Search NASA⌕ Search

SEARCH · Search NASA

Results for “compressor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS1951

Calculated performance of a mercury-compressor-jet powered airplane using a nuclear reactor as an energy source

An analysis was made at a flight Mach number of 1.5, an altitude of 45,000 feet, a turbine-inlet temperature of 1460 degrees R, of a mercury compressor-jet powered airplane using a nuclear reactor as an energy source. The calculations covered a range of turbine-exhaust and turbine-inlet pressures and condenser-inlet Mach numbers. For a turbine--inlet pressure of 40 pounds per square inch absolute, a turbine-exhaust pressure of 14 pounds per square inch absolute, and a condenser-inlet Mach number of 0.23 the calculated airplane gross weight required to carry a 20,000 pound payload was 322000 pounds and the reactor heat release per unit volume was 8.9 kilowatts per cubic inch. These do not represent optimum operating conditions.

MERCURY↗
NASA NTRS1951

Some effects of blade trailing-edge thickness on performance of a single-stage axial-flow compressor

A set of modified NACA 65-series blower blades designed for axial inlet velocity, high inlet Mach number, and high blade loading was investigated for trailing-edge thickness of 0.015, 0.030, and 0.045 inch to determine the effect of trailing-edge thickness on single-stage axial-flow-compressor performance. Trailing-edge thickness effects were small except at the highest tip speed investigated (915 ft/sec). Trailing-edge thickness up to 30 percent of maximum blade thickness were used without sacrifice of performance of NACA 65-series blades.

AIRFOILS - THICKNESS↗
NASA NTRS1953

Investigation of Turbines for Driving Supersonic Compressors III : First Configuration with Four Nozzle Settings and One Nozzle Modification

A turbine designed to power a supersonic compressor was investigated with four nozzle settings and one nozzle modification to determine the effect on turbine performance. With the correct ratio of nozzle throat area to rotor effective throat area, the design specific work was obtained near the peak efficiency. From the results of the investigation it was concluded that the convex in sweep of the rotor inner wall and high degree of blade taper caused the turbine configuration to have two aerodynamic disadvantages in comparison with a turbine configuration with an axial inner wall at the rotor outlet and little axial taper.

TURBINES - MIXED-FLOW↗
NASA NTRS1953

Analysis of turbine stator adjustment required for compressor design-point operation in high Mach number supersonic turbojet engines

For turbojet engines designed for flight Mach numbers of 2.5 and 3.0, use of turbine stator adjustment to maintain compressor design-point operation was evaluated analytically to determine the effect on the aerodynamics of the turbine. Since the effect of turbine stator adjustment is to make the turbine design sensitive to the particular engine design conditions selected, in some cases the turbine must be conservatively designed for the high-speed flight condition to assure satisfactory turbine performance at take-off. A new concept, the break-even point, is introduced to provide quick evaluation of the proximity of turbines to the blade-loading limit at any off-design operation.

ENGINES, CONTROL - TURBOJET↗
NASA NTRS1955

A survey of unclassified axial-flow-compressor literature

A survey of unclassified axial-flow-compressor literature is presented in the form of brief reviews of the methods, results, and conclusions of selected reports. The reports are organized into several main categories with subdivisions, and frequent references are made within the individual reviews to pertinent material elsewhere in the survey.

Herzig, Howard Z↗
NASA NTRS1957

Identification of Foreign Objects Damaging Compressor Blades in Turbojet Engines

Damage to the compressor blades of turbojet engines due to ingestion of foreign objects is a growing problem, the solution of which has been made more difficult by the large percentage of damaging materials that have remained unknown. A rapid emission spectroscopic method was devised to identify the chemical composition of these foreign objects. Results on laboratory-prepared specimens and blades from damaged engines show that the method can be utilized to determine the nature of the ingested foreign objects.

Spakowski, A E↗
NASA NTRS1956

Investigation of Two-Stage Counterrotating Compressor. III: Design of Second-Stage Rotor and Preliminary Over-All Performance

At the design speed of a two-stage counterrotating compressor, an overall average pressure ratio of 4.3 was obtained at a specific weight flow of 27.2 pounds per second per square foot frontal area with an adiabatic efficiency of 0.75. Preliminary tests indicate that a weight-flow mismatching exists between the two rotors that causes the first rotor to operate at less than peak efficiency at design speed. At lower speeds, the first stage was forced to operate in the stalled region in single-stage tests. With the second rotor installed, no periodic rotating stall was observed, although random fluctations of similiar magnitude were noted.

Wilcox, Ward W↗
NASA NTRS1956

Experimental Investigation of a Five-stage Axial-flow Research Compressor with Transonic Rotors in All Stages III : Interstage Data and Individual Stage Performance Characteristics

For use in computing the detailed performance parameters of individual blade rows of a multistage compressor, radial distributions of total pressure, total temperature, static pressure and air-flow angle are tabulated. The data cover a range of air flow from choke to the approximate surge limit for equivalent rotor speeds from 70 to 100 percent of design. Equivalent stage performance curves determined from the radial survey measurements indicate both the individual performance and the matching of the stages at the speeds investigated.

Sandercock, Donald M↗
NASA NTRS1950

Application of radial-equilibrium condition to axial-flow compressor and turbine design

Basic general equations governing the three-dimensional compressible flow of gas through a compressor or turbine are given in terms of total enthalpy, entropy, and velocity components of the gas. Two methods of solution are obtained for the simplified, steady axially symmetric flow; one involves the use of a number of successive planes normal to the axis of the machine and short distances apart, and the other involves only three stations for a stage in which an appropriate radial-flow path is used. Methods of calculation for the limiting cases of zero and infinite blade aspect ratios and an approximate method of calculation for finite blade aspect ratio are also given. In these methods, the blade loading and the shape of the annular passage wall may be arbitrarily specified.

Wu, Chung-Hua↗
NASA NTRS1947

Investigation of Axial-flow Fan and Compressor Rotors Designed for Three-dimensional Flow

An investigation has been conducted to determine whether three-dimensional flows may be utilized in axial-flow fan and compressor rotors so that the spanwise load distribution may be varied to obtain high pressure rise. Two rotors, one with approximately uniform and one with solid-body downstream tangential-velocity distributions, were designed and tested at the design blade angle. Radial surveys of total pressure, static pressure, and flow angle were made upstream and downstream of the test rotors through a quantity-coefficient range. Tests of the solid-body rotor were also conducted at a large value of tip clearance. The results indicated that the three-dimensional flows may be utilized with high efficiency and that the three-dimensional theory used in conjunction with two-dimensional cascade data is sufficiently accurate for design purposes. The tests also showed that the tip-clearance losses of rotors highly loaded at the tips are not excessive. The existing three-dimensional theory in simplified for and an illustrative rotor design are presented in appendixes.

Kahane, A↗
NASA NTRS1994

System Measures Pressures Aboard A Compressor Rotor

Rotating pressure-measuring instrumentation includes on-board calibration standard. Computer-controlled, multichannel instrumentation system acquires pressure measurements from sensors mounted in 1.52-m-diameter rotor of compressor. Includes 5 miniature, electronically scanned pressure (ESP) modules, each containing 48 piezoresistive pressure sensors, pneumatic calibration valve, and electronic circuits for addressing and amplifying output of each sensor. Modules mounted on centerline of rotor, on instrumentation tower located inside nose cone of rotor. Subsystem designed to convert analog signal to distinct frequency without significantly affecting accuracy.

Freedman, Robert J.↗
NASA NTRS1994

Piston-Skirt Lubrication System For Compressor

Piston-skirt lubrication system provides steady supply of oil to piston rings of gas compressor. No need for oil-filled crankcase or external oil pump. Instead, part of each piston acts as its own oil pump circulating oil from reservoir. Annular space at bottom of piston and cylinder constitutes working volume of small oil pump. Depending on application, reservoir open to atmosphere, or sealed and pressurized in bellows to prevent contact between oil and atmosphere. Filter removes particles worn away from piston rings and cylinder wall during normal operation.

Schroeder, Edgar C.↗
NASA NTRS1995

Enhanced capabilities and modified users manual for axial-flow compressor conceptual design code CSPAN

Modifications made to the axial-flow compressor conceptual design code CSPAN are documented in this report. Endwall blockage and stall margin predictions were added. The loss-coefficient model was upgraded. Default correlations for rotor and stator solidity and aspect-ratio inputs and for stator-exit tangential velocity inputs were included in the code along with defaults for aerodynamic design limits. A complete description of input and output along with sample cases are included.

Glassman, Arthur J.↗
NASA NTRS1995

The effect of adding roughness and thickness to a transonic axial compressor rotor

The performance deterioration of a high speed axial compressor rotor due to surface roughness and airfoil thickness variations is reported. A 0.025 mm (0.001 in.) thick rough coating with a surface finish of 2.54-3.18 RMS microns (100-125 RMS microinches) is applied to the pressure and suction surface of the rotor blades. Coating both surfaces increases the leading edge thickness by 10% at the hub and 20% at the tip. Application of this coating results in a loss in efficiency of 6 points and a 9% reduction in the pressure ratio across the rotor at an operating condition near the design point. To separate the effect of thickness and roughness, a smooth coating of equal thickness is also applied to the blade. The smooth coating surface finish is 0.254-0.508 RMS microns (10-20 RMS microinches), compared to the bare metal blade surface finish of 0.508 RMS microns (20 RMS microinches). The smooth coating results in approximately half of the performance deterioration found from the rough coating. Both coatings are then applied to different portions of the blade surface to determine which portions of the airfoil are most sensitive to thickness/roughness variations. Aerodynamic performance measurements are presented for a number of coating configurations at 60%, 80%, and 100% of design speed. The results indicate that thickness/roughness over the first 10% of blade chord accounts for virtually all of the observed performance degradation for the smooth coating, compared to about 70% of the observed performance degradation for the rough coating. The performance deterioration is investigated in more detail at design speed using laser anemometer measurements as well as predictions generated by a quasi-3D Navier-Stokes flow solver which includes a surface roughness model. Measurements and analysis are performed on the baseline blade and the full-coverage smooth and rough coatings. The results indicate that coating the blade causes a thickening of the blade boundary layers. The interaction between the rotor passage shock and the thickened suction surface boundary layer then results in an increase in blockage which reduces the diffusion level in the rear half of the blade passage, thus reducing the aerodynamic performance of the rotor.

Suder, Kenneth L.↗
NASA NTRS1995

Experimental and Computational Investigation of the Tip Clearance Flow in a Transonic Axial Compressor Rotor

Experimental and computational techniques are used to investigate tip clearance flows in a transonic axial compressor rotor at design and part speed conditions. Laser anemometer data acquired in the endwall region are presented for operating conditions near peak efficiency and near stall at 100% design speed and at near peak efficiency at 60% design speed. The role of the passage shock/leakage vortex interaction in generating endwall blockage is discussed. As a result of the shock/vortex interaction at design speed, the radial influence of the tip clearance flow extends to 20 times the physical tip clearance height. At part speed, in the absence of the shock, the radial extent is only 5 times the tip clearance height. Both measurements and analysis indicate that under part-speed operating conditions a second vortex, which does not originate from the tip leakage flow, forms in the endwall region within the blade passage and exits the passage near midpitch. Mixing of the leakage vortex with primary flow downstream of the rotor at both design and part speed conditions is also discussed.

Suder, Kenneth L.↗
NASA NTRS1995

Better Gas-Gap Thermal Switches For Sorption Compressors

Gas-gap thermal switches associated with sorption compressors of some heat pumps and cryogenic systems designed for higher performance, according to proposal, by introducing controlled turbulent flows into gas gaps. Utilizes convection in turbulent flow to transfer heat at greater rate. Design takes advantage of flow of working fluid. Working fluid also serve as heat transfer medium in gas gap.

Bhandari, Pradeep↗