Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrode separator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Heterogeneous damage in Li-ion batteries: Experimental analysis and theoretical modeling

We assess the heterogeneous electrochemistry and mechanics in a composite electrode of commercial batteries using synchrotron X-ray tomography analysis and microstructure-resolved computational modeling. We visualize the morphological defects at multi-scales ranging from the macroscopic composite, particle ensembles, to individual single particles. Particle fracture and interfacial debonding are identified in a large set of tomographic data of active particles. Mechanical failure in the regime near the separator is more severe than toward the current collector. The active particles close to the separator experience deeper charge and discharge over cycles and thus are more mechanically loaded. The difference in the Li activity originates from the polarization of the electrolyte potential and the non-uniform distribution of the activation energy for the charge transfer reaction. We model the kinetics of intergranular fracture and interfacial degradation to confirm that the various Li activities are the major cause of the heterogeneous damage. The interfacial failure may reconstruct the conductive network and redistribute the electrochemical activities that render a dynamic nature of electrochemistry and mechanics evolving over time in the composite electrode. We further quantify the influence of the mechanical damage on the metrics of battery performance. We simulate the electrochemical impedance profile to build a relationship between the interfacial debonding and the impedance of electron transport and surface charge transfer. Lastly, the mechanical failure disrupts the conduction path of electrons and results in significant polarization and capacity loss in batteries.

25 ENERGY STORAGE↗

Highly Uniform Resistive Switching in HfO 2 Films Embedded with Ordered Metal Nanoisland Arrays

Memristors enter a critical developmental stage where emerging large-scale integration methods face major challenges with severe switching instabilities in the oxide layer. In this work, the superior uniformity is achieved within HfO 2 films by embedding highly ordered metal nanoisland (NI) arrays. Embedded films exhibit a significant reduction in both SET and RESET while displaying enhanced uniformity in operating voltages and resistance states. This behavior is attributed to the concentration of electric fields along Pt and Ti NIs and their interactions with the surrounding oxide film matrix environment, which induce separate and distinct filamentary formation mechanisms that affect the stability. A method is reported to further optimize the uniformity of the SET voltage by translating the NI array position down the film-thickness dimension towards the bottom electrode. A comparison of the density and distribution of the oxygen vacancies responsible for the formation/dissolution of conducting filaments is made via combined electrostatic force microscopy and conductive atomic force microscopy (c-AFM) studies. Finally, complete observation of the morphological evolution of conducting filaments produced by Pt and Ti is enabled by 3D c-AFM nanotomography and cross-sectional scanning transmission electron microscopy–energy dispersive spectroscopy to provide direct correlations between NI-oxide interactions and overall switching performance.

36 MATERIALS SCIENCE↗

Low-energy ion beam-based deposition of gallium nitride

An ion source with a remote plasma chamber excited by a 13.56 MHz radio frequency power was used for low-energy broad ion beam extraction. Optical emission spectral analyses showed the sputtering and postionization of a liquid gallium (Ga) target placed in a chamber separated from the source bombarded by argon (Ar) plasma guided by a bent magnetic field. In addition, an E × B probe successfully showed the extraction of low-energy Ga and Ar ion beams using a dual-electrode extractor configuration. By introducing dilute amounts of nitrogen gas into the system, formation of thin Ga-based films on a silicon substrate was demonstrated as determined from X-ray diffraction and X-ray reflectivity studies.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Evaluation of Electrochemical Nitrogen/hydrogen Gas Separator

An electrochemical nitrogen-hydrogen separator subsystem was investigated for use following catalytic dissociation of ammonia or hydrazine in a storage system being considered for long-duration manned space flight. An experimental cell with concentric tubular Pd-25Ag alloy hydrogen diffusion electrodes and hermetically sealed aqueous caustic electrolyte was developed.It was found that this cell operated satisfactorily at 210 C to 245 C and produced dry nitrogen and dry hydrogen with either or both gases at pressures up to 6.8 atmospheres (100 psia) or higher for storage. The final cell developed was operated satisfactorily for 176 days (4200 hours) with no evidence of deterioration of current-voltage performance. The best experimental performance was obtained at 245 C at currents up to 4 amperes (180 ma/sq cm and 360 ma/sq cm anode and cathode current densities, respectively) with a maximum steady-state cell voltage of 0.125 volt for an anode feed of pure hydrogen.

Clifford, J. E.↗

Dual Band Deep Ultraviolet AlGaN Photodetectors

We report on the design, fabrication and characterization of a back-illuminated voltage bias selectable dual-band AlGaN UV photodetector. The photodetector can separate UVA and W-B band radiation by bias switching a two terminal n-p-n homojunction structure that is fabricated in the same pixel. When a forward bias is applied between the top and bottom electrodes, the detector can sense UV-A and reject W-B band radiation. Alternatively, under reverse bias, the photodetector can sense UV-B and reject UV-A band radiation.

Aslam, S.↗

Method for recovering catalytic elements from fuel cell membrane electrode assemblies

A method for recovering catalytic elements from a fuel cell membrane electrode assembly is provided. The method includes converting the membrane electrode assembly into a particulate material, wetting the particulate material, forming a slurry comprising the wetted particulate material and an acid leachate adapted to dissolve at least one of the catalytic elements into a soluble catalytic element salt, separating the slurry into a depleted particulate material and a supernatant containing the catalytic element salt, and washing the depleted particulate material to remove any catalytic element salt retained within pores in the depleted particulate material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Unravelling Photocarrier Dynamics beyond the Space Charge Region for Photoelectrochemical Water Splitting

Semiconductor photoelectrodes for photoelectrochemical (PEC) water splitting require efficient carrier generation, separation, and transport at and beyond the space charge region (SCR) formed at the aqueous interface. The trade-off between photon collection and minority carrier delivery governs the photoelectrode design and implies maximum water splitting efficiency at an electrode thickness equivalent to the light absorption depth. Here, using planar ZnO thin films as a model system, we identify the photocarriers beyond the SCR as another significant source to substantially enhance the PEC performance. The high-quality ZnO films synthesized by pulsed laser deposition feature very few deep trap states and support a long photocarrier lifetime. Combined with photoelectrochemical characterization, ultrafast spectroscopy, and numerical calculations, it is revealed that engineering the exciton concentration gradient by film thickness facilitates the inward diffusion of photocarriers from the neighboring illuminated region to the SCR and, therefore, achieves a record high quantum efficiency over 80% at a thickness far beyond its light absorption depth and the SCR width. Furthermore, these results elucidate the important role of the photocarriers beyond SCR for the PEC process and provide new insight into exploring the full potential for efficient photoelectrode materials with large exciton diffusivity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Lithium Intercalation in Core-Shell Materials-Theoretical Analysis

Core-shell composite structures are potential candidates for Li-ion battery electrodes as they can take advantage of materials with higher energy density and materials with higher cyclability. This paper derives an analytical solution for isotropic 1-dimensional diffusion with galvanostatic boundary condition in composite slab, cylinder and sphere using separation of variables method. A general interfacial condition has been used to represent the dynamics at the interface of the composite material rendering the solution useful for wide variety of battery materials. Using the derived analytical solution for diffusion, intercalation induced stresses were estimated for spherical core-shell materials. (C) 2014 The Electrochemical Society. All rights reserved.

Suthar, B↗

Validation of Electrochemically Modulated Separations Performed On-Line with MC-ICP-MS for Uranium and Plutonium Isotopic Analyses

The most time consuming process in uranium or plutonium isotopic analyses is performing the requisite chromatographic separation of the actinides. Filament preparation for thermal ionization (TIMS) adds further delays, but is generally accepted due to the unmatched performance in trace isotopic analyses. Advances in Multi-Collector Inductively Coupled Plasma Mass Spectrometry (MC-ICP-MS) are beginning to rival the performance of TIMS. Methods, such as Electrochemically Modulated Separations (EMS) can efficiently pre-concentrate U or Pu quite selectively from small solution volumes in a matrix of 0.5 M nitric acid. When performed in-line with ICP-MS, the rapid analyte release from the electrode is fast, and large transient analyte signal enhancements of >100 fold can be achieved as compared to more conventional continuous nebulization of the original starting solution. This makes the approach ideal for very low level isotope ratio measurements. In this paper, some aspects of EMS performance are described. These include low level Pu isotope ratio behavior versus concentration by MC-ICP-MS and uranium rejection characteristics that are also important for reliable low level Pu isotope ratio determinations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ALD of Al2O3 for Highly Improved Performance in Li-Ion Batteries

Significant advances in energy density, rate capability and safety will be required for the implementation of Li-ion batteries in next generation electric vehicles. We have demonstrated atomic layer deposition (ALD) as a promising method to enable superior cycling performance for a vast variety of battery electrodes. The electrodes range from already demonstrated commercial technologies (cycled under extreme conditions) to new materials that could eventually lead to batteries with higher energy densities. For example, an Al2O3 ALD coating with a thickness of ~ 8 A was able to stabilize the cycling of unexplored MoO3 nanoparticle anodes with a high volume expansion. The ALD coating enabled stable cycling at C/2 with a capacity of ~ 900 mAh/g. Furthermore, rate capability studies showed the ALD-coated electrode maintained a capacity of 600 mAh/g at 5C. For uncoated electrodes it was only possible to observe stable cycling at C/10. Also, we recently reported that a thin ALD Al2O3 coating with a thickness of ~5 A can enable natural graphite (NG) electrodes to exhibit remarkably durable cycling at 50 degrees C. The ALD-coated NG electrodes displayed a 98% capacity retention after 200 charge-discharge cycles. In contrast, bare NG showed a rapid decay. Additionally, Al2O3 ALD films with a thickness of 2 to 4 A have been shown to allow LiCoO2 to exhibit 89% capacity retention after 120 charge-discharge cycles performed up to 4.5 V vs Li/Li+. Bare LiCoO2 rapidly deteriorated in the first few cycles. The capacity fade is likely caused by oxidative decomposition of the electrolyte at higher potentials or perhaps cobalt dissolution. Interestingly, we have recently fabricated full cells of NG and LiCoO2 where we coated both electrodes, one or the other electrode as well as neither electrode. In creating these full cells, we observed some surprising results that lead us to obtain a greater understanding of the ALD coatings. We have also recently coated a binder free LiNi0.04Mn0.04Co02O2 electrode containing 5 wt% single-walled carbon nanotubes as the conductive additive and demonstrated both high rate capability as well as the ability to cycle the cathode to 5 V vrs. Li/Li+. Finally, we coated a Celgard (TM) separator and enabled stable cycling in a high dielectric electrolyte. These results will be presented in detail.

25 ENERGY STORAGE↗

Dye Nanoaggregate Structures in MK-2, N3, and N749 Dye···TiO 2 Interfaces That Represent Dye-Sensitized Solar Cell Working Electrodes

The working electrode of a dye-sensitized solar cell (DSSC) consists of dye molecules adsorbed onto nanoparticles of a semiconductor such as TiO 2 . A reliable prediction of the DSSC photovoltaic performance of a given dye requires in-depth knowledge about the precise structure of the dye···TiO 2 interface. In this work, X-ray reflectometry (XRR) and grazing-incidence small-angle X-ray scattering (GISAXS) are employed to determine the dye···TiO 2 interfacial structure and associated dye aggregation behavior of three high-performance DSSC dyes, i.e., a metal-free organic dye, MK-2, and the two archetypal ruthenium-based organometallic dyes, N3 and N749 (Black Dye). Results show that all three dyes form nanoaggregates in dye···TiO 2 interfaces. We determine the dye nanoaggregate separations, sizes, distribution densities, and the extent of short-range order within each dye self-assembly in the longitudinal and lateral directions. Dye···TiO 2 composites fabricated using dye solutions of varying concentrations are analyzed. We find that nanoaggregates of the three dyes are separated by several hundred nanometers (158-203 nm) in dye···TiO 2 interfaces that have been fabricated using concentrated dye solutions (0.5 mM or 1.0 mM). MK-2 and N749 dyes also display smaller interparticle separations. Dye nanoparticle diameters are of the order of 156-198 nm, sizes that are comparable to the largest interparticle separations. Thus, no extraneous dye particles can be fitted into gaps between particles, so the dye self-assembly is saturated. Self-assemblies of all three dyes exhibit both lateral and longitudinal short-range order; N3 displays a particularly short coherence length along the TiO 2 surface, with extensive structured disorder along the longitudinal direction. The operation of DSSC working electrodes would therefore seem to be dependent on a dye self-assembly that may exhibit several levels of structural granularity and dye aggregation effects.

14 SOLAR ENERGY↗

Photoelectrochemical Properties and Stability of Nanoporous p-Type LaFeO 3 Photoelectrodes Prepared by Electrodeposition

LaFeO 3 is a p-type oxide that has an ideal bandgap and band edge positions for overall solar water splitting. This study reports an electrochemical synthesis method to produce LaFeO 3 as a high surface area, nanoporous photocathode. The resulting electrode generated a photocurrent density of 0.1 mA/cm 2 at a potential as positive as 0.73 V vs. RHE for photoelectrochemical oxygen reduction with a photocurrent onset potential very close to its flatband potential of 1.45 V vs. RHE. Furthermore, without a protection layer it showed a stable photocurrent generation with no sign of photocorrosion. Due to the poor catalytic nature of the LaFeO 3 surface for water reduction, photocurrent obtained for water reduction was not substantial. Furthermore, its photostability and its ability to achieve a photovoltage for water reduction greater than 1.2 V encourage further studies on doping to enhance electron-hole separation as well as interfacing appropriate hydrogen evolution catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multiplexed Anodic Stripping Voltammetry Detection of Heavy Metals in Water Using Nanocomposites Modified Screen-Printed Electrodes Integrated With a 3D-Printed Flow Cell

In this study, we present multiplexed anodic stripping voltammetry (ASV) detection of heavy metal ions (HMIs)—As(III), Cd(II), and Pb(II)—using a homemade electrochemical cell consisting of dual working, reference and counter screen-printed electrodes (SPE) on polyimide substrate integrated with a 3D-printed flow cell. Working and counter electrodes were fabricated by the screen-printing of graphite paste while the Ag/AgCl paste was screen-printed as a reference electrode (Ag/AgCl quasi-reference electrode). The working electrodes were modified with (BiO) 2 CO 3 -reduced graphene oxide (rGO)-Nafion [(BiO) 2 CO 3 -rGO-Nafion] and Fe 3 O 4 magnetic nanoparticles (Fe 3 O 4 MNPs) decorated Au nanoparticles (AuNPs)-ionic liquid (IL) (Fe 3 O 4 -Au-IL) nanocomposites separately to enhance HMIs sensing. Electrochemical detection was achieved using square wave ASV technique. The desired structure of the flow electrochemical cell was optimized by the computational fluid dynamic (CFD). Different experimental parameters for stripping analysis of HMIs were optimized including deposition time, deposition potential and flow rate. The linear range of calibration curves with the sensing nanocomposites modified SPE for the three metal ions was from 0–50 μg/L. The limits of detection (S/N = 3) were estimated to be 2.4 μg/L for As(III), 1.2 μg/L for Pb(II) and 0.8 μg/L for Cd(II). Furthermore, the homemade flow anodic stripping sensor platform was used to detect HMIs in simulated river water with a 95–101% recovery, indicating high selectivity and accuracy and great potential for applicability even in complex matrices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Spatial separation and motion of electric charges arising due to the interaction of high-power IR laser radiation with water

We have studied temporal and amplitude characteristics of the electrical signal arising under irradiation of the free water surface by a 2.94-{mu}m high-power laser. The investigations have been conducted using a specially designed electrode system, which makes it possible to record the motion of the electric charge after the end of the laser pulse. We have measured the dependences of the signal parameters on the radiation energy density at the water surface. (interaction of laser radiation with matter)

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Numerical Simulations of Flow Separation Control in Low-Pressure Turbines using Plasma Actuators

A recently introduced phenomenological model to simulate flow control applications using plasma actuators has been further developed and improved in order to expand its use to complicated actuator geometries. The new modeling approach eliminates the requirement of an empirical charge density distribution shape by using the embedded electrode as a source for the charge density. The resulting model is validated against a flat plate experiment with quiescent environment. The modeling approach incorporates the effect of the plasma actuators on the external flow into Navier Stokes computations as a body force vector which is obtained as a product of the net charge density and the electric field. The model solves the Maxwell equation to obtain the electric field due to the applied AC voltage at the electrodes and an additional equation for the charge density distribution representing the plasma density. The new modeling approach solves the charge density equation in the computational domain assuming the embedded electrode as a source therefore automatically generating a charge density distribution on the surface exposed to the flow similar to that observed in the experiments without explicitly specifying an empirical distribution. The model is validated against a flat plate experiment with quiescent environment.

Suzen, Y. B.↗

Correlations between Transition Metal Chemistry, Local Structure and Global Structure in Li 2 Ru 0.5 Mn 0.5 O 3 Investigated in a Wide Voltage Window

Li 2 Ru 0.5 Mn 0.5 O 3 , a high capacity lithium rich layered cathode material for lithium-ion batteries, was subject to comprehen-sive diagnostic studies including in situ/ex situ X-ray diffraction (XRD), X-ray absorption spectroscopy (XAS), pair distribu-tion function (PDF) and high resolution scanning transmission electron microscopy (STEM) analysis, to understand the cor-relations between transition metal chemistry, structure and lithium storage electrochemical behavior. Ru-Ru dimers have been identified in the as-prepared sample and found to be preserved upon prolonged cycling. Presence of these dimers, which are likely caused by the delocalized nature of 4d electrons, is found to favor the stabilization of the structure in a lay-ered phase. The in situ XAS results confirm the participation of oxygen redox into the charge compensation at high charge voltage, and the great flexibility of the covalent bond between Ru and O may provide great reversibility of the global struc-ture despite of the significant local distortion around Ru. In contrast, the local distortion around Mn occurs at low discharge voltage and is accompanied by a “layered to 1T” phase transformation, which is found to be detrimental to the cycle per-formances. It is clear that the changes of local structure around individual transition metal cations respond separately and differently to lithium intercalation/deintercalation. Here, cations with the capability to tolerate the lattice distortion will benefit for maintaining the integrality of the crystal structure and therefore is able to enhance the long-term cycling performance of the electrode materials.

25 ENERGY STORAGE↗