled to a detailed spectral bin microphysical scheme. Case studies are configured to represent observed conditions in four key global cloud regions—the Northeastern Atlantic, Northeastern Pacific, Continental United States and Southern Ocean—following a semi-idealised approach. The library also includes aerosol concentration halving and doubling experiments to expose the sensitivities of the case studies to aerosol perturbations. Simulation results are compared to observations on a case-by-case basis, then the library's coverage is evaluated in terms of spreads in meteorological factors and atmospheric boundary layer attributes.

aerosol↗

Strategies for simulating the time evolution of Hamiltonian lattice field theories

Simulating the time evolution of quantum field theories given some Hamiltonian H requires developing algorithms for implementing the unitary operator e -iHt . A variety of techniques exist that accomplish this task, with the most common technique used so far being Trotterization, which is a special case of the application of a product formula. However, other techniques exist that promise better asymptotic scaling in certain parameters of the theory being simulated, the most efficient of which are based on the concept of block encoding. In this work we study the performance of such algorithms in simulating lattice field theories. We derive and compare the asymptotic gate complexities of several commonly used simulation techniques in application to Hamiltonian lattice field theories. Using the scalar $\hat{φ}$ 4 theory as a test, we also perform numerical studies and compare the gate costs required by product formulas and signal-processing-based techniques to simulate time evolution. For the latter, we use the linear combination of unitaries (LCU) construction augmented with the quantum Fourier transform circuit to switch between the field and momentum eigenbases, which leads to immediate order-of-magnitude improvement in the cost of preparing the block encoding. Further, this paper also includes a pedagogical review of the techniques used, in particular product formulas, LCU, qubitization, quantum signal processing, as well as the technique for simulating geometrically-local Hamiltonians developed by Haah, Hastings, Kothari, and Low.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental and Theoretical Evaluation of Feed Flow Collar Design for Shell Fed Hollow Fiber Membrane Modules

An experimental and theoretical study of module collar design is presented here. Hollow fiber membranes are prepared by dip coating a poly(vinylidene) (PVDF) support with a polydimethylsiloxane (PDMS) gutter layer and a Pebax 2533 selective layer. Fiber bundles with a well-defined fiber packing are prepared using a 3D printed module. A parallel fiber bundle consisting of 4-9 uniformly spaced fibers is created with printed tabs that align the fibers and create a tubesheet. The tabs are sealed within a printed case that possesses a series of external ports for gas introduction and removal. Uniquely, both port location and the use of a collar to assist fluid distribution in the shell can be varied for the same fiber bundle. Experimental measurements are compared to computational fluid dynamics (CFD) simulations. The experimental module design allows high-fidelity representation of the fiber bundle and module case in the simulations. Comparisons between experiment and simulation are in good agreement over a broad range of experimental conditions. The detrimental effect of having ports located too close, leading to stagnation regions, is captured as well as the beneficial effects of using a collar for shell-side fluid distribution around the fiber bundle. Such results help validate the use of CFD to develop high-performance module designs.

Tran, Thien↗

A hydrological emulator for global applications – HE v1.0.0

Abstract. While global hydrological models (GHMs) are very useful in exploring water resources and interactions between the Earth and human systems, their use often requires numerous model inputs, complex model calibration, and high computation costs. To overcome these challenges, we construct an efficient open-source and ready-to-use hydrological emulator (HE) that can mimic complex GHMs at a range of spatial scales (e.g., basin, region, globe). More specifically, we construct both a lumped and a distributed scheme of the HE based on the monthly abcd model to explore the tradeoff between computational cost and model fidelity. Model predictability and computational efficiency are evaluated in simulating global runoff from 1971 to 2010 with both the lumped and distributed schemes. The results are compared against the runoff product from the widely used Variable Infiltration Capacity (VIC) model. Our evaluation indicates that the lumped and distributed schemes present comparable results regarding annual total quantity, spatial pattern, and temporal variation of the major water fluxes (e.g., total runoff, evapotranspiration) across the global 235 basins (e.g., correlation coefficient r between the annual total runoff from either of these two schemes and the VIC is >0.96), except for several cold (e.g., Arctic, interior Tibet), dry (e.g., North Africa) and mountainous (e.g., Argentina) regions. Compared against the monthly total runoff product from the VIC (aggregated from daily runoff), the global mean Kling–Gupta efficiencies are 0.75 and 0.79 for the lumped and distributed schemes, respectively, with the distributed scheme better capturing spatial heterogeneity. Notably, the computation efficiency of the lumped scheme is 2 orders of magnitude higher than the distributed one and 7 orders more efficient than the VIC model. A case study of uncertainty analysis for the world's 16 basins with top annual streamflow is conducted using 100 000 model simulations, and it demonstrates the lumped scheme's extraordinary advantage in computational efficiency. Our results suggest that the revised lumped abcd model can serve as an efficient and reasonable HE for complex GHMs and is suitable for broad practical use, and the distributed scheme is also an efficient alternative if spatial heterogeneity is of more interest.

Liu, Yaling↗

Impact of Carrier Concentration and Carrier Lifetime on MgZnO/CdSeTe/CdTe Solar Cells

Here, the performance impact of multiple parameters related to the use of MgZnO (MZO) as the emitter for bilayer CdSeTe/CdTe solar cells has been investigated in detail through numerical simulations. Such a comprehensive study is particularly important, because while cell fabrication using MZO has been highly successful in some cases, it has been less so in others, and it has not been clear which combinations of parameter values are most effective. The parameters considered here include the recombination velocity at the emitter/absorber interface, bulk recombination lifetime, and the carrier concentrations of the emitter and absorber. The ranges chosen for the simulation parameters are those most likely to be found experimentally. The primary finding is that independent of the interfacial recombination velocity and bulk recombination lifetime, the MZO carrier density should be > 1017 cm-3 and in any case greater than that of the absorber to reduce interface recombination. At the same time, a shallow dopant the order of 50 meV or less should reduce SRH recombination in the bulk and enable VOC > 1V.

14 SOLAR ENERGY↗

Sparse thermal data for cellular automata modeling of grain structure in additive manufacturing

Grain growth in the wake of the melt pool formed during alloy-based additive manufacturing (AM) is complex and multifaceted, depending on parameters governing heat transport, fluid flow, and solidification itself. Cellular automata (CA) models have proven effective in providing computationally efficient and physically sound predictions of grain structure for several AM problems, but their efficiency is tied to the performance of heat transport models. CA models use only a small portion of the problem's temperature data (near the moving melt pool boundary), and much of the CA calculations do not affect the final result due to re-melting of material. Coupling of and communication between heat transport and solidification models, and eliminating operations irrelevant towards final grain structure prediction, will be necessary for using these methods for efficient simulation of large parts. In this work, we introduce a procedure of decoupling the CA from temperature field simulation, using files of relevant temperature data written by the heat transport model. This approach is validated against the standard coupling approach using data obtained through the computational fluid dynamics software OpenFOAM. Negligible differences are seen in grain size, volume, and texture distributions for multilayer simulation of test problems, while the quantity of temperature data for these test problems was reduced by four orders of magnitude (from 100s of GB to 10s of MB) and the code performance sped up by a factor of around 50. Furthermore, variability in microstructure as a function of cell size, substrate, time step, and nucleation parameters is studied, and it is found that cell sizes less than or equal to 1.67 μm and sufficiently small time steps yield Αstatistically equivalent microstructures. Finally, a potential use case for this CA approach—the layer-wise convergence in grain structure starting from extremes in initial grain size—is examined. This approach's ability to simulate expected trends in nucleation and epitaxial grain growth for large regions of microstructure, simulated independently of heat transport models themselves, should prove useful for investigation of various microstructure uncertainties and prediction of part-scale experimental results.

36 MATERIALS SCIENCE↗

Effect of Anoxic Iron Corrosion on WIPP Brine Geochemistry FY23 Final Report (U)

A 280-day study was completed to evaluate the effect of zero-valent iron (Fe 0 ) on the Waste Isolation Pilot Plant (WIPP) brine geochemistry under anticipated reducing conditions. Hydrogen (H 2 ) gas is expected to be present in the repository after closure due to the anoxic corrosion of a vast quantity of iron contained in the waste forms disposed at WIPP; therefore, a background argon atmosphere containing H 2 was chosen for this study. WIPP groundwater brine pH and E h will impact the mobility and fate of plutonium within the repository. Modeling and laboratory results for Castile WIPP brine indicate that equilibrium fa values relative to the standard hydrogen electrode (SHE) are 40 mV more reducing (i.e., more negative) than those for Salado WIPP brine (-480 mV vs. -440 mV, respectively) because of the higher pH of the Castile brine (pH 9 .3 for Castile vs. pH 8.8 for Salado). The E h and pH data were corrected for the effects of high ionic strength. The experimental results for both brines are consistent with thermodynamic predictions using OLI Systems' Mixed Solvent Electrolyte chemical equilibrium model. The measured and corrected pH and E h data from this study are provided in Table ES-I and Table ES-2, respectively. The experimental study, with four test conditions in triplicate, was performed in a dual glovebox with a nominally 3 vol.% H 2 in argon atmosphere (target H 2 range: 3 ± I vol.%). Simulants containing MgO only ( experimental control) and MgO+Fe 0 (WIPP base case) were prepared for both the Salado and Castile brines. MgO was included in all simulants to account for the use of bulk magnesium oxide in the WIPP repository. Fe 0 was included in some simulants to incorporate the effects of the anoxic corrosion of iron and in-situ hydrogen generation in the study. The brine compositions were developed by Sandia National Laboratory (SNL; Xiong, 2008) and have been used in previous WIPP evaluations. The test method (agitation, etc.) is partially based on ASTM D3987-12. Twelve rounds of periodic measurements of pH and E h were performed over the course of the study. Chemical analysis results for liquids and solids (ICP-MS, ICP-ES, IC Anion, TIC, SEM-EDX) are consistent with the pH, E h , and thermodynamic modeling results. This study included the following conditions that deviate from anticipated post-closure conditions following brine intrusion, but were selected to facilitate bench-scale testing to validate modeling of pH and E h for the post-closure WIP P repository: an anoxic glove box atmosphere containing ≤ 4 vol. % H 2 vs. substantially higher H 2 gas concentrations assumed in the WIPP Performance Assessment (PA); a significantly higher liquid-to-solid test ratio compared to the much lower phase ratio anticipated in the WIP P repository; agitation of the simulant bottles to maximize mass transfer; and finally the use of Fe 0 reagents having a much greater surface area than expected in the WIP P repository. Non-representative conditions were chosen for various reasons such as: to provide bounding conservative results, to provide a margin of safety for testing, or to facilitate simulant sub-sampling and analysis. In a parallel effort, aqueous electrolyte thermodynamic models were developed for the synthetic Salado and Castile brines to inform the experimental design, facilitate laboratory data interpretation, and allow extension of evaluations beyond the parameters tested. Thermodynamic modeling simulations including the MgO and Fe 0 additives that are directly relevant to the experimental measurements (e.g., pH calibration curve, ORP corrections) are included in this report. The measured fa of the simulants was close to the OLI model predictions for both brines and was largely controlled by the background H 2 partial pressure in the vapor phase as well as H 2 generated in situ in the aqueous phase by the Fe 0 corrosion. The H 2 gas-phase concentration tested and thermodynamically evaluated was much lower than is assumed in the WIPP PA; however, H 2 (g) concentrations significantly below this level are still predicted to result in very reducing conditions. In conclusion: • The experimental results are consistent with thermodynamic model predictions for fa, pH, and the effects of high ionic strength. • Evidence to date suggests that the H2 concentration in the glovebox atmosphere ultimately determined the final E h values of the simulants and resulted in highly reducing conditions. As a result, little difference was observed between the control simulants containing only MgO and the WIPP base-case simulants that contained MgO and Fe 0 . • This test methodology is recommended for future studies evaluating WIPP repository conditions. The methodology includes: (1) background H 2 in argon with agitation ( or could alternatively include in-situ-generated H 2 in sealed bottles); (2) carefully measured and corrected ORP data ( with much effort focused on allowing the probes to fully stabilize); and (3) ionic-strength-corrected pH data. Other best practices, such as simulant sparging/handling, ORP probe replacement, etc., should also be considered. • The coupling of experimental studies and thermodynamic modeling is also highly recommended because these methods inform and direct one another leading to greater confidence in and understanding of the results.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Single–Column Model Simulations of Subtropical Marine Boundary–Layer Cloud Transitions Under Weakening Inversions

Results are presented of the GASS/EUCLIPSE single-column model inter-comparison study on the subtropical marine low-level cloud transition. A central goal is to establish the performance of state-of-the-art boundary-layer schemes for weather and climate models for this cloud regime, using large-eddy simulations of the same scenes as a reference. A novelty is that the comparison covers four different cases instead of one, in order to broaden the covered parameter space. Three cases are situated in the North-Eastern Pacific, while one reflects conditions in the North-Eastern Atlantic. A set of variables is considered that reflects key aspects of the transition process, making use of simple metrics to establish the model performance. Using this method some longstanding problems in low level cloud representation are identified. Considerable spread exists among models concerning the cloud amount, its vertical structure and the associated impact on radiative transfer. Here, the sign and amplitude of these biases differ somewhat per case, depending on how far the transition has progressed. After cloud breakup the ensemble median exhibits the well-known “too few too bright” problem. The boundary layer deepening rate and its state of decoupling are both underestimated, while the representation of the thin capping cloud layer appears complicated by a lack of vertical resolution. Encouragingly, some models are successful in representing the full set of variables, in particular the vertical structure and diurnal cycle of the cloud layer in transition. An intriguing result is that the median of the model ensemble performs best, inspiring a new approach in subgrid parameterization.

54 ENVIRONMENTAL SCIENCES↗

Mesoscale simulation of granular materials under weak shock compaction–pore size distribution effects

This research established a systematic method to generate various pore-size distributions (PSDs) and studied the effect of PSDs on the shock compaction response of granular materials using two-dimensional mesoscale simulations under identical porosity. Simulations utilized various PSDs for three particle shapes (circle, ellipse, and square). Contacting particle configurations using three PSDs, characterized by spatially uniform distributed pores to heterogeneous distributed pores, and non-contacting particle configurations under a single case of PSD were tested. The PSD of generated particle sets was characterized using coordination number, mean diameter, and bimodality coefficient as statistical metrics. Mesoscale simulations showed that regardless of the conditions of pore distributions, shock compaction of granular materials consistently demonstrates a precursor, shock compaction front, and end. However, the shock compaction velocity of contacting particles was dependent on the PSDs despite the constant initial porosity. The compaction velocity was faster in particle configurations with relatively uniform pore distributions than in heterogeneous pore distributions, which our study demonstrated can be attributed to particle rearrangement during compaction. Circular-shaped particles had high sensitivity in shock compaction response to the various PSDs. Furthermore, a contacting particle configuration tended to propagate the shock compaction wave relatively faster than particles that were in a non-contact configuration. This study established the relative importance of considering PSD as a metric over the coordination number in studies of the shock compaction response of granular materials. Further, insights are provided on the evolving shock substructure to characterize the shock compaction response of granular materials.

36 MATERIALS SCIENCE↗

Activity Diagrams for DEVS Models: A Case Study Modeling Health Care Behavior

Discrete Event Systems Specification (DEVS) is a widely used formalism for modeling and simulation of discrete and continuous systems. While DEVS provides a sound mathematical representation of discrete systems, its practical use can suffer when models become complex. Five main functions, which construct the core of atomic modules in DEVS, can realize the behaviors that modelers want to represent. The integration of these functions is handled by the simulation routine, however modelers can implement each function in various ways. Therefore, there is a need for graphical representations of complex models to simplify their implementation and facilitate their reproduction. In this work, we illustrate the use of activity diagrams for this purpose in the context of a health care behavior model, which is developed with an agent-based modeling paradigm.

Activity diagram↗

Modeling and simulation functional needs for molten salt reactor licensing

The modeling and simulation functional needs to license and design molten salt reactor concepts were assessed and an evaluation methodology was developed using a licensing-focused approach considering the modeling and simulation components that contribute to a molten salt reactor safety analysis report. These functional needs were prioritized by identifying the relationships between functional needs and using a quantitative weighting method to identify the most critical components to build a licensing case. This novel weighting method provided a list of functional needs prioritized relative to key advanced reactor licensing outcomes. In addition, functional need inputs were ranked to reveal those that feed the most modeling and simulation components. The findings from this prioritization effort were used to inform the modeling and simulation goals of the US Department of Energy Office of Nuclear Energy (DOE-NE) Molten Salt Reactor campaign.Modeling and simulation needs were grouped into three main categories: (1) source term definition, material accountancy, and radiological consequences, (2) safety analysis, and (3) steady-state neutronics and thermal hydraulics. Here, five near-term goals were identified among these focus areas that add value: (1) deploying a systems and safeguards analysis computational tool, (2) defining source terms for molten salt reactor analysis and interfacing with the US Nuclear Regulatory Commission on accident progression analysis, (3) developing point designs for liquid-fueled thermal-spectrum and fast-spectrum molten salt reactors, (4) building safety analysis specifications and reference solutions for Molten Salt Reactor Experiment transients, and (5) interfacing with the thermophysical and thermodynamic salt chemistry databases.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A Multiscale Model for the Quasi-Static Thermo-Plastic Behavior of Highly Cross-Linked Glassy Polymers

In this paper, we present experimentally validated molecular dynamics predictions of the quasi- static yield and post-yield behavior for a highly cross-linked epoxy polymer under gen- eral stress states and for different temperatures. In addition, a hierarchical multiscale model is presented where the nano-scale simulations obtained from molecular dynamics were homogenized to a continuum thermoplastic constitutive model for the epoxy that can be used to describe the macroscopic behavior of the material. Three major conclusions were achieved: (1) the yield surfaces generated from the nano-scale model for different temperatures agree well with the paraboloid yield crite- rion, supporting previous macroscopic experimental observations; (2) rescaling of the entire yield surfaces to the quasi-static case is possible by considering Argon’s theoretical predictions for pure compression of the polymer at absolute zero temperature; (3) nano- scale simulations can be used for an experimentally-free calibration of macroscopic con- tinuum models, opening new avenues for the design of materials and structures through multi-scale simulations that provide structure-property-performance relationships.

36 MATERIALS SCIENCE↗

Financial Analysis of the High Flow Experiment conducted at the Glen Canyon Dam during Water Year 2023

The Glen Canyon Dam (GCD) is a Colorado River Storage Project (CRSP) power resource that is a component of the Salt Lake City Area Integrated Projects (SLCA/IP). The 2016 record of decision (ROD) for the GCD long-term experimental and management plan (LTEMP) final Environmental Impact Statement (EIS) specified criteria for GCD monthly water releases, daily and hourly operating limits, and experimental releases. This report examines the financial implications of the high flow experiment (HFE) conducted at GCD during the spring of Water Year (WY) 2023 as required by the LTEMP HFE Protocol. This report is part of a series of reports that describe the financial costs of LTEMP experimental releases since the 2016 ROD was adopted in January 2017. Previous reports analyzed the impact of several past HFEs and Bug Flow Experiments. This report focuses on the HFE conducted in April 2023. For this experimental release, financial costs of approximately $1.33 million were incurred because the HFE required sustained water releases exceeding the power plant’s maximum turbine flow rate. In addition, during the experiment, operators were not allowed to shape GCD power production, either to follow Firm Electric Service (FES) customer day-ahead energy deliveries or to respond to market prices. This study identifies the main factors contributing to the HFE costs and examines the interdependencies among these factors. It applies an integrated set of tools to estimate Western Area Power Administration (WAPA) financial impacts by simulating GCD under two types of cases; namely, (1) a “With Experiment” case that mimics the operations that actually occurred and (2) a “Without Experiment” case that simulates operations under the assumption that the HFE did not occur. The “With Experiment” case mimics operations during the HFE and the entire month the HFE occurred. It complies with LTEMP hourly and daily operating criteria. The “Without Experiment” case assumes that the HFE did not occur. The monthly water release volume is assumed to be identical under both cases. The Colorado River Storage Project Python-based model (CRiSPPy) model was the main modeling tool used to simulate the dispatch of the GCD hydropower plant and associated water releases from Lake Powell. In the modeling process, the research team used extensive data sets and historical information on SLCA/IP power plant characteristics, hydrologic conditions, and WAPA’s power purchases and sales prices. In addition to estimating the financial impact of the HFE, the team used the CRiSPPy model to gain insights into the interplay among ROD operating criteria, exceptions made to criteria to accommodate the HFE, and WAPA operating practices.

13 HYDRO ENERGY↗

A Lagrangian model for laser-induced fluorescence and its application to measurements of plasma ion temperature and electrostatic waves

Extensive information can be obtained on wave-particle interactions and wave fields by a direct measurement of perturbed ion distribution functions using laser-induced fluorescence (LIF). For practical purposes, LIF is frequently performed on metastable states that are produced from neutral gas particles and ions in other electronic states. If the laser intensity is increased to obtain a better LIF signal, then optical pumping can produce systematic effects depending on the collision rates which control metastable population and lifetime. We numerically simulate the ion velocity distribution measurement and wave-detection process using a Lagrangian model for the LIF signal for the case where metastables are produced directly from neutrals. This case requires more strict precautions and is important for discharges with energetic primary electrons and a high density of neutrals. Some of the results also apply to metastables produced from pre-existing ions. The simulations show that optical pumping broadening affects the ion velocity distribution function f 0 (v) and its first-order perturbation f 1 (v,t) when the laser intensity is increased above a certain level. The results also suggest that ion temperature measurements are only accurate when the metastable ions can live longer than the ion-ion collision mean free time. For the purposes of wave detection, the wave period has to be significantly shorter than the lifetime of metastable ions for a direct interpretation. It is more generally true that metastable ions may be viewed as test-particles. Finally, as long as an appropriate model is available, LIF can be extended to a range of environments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Gyrokinetic simulations of reverse shear Alfven eigenmodes in DIII-D plasmas

A gyrokinetic ion/mass-less fluid electron hybrid model as implemented in the GEM code [Y. Chen and S. E. Parker, J. Comput. Phys. 220, 837 (2007)] is used to study the reverse shear Alfven eigenmodes (RSAE) observed in DIII-D, discharge no. 142111. This is a well diagnosed case with measurement of the core-localized RSAE mode structures and the mode frequency, which can be used to compare with simulations. Simulations reproduce many features of the observation, including the mode frequency up-sweeping in time and the sweeping range. A new algorithmic feature is added to the GEM code for this study. Instead of the gyrokinetic Poisson equation itself, its time derivative, or the vorticity equation, is solved to obtain the electric potential. This permits a numerical scheme that ensures the E Multiplication-Sign B convection of the equilibrium density profiles of each species cancel each other in the absence of any finite-Larmor-radius effects. These nonlinear simulations generally result in an electron temperature fluctuation level that is comparable to measurements, and a mode frequency spectrum broader than the experimental spectrum. The spectral width from simulations can be reduced if less steep beam density profiles are used, but then the experimental fluctuation level can be reproduced only if a collision rate above the classical level is assumed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Inversion of downhole electrical measurements for proppant mapping using very fast simulated annealing

Proppant mapping is critical for optimizing fracture treatment design and improving wells’ productivity. An electrode-based resistivity tool concept was developed earlier for proppant mapping in cased-hole wells. An array of insulating gaps is installed and cemented in place as a permanent part of the casing string. The electrical measurements are performed by imposing a voltage across each insulating gap, one at a time, before and after hydraulic fracture operations. The voltages across other insulating gaps near the transmitter gap are recorded. The method relies on direct excitation of the casing, which is expected to overcome the severe limitations of induction tools in cased-hole wells. A forward model based on a finite volume method has been developed to simulate the tool’s response to one or multiple fractures. To enable the implementation of such a practical system in multistage fractured horizontal wells, a fast and robust inversion approach is required. To that end, we have developed a divide-and-conquer approach based on a global optimization algorithm very fast simulated annealing (VFSA). Specifically, the original inverse problem is divided into subproblems and each subproblem can be solved separately using VFSA. The results indicate that our approach can invert the data and output widths and radii of multiple fractures without requiring a large number of forward simulations. The robustness of the inverse solver is also tested by adding Gaussian noise to the synthetic data. We tested example cases that demonstrate that when up to 5% noise is introduced, VFSA still provides very accurate inversion results with moderate uncertainties. Inversion results with some more realistic conditions, e.g., tilted fractures, complex fractures, and so on, are also presented.

Geochemistry & Geophysics↗