Study of Material Consolidation at Higher Throughput Parameters in Selective Laser Melting of Inconel 718
No abstract available
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
No abstract available
Results of characterization of Dielectric Barrier Discharge (DBD) plasma actuators without external flow are presented. The results include aerodynamic and electric performance of the actuators without external flow for different geometrical parameters, dielectric materials and applied voltage level and wave form.
Tip clearance within the high pressure turbine of a gas turbine engine is a significant factor in engine performance and efficiency. In the pursuit of higher efficiency, aero-engine designs are migrating toward compact gas turbine (CGT) technology that seeks to increase the bypass ratio of the gas turbine engine without increasing the size of the fan, which is constrained by its underwing location. The reduced size of CGTs invoke concern over increased sensitivity of engine performance due to turbine tip clearance gap that makes an argument for advanced tip clearance mitigation and control techniques to be employed. This paper evaluates the tip clearance trade space for a conceptual geared turbofan engine with a CGT core. This is accomplished through a modeling and simulation approach that includes a sensitivity analysis of engine performance in response to high pressure turbine tip clearance as well as an evaluation of the sensitivity of tip clearance to various design parameters, including material properties and component cooling characteristics. Also included is a parametric study of actuators that provides preliminary requirements for implementation of active turbine tip clearance control actuation systems. The results produced from these studies are meant to be informative, with special emphasis on the demonstration of a systematic approach. The modeling approach appears to capture expected trends. The studies suggest that the tip clearance gap will have a greater impact on the new CGT engines and that a relatively slow, actively controlled actuation system may be sufficient as long as it has control authority to both open and close the tip clearance gap.
By increasing the quantum well barrier width, incorporating spacer layers between the contacts and the multi quantum well region, and optimizing the materials growth parameters, we have dramatically reduced the dark current by many orders of magnitude and thereby significantly increased the detectivity.
Metal additive manufacturing (AM) is a generic term that captures a variety of fabrication techniques. Each of these manufacturing process has unique advantages, applications for use, and challenges. The most common AM processes in use include Powder Bed Fusion (PBF) and Directed Energy Deposition (DED) as well as many solid state processes. While detailed research has been conducted among many of the processes including parameters and material properties, navigating which processes are best to select is difficult as it is based on component requirements. The focus of this presentation is to provide an overview of considerations for each of metal AM process selection for aerospace components based on various attributes. These attributes include geometric considerations, metallurgical characteristics, cost basis, post-processing and maturity of the processes. The data for these trade selections are based on studies that NASA as performed internally and with academic and industry partners. These studies include multiple AM build experiments to evaluate (1) geometric variations and constraints within the processes, (2) alloy characterization and mechanical testing, (3) pathfinder component development and hotfire evaluations, and (4) certification approaches. This presentation summarizes these results and meant to introduce various considerations when designing a metal AM component.
In recent years, Austin, Texas has experienced an increase in population and urban development. Additionally, the City’s climate—already characterized by periods of extreme heat and drought—continues to change. As temperatures and demand for utilities and cooling resources rise, the number of heat-related deaths and illnesses in socially vulnerable populations (e.g., older, lower-income populations) is expected to increase. The City of Austin, The University of Texas at Austin (UT Austin), and The University of Texas Health Science Center at Houston (UT Health) partnered with NASA DEVELOP to examine the distribution of urban heat throughout the City. This project used land surface temperature, greenness, plant water content, and urban surface material analysis parameters derived from NASA Earth observations from Landsat 8 Operational Land Imager (OLI), Landsat 8 Thermal Infrared Sensor (TIRS), and Aqua and Terra Moderate Resolution Imaging Spectroradiometer (MODIS). The project team produced three different indices to create a spatial analysis for the study area including a social vulnerability index (SoVI), heat exposure index (HEI), and an overall heat priority index (HPI) score. This overall score was determined with a weighted analysis of heat-related environmental variables from NASA Earth observations and socioeconomic data from the 2019 American Community Survey. Based on the HPI score, the project team identified 121 census block groups out of 605 total that are designated as being most at risk of adverse impacts from extreme heat events. To test the sensitivity of the HPI, the team used a Monte Carlo analysis using different approaches for geographic scale, variable inclusion, census uncertainty, and index aggregation. Based on the sensitivity analysis, the resulting HPI score showed the metric was consistent with the baseline HPI. This provided increased confidence the score can be used as a tool to make informed infrastructure improvement plans in targeted areas (e.g., siting of cooling centers) and ensure equitable sustainable development.
Metal additive manufacturing (AM) is a generic term that captures a variety of fabrication processes. Each of these manufacturing process has unique advantages and challenges for use in aerospace propulsion applications. The most commonly used AM processes include Powder Bed Fusion (PBF), Directed Energy Deposition (DED), and solid-state processes as in Cold Spray, Ultrasonic Additive Manufacturing, and Additive Friction Stir Deposition. While detailed research has been conducted among many of the AM processes to mature processing parameters and material properties, navigating which processes are best to select is difficult as it is based on specific component requirements. The focus of this presentation is to provide an overview of considerations for each of metal AM process selection for aerospace components based on various key attributes. These key attributes include geometric considerations, metallurgical characteristics, cost basis, post-processing and maturity of the processes. The data for these trade selections are based on studies that NASA as performed internally and with academic and industry partners. These studies include multiple AM build experiments to evaluate (1) geometric variations and constraints within the processes, (2) alloy characterization and mechanical testing, (3) pathfinder component development and hot-fire evaluations, and (4) certification approaches. This presentation summarizes these results and is meant to introduce specific examples which show what to consider when designing a metal AM component for aerospace propulsion applications.
Metal additive manufacturing (AM) is a generic term that captures a variety of fabrication processes. Each of these manufacturing process has unique advantages and challenges for use in aerospace propulsion applications. The most commonly used AM processes include Powder Bed Fusion (PBF), Directed Energy Deposition (DED), and solid-state processes as in Cold Spray, Ultrasonic Additive Manufacturing, and Additive Friction Stir Deposition. While detailed research has been conducted among many of the AM processes to mature processing parameters and material properties, navigating which processes are best to select is difficult as it is based on specific component requirements. The focus of this presentation is to provide an overview of considerations for each of metal AM process selection for aerospace components based on various key attributes. These key attributes include geometric considerations, metallurgical characteristics, cost basis, post-processing and maturity of the processes. The data for these trade selections are based on studies that NASA as performed internally and with academic and industry partners. These studies include multiple AM build experiments to evaluate (1) geometric variations and constraints within the processes, (2) alloy characterization and mechanical testing, (3) pathfinder component development and hot-fire evaluations, and (4) certification approaches. This presentation summarizes these results and is meant to introduce specific examples which show what to consider when designing a metal AM component for aerospace propulsion applications.
Space Flight Hardware (SFH) experiences intense vibratory loading during flight, which only lasts a few minutes. When determining the appropriate size of these components to withstand such loading without becoming damaged (plastically deforming or breaking), standard design practice is to assume that the peak dynamic loads are applied statically. In doing so, the resulting stress is compared against a material strength parameter obtained from a quasi-static experiment. Since the near-peak stresses are only experienced over a small fraction of time in reality, this approach leads to design conservatism that unnecessarily increases structural mass as well as the associated inefficiency and financial cost. In an effort to modernize engineering design standards to appropriately consider the higher practical strength of dynamically loaded structures, this overarching research project seeks to develop an experimental test procedure for quantifying the dynamic strength of metallic alloys as a function of excitation frequency. In the ideal case, the characterization test would include an in-situ method for monitoring the onset and progression of plastic deformation of the test specimen undergoing vibratory loading. These new tests are designed to be high intensity (forcing amplitude), short term (60 seconds at full amplitude), and cyclic in nature (sinusoidal excitation via attached stinger to an otherwise cantilevered beam). In addition, the initial metallic alloy under investigation is 6061 aluminum, due to its wide use and applicability for SFH. Thus far, the most promising monitoring method under development with live-capacity is to track hysteresis behavior of the beam from power dissipation trends, calculated via force (from transducer on excitation stinger) and velocity (measurements from Laser Doppler Vibrometer) data and work to distinguish between elastic and plastic features. As a key component of this ongoing method development, any pseudo-live indication of plasticity can be corroborated against the outcome of a pre-post assessment of damage via macroscopic evaluation of beam geometry (i.e. assessing any permanent change in the beam’s tip deflection). Support for experimental design decisions as well as dynamic strength data from tests with excitation frequencies of 10, 40, and 55 Hz will be discussed. This work contributes to the foundation for a new type of vibration-based characterization experiments and generates initial data on the functional strength of 6061 aluminum under the conditions considered. Keywords: vibrations, plastic deformation, aluminum
Space Flight Hardware (SFH) experiences intense vibratory loading during flight, which only lasts a few minutes. When determining the appropriate size of these components to withstand such loading without becoming damaged, standard design practice is to assume that the peak dynamic loads are applied statically. In doing so, the resulting stress is compared against a material strength parameter obtained from a quasi-static experiment. Since the near-peak stresses are only experienced over a small fraction of time in reality, this approach leads to design conservatism that unnecessarily increases structural mass as well as the associated inefficiency and financial cost. In an effort to modernize engineering design standards to appropriately consider the higher practical strength of dynamically loaded structures, this overarching research project seeks to develop an experimental test procedure for quantifying the dynamic strength of metallic alloys as a function of excitation frequency. In the ideal case, the characterization test would include an in-situ method for monitoring the onset and progression of plastic deformation of the test specimen undergoing vibratory loading. These new tests are designed to be high intensity (forcing amplitude), short term (60 seconds at full amplitude), and cyclic in nature (sinusoidal excitation via attached stinger to an otherwise cantilevered beam). In addition, the initial alloy under investigation is 6061 aluminum, due to its wide use and applicability for SFH. Thus far, the primary candidate under development with live-capacity is to track hysteresis behavior of the beam from power dissipation trends, calculated via force (from transducer on excitation stinger) and velocity (measurements from Laser Doppler Vibrometer) data and work to distinguish between elastic and plastic features. As a key component of this ongoing method development, any pseudo-live indication of plasticity could be corroborated against the outcome of a pre-post assessment of damage via macroscopic evaluation of beam geometry (i.e. assessing any permanent change in the beam’s tip deflection). Support for experimental design decisions as well as dynamic strength data from tests with excitation frequencies of 10, 40, and 55 Hz will be discussed. This work contributes to the foundation for a new type of vibration-based characterization experiments and generates initial data on the functional strength of 6061 aluminum under the conditions considered.
A scanning evanescent microwave microscope (SEMM) that uses near-field evanescent electromagnetic waves to probe sample properties is disclosed. The SEMM is capable of high resolution imaging and quantitative measurements of the electrical properties of the sample. The SEMM has the ability to map dielectric constant, loss tangent, conductivity, electrical impedance, and other electrical parameters of materials. Such properties are then used to provide distance control over a wide range, from to microns to nanometers, over dielectric and conductive samples for a scanned evanescent microwave probe, which enable quantitative non-contact and submicron spatial resolution topographic and electrical impedance profiling of dielectric, nonlinear dielectric and conductive materials. The invention also allows quantitative estimation of microwave impedance using signals obtained by the scanned evanescent microwave probe and quasistatic approximation modeling. The SEMM can be used to measure electrical properties of both dielectric and electrically conducting materials.
The Calcine Disposition Project is responsible for retrieval, treatment by hot-isostatic pressure, packaging, and disposal of highly radioactive calcine stored at the Idaho Nuclear Technology and Engineering Center at the Idaho National Laboratory Site in southeast Idaho. In the 2009 Amended Record of Decision: Idaho High-Level Waste and Facilities Disposition Final Environmental Impact Statement the Department of Energy documented the selection of hot-isostatic pressure as the technology to treat the calcine. The Record of Decision specifies that the treatment results in a volume-reduced, monolithic waste form suitable for transport outside of Idaho by a target date of December 31, 2035. That target date is specified in the 1995 Idaho Settlement Agreement to treat and prepare the calcine for transport out of Idaho in exchange for allowing storage of Navy spent nuclear fuel at the INL Site. The project is completing the design of the calcine-treatment process and facility to comply with Record of Decision, Settlement Agreement, Idaho Department of Environmental Quality, and Department of Energy requirements. A systems engineering approach is being used to define the project mission and requirements, manage risks, and establish the safety basis for decision making in compliance with DOE O 413.3B, 'Program and Project Management for the Acquisition of Capital Assets'. The approach draws heavily on 'design-for-quality' tools to systematically add quality, predict design reliability, and manage variation in the earliest possible stages of design when it is most efficient. Use of these tools provides a standardized basis for interfacing systems to interact across system boundaries and promotes system integration on a facility-wide basis. A mass and energy model was developed to assist in the design of process equipment, determine material-flow parameters, and estimate process emissions. Data generated from failure modes and effects analysis and reliability, availability, maintainability, and inspectability analysis were incorporated into a time and motion model to validate and verify the capability to complete treatment of the calcine within the required schedule. The Calcine Disposition Project systems engineering approach, including use of industry-proven design-for-quality tools and quantitative assessment techniques, has strengthened the project's design capability to meet its intended mission in a safe, cost-effective, and timely manner. Use of these tools has been particularly helpful to the project in early design planning to manage variation; improve requirements and high-consequence risk management; and more effectively apply alternative, interface, failure mode, RAMI, and time and motion analyses at the earliest possible stages of design when their application is most efficient and cost effective. The project is using these tools to design and develop HIP treatment of highly radioactive calcine to produce a volume-reduced, monolithic waste form with immobilization of hazardous and radioactive constituents. (authors)
The in-can vitrification process has been developed by the CEA for an internal application (alpha waste treatment) since 2005 and can be rated TRL 7. On these basis the DEM'n'MELT consortium which gathers Orano, CEA and ECM technologies is currently developing and qualifying a robust, simple and versatile in situ vitrification process dedicated to D and D waste. The DEM'n'MELT vitrification process is developed with a modular design, the main characteristics are presented hereafter: - Suitable for high or medium level waste. - Heated by a simple and robust resistance furnace. - Offering homogeneity to the melted mixture. - Suitable for solid or liquid wastes, including zeolites and sludge. - Flexible enough to accommodate uncertainties on waste composition. - Designed in order to produce a small amount of secondary waste. - Implementing proven technological solutions from French high level vitrification shops. - Requiring low investment and operation costs. Regarding this features, the in-can process has been deemed as an appropriate tool for the vitrification of the Fukushima water treatment secondary waste (mineral adsorbants, sludge). The evaluation of the In-can process for Fukushima waste is a project led by Orano, CEA and ANADEC. The main phases are: - Scenarios and glass formulation studies to optimize waste loading and matrix homogeneity. - Bench scale tests on several scenarios of blended waste. - Pilot scale test on one selected scenario (reference scenario). - Feasibility evaluation to Fukushima Daiichi Nuclear Power Station implementation. This paper presents the first results of this project with a highlighting on glass waste loading, glass properties, bench tests and pilot test results, process parameters, and material balance. (authors)
A scanning evanescent microwave microscope (SEMM) that uses near-field evanescent electromagnetic waves to probe sample properties is disclosed. The SEMM is capable of high resolution imaging and quantitative measurements of the electrical properties of the sample. The SEMM has the ability to map dielectric constant, loss tangent, conductivity, electrical impedance, and other electrical parameters of materials. Such properties are then used to provide distance control over a wide range, from to microns to nanometers, over dielectric and conductive samples for a scanned evanescent microwave probe, which enable quantitative non-contact and submicron spatial resolution topographic and electrical impedance profiling of dielectric, nonlinear dielectric and conductive materials. The invention also allows quantitative estimation of microwave impedance using signals obtained by the scanned evanescent microwave probe and quasistatic approximation modeling. The SEMM can be used to measure electrical properties of both dielectric and electrically conducting materials.
This paper outlines a new simplified approach to developing a material model for adobe. The approach is to fit the equation of state (EOS) using a Mie-Gruneisen (MGR) analytical model with a P-Alpha compaction law, and to fit the pressure-dependent yield surface with the Geological Yield Surface (GEO) modeled in CTH using well characterized adobe. By identifying key parameters that governed material response, this simplified modeling approach aimed to increase the understanding of the shock compaction and compression behavior of adobe. The new simplified model for adobe represented in this paper replicated the features of past experimental penetration data. At low velocities the penetration behavior of steel spheres into adobe is captured by Stokes law, where the drag coefficient is inversely proportional to the Reynolds number. Each inherently different adobe material investigated had a separate linear region with the slope equal to the inverse of the coefficient of drag multiplied by impact velocity. A transition region following the Stokes region was identified in each adobe material, where the penetration depth was constant with increasing impact velocity. This penetration depth limit was shown to be dependent upon the yield strength of the adobe and inversely proportional to the initial density. Finally, examining the sensitivity of the penetration depth to the key model parameters, the material model for adobe was adjusted to provide the best fit to the experimental penetration data. In addition, a simplified water content, or initial saturation of the adobe, was introduced as another relevant parameter to characterize the response. Using this simple material model for adobe, validated with experimental penetration data, the response of adobe targets to hypervelocity impact of a variety of projectile types can be reliably predicted.
The influence of the ferroelectric to paraelectric transition on the relaxation parameters of conductive processes in ferroelectric materials is studied in the time domain. Three well-known ferroelectric systems were chosen with transition temperatures in different regions, these are, high-temperature PbNb{sub 2}O{sub 6}-based ceramics; nanostructured Pb(Zr{sub 0.6}Ti{sub 0.4})O{sub 3} ceramics; and submicron BaTiO{sub 3}. The thermal evolution of relaxation parameters shows clear anomalies in their typical behavior when conductivity processes arise in the temperature range where the ferroelectric transition takes place. The method here described allows obtaining information about the correlation between charge transport and the motion of the off-center ions at the phase transition.
Since a large number of the procedures used for inspecting the external tank are concerned with determining flaws in welds, there is a need to develop an inspection technique, which can be automated, to determine flaws in welds and structures with complex geometries. Techniques whereby an eddy current is generated in a metallic material and the changes in the circuit parameters due to material differences are observed, were chosen as one possible approach. Pulsed eddy current and its relationship to multifrequency techniques is discussed as well as some preliminary results obtained from observing pulsed waveforms with apparatus and algorithms currently in use for ultrasonic testing of welds. It can be shown the pulsed eddy current techniques can provide similar results, can eliminate some of the noncritical parameters affecting the eddy current signals, and can facilitate in the detection of critical parameter such as flaws, subsurface voids, and corrosion.
The Advanced Reactor Technologies (ART) Program has established a multi-year plan to develop Alloy 709 advanced stainless steel, generate the data package and develop material-specific design parameters in qualifying it as a new structural material for Class A construction in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors (ASME 2025). In collaboration with material vendors, the Advanced Materials Development activities under ART have successfully scaled the Alloy 709 plate form production from a laboratory heat of 500 pounds to commercial heats totaling 133,000 pounds of Alloy 709 plate fabricated from three heats. The goal of the overall Alloy 709 development program is to establish the necessary microstructural and mechanical properties relationship for Alloy 709 to ultimately develop fabrication parameters for other product forms such as bars, pipes, and forgings using the available ART Alloy 709 materials. This study will enable its deployment in the industry as an advanced construction material for high-temperature components. The objective of this Alloy 709 development work in FY 2025 is to experimentally determine the high-temperature deformation-recrystallization response of the Alloy 709 heats and to experimentally generate true stress-true strain data for Alloy 709 using the available commercial heat plate materials. Integral to this work is the previous characterization of the as-rolled materials and the determination of an effective solution-annealing process, which was reported in Y. Wang et al., 2023, and the evaluation of the effect of controlled cooling on the resultant precipitation in these commercial heats. This report summarizes and builds on the results of the previous reports to assess the high-temperature deformation behavior as a function of deformation temperature, strain and strain rate using commercial Alloy 709 heat 58776-3RB fabricated by G. O. Carlson and heat 529900-02 fabricated by Allegheny Technologies Incorporated (ATI) Specialty Rolled Products.