Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Interfacial Void Formation and Self-Healing in Oxide Scales on Al-containing High-Entropy Alloy

The exceptional high-temperature oxidation resistance of Al-containing high-entropy alloys (HEAs) is often attributed to the formation of a protective α-Al 2 O 3 scale. However, the dynamic, atomic-scale mechanisms governing the stability of this scale—including interfacial void formation and the often-postulated but rarely visualized “self-healing” capacity—remain poorly understood. Herein, we reveal the complex evolution of the triple-layer oxide scale on an Al 10 CoCrFeNi HEA through combined electron microscopy and diffraction study. We show that interfacial voids are an inherent consequence of the scaling process, originating from two distinct mechanisms: the Kirkendall effect at the interface between the γ-Al 2 O 3 /α-Al 2 O 3 and alloy driven by cationic diffusion imbalance and volumetric contraction due to phase transformations at the spinel/Cr 2 O 3 interface. Crucially, we provide microstructural evidence consistent with an intrinsic self-healing response. This process is driven by coupled inward diffusion of oxygen and outward diffusion of metal cations, leading to the in-situ formation of transient θ-Al 2 O 3 and spinel phases that partially fill and seal the voids. Here, these results provide atomic-scale insights into the phase evolution, defect formation, and self-repair of oxide scales in HEAs—highlighting pathways to enhance their oxidation resistance in extreme environments.

High-entropy alloy↗

X ray photoelectron analysis of oxide-semiconductor interface after breakdown in Al{sub 2}O{sub 3}/InGaAs stacks

In this work, the post-breakdown characteristics of metal gate/Al{sub 2}O{sub 3}/InGaAs structures were studied using surface analysis by x ray photoelectron spectroscopy. The results show that for dielectric breakdown under positive bias, localized filaments consisting of oxidized substrate atoms (In, Ga and As) were formed, while following breakdown under negative bias, a decrease of oxidized substrate atoms was observed. Such differences in the microstructure at the oxide-semiconductor interface after breakdown for positive and negative voltages are explained by atomic diffusion of the contact atoms into the gate dielectric in the region of the breakdown spot by the current induced electro-migration effect. These findings show a major difference between Al{sub 2}O{sub 3}/InGaAs and SiO{sub 2}/Si interfaces, opening the way to a better understanding of the breakdown characteristics of III-V complementary-metal-oxide-semiconductor technology.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Gravity Level on the Particle Shape and Size During Zeolite Crystal Growth

A microscopic diffusion model is developed to represent solute transport in the boundary layer of a growing zeolite crystal. This model is used to describe the effect of gravity on particle shape and solute distribution. Particle dynamics and crystal growth kinetics serve as the boundary conditions of flow and convection-diffusion equations. A statistical rate theory is used to obtain the rate of solute transport across the growing interface, which is expressed in terms of concentration and velocity of solute species. Microgravity can significantly decrease the solute velocity across the growing interface compared to its earth-based counterpart. The extent of this reduction highly depends on solute diffusion constant in solution. Under gravity, the flow towards the crystal enhances solute transport rate across the growing interface while the flow away from crystals reduces this rate, suggesting a non-uniform growth rate and thus an elliptic final shape. However, microgravity can significantly reduce the influence of flow and obtain a final product with perfect spherical shape. The model predictions compare favorably with the data of space experiment of zeolites grown in space.

Song, Hong-Wei↗

In Situ Observation of Growth Dynamics in DECLIC Directional Solidification Insert Onboard ISS: DSI-R Flight Campaign

The study of solidification microstructure formation is of utmost importance for materials design and processing, as solid-liquid interface patterns largely govern mechanical and physical properties. Pattern selection occurs under dynamic conditions of growth in which the initial morphological instability evolves nonlinearly and undergoes a reorganization process. The dynamic and nonlinear nature of this instability renders in situ observation of the interface an invaluable tool to gain knowledge on the time-evolution of the interface pattern. Transparent organic analogs, which solidify like metallic alloys, allow direct visualization of interface dynamics. Extensive ground-based studies of both metallic and organic bulk samples have established the presence of significant convection during solidification processes that alters the formation of interfacial microstructures. A reduced-gravity environment is therefore mandatory for fluid flow elimination in bulk samples. In the framework of the CNES project MISOL3D (MIcrostrutures de SOLidification 3D) and the NASA projects DSIP (Dynamical Selection of 3D Interface Patterns), SPADES (SPAtiotemporal Evolution of three-dimensional DEndritic array Structures) and CAMUS (ComputAtional Studies of MicrostrUcture Formation During Alloy Solidification in Microgravity), we participated in the development of the Directional Solidification Insert (DSI) of the DEvice for the study of Critical Liquids and Crystallization (DECLIC). The DECLIC-DSI is dedicated to in situ and real-time characterization of solid-liquid interface patterns during directional solidification of transparent alloys in diffusive transport regime. Between April 2010 and March 2011, the first ISS campaign (DSI) explored the entire range of microstructures resulting in unprecedented observations. A second campaign (DSI-R), performed between October 2017 and December 2018, in which the insert contained an alloy of higher solute concentration, allowed to complete the benchmark database. The increase of solute concentration resulted in well-developed dendritic patterns at lower velocities (lower interface curvature and larger tip radius). The microstructure resulting from dendritic growth is dominant in metallurgy so that it is fundamental to understand the mechanisms of its formation. The main aims of this experimental campaign are to understand: the mechanisms of the cell to dendrite transition, the fundamental mechanisms of sidebranching formation, the dependence of dendrite tip shapes on growth conditions, the interaction of primary array and secondary sidebranches, and the influence of subgrain boundaries on the spatiotemporal organization of the array structure. Preparation, analysis and interpretation of the experiments performed onboard ISS are considerably enhanced by experiments performed on ground using thin-samples (Pr. Trivedi’s group) and phase-field simulations of microstructure formation in a diffuse growth regime (Pr. Karma’s group). In this summary, we will present an initial assessment of the results obtained during the DSI-R campaign. Nomenclature Vp: pulling velocity G: thermal gradient L: solidified length rtip: tip curvature radius Acronyms/Abbreviations CADMOS: Centre d'Aide au Développement des activités en Micro-pesanteur et des Opérations Spatiales CNES: Centre National d’Études Spatiales DECLIC: Device for the study of Critical LIquids and Crystallization DSI: Directional Solidification Insert DSI-R: Directional Solidification Insert - Refurbish ISS: International Space Station NASA: National Aeronautics and Space Administration PF: phase-field SCN: Succinonitrile 3D: three-dimensional

Mota, F.L.↗

Kinetic Monte Carlo Simulations of Oxygen Diffusion in Environmental Barrier Coating Materials

Ceramic Matrix Composite (CMC) materials are of interest for use in next-generation turbine engine components, offering a number of significant advantages, including reduced weight and high operating temperatures. However, in the hot environment in which such components operate, the presence of water vapor can lead to corrosion and recession, limiting the useful life of the components. Such degradation can be reduced through the use of Environmental Barrier Coatings (EBCs) that limit the amount of oxygen and water vapor reaching the component. Candidate EBC materials include Yttrium and Ytterbium silicates. In this work we present results of kinetic Monte Carlo (kMC) simulations of oxygen diffusion, via the vacancy mechanism, in Yttrium and Ytterbium disilicates, along with a brief discussion of interstitial diffusion. An EBC system typically includes a bond coat located between the EBC and the component surface. Bond coat materials are generally chosen for properties other than low oxygen diffusivity, but low oxygen diffusivity is nevertheless a desirable characteristic, as the bond coat could provide some additional component protection, particularly in the case where cracks in the coating system provide a direct path from the environment to the bond coat interface. We have therefore performed similar kMC simulations of oxygen diffusion in this material.

Good, Brian S.↗

Diffusional decay of striations

This paper investigates the amount of decay of growth striations in bulk crystals grown from melts and solutions, due to solid-state diffusion during the cooling of the crystal to room temperature. A model is developed based on the assumption of a sinusoidal variation in the solid composition at the interface of a semiinfinite ingot growing at constant velocity, and the damping behavior of this variation is followed as it moves away from the solid-liquid interface. Numerical results are presented showing that an increase in the diffusivity causes the striations to penetrate deeper into the solid and, consequently causes the distance for 99.9 percent decay to increase. Analytical results are also presented for the decay of striations in an isothermal ingot induced by a sinusoidal fluctuation in the rate of crystal growth.

Gray, R. T.↗

Analytical modeling for redox flow battery design

Deeper market penetration of redox flow batteries requires optimization of the cell performance. Though important for optimization, detailed analytical solutions have not been developed for electrolyte flow, mass and charge transport, and reaction kinetics within redox flow batteries. To this end, here we present analytical solutions to active species concentration and over-potential based on advection-diffusion transport for ions and Bulter-Volmer model for interface reaction kinetics. The solutions were validated with results from a finite element model. These solutions were then applied to investigate the relationship between over-potential and state of charge, current density, reaction rate constant, flow velocity, diffusivity, total active species concentration, and electrode structure. Explicit formulas were identified for minimum activation over-potential and limiting current density as well as their dependence on electrolyte properties, operation conditions, and electrode structure. With our new mathematical formulas, this work provides a theoretical framework for flow battery design.

25 ENERGY STORAGE↗

Bio-Oil Impact on Water Diffusion and Durability of Bitumen: Influence of Aging and Salinity

Bio-oils derived from inexpensive biomass offer environmentally friendly options for modifying bitumen for improved durability or rejuvenating aged material, although their impact on bitumen moisture resistance can be mixed. A better understanding of water diffusion into bitumen and its interactions with bio-oil compounds would aid the development of effective bio-oils. In this study, the effect of water exposure on bio-oil-modified bitumen blends was examined by de-wetting contact angle measurements and differential FTIR spectroscopy. The bio-oils improved the anti-stripping behavior of the bitumen but also increased water absorption which could weaken cohesive strength. Short-term thermal aging increased water diffusion for all bitumen blends including the control, probably due to the presence of more oxidized compounds. Negative peaks of alkanes and polar groups in the differential FTIR data suggest the co-diffusion of surfactant molecules towards the bitumen-water interface. Basic pH increased de-wetting of some bitumen blends from silica, possibly by attacking the silica surface itself. The presence of salt in solution altered the bitumen surface composition through the formation of salt complexes with bitumen or bio-oil compounds. In particular, the formation of calcium-carboxylate complexes appeared to greatly improve anti-stripping effects of bio-oils. Water diffusion into most of the bitumen blends was insensitive to pH or salt concentration except for a few notable outliers. Identifying the compounds responsible for increasing or decreasing water diffusion in these outlier cases would be valuable developing future bio-oil formations that avoid or promote those compounds.

Hung, Albert M.↗

A Stable and Conservative Interface Treatment of Arbitrary Spatial Accuracy

Stable and accurate interface conditions are derived for the linear advection-diffusion equation. The conditions are functionally independent of the spatial order of accuracy and rely only on the form of the discrete operator. We focus on high-order finite-difference operators that satisfy the summation-by-parts (SBP) property. We prove that stability is a natural consequence of the SBP operators used in conjunction with the new boundary conditions. In addition, we show that the interface treatments are conservative. New finite-difference operators of spatial accuracy up to sixth order are constructed: these operators satisfy the SBP property. Finite-difference operators are shown to admit design accuracy (p(sup th)-order global accuracy) when (p - 1)(sup th)-order stencil closures are used near the boundaries if the physical boundary conditions are implemented to at least p(sup th)-order accuracy. Stability and accuracy are demonstrated on the nonlinear Burgers' equation for an twelve-subdomain problem with randomly distributed interfaces.

Carpenter, Mark H.↗

Temperature dependent spin transport properties of platinum inferred from spin Hall magnetoresistance measurements

We study the temperature dependence of the spin Hall magnetoresistance (SMR) in yttrium iron garnet/platinum hybrid structures via magnetization orientation dependent magnetoresistance measurements. Our experiments show a decrease of the SMR magnitude with decreasing temperature. Using the sensitivity of the SMR to the spin transport properties of the normal metal, we interpret our data in terms of a decrease of the spin Hall angle in platinum from 0.11 at room temperature to 0.075 at 10 K, while the spin diffusion length and the spin mixing conductance of the ferrimagnetic insulator/normal metal interface remain almost constant.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Correlation between Interface Microstructure and Bond Strength of Al6061/Al6061 HIP-Bonded Plates for Fuel Cladding Application

The effects of hot isostatic pressing (HIP) processing parameters on microstructure and bond strength of Al6061/Al6061 plate interfaces were systemically investigated at the micro- and nanoscale. The HIP bonding of the two aluminum plates was performed at four temperatures: 350°C, 400°C, 450°C, and 560°C. The results reveal the formation of micron scaled Mg 2 Si precipitate and uniform nano scaled Mg 2 Al 2 O 5 oxide at the interface. The formation of Mg 2 Al 2 O 5 is closely associated with the fast bulk diffusion of Mg from the Al matrix to the amorphous Al 2 O 3 /Al interface and subsequent reaction between Mg and Al 2 O 3 . Finally, the highest and lowest bond strengths were observed in samples HIP bonded at 450°C and 350°C, respectively.

36 MATERIALS SCIENCE↗

Derivation of a continuum model and the energy law for moving contact lines with insoluble surfactants

A continuous model is derived for the dynamics of two immiscible fluids with moving contact lines and insoluble surfactants based on thermodynamic principles. The continuum model consists of the Navier-Stokes equations for the dynamics of the two fluids and a convection-diffusion equation for the evolution of the surfactant on the fluid interface. The interface condition, the boundary condition for the slip velocity, and the condition for the dynamic contact angle are derived from the consideration of energy dissipations. Different types of energy dissipations, including the viscous dissipation, the dissipations on the solid wall and at the contact line, as well as the dissipation due to the diffusion of surfactant, are identified from the analysis. A finite element method is developed for the continuum model. Numerical experiments are performed to demonstrate the influence of surfactant on the contact line dynamics. The different types of energy dissipations are compared numerically.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Adapting confocal Raman microscopy for in situ studies of redox transformations at electrode-electrolyte interfaces

Confocal Raman microscopy was applied to quantify redox species present within the diffusion layer adjacent to an electrode surface under potentiostatic control. A glass microscope coverslip with a thin indium tin oxide (ITO) coating served as both the working electrode and optical window for a microscope-stage mountable spectroelectrochemical cell. A high numerical aperture objective mounted in an inverted microscope frame just below the stage brought excitation radiation through the coverslip window and to a tight focus a few micrometers above the ITO film surface. Species diffusing into the confocal probe volume defined by the excitation beam focus and the collected light region were detected, identified and quantified based on their Raman scattering frequencies and intensities. Here, in measurements that interrogated the interconversion of ferrocyanide and ferricyanide ions as a function of applied voltage, least-squares regression analysis of spectral datasets predicted the formal potential and relative surface concentrations of the ions in good agreement with the expected Nernstian response. Preliminary studies of methyl viologen reduction at an ITO film/Nafion membrane interface were conducted and show the possibility for estimation of mass transport coefficients of redox species within ionic polymer materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Polymer Solar Cells with 18.74% Efficiency: From Bulk Heterojunction to Interdigitated Bulk Heterojunction

The most popular approach to fabricating organic solar cells (OSCs) is solution processing a mixture of donor (D) and acceptor (A) materials into an active layer with a bulk heterojunction (BHJ) nanostructure. In this work, it is demonstrated that the interdigitated heterojunction (IHJ) is a more suitable nanostructure of the active layer for high-performance OSCs whereas it is a long standing challenge to realize well-defined IHJ structures. Here, a facile and versatile sequential solution processing method is developed to produce an IHJ nanostructure with power conversion efficiency reaching 18.74% (18.10% for BHJ the counterpart) by fabricating a donor film with nanopores created by a wax additive, sequentially casting the acceptor on top of infiltrating the nanopores. Compared to the BHJ, the IHJ structure with an interpillar distance within the exciton diffusion length can afford a large bulk D/A interface for efficient exciton dissociation with a minimized charge recombination while free electrons and holes can transport to the respective electrodes through more straightforward pathways, thus enhance performance. Furthermore, the D or A phase in the IHJ device contacts with only one electrode, which can prevent shunting between the anode and cathode and facilitate the industrial mass production of OSCs.

36 MATERIALS SCIENCE↗

Electrochemical Behavior of Sn-9Zn-xTi Lead-Free Solders in Neutral 0.5M NaCl Solution

Electrochemical techniques were employed to study the electrochemical corrosion behavior of Sn-9Zn-xTi (x = 0, 0.05, 0.1, 0.2 wt.%) lead-free solders in neutral 0.5M NaCl solution, aiming to figure out the effect of Ti content on the corrosion properties of Sn-9Zn, providing information for the composition design of Sn-Zn-based lead-free solders from the perspective of corrosion. EIS results reveal that Ti addition was involved in the corrosion product layer and changed electrochemical interface behavior from charge transfer control process to diffusion control process. The trace amount of Ti addition (0.05 wt.%) can refine the microstructure and improve the corrosion resistance of Sn-9Zn solder, evidenced by much lower corrosion current density (i{sub corr}) and much higher total resistance (R{sub t}). Excess Ti addition (over 0.1 wt.%) led to the formation of Ti-containing IMCs, which were confirmed as Sn{sub 3}Ti{sub 2} and Sn{sub 5}Ti{sub 6}, deteriorating the corrosion resistance of Sn-9Zn-xTi solders. The main corrosion products were confirmed as Sn{sub 3}O(OH){sub 2}Cl{sub 2} mixed with small amount of chlorine/oxide Sn compounds.

36 MATERIALS SCIENCE↗

Effect of an in-situ thermal annealing on the structural properties of self-assembled GaSb/GaAs quantum dots

The effect of the application of a thermal annealing on the structural properties of GaSb/GaAs quantum dots (QDs) is analyzed by aberration corrected high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and electron energy loss spectroscopy (EELS). Our results show that the GaSb/GaAs QDs are more elongated after the annealing, and that the interfaces are less abrupt due to the Sb diffusion. We have also found a strong reduction in the misfit dislocation density with the annealing. The analysis by EELS of a threading dislocation has shown that the dislocation core is rich in Sb. In addition, the region of the GaAs substrate delimited by the threading dislocation is shown to be Sb-rich as well. An enhanced diffusion of Sb due to a mechanism assisted by the dislocation movement is discussed.

36 MATERIALS SCIENCE↗

The role of Si in determining the stability of the θ; precipitate in Al-Cu-Mn-Zr alloys

Precipitate-strengthened Al-Cu-Mn-Zr (ACMZ) alloys demonstrate improved microstructural stability compared to conventional Al-Cu alloys. Si is typically considered an impurity in these alloys, but a systematic analysis of ACMZ alloys with a range of Si levels revealed that there is a Si content range (~0.05 wt. % < Si < ~0.10 wt. %) for achieving optimal high temperature microstructural stability. A combination of hardness testing, scanning electron microscopy, and atom probe tomography has been used to understand the relationship between Si content, aging response, and thermal stability in ACMZ alloys. It is shown that the optimum Si content range corresponds to a reduced as-aged hardness, but a greater hardness value retained by the alloy after thermal exposure to 350 °C for 200 hours. A mechanism is proposed in which optimum Si levels reduce the number density of nucleation sites for θ' precipitates, resulting in larger precipitates that, on average, provide a reduced as-aged strength but are more coarsening resistant. This inherent θ' coarsening resistance allows more time for slow-diffusing Mn and Zr to reach the θ' interface and further stabilize the precipitates. Designing the optimal as-aged microstructure for improved thermal stability of the alloy by controlling impurity levels is a concept that has implications beyond the investigated Al-Cu alloy system.

36 MATERIALS SCIENCE↗