Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Organofunctional Silane Modification of Aluminum-Doped Zinc Oxide Surfaces as a Route to Stabilization

Aluminum-doped zinc oxide (AZO) is a low-temperature processed transparent conductive oxide (TCO) made of earth abundant elements; its applications are currently limited by instability to heat, moisture, and acidic conditions. We demonstrate that the application of an organofunctional silane modifier mitigates AZO degradation, and explore the interplay between performance and material composition and morphology. Specifically, we evaluate degradation of bare AZO and APTES (3-aminopropyltriethoxysilane)-modified AZO in response to damp heat (DH, 85 °C, 85 % relative humidity) exposure over 1000 h, then demonstrate how surface modification impacts changes in electrical and optical properties, and chemical composition in one of the most thorough studies to date. Hall measurements show that the resistivity of AZO increases due to a decrease in electron mobility, with no commensurate change in carrier concentration. APTES decelerates this electrical degradation, without affecting AZO optical properties. Percent transmission and yellowness index of an ensemble of bare and modified AZO are stable upon DH exposure, but haze increases slightly for a discrete sample of modified AZO. Atomic force microscopy (AFM) and optical profilometer (OP) measurements do not show evidence of pitting or delamination after 1000 h DH exposure, but indicate a slight increase in surface roughness on both the nanometer and micron length scales. X-ray photoelectron spectroscopy data (XPS) reveal that the surface composition of bare and silanized AZO is stable over this time frame; oxygen vacancies, as measured by XPS, are also stable with DH exposure, which, together with transmission and Hall measurements, indicate stable carrier concentrations. However, after 1500 h of DH exposure, only bare AZO shows signs of catastrophic destruction. Comparison of the data presented herein to previous reports indicates that the initial AZO composition and microstructure dictate the degradation profile. Furthermore, this work demonstrates that surface modification slows the bulk degradation of AZO, and provides insight into how the material can be more widely used as a transparent electrode in the next generation of optoelectronic devices.

14 SOLAR ENERGY↗

Protonic ceramic electrochemical cells for hydrogen production and electricity generation: exceptional reversibility, stability, and demonstrated faradaic efficiency

Here, we demonstrate exceptional performance for steam electrolysis at intermediate temperatures (500–650 °C) using protonic ceramic electrolyte cells comprised of the proton-permeable, high-activity mixed conductor PrBa 0.5 Sr 0.5 Co 1.5 Fe 0.5 O 5+δ (PBSCF) as the air electrode, the highly proton-conductive and chemically stable perovskite oxide BaZr 0.4 Ce 0.4 Y 0.1 Yb 0.1 O 3 (BZCYYb4411) as the electrolyte, and a composite of Ni–BZCYYb4411 as the fuel electrode. Cells constructed from this material set have been shown previously to function efficiently in fuel cell mode. We demonstrate here reversible operation, enabling hydrogen production when excess electricity is available and immediate electricity generation from stored hydrogen when power demand is high. The cells are stable under cyclic operation and also under prolonged continuous operation in electrolysis mode, undergoing minimal loss in electrochemical characteristics after 500 h at 550 °C. Microstructurally optimized cells yield a remarkable current density of -1.80 A cm -2 at 600 °C and an operating voltage of 1.3 V, of which, based on an electrochemically deduced faradaic efficiency of 76%, -1.37 A cm -2 contributes to useful hydrogen.

25 ENERGY STORAGE↗

Cross-polarization confocal imaging of subsurface flaws in silicon nitride.

A cross-polarization confocal microscopy (CPCM) method was developed to image subsurface flaws in optically translucent silicon nitride (Si{sub 3}N{sub 4}) ceramics. Unlike conventional confocal microscopy, which measures reflected light so is applicable only to transparent and semi-transparent materials, CPCM detects scattered light from subsurface while filtering out the reflected light from ceramic surface. For subsurface imaging, the refractive-index mismatch between imaging (air) and imaged (ceramic) medium may cause image distortion and reduce resolution in the depth direction. This effect, characterized by an axial scaling factor (ASF), was analyzed and experimentally determined for glass and Si{sub 3}N{sub 4} materials. The experimental CPCM system was used to image Hertzian C-cracks generated by various indentation loads in the subsurface of a Si{sub 3}N{sub 4} specimen. It was demonstrated that CPCM may provide detailed information of subsurface cracks, such as crack angle and path, and subsurface microstructural variations.

36 MATERIALS SCIENCE↗

Molten Salt Assisted Low-Temperature Electro-Catalytic Graphitization of Coal Chars

A great effort has been centered around developing clean energy technologies (energy storage devices) to curtail burning fossil fuels' deleterious environmental effects. Rechargeable batteries [lithium-ion batteries (LIBs)] are among the most invested and investigated storage devices showing potential to transform fossil fuel-powered mobility to next-generation safe electromobility. However, LIBs powered electric vehicles (EV) are expensive due to the high-cost graphite anode associated with LIBs. Herein, the synthesis of low-cost, highly crystalline nano-graphite with a tunable microstructural architecture has been demonstrated via molten salt assisted low-temperature electro-catalytic graphitization of coal chars, traditionally non-graphitizable carbon. Thus, graphite derived from coal chars exhibited nanoflake architecture and delivered high reversible capacity, stable long cycle life, and excellent electrochemical performance under fast charging/discharging conditions (5C, ~12 min charge/discharge time). This finding paves the way to manufacture cost-effective high-energy-density batteries using as-synthesized graphite from readily available coal sources that could propel the EVs to the next level.

25 ENERGY STORAGE↗

NASA-UVA light aerospace alloy and structures technology program (LA(sup 2)ST)

The general objective of the Light Aerospace Alloy and Structures Technology (LA(sup 2)ST) Program is to conduct interdisciplinary graduate student research on the performance of next generation, light weight aerospace alloys, composites, and thermal gradient structures in collaboration with Langley researchers. Specific technical objectives are established for each research project. We aim to produce relevant data and basic understanding of material behavior and microstructure, new monolithic and composite alloys, advanced processing methods, new solid and fluid mechanics analyses, measurement advances, and critically, a pool of educated graduate students for aerospace technologies. Four research areas are being actively investigated, including: (1) Mechanical and Environmental Degradation Mechanisms in Advanced Light Metals and Composites; (2) Aerospace Materials Science; (3) Mechanics of Materials and Composites for Aerospace Structures; and (4) Thermal Gradient Structures.

Gangloff, Richard P.↗

Third-Generation TiAl Alloy Tested: Exhibits Promising Properties for Rotating Components

The Revolutionary Turbine Accelerator/Turbine-Based Combined Cycle (RTA/TBCC) Program for the next-generation launch vehicle has targeted gamma titanium aluminide as a potential compressor and structural material. Because of the high compressor inlet and exit temperatures, the TBCC engine requires higher temperature materials than conventional Ti alloys, and because of its stringent thrust-to-weight requirements, the engine requires low-density material to be utilized wherever possible. Third-generation gamma alloys offer higher temperature capability along with low density and high stiffness. A high-temperature, high-strength *-TiAl alloy with a high Nb-content (Gamma MET PX1) was selected for evaluation. The microstructure and mechanical properties of Gamma Met PX (GMPX) in both the as-extruded and a lamellar heat-treated condition and the influence of the microstructure on the tensile, creep, and fatigue properties were investigated in-house.

Draper, Susan L.↗

Microstructure and nanoindentation of the rostrum of Curculio longinasus Chittenden, 1927 (Coleoptera: Curculionidae)

The rostrum is an extension of the cuticle of the head of weevils (Coleoptera: Curculionidae) and is often used to bore holes for oviposition (the process of laying eggs) into host plant tissue where larval development occurs. In members of the genus Curculio Linnaeus, 1758, the rostrum is long, slender, and strongly curved, but is nevertheless used to excavate straight bore-holes in the fruit of various host plants, through significant deformation of this structure. In this study, scanning electron microscopy (SEM) was used to examine the rostrum of Curculio longinasus Chittenden, 1927, leading to a microstructural model that describes its deformation behavior. Specifically, we used the continuous stiffness measurement (CSM) technique in nanoindentation to measure the Young's modulus and hardness of rostrum. The values of Young's modulus and hardness for the endocuticle were measured to be 8.91 ± 0.93 GPa and 558 ± 60 MPa, respectively. These results are critical for generating accurate finite element models of the head's mechanical behavior while it undergoes deformation. - Highlights: •SEM was used to examine the rostrum of Curculio longinasus Chittenden, 1927. •Nanoindentation to measure the Young's modulus and hardness of rostrum. •Results are critical for finite element models of the head's mechanical behavior.

36 MATERIALS SCIENCE↗

Impact of cobalt doping on structural and magnetic properties of zinc oxide nanocomposites synthesized by mechanical ball-milling method

A series of zinc oxide (ZnO) semiconductor nanocomposite samples doped with different concentrations of cobalt (Co) were successfully synthesized via simple and highly effective mechanical ball-milling method using suitable precursors. All doped nanocomposites crystallized in hexagonal wurtzite formation of ZnO. No alteration in the wurtzite structure, with no evidence of any segregated secondary phase(s) was detected with increasing doping concentrations. This result unambiguously verified the substitution of Zn 2+ sites by Co 2+ ions in the ZnO host lattice for different doping concentrations. Moreover, room temperature ferromagnetic behavior was observed in all doped nanocomposite samples in the reported work. Present study clearly shows that mechanical ball-milling is a facile, inexpensive, eco-friendly method to synthesize crystalline and magnetic Co doped ZnO nanocomposites for next generation spin-based devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tuning the fluid wetting dynamics on gold microstructures using photoactive compounds

This work demonstrates how photoactive compounds can be used to tune the surface chemistry, surface free energy, and the wetting velocity of fluids on Spiropyran functionalized surfaces with different surface microstructures. Evidence of this photowetting effect is based on data showing: (1) the cyclic changes in the static, advancing, and receding contact angles $\theta$ CA for multiple UV$\rightleftarrows$vis photoswitching cycles with both smooth and microstructured surfaces and (2) the changes in the fluid wicking velocity (via UV$\rightleftarrows$vis photoswitching) on different Spiropyran functionalized hemiwicking surfaces. X-ray photoelectron spectroscopy is used to determine the efficiency of photoswitching caused by the quality of the Spiropyran functionalization. Reversible photoisomerization of Spiropyran generates a gradient in surface free energy, resulting in a similar change in contact angle ($\theta$ CA ) in the photoswitchable surfaces. In conclusion, by incorporating these changes into the Owens-Wendt and Van Oss surface energy models, the energy of smooth Au surfaces can also be predicted for both UV and visible light irradiations, where reversible contact angle variations of $\Delta$$\theta$ CA ≈ 5–10° are achieved with both water and water-ethanol mixtures due to the conversion of SP to merocyanine, which corresponds to a total free energy change of ~13% on the photoswitchable surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dynamic recrystallization and texture evolution of Mg–Y–Zn alloy during hot extrusion process

The microstructure and texture evolution of Mg{sub 98.5}Y{sub 1}Zn{sub 0.5} and Mg{sub 92.5}Y{sub 5}Zn{sub 2.5} (atomic percent) alloys during hot extrusion were systematically investigated. The coarse LPSO phases with higher volume fraction (∼ 57%) suppressed the twinning generation in the initial stage of extrusion, and accelerated the dynamic recrystallization through the particle deformation zones. Therefore, the volume fraction of DRXed grains in as-extruded Mg{sub 92.5}Y{sub 5}Zn{sub 2.5} alloy was much higher than that of Mg{sub 98.5}Y{sub 1}Zn{sub 0.5} alloy. The intensive recrystallization process resulted in the conventional basal texture weakening, although the texture evolution was mainly dominated by flow behavior. The dynamic recrystallization behavior in Mg{sub 92.5}Y{sub 5}Zn{sub 2.5} alloy restricted the formation of deformation texture, and thus the more random texture was observed during the whole extrusion process. - Highlights: • The densely coarse LPSO phases suppressed the twinning deformation. • Coarse LPSO phases induced the particle stimulated nucleation effect. • Dynamic recrystallization resulted in the basal texture weakening effect.

36 MATERIALS SCIENCE↗

DISTRIBUTION COEFICIENTS (KD) GENERATED FROM A CORE SAMPLE COLLECTED FROM THE SALTSTONE DISPOSAL FACILITY

Core samples originating from Vault 4, Cell E of the Saltstone Disposal Facility (SDF) were collected in September of 2008 (Hansen and Crawford 2009, Smith 2008) and sent to SRNL to measure chemical and physical properties of the material including visual uniformity, mineralogy, microstructure, density, porosity, distribution coefficients (K{sub d}), and chemical composition. Some data from these experiments have been reported (Cozzi and Duncan 2010). In this study, leaching experiments were conducted with a single core sample under conditions that are representative of saltstone performance. In separate experiments, reducing and oxidizing environments were targeted to obtain solubility and Kd values from the measurable species identified in the solid and aqueous leachate. This study was designed to provide insight into how readily species immobilized in saltstone will leach from the saltstone under oxidizing conditions simulating the edge of a saltstone monolith and under reducing conditions, targeting conditions within the saltstone monolith. Core samples were taken from saltstone poured in December of 2007 giving a cure time of nine months in the cell and a total of thirty months before leaching experiments began in June 2010. The saltstone from Vault 4, Cell E is comprised of blast furnace slag, class F fly ash, portland cement, and Deliquification, Dissolution, and Adjustment (DDA) Batch 2 salt solution. The salt solution was previously analyzed from a sample of Tank 50 salt solution and characterized in the 4QCY07 Waste Acceptance Criteria (WAC) report (Zeigler and Bibler 2009). Subsequent to Tank 50 analysis, additional solution was added to the tank solution from the Effluent Treatment Project as well as from inleakage from Tank 50 pump bearings (Cozzi and Duncan 2010). Core samples were taken from three locations and at three depths at each location using a two-inch diameter concrete coring bit (1-1, 1-2, 1-3; 2-1, 2-2, 2-3; 3-1, 3-2, 3-3) (Hansen and Crawford 2009). Leaching experiments were conducted with a section of core sample 3-2. All cores from location 3 were drilled without using water. Core sample 3-2 was drilled from approximately six inches to a depth of approximately 13 inches. Approximately six inches of the core was removed but it broke into two pieces during removal from the bit. At the time of drilling, core material appeared olive green in color (Smith 2008). The fact that the samples were cored as olive green and were received after storage with a gray outer layer is indicative that some oxidation had occurred prior to leaching studies.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Bayesian inferencing framework for ultrasound wave speed measurements in metal additive manufacturing

Process-related changes during metal additive manufacturing introduce microstructural variability in the material properties of printed parts, directly affecting component reliability. Accurate estimation of these property variations with part performance are essential for quality assurance. Ultrasound testing offers a non-destructive means to estimate mechanical properties and detect defects; however, conventional analysis methods often neglect the influence of microstructural variability, limiting their effectiveness. Here, this research presents a Bayesian inference technique for quantifying wave speed uncertainty from ultrasound measurements of metal additive manufactured parts. By integrating prior ultrasound data with a Bayesian model, the proposed approach generates posterior density estimates of wave speed that systematically account for manufacturing-induced variability and uncertainty. The novelty of this research lies in applying a Bayesian framework to analyze experimental ultrasound measurements within the context of metal additive manufacturing variability. The method enhances the accuracy of wave speed estimation by 64%, defect position by 50% and increases confidence associated with wave speed variance by 30% across different porosity levels, thereby providing a robust foundation for improved decision-making and increased reliability in additively manufactured components.

Additive manufacturing↗

Micro-architecture embedding ultra-thin interlayer to bond diamond and silicon via direct fusion

The continuous demand on miniaturized electronic circuits bearing high power density illuminates the need to modify the silicon-on-insulator-based chip architecture. This is due to the low thermal conductivity of the few hundred nanometer-thick insulator present between the silicon substrate and active layers. The thick insulator is notorious for releasing the heat generated from the active layers during the operation of devices, leading to degradation in their performance and thus reducing their lifetime. To avoid the heat accumulation, we propose a method to fabricate the silicon-on-diamond (SOD) microstructure featured by an exceptionally thin silicon oxycarbide interlayer (~3 nm). While exploiting the diamond as an insulator, we employ spark plasma sintering to render the silicon directly fused to the diamond. Importantly, this process can manufacture the SOD microarchitecture via a simple/rapid way and incorporates the ultra-thin interlayer for minute thermal resistance. The approach invented herein expects to minimize the thermal interfacial resistance of the devices and is thus deemed as a breakthrough appealing to the current chip industry.

36 MATERIALS SCIENCE↗

COWALKER:EFFECTIVE TRANSPORT PROPERTIES OF COMPOSITE MATERIALS

SF-23-026 This software computes effective transport properties of composite materials involving fibers and nanoparticles using a random-walk algorithm that efficiently scales to an arbitrary number of processes and cores. Effective transport properties (thermal, electrical) are key to bridge the microstructure of complex materials with its macroscopic behavior. Traditional approaches either use effective medium approximations (closed mathematical expressions that are approximation for certain conditions) or continuum simulation models such as finite element or finite volume, which require the generation of a mesh for each configuration explored. cowalker leverages the equivalence between laplacian or heat equation-based models and random walks to compute the asymptotic transport properties from an ensemble of first sojourn times of a random walker moving through the composite material. This allows us to directly define a composite material as a collection of particles and use algorithms developed for molecular dynamics to quickly compute the intersection of the walker with the different interfaces in the material. cowalker is developed in C++, and it relies on the GNU Scientific Library for random generation. cowalker is currently delivered as source code, so the GSL library is not included in cowalker's distribution. A more userfriendly version, cowalker.jl is currently in development and will be released as part of cowalker.

YANGUAS-GIL, ANGEL↗

The Analysis of the General Performance and Mechanical Behavior of Unirradiated FeCrAl Alloys Before and After Welding

The present report summarizes and discusses the preliminary results for the in-depth characterization of the modern, nuclear-grade FeCrAl alloys currently under development. The alloys were designed for enhanced radiation tolerance and weldability, and the research is currently being pursued by the Department of Energy (DOE) Nuclear Energy Enabling Technologies (NEET) program. Last year, seven candidate FeCrAl alloys with well-controlled chemistry and microstructures were designed and produced; welding was performed under well-controlled conditions. The structure and general performance of unirradiated alloys were assessed using standardized and advanced microstructural characterization techniques and mechanical testing. The primary objective is to identify the best candidate alloy, or at a minimum to identify the contributing factors that increase the weldability and radiation tolerance of FeCrAl alloys, therefore enabling future generations of FeCrAl alloys to deliver better performance parameters. This report is structured so as to describe these critical assessments of the weldability; radiation tolerance will be reported on in later reports from this program.

36 MATERIALS SCIENCE↗

Mechanical alloying, characterization and consolidation of Ti-Al-Ni alloys

Mechanical alloying is being investigated as a processing route for the production of aluminide intermetallics. This program involves powder production and characterization, consolidation and thermal treatments and determination of microstructure-property relationships. An attritor mill is being used to produce powder in lots up to 1000 grams and the processing parameters are being systematically varied to establish the optimum milling conditions. The mill is being instrumented to generate data related to the processing to provide a basis for theoretical modeling. Powder is being characterized using thermal analysis, optical and electron microscopy and X-ray diffraction. Particle size distributions and powder density are being determined. Consolidation of the powder is being approached in several different ways including, cold isostatic pressing, sintering, extrusion and hot pressing. The results of the program so far will be presented and future directions discussed.

Nash, P.↗

In Situ TEM Microcompression Pillar Size Effects in Fe-9Cr ODS

The objective of this paper is to ascertain the existence of a specimen size threshold, below which the material no longer exhibits bulk mechanical behavior when tested using in situ transmission electron microscopic (TEM) micro-compression pillars. In this work, sub-micron sized pillars of a model Fe-9Cr oxide dispersion strengthened (ODS) alloy were compressed in TEM in situ at room temperature, and attempts have been made to quantify the resulting data. Results are compared to mechanical property values in the archival literature, and a discussion on the validity of quantitative in situ TEM micro-compression data for ODS steel is included. In situ TEM mechanical testing is a relatively new technique enabling concurrent TEM imaging and mechanical testing of sub-micron-sized electron-transparent specimens. Due to limited sample volume of many nuclear materials, in situ TEM mechanical testing holds great promise for advancing our understanding of deformation phenomena. But it is well known that the dramatically reduced specimen size required for in situ testing can affect quantitative and qualitative deformation behaviors. However, Kiener, et al. used in situ TEM micro-compression pillars on irradiated and unirradiated single-crystal copper. They observed size independence in the irradiated material, while the unnirradiated material displayed a size threshold below which the mechanical properties deviated from those of bulk Cu. They assert that the more densely-spaced obstacles in irradiated Cu allow it to display bulk properties even in specimens having ∼ 100 nm dimensions. Similar to Kiener's findings, we hypothesize that unirradiated ODS will demonstrate a size threshold, but the in situ TEM micro-compression technique can be extended from single crystal materials to engineering alloys. An Fe-9Cr model ODS alloy was chosen for this study because of the broad interest in ODS for advanced nuclear reactors. ODS alloys exhibit high irradiation tolerance and high temperature creep resistance. New insight into deformation processes gained through in situ TEM mechanical testing could be valuable for the validation of ODS alloys for next generation nuclear reactors. The fact that the compressive yield stress and elastic modulus do not follow distinct trends as a function of specimen size is likely due to the high density of obstacles to dislocation motion. The ODS microstructure contains such obstacles as oxide nanoparticles, a fine grain structure, a high density of dislocation lines, and carbide precipitates. Since the deformation behavior is governed by the minimum separation distance between obstacles [1], it is plausible that the high obstacle density enables ODS alloy micropillars to exhibit bulk-like mechanical properties even prior to irradiation. Future work will focus on: (1) developing finite element models to help explain the difference in elastic moduli between bulk and micropillar tests, (2) understanding the spread in yield stress measurements at fixed micropillar volumes, and (3) extending this study to irradiated ODS. (authors)

36 MATERIALS SCIENCE↗

A new method for isolating plasma interactions from those of the laser beam during plasma nitriding

Highlights: • Nitriding of titanium was studied using a laser sustained plasma (LSP) reactor, independent of the laser beam. • Nucleation and growth of faceted, dendritic, rectangular and particulate TiN morphologies was observed. • TiN layers up to 300 μm thick formed within 5 s - one of the most rapid TiN growth rates observed for LSP/laser nitriding. • LSP accessed novel microstructures compared to laser nitriding with or without surface-struck plasm plasma. - Abstract: A new method for separating the interactions of a laser plasma from those of a laser beam with a titanium substrate was developed. A laser-sustained plasma (LSP) was generated by striking the plasma on a titanium plate in a flowing nitrogen atmosphere at ambient pressure and subsequently removing the strike plate. The resultant nitrogen plasma was sustained indefinitely around the laser focal plane until the nitrogen gas flow and/or the laser power were switched off. The laser-sustained nitrogen plasma was then used as a “reactor” to study the effects of a nitrogen plasma, independent of the laser beam, when the plasma was brought into close proximity, (2 to 3 mm), parallel to a titanium substrate. There was no interaction of the parallel laser beam with the substrate. Heat, nitrogen and titanium were exchanged between the nitrogen LSP and substrate resulting in melting, nucleation and growth of faceted and dendritic TiN crystals, rectangular hollow TiN morphologies and particulate TiN deposits. Dense TiN layers up to 300 μm thick formed within 5 s. The results demonstrated that compositionally graded layers of nitrogen-enriched titanium, and titanium nitride could be formed very rapidly on model, commercially-pure titanium substrates, with promise for extension to commercial alloys such as Ti-6Al-4V.

36 MATERIALS SCIENCE↗