Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Dislocation loop evolution during in-situ ion irradiation of model FeCrAl alloys

Model FeCrAl alloys of Fe-10%Cr-5%Al, Fe-12%Cr-4.5%Al, Fe-15%Cr-4%Al, and Fe-18%Cr-3%Al (in wt %) were irradiated with 1 MeV Kr++ ions in-situ with transmission electron microscopy to a dose of 2.5 displacements per atom (dpa) at 320 °C. In all cases, the microstructural damage consisted of dislocation loops with ½< 111 > and <100 > Burgers vectors. The proportion of ½< 111 > dislocation loops varied from ~50% in the Fe-10%Cr-5%Al model alloy and the Fe-18Cr%-3%Al model alloy to a peak of ~80% in the model Fe-15%Cr-4.5%Al alloy. The dislocation loop volume density increased with dose for all alloys and showed signs of approaching an upper limit. The total loop populations at 2.5 dpa had a slight (and possibly insignificant) decline as the chromium content was increased from 10 to 15 wt %, but the Fe-18%Cr-3%Al alloy had a dislocation loop population ~50% smaller than the other model alloys. As a result, the largest dislocation loops in each alloy had image sizes of close to 20 nm in the micrographs, and the median diameters for all alloys ranged from 6 to 8 nm. Nature analysis by the inside-outside method indicated most dislocation loops were interstitial type.

36 MATERIALS SCIENCE↗

Emulation of neutron-irradiated microstructure of austenitic 21Cr32Ni model alloy using dual-ion irradiation

Here, in this study, the capability of heavy-ion irradiation to emulate neutron irradiation was demonstrated on an austenitic 21Cr32Ni type ternary model alloy. The model alloy used in this study is chemically analogous but compositionally simpler than of alloy 800H, which is a candidate austenitic Ni alloy which has been proposed for use in Generation IV reactors. The microstructure of the 21Cr32Ni model alloy irradiated in the BOR-60 fast reactor to 17.1 dpa and 35 dpa at ~380°C was characterized using transmission electron microscopy (TEM). The 17.1 dpa BOR-60 irradiated microstructure was then compared with the microstructure of the same material developed under dual-ion (DI) irradiation using various He/dpa ratios between 0.1 and 16.6 appm He/dpa in the temperature range of 430°C-500°C. The results showed that both neutron and DI irradiation of 21Cr32Ni model alloy produced dislocations in the form of a dislocation network as well as {111}-type faulted dislocation loops, cavities, and radiation-induced Ni enrichment at radiation-induced sinks. When the dose and the He/dpa ratio were kept similar to those in neutron irradiation, DI irradiation of the 21Cr32Ni model alloy at 460°C resulted in over-nucleation of small cavities and in a high density of faulted dislocation loops compared to those observed in the fast-neutron irradiated alloy of the same heat irradiated at ~380°C. The optimal condition for reproducing the neutron-irradiated microstructure was DI irradiation at 460°C and 0.1 appm He/dpa. In that case, the faulted loop and cavity size distributions in the BOR-60 irradiated 21Cr32Ni model alloy samples closely matched with those measured in the DI irradiated 21Cr32Ni model alloy sample. The fact that the He/dpa is an order of magnitude smaller than the helium generation rate for fast neutron irradiation, stops over nucleation and allows for the development of a similar microstructure as for neutron irradiation.

21Cr32Ni model alloy↗

Microstructure Evolution during Cold Rolling in a Nanocrystalline Ni-Fe Alloy Determined by Synchrotron X-ray Diffraction

Stress softening after cold rolling is observed in an electrodeposited nanocrystalline Ni-Fe alloy. The grain-size distribution becomes much broader after the cold rolling. Microstructure changes, though moderate, such as simultaneously decreased dislocation and twin densities with grain growth during cold rolling, are systematically proved by synchrotron high-energy X-ray diffraction, and transmission-electron microscopy and differential-scanning calorimetry (DSC). The amorphous fractions in the form of grain boundaries are evidenced by the diffuse-background scatterings and large DSC values. Partial dislocation separation calculation, a dislocation mean free path and annihilation model, and texture development together reveal that the current nanocrystalline Ni-Fe alloy exhibits the combined behavior of perfect dislocation slip and grain-boundary mediated deformation.

43 PARTICLE ACCELERATORS↗

Defects, strain relaxation, and compositional grading in high indium content InGaN epilayers grown by molecular beam epitaxy

We investigate the structural properties of a series of high alloy content InGaN epilayers grown by plasma-assisted molecular beam epitaxy, employing the deposition temperature as variable under invariant element fluxes. Using transmission electron microscopy methods, distinct strain relaxation modes were observed, depending on the indium content attained through temperature adjustment. At lower indium contents, strain relaxation by V-pit formation dominated, with concurrent formation of an indium-rich interfacial zone. With increasing indium content, this mechanism was gradually substituted by the introduction of a self-formed strained interfacial InGaN layer of lower indium content, as well as multiple intrinsic basal stacking faults and threading dislocations in the rest of the film. We show that this interfacial layer is not chemically abrupt and that major plastic strain relaxation through defect introduction commences upon reaching a critical indium concentration as a result of compositional pulling. Upon further increase of the indium content, this relaxation mode was again gradually succeeded by the increase in the density of misfit dislocations at the InGaN/GaN interface, leading eventually to the suppression of the strained InGaN layer and basal stacking faults.

36 MATERIALS SCIENCE↗

Modeling and Simulation of Microstructure Evolution and Deformation in an Irradiated Environment

The ability to predict the behavior of structural components in a nuclear power plant is critical to the nuclear industry. Structural metals in the primary loop of nuclear power plants must endure challenges such as irradiation and mechanical and thermal loading, and these structural metal components must continue to function in potential transient and accident conditions throughout the operational lifetime of the power plant. This extreme operational environment changes the metal microstructure by creating additional defects. The physical interactions of dislocations with these defects govern how the metal will respond to future conditions. Therefore predicting the mechanical response of these metals requires a set of physically based and reliable models of dislocation and defect interactions. These microstructure elements include glide mobile and immobile dislocations, geometrically necessary dislocations, twinning dislocations, irradiation defects, and thermal aging defects. We present here a continuum dislocation dynamics crystal plasticity framework to capture the interaction mechanisms of these dislocations and defects, verified with a combination of benchmark problems and comparisons with experimental data for two different types of structural metals: alpha iron and nickel-based alloys. In our simulations of $\alpha$ iron we highlight the advantages of applying a Monte Carlo stochastic model of cross slip dislocation motion and show the importance of capturing the 3D nature of glide dislocation and self-interstitial atom loop radiation defect interactions. We demonstrate coupling of glide dislocations with geometrically necessary dislocations to capture the influence of lattice bending, including the sensitivity of the geometrically necessary dislocations to changes in the grain boundary angle. We further examine the interaction of glide dislocations with the twin dislocations and thermally aged defects which have been observed in a nickel-based alloy with additional models. Finally we assess the reliability of this crystal plasticity framework by comparing two dislocation glide velocity models across the range of normal operation temperatures. In successfully applying our crystal plasticity framework to multiple metals, we provide further evidence of the reliability of our approach. The results of this mechanism-based continuum dislocation dynamics crystal plasticity framework can be used to inform engineering scale models throughout the nuclear industry.

36 MATERIALS SCIENCE↗

Linear complexions enable unprecedented ductility retention in neutron irradiated ferritic steel

Herein, the operando formation of Si-enriched linear complexions during neutron irradiation enables Grade 91 ferritic steel to overcome the strength–ductility tradeoff, one of the most critical life-limiting challenges facing nuclear structural alloys. Linear complexions are a distinct yet confined chemical and structural state at a dislocation, which are rarely reported in engineering alloys. Ferritic steels are amongst the most ubiquitous engineering alloys for current and future nuclear components, but they are susceptible to irradiation hardening and embrittlement. Here, exceptional ductility retention exceeding 90% of pre-irradiation levels is obtained in Grade 91 synthesized using powder metallurgy with hot isostatic pressing (PM-HIP). Powder processing artifacts promote a high density of screw dislocation arrays, on which β-FeSi 2 linear complexions form due to Si segregation during irradiation. Screw dislocation dipoles undergo pinning and unpinning on linear complexions, resulting in extended yielding and significant ductility retention post-irradiation. These findings represent a significant advancement toward design of alloys and manufacturing processes that can autonomously self-regulate their microstructural resilience in-operando during irradiation, enabling exceptional ductility rather than embrittlement.

Chatterjee, Arya [University of Illinois, Urbana, ↗

Nucleation Mechanism of 6H-SiC Polytype Inclusions Inside 15R-SiC Crystals

A model is presented for the nucleation mechanism of 6H-SiC polytype inclusions inside 15R-SiC boules. Inhomogeneous densities of screw dislocations lead to uneven growth rates, resulting in complex step overgrowth processes which can partially suppress the Burgers vector of a 15R 1c screw dislocation through the creation of Frank faults and Frank partial dislocations. Combined with stacking shifts induced by the passage of basal plane partial dislocations, it is shown that the partial Burgers vector suppression can leave behind a residual 6H 1c dislocation, which then acts as a nucleus for reproduction of 6H-SiC structure in the 15R-SiC crystal.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Formation of Lamellar Carbides in Alloy 617-HAZ and Their Role in the Impact Toughness of Alloy 617/9%Cr Dissimilar Welded Joint

The relationship between the microstructure and impact toughness, especially the formation of the lamellar carbides and its effect on the impact toughness of the heat-affected zone of Alloy 617 (Alloy 617-HAZ), was systematically investigated. Impact test was performed on Alloy 617/9%Cr dissimilar welded joints aged for different time at 620 °C. The results showed that the characteristic zones of the whole welded joint revealed decreased impact toughness with increasing the aging time. The impact energies in weld metal showed high stability despite the aging process, while the Alloy 617-HAZ for all testing specimens presented the lowest impact toughness with various aging time. Meanwhile, the mixed grains were found in the base metal (BM) and heat-affected zone of Alloy 617, together with the twins with different widths located in the interior of the large grains. The columnar and equiaxed grain zones appear alternately due to the multilayer and multi-pass welding technique. In particular, compared with Alloy 617-BM, coarsened and even lamellar carbides were observed in Alloy 617-HAZ. These special carbides can separate the grains and therefore result in the formation of intergranular fracture morphology in Alloy 617-HAZ. Besides, the microhardness distribution was tested with a proper load, and the results exhibited that the weld possessed the highest hardness for all specimens with various aging time. The higher microhardness in Alloy 617-HAZ compared with that in Alloy 617-BM was attributed to the high density of the dislocations, which could be detected by transmission electron microscope. As a result, the coarsened carbides aggregated in the grain boundaries to form the lamellar layer are deemed as the main factor to reduce the impact toughness in Alloy 617-HAZ.

36 MATERIALS SCIENCE↗

Crystal plasticity investigation of the microstructural factors influencing dislocation channeling in a model irradiated bcc material

We use a continuum crystal plasticity framework to study the effect of microstructure and mesoscopic factors on dislocation channeling and flow localization in an irradiated model bcc alloy. For simulated dislocation channeling characteristics we correlate the dislocation and defect densities in the substructure, local Schmid factor, and stress triaxiality, in terms of their temporal and spatial evolution. A metric is introduced to assess the propensity for localization and is correlated to the grain-level Schmid factor. We also found that localization generally takes place in grains with a local Schmid factor in the range 0.42 or higher. Surface slip step heights are computed at free surfaces and compared to relevant experiments.

36 MATERIALS SCIENCE↗

Thermal activation parameters of plastic flow reveal deformation mechanisms in the CrMnFeCoNi high-entropy alloy

To reveal the operating mechanisms of plastic deformation in an FCC high-entropy alloy, the activation volumes in CrMnFeCoNi have been measured as a function of plastic strain and temperature between 77 K and 423 K using repeated load relaxation experiments. At the yield stress, σ y , the activation volume varies from ~60 b3 at 77 K to ~360 b 3 at 293 K and scales inversely with yield stress. With increasing plastic strain, the activation volume decreases and the trends follow the Cottrell-Stokes law, according to which the inverse activation volume should increase linearly with σ - σ y (Haasen plot). This is consistent with the notion that hardening due to an increase in the density of forest dislocations is naturally associated with a decrease in the activation volume because the spacing between dislocations decreases. The values and trends in activation volume agree with theoretical predictions that treat the HEA as a high-concentration solid-solution-strengthened alloy. Lastly, these results demonstrate that this HEA deforms by the mechanisms typical of solute strengthening in FCC alloys, and thus indicate that the high compositional/structural complexity does not introduce any new intrinsic deformation mechanisms.

36 MATERIALS SCIENCE↗

Microstructures of ZnO films deposited on (0001) and r-cut α-Al2O3 using metal organic chemical vapor deposition

Zinc oxide films were deposited on (0001) and r-cut α-Al2O3 under identical conditions using metal organic chemical vapor deposition. Microstructures of the ZnO films were studied in detail using conventional and high-resolution transmission electron microscopy (HRTEM), electron diffraction, and HRTEM image simulations. The films deposited on these two substrates show distinctive structural differences. The film grown on r-cut α-Al2O3 shows a high quality single crystal with an orientation relationship of α-Al2O3[-101-1]//ZnO[0001] and α-Al2O3(10-1-2)//ZnO(2-1-10). The interface between the film and the substrate was abrupt and decorated with high density of misfit dislocations. Film grown on α-Al2O3 (0001) shows several orientation domains. Typically, one domain correspond to the classic growth model such that α-Al2O3 (0001)//ZnO(0001) and α-Al2O3 [11-20]//ZnO[10-10]. Another domain corresponds to the growth mode such that α-Al2O3 [11-20]//ZnO[10-10] but the (0001) plane of ZnO is tilted relative to the (0001) plane of α-Al2O3 such that ZnO(0001) is almost parallel to the α-Al2O3 (-1104) plane. This orientation reduces the extent of lattice mismatch as compared with the classic growth mode. The interface between ZnO and α-Al2O3 is abrupt and possesses periodic dislocations.

36 MATERIALS SCIENCE↗

Growth study of nonpolar Zn{sub 1-x}Mg{sub x}O epitaxial films on a-plane bulk ZnO by plasma-assisted molecular beam epitaxy

Nonpolar Zn{sub 1-x}Mg{sub x}O epitaxial films were grown by plasma-assisted molecular beam epitaxy on a-plane ZnO substrates. A smooth surface morphology was accomplished under oxygen-rich growth conditions. The benefits of the use of ZnO substrates on the structural properties are reflected by a low-density of threading dislocations. Furthermore, no indications for the generation of basal plane stacking faults are found. The pseudomorphic growth on a-plane ZnO substrates efficiently locks the epitaxial Zn{sub 1-x}Mg{sub x}O films to the wurtzite structure up to x = 0.25. The Mg concentration is not constant and increases with larger thickness. The optical properties reflect the influence of alloy disorder.

36 MATERIALS SCIENCE↗

Growth mechanism and microstructure of low defect density InN (0001) In-face thin films on Si (111) substrates

Transmission electron microscopy has been employed to analyze the direct nucleation and growth, by plasma-assisted molecular beam epitaxy, of high quality InN (0001) In-face thin films on (111) Si substrates. Critical steps of the heteroepitaxial growth process are InN nucleation at low substrate temperature under excessively high N-flux conditions and subsequent growth of the main InN epilayer at the optimum conditions, namely, substrate temperature 400–450 °C and In/N flux ratio close to 1. InN nucleation occurs in the form of a very high density of three dimensional (3D) islands, which coalesce very fast into a low surface roughness InN film. The reduced reactivity of Si at low temperature and its fast coverage by InN limit the amount of unintentional Si nitridation by the excessively high nitrogen flux and good bonding/adhesion of the InN film directly on the Si substrate is achieved. The subsequent overgrowth of the main InN epilayer, in a layer-by-layer growth mode that enhances the lateral growth of InN, reduces significantly the crystal mosaicity and the density of threading dislocations is about an order of magnitude less compared to InN films grown using an AlN/GaN intermediate nucleation/buffer layer on Si. The InN films exhibit the In-face polarity and very smooth atomically stepped surfaces.

36 MATERIALS SCIENCE↗

Terahertz electromodulation spectroscopy of electron transport in GaN

Time-resolved terahertz (THz) electromodulation spectroscopy is applied to investigate the high-frequency transport of electrons in gallium nitride at different doping concentrations and densities of threading dislocations. At THz frequencies, all structures reveal Drude transport. The analysis of the spectral response provides the fundamental transport properties, such as the electron scattering time and the electrons' conductivity effective mass. We observe the expected impact of ionized-impurity scattering and that scattering at threading dislocations only marginally affects the high-frequency mobility.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Semiconductor quantum dot lasers epitaxially grown on silicon with low linewidth enhancement factor

This work reports on the ultra-low linewidth enhancement factor (αH-factor) of semiconductor quantum dot lasers epitaxially grown on silicon. Owing to the low density of threading dislocations and resultant high gain, an αH value of 0.13 that is rather independent of the temperature range (288 K–308 K) is measured. Above the laser threshold, the linewidth enhancement factor does not increase extensively with the bias current which is very promising for the realization of future integrated circuits including high performance laser sources.

Duan, J. (ORCID:0000000177104287)↗

Atomic-scale analyses of Nb 3 Sn on Nb prepared by vapor diffusion for superconducting radiofrequency cavity applications: a correlative study

We report on atomic-scale analyses of the microstructure of an Nb 3 Sn coating on Nb, prepared by a vapor diffusion process for superconducting radiofrequency (SRF) cavity applications using transmission electron microscopy, electron backscatter diffraction and first-principles calculations. Epitaxial growth of Nb 3 Sn on a Nb substrate is found and four types of orientation relationships (ORs) at the Nb 3 Sn/Nb interface are identified by electron diffraction or high-resolution scanning transmission electron microscopy (HR-STEM) analyses. Thin Nb 3 Sn grains are observed in regions with a low Sn flux and they have a specific OR: Nb 3 Sn (1$\bar{2}$0) //Nb ($\bar{1}$11) and Nb 3 Sn (002) //Nb (0$\bar{1}$1) The Nb 3 Sn/Nb interface of thin grains has a large lattice mismatch, 12.3%, between Nb(0$\bar{1}$1) and Nb 3 Sn (002) and a high density of misfit dislocations as observed by HR-STEM. Based on our microstructural analyses of the thin grains, we conclude that the thin regions are probably a result of a slow interfacial migration with this particular OR. The Sn-deficient regions are seen to form initially at the Nb 3 Sn/Nb interface and remain in the grains due to the slow diffusion of Sn in bulk Nb 3 Sn. The formation of Sn-deficient regions and the effects of interfacial energies on the formation of Sn-deficient regions at different interfaces are estimated by first-principles calculations. The finding of ORs at the Nb 3 Sn/Nb interface provides important information about the formation of imperfections in Nb 3 Sn coatings, such as large thin-regions and Sn-deficient regions, which are critical to the performance of Nb 3 Sn SRF cavities for accelerators.

43 PARTICLE ACCELERATORS↗

Role of structural defects in mediating disordering processes at irradiated epitaxial Fe 3 O 4 / Cr 2 O 3 interfaces

Disordering processes in oxide materials are complicated by the presence of interfaces, which can serve as either point defect sinks or accumulation sites; the response depends on factors such as interfacial structure, chemistry, and termination. Here, we have characterized the disordering of epitaxial Fe 3 O 4 (111) / Cr 2 O 3 (0001) thin film heterostructures after 400 keV Ar 2+ radiation at room temperature. The density of misfit dislocations in both the Fe 3 O 4 overlayer and Cr 2 O 3 buffer layer is varied by changing the thickness of Cr 2 O 3 to be pseudomorphically strained to the Al 2 O 3 (0001) substrate (5 nm thick) or partially relaxed (20 nm thick), as confirmed by Bragg filtering analysis of scanning transmission electron microscopy images. In both cases, irradiation leads to damage accumulation on the Fe 3 O 4 side of the heterointerface, as shown by Rutherford backscattering spectrometry measurements in the channeling geometry. However, the interface with more misfit dislocations exhibits disordering at a faster rate than the less-defective interface. Likewise, layer-resolved electron energy loss spectroscopy reveals interfacial reduction of Fe after irradiation at the more defective interface. Intermixing of Cr across the interface is observed by atom probe tomography, which is likely facilitated by the generation of Cr interstitials in Cr 2 O 3 under irradiation.

36 MATERIALS SCIENCE↗