Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

The Athena Microscopic Imager Investigation

The Athena science payload on the Mars Exploration Rovers (MER) includes the Microscopic Imager (MI) [1]. The MI is a fixed-focus camera mounted on the end of an extendable instrument arm, the Instrument Deployment Device (IDD; see Figure 1).The MI was designed to acquire images at a spatial resolution of 30 microns/pixel over a broad spectral range (400 - 700 nm; see Table 1). Technically, the microscopic imager is not a microscope: it has a fixed magnification of 0.4 and is intended to produce images that simulate a geologist s view through a common hand lens. In photographers parlance, the system makes use of a macro lens. The MI uses the same electronics design as the other MER cameras [2, 3] but has optics that yield a field of view of 31 31 mm across a 1024 1024 pixel CCD image (Figure 2). The MI acquires images using only solar or skylightillumination of the target surface. A contact sensor is used to place the MI slightly closer to the target surface than its best focus distance (about 66 mm), allowing concave surfaces to be imaged in good focus. Because the MI has a relatively small depth of field (3 mm), a single MI image of a rough surface will contain both focused and unfocused areas. Coarse focusing will be achieved by moving the IDD away from a rock target after the contact sensor is activated. Multiple images taken at various distances will be acquired to ensure good focus on all parts of rough surfaces. By combining a set of images acquired in this way, a completely focused image can be assembled. Stereoscopic observations can be obtained by moving the MI laterally relative to its boresight. Estimates of the position and orientation of the MI for each acquired image will be stored in the rover computer and returned to Earth with the image data. The MI optics will be protected from the Martian environment by a retractable dust cover. The dust cover includes a Kapton window that is tinted orange to restrict the spectral bandpass to 500-700 nm, allowing color information to be obtained by taking images with the dust cover open and closed. The MI will image the same materials measured by other Athena instruments (including surfaces prepared by the Rock Abrasion Tool), as well as rock and soil targets of opportunity. Subsets of the full image array can be selected and/or pixels can be binned to reduce data volume. Image compression will be used to maximize the information contained in the data returned to Earth. The resulting MI data will place other MER instrument data in context and aid in petrologic and geologic interpretations of rocks and soils on Mars.

K E Herkenhoff↗

Roughness-Dominated Transition on Nosetips, Attachment Lines and Lifting-Entry Vehicles

Modeling of roughness-dominated transition is a critical design issue for both ablating and non-ablating thermal protection systems (TPS). Ablating TPS, used for planetary-entry and earth-return missions, first experience recession under high-altitude, low-Reynolds-number conditions. Such laminar-flow ablation causes the formation of a surface microroughness pattern characteristic of the TPS material composition and fabrication process. For non-ablating TPS, such as the overlapping-tile, metallic heatshields proposed for future reusable launch vehicles, the surface roughness pattern is established a priori by the engineering design and assembly procedure. In both cases, these distributed surface roughness patterns create disturbances within, and alter the mean velocity profile of, the laminar boundary layer flowing over the surface. As altitude decreases, Reynolds number increases, and flow field conditions capable of amplifying these roughness-induced perturbations are eventually achieved, i.e., transition onset occurs. Boundary layer transition to turbulence results in more severe heat-transfer rates. Ablating TPS experience increased recession rates, leading to potential bum-through, while non-ablating TPS experience accelerated temperature rise, leading to potential melting of key components.

Reda, Daniel C.↗

Effect of deposition temperature on surface morphology and magnetic properties in epitaxial CoFe{sub 2}O{sub 4} thin films deposited by MOCVD.

We have successfully grown epitaxial CoFe{sub 2}O{sub 4} (CFO) thin film on SrTiO{sub 3} by metal organic chemical vapor deposition. In order to understand the surface structure and its correlation with magnetic properties, CFO thin films were deposited at a range of deposition temperatures. As the deposition temperature is decreased, a huge effect on film morphology and surface roughness is observed, resulting from a change in the size and density of the crystal nuclei. These changes to grain structure and surface roughness modify the energy landscape of the films and are major contributors to the change in magnetic properties as a function of deposition temperature: the direction of the easy axis is aligned in-plane at lower deposition temperatures and lower anisotropy between different directions is observed in the rough films grown at high temperature.

36 MATERIALS SCIENCE↗

Literature Review on the Theory and Measurement of Dry Sliding Friction of Metals

Understanding the friction behavior between two sliding bodies can inform the design of machines, processing of materials, and simulation of dynamic processes. Kinetic friction is a complex phenomenon that depends on a multitude of factors such as sliding velocity, normal force, contact area, surface roughness, material properties, lubrication conditions, and thermal effects. This literature review covers the major known effects of sliding velocity, normal load, and surface roughness on the measured kinetic friction coefficient in the context of microscopic friction phenomena. Classic macroscale friction models are reviewed to illustrate approaches for simulating friction behavior. Prominent experimental friction setups within the literature are discussed with respect to achievable velocity and pressure regimes. The background information gathered here will be used to inform experimental procedures and modeling strategies of the exploratory research (ER) project titled “Measurement of Dynamic Friction via Kolsky Bar” (20200418ER).

36 MATERIALS SCIENCE↗

Study of the ablative effects on tektite

The tumbling and surface roughness effects on the trajectory of entry tektite were studied in both free molecular and continuum flows. It is shown that, while surface roughness has negligible effect on trajectory, the tumbling may play an important role in tektite trajectory and the consequent ablation, provided the body shape is different from a sphere. A shape factor B was proposed to measure the shape irregularity and is found to be a good parameter for correlations between body shape and tumbling effects.

Chen, K. K.↗

Study of the ablative effects on tektite

The tumbling and surface roughness effects on the trajectory of entry tektite are studied in both free molecular and continuum flows. It was concluded that, while surface roughness has negligible effect on trajectory, the tumbling may play an important role in tektite trajectory and the consequent ablation, provided the body shape is different from a sphere. A shape factor was a good parameter for correlations between body shape and tumbling effects.

Chen, K. K.↗

Tribological Characterization of SiC and B{sub 4}C Manufactured by Plasma Pressure Compaction

The objective of the present study was to assess the tribological properties and the wear behavior of silicon carbide and boron carbide ceramics, produced by the plasma pressure compaction sintering process. Reciprocating sliding tests were executed to evaluate the tribological behavior of silicon carbide and boron carbide. Samples of each material with distinct values of surface roughness Ra were tested. Wear mass loss, coefficients of friction and wear mechanism of the boron carbide and silicon carbide were evaluated by means of microscopes and an energy-dispersive spectroscopy probe. The coefficient of friction of the evaluated boron carbide was found to be 0.8, and the surface roughness affects only the starting transient, while for silicon carbide the steady-state value ranges from 0.5 to 0.8 depending on the roughness value Ra.

36 MATERIALS SCIENCE↗

Sputtering of silicon and glass substrates with polyatomic molecular ion beams generated from ionic liquids

The effect of irradiating 1-ethyl-3-methylimidazolium positive (EMIM{sup +}) or dicyanamide negative (DCA{sup –}) ion beams using an ionic liquid ion source was characterized concerning its sputtering properties for single crystalline Si(100) and nonalkaline borosilicate glass substrates. The irradiation of the DCA{sup –} ion beam onto the Si substrate at an acceleration voltage of 4 and 6 kV exhibited detectable sputtered depths greater than a couple of nanometers with an ion fluence of only 1 × 10{sup 15} ions/cm{sup 2}, while the EMIM{sup +} ion beam produced the same depths with an ion fluence 5 × 10{sup 15} ions/cm{sup 2}. The irradiation of a 4 kV DCA{sup –} ion beam at a fluence of 1 × 10{sup 16} ions/cm{sup 2} also yields large etching depths in Si substrates, corresponding to a sputtering yield of Si/DCA{sup – }= 10, and exhibits a smoothed surface roughness of 0.05 nm. The interaction between DCA{sup –} and Si likely causes a chemical reaction that relates to the high sputtering yield and forms an amorphous C-N capping layer that results in the smooth surface. Moreover, sputtering damage by the DCA{sup –} irradiation, which was estimated by Rutherford backscattering spectroscopy with the channeling technique, was minimal compared to Ar{sup +} irradiation at the same condition. In contrast, the glass substrates exhibited no apparent change in surface roughnesses when sputtered by the DCA{sup –} irradiation compared to the unirradiated glass substrates.

42 ENGINEERING↗

Lava flow topographic measurements for radar data interpretation

Topographic profiles at 25- and 5-cm horizontal resolution for three sites along a lava flow on Kilauea Volcano are presented, and these data are used to illustrate techniques for surface roughness analysis. Height and slope distributions and the height autocorrelation function are evaluated as a function of varying lowpass filter wavelength for the 25-cm data. Rms slopes are found to increase rapidly with decreasing topographic scale and are typically much higher than those found by modeling of Magellan altimeter data for Venus. A more robust description of the surface roughness appears to be the ratio of rms height to surface height correlation length. For all three sites this parameter falls within the range of values typically found from model fits to Magellan altimeter waveforms. The 5-cm profile data are used to estimate the effect of small-scale roughness on quasi-specular scattering.

Campbell, Bruce A.↗

Local-Scale Simulations of Nucleate Boiling on Micrometer Featured Surfaces: Preprint

A high-fidelity computational fluid dynamics (CFD)-based model for bubble nucleation of the refrigerant HFE7100 on micrometer-featured surfaces is presented in this work. The single-fluid incompressible Navier-Stokes equations, along with energy transport and natural convection effects are solved on a featured surface resolved grid. An a priori cavity detection method is employed to convert raw profilometer data of a surface into well-defined cavities. The cavity information and surface morphology are represented in the CFD model by geometric mesh deformations. Surface morphology is observed to initiate buoyancy-driven convection in the liquid phase, which in turn results in faster nucleation of cavities. Simulations pertaining to a generic rough surface show a trend where smaller size cavities nucleate with higher wall superheat. This local-scale model will serve as a self-consistent connection to larger device scale continuum models where local feature representation is not possible.

97 MATHEMATICS AND COMPUTING↗

Bidirectional reflectance properties of iron-nickel meteorites

The effects of viewing geometry and small-scale (less than 1 mm) surface roughness on the bidirectional reflectance of iron-nickel meteorites were investigated by measuring the reflectance properties of Gibeon and Canyon Diablo iron-nickel meteorites. Several cut surfaces of each of these meteorites were polished with abrasive grits to controlled surface roughness, and a series of bidirectional reflectance spectra were taken at a variety of viewing geometries using NASA's RELAB facility. The measurements show that, for optically smooth surfaces, only the specular component of reflectance exhibited red-sloped continuum characteristic of iron. Spectra of surfaces that were much rougher than the wavelength of incident light exhibited iron's characteristic red sloped continuum and could be modeled by linear combinations of facets that are oriented in specular and nonspecular geometries with respect to the observer. Spectra of this latter type exhibit good agreement with the published spectra of M-type asteroids.

Britt, D. T.↗

River and lake ice conditions as determined from AIRSAR imagery

Synthetic aperture radar (SAR) imagery data can provide information on types and distribution of river and lake ice needed for studying river ice processes and dynamics, monitoring ice during winter navigation, and formulating ice control strategies. Visible and IR remote sensing systems cannot provide such data and present field methods are inadequate for characterizing ice conditions over long river reaches. Our ongoing analysis of JPL's AIRSAR imagery data and concurrent ground truth of ice conditions on the Tanana River and surrounding lakes near Fairbanks, Alaska, in March 1988, has resulted in several findings: hummocked ice covers and zones of variable ice surface roughness within them can be differentiated; C- and L-band data are more sensitive than P-band to the range of surface roughnesses encountered; smooth, level ice that is clear or contains small bubbles produces little backscatter; snow-covered river ice, whether rough or smooth, is distinguishable from snow-covered river sediments on exposed river beds and unvegetated bars; and open water leads are readily distinguished.

Melloh, Rae A.↗

Room-temperature phonon boundary scattering below the Casimir limit

Thermal conductivity data for rough surface silicon nanowires suggest the breakdown of the Casimir limit which assumes completely diffuse phonon boundary scattering. We show that coherent effects in phonon transport at room temperature indeed lead to such breakdown. Correlated multiple scattering of phonons off the rough surface lead to a reduced thermal conductivity that is dependent not only on the roughness amplitude but more importantly on the roughness correlation length. A correlation length less than the diameter of the wire is typically necessary for lowering the thermal conductivity below the Casimir limit. Our model explains seeming anomalies in data reported for electrolessly etched and electron beam lithography defined nanowires.

Sadhu, J↗

Influence of aerodynamic roughness length on aeolian processes: Earth, Mars, Venus

The aerodynamic roughness length (z sub 0) is the height at which a wind profile assumes a zero velocity. The lower part of the atmospheric boundary layer will be impeded by friction with the surface. An increase in surface roughness will also increase the shear stress required to initiate particle entrainment by the wind. Bagnold (1941) estimated z sub 0 as being 1/30 of the mean particle size. In Nature, surface roughness is composed of nonerodible elements as well as sand-size erodible particles. To assess z sub 0 values as a function of terrain, field experiments were conducted to obtain wind profiles monitored over natural surfaces at 15 sites in the Mojave Desert, Death Valley, and Nye County, Nevada. These sites span a variety of arid-land terrains, including smooth playas, alluvial fans, and lava flows; z sub 0 values ranged from 0.0001 cm to 1 cm. These values were incorporated in a threshold model and a flux model to assess transport efficiency over such terrains in three planetary environments (Venus, Earth, and Mars), and for particle sizes ranging from 60-500 micron. Threshold and flux are a function of planetary environment, particle density and size (Dp), and z sub 0, and the shear velocity of 1.2 x U sub *t (for Dp = 250 micron and z sub 0 = 0.84). Results show that flux on Mars is approximately 14 g/(cm x s), on Earth it is approximately 3 g/(cm x s), and on Venus 0.5 g/(cm x s). Under all planetary environments, the results also show a dramatic decrease in the flux for particles greater than 200 microns when z sub 0 increases above 0.0085 cm (corresponding to sites consisting of alluvium). When z sub 0 approaches 0.03 cm (corresponding to a mantled pahoehoe lava), the flux diminishes.

Blumberg, Dan G.↗

Development of Additively Manufactured Complex Tools for Autoclave Cure Composites

IACMI Project 4.9, Tooling for Composites with Washout Features Produced by Additive Manufacturing, assembled a team including the industry lead, Ability Composites, NREL and Colorado State University (CSU). Ability Composites had originally expressed interest in alternate methods of producing tooling for composite parts. In follow-up discussions, it became clear that one of the bigger tooling challenges revolved around small production volume composite parts that were tooled on washout material due to the complex geometry. To build an understanding of the potential, both from a technology and a cost perspective, for replacing conventional washout tooling with 3D printed thermoplastic tooling, a number of commercially available dissolvable FDM printing materials were evaluated, leading to tooling representative of commercial articles of interest to Ability Composites. Ultimately, Ability Composites was able to directly compare autoclave processed prepreg composite parts produced on conventional washout tooling to composite parts molded on 3D printed dissolvable tooling produced at CSU. Small, laboratory test specimens were developed to investigate the structural performance of the candidate materials under autoclave processing conditions, which were nominally 121 °C (250 °F) and 345 kPa (50 psi). In addition, several internal structural configurations (infills) were evaluated under autoclave conditions using model materials. The results of these tests indicated that two materials, Stratasys ST 130 and Infinite Materials Solutions Aquasys 180 (AQ 180), were the best candidates, given the specified autoclave processing conditions. ST-130 was slightly more robust than AQ-180; however, the AQ-180 was carried forward as it was dissolvable in water, not requiring the basic solution needed to dissolve ST-130. Based on the preliminary material and 3D printed structures evaluations, larger tools with a truncated square pyramid geometry were created to produce prepreg composite test articles for 3D printed dissolvable tool evaluation under standard autoclave fabrication conditions. Two tools were manufactured using ST-130 and one tool using traditional ceramic washout tooling media. The tools were evaluated for geometric fidelity and surface roughness changes before and after carbon fiber/epoxy prepreg composites were manufactured on the tooling. The autoclave processing did not impact the geometry significantly and was completed at 121 °C and 345 kPa, indicating satisfactory tool performance. The results from surface roughness testing of both the resulting composite and the associated tooling indicated that an adequate surface resulted without the need for a surface sealing step, as was required for the conventional washout tooling. Based on results of the truncated pyramid tests as a basis, ST-130, AQ-120 and AQ-180 materials were carried forward to the tool geometry of interest to Ability Composites. These hollow rectangular bent ducts, which were complex in nature and not extractable after cure, were used to understand the impacts of tool material and thickness. One ST-130 tool was produced as a partially solid part, with an enclosed 40% dense infill region to reduce weight and material use. This was the same approach evaluated in the truncated pyramid portion of the study. This tool was to be envelope vacuum bagged and directly compared to a monolithic tool of conventional washout material. The traditional monolithic ceramic tool was manufactured by Ability composites using CNC-based subtractive methods. An additional five dissolvable polymer tools, manufactured from ST-130, AQ-120, and AQ-180, using a hollow design were 3D printed and used to produce carbon fiber/epoxy composite evaluation articles. These hollow dissolvable tools were expected to be less influenced by the autoclave conditions as the wall was solid and vacuum bagging was inside and outside the tool. This alternative geometry was also evaluated as an option in techno-economic modeling. Print times were reduced from in excess of 3 days to under 30 hours, while surface quality and and tool integrity were substantially improved in the transition from the partially solid tool to the hollow tooling concept. Ability Composites produced autoclave-cured prepreg ducts on each of these tools. The autoclave conditions utilized were more severe than those of the initial trials, reaching temperatures of 160 °C and a pressure of 414 kPa. Under these conditions, the partially solid 3D printed tool with skin and 40% dense infill crushed significantly; however, the thicker ST-130 hollow tool showed good promise, deforming only slightly. The thinner hollow tool walls were unsuccessful as were the other materials. Overall, the hollow tool manufacturing process saved significant amounts of time and material in manufacturing as compared to the solid ducts and produced composite surface quality improvements compared to the traditional washout tooling. The TEM was developed to allow direct comparisons between conventional washout tool manufacturing processes and those developed at CSU. It also allowed for two separate 3D printed tool geometries to be analyzed and compared. In this case, the square bent duct tool geometry was determined to be representative of common washout tools. This geometry was compared with a scaled-up version of it to assess differences in the two manufacturing processes based on tool size. The model was developed to make use of user input in the form of geometry details, process steps, manufacturing parameters, bulk material costs, capital equipment costs, and general costs to calculate overall labor, material, capital equipment, and energy costs per manufactured tool for the conventional and additive manufacturing processes for the two representative geometries. It was also able to estimate step-by-step process times for the manufacturing process and geometries. Based on significant input from Ability Composites and CSU from their knowledge gained from hands-on manufacturing of the 3D printed bent duct tool geometry, costs and process times were calculated for the two manufacturing processes. Results showed that the additive manufacturing techniques developed at CSU can substantially reduce the costs of tool manufacturing by reducing labor times and material usage. This is because additive manufacturing is a relatively hands-off process and allows for the tool design to be optimized to reduce material usage. The disadvantage, however, is that process times for additive manufacturing are significantly longer. The three-dimensional (3D) printing process is slow if tight tolerances are required, but the analysis did show that print times could be reduced with the hollow tool geometry. Also, further advances in additive manufacturing could expedite the process. Costs and process times for the tool washout process were calculated separately. They showed that costs are relatively insignificant when compared to the overall tool manufacturing processes, but with increases in tool size, costs for the conventional manufacturing approach are larger than for additive manufacturing. Again, the washout process for conventional tools is very hands-on, whereas for additively manufactured tools the print medium is dissolved in an automated detergent bath at the sacrifice of process time. The analysis showed that optimizing the additively manufactured tools may also reduce washout times. Overall, Project 4.9 demonstrated that commercially available dissolvable 3D printing materials exist that can be used to produce dissolvable tooling capable of surviving prepreg composites fabrication under autoclave conditions of 121 °C (250 °F) and 345 kPa (50 psi). An alternative hollow dissolvable tool design was developed which was structurally superior to the initial concept and was cost and time effective versus conventional washout tooling. The 3D printed sacrificial tool required no added surface sealing steps prior to composite part layup and cure, offering a significant advantage over the porous conventional washout tooling.

36 MATERIALS SCIENCE↗

CO 2 –Brine Contact Angle Measurements on Navajo, Nugget, Bentheimer, Bandera Brown, Berea, and Mt. Simon Sandstones

In this study, contact angles were measured for CO 2 bubbles on six different sandstones (Navajo, Nugget, Bentheimer, Bandera Brown, Berea, and Mt. Simon) that could potentially represent properties of CO 2 storage depositional environments. The impacts of pressure and temperature were studied by focusing on the CO 2 phase behavior in three different scenarios: gaseous, liquid, and supercritical conditions. Despite controlling the sample preparation and cleanliness, CO 2 -brine equilibration conditions, and pressure and temperature, there were inconsistencies in contact angle trends that could largely be attributed to natural sample heterogeneity resulting from localized variations in topography, surface roughness, and mineral composition across the surface. Despite these variations, the analysis of 298 measurements from this study showed that 81% of the contact angles were below 40° representing strongly water-wet to (moderately) water-wet behaviors. Also, 17.3% of the measurements were between 40° and 60° (weakly water-wet) and primarily belonged to small CO 2 bubbles (< 500 μm) that were heavily impacted by localized surface heterogeneity in natural sandstone samples. Additionally, only 1.7% of the measurements had angles greater than 60° and could be classified as CO 2 -wet behavior, but these measurements occurred on extremely small bubbles (100-200 μm) that were very dependent on localized surface heterogeneity. While some of the detailed physics of the CO 2 -brine-sandstone interface is still poorly understood, from an application standpoint, the sandstones of this study were best characterized as strongly water-wet to (moderately) water-wet.

03 NATURAL GAS↗

Synthesis and x-ray characterization of sputtered bi-alkali antimonide photocathodes

Advanced photoinjectors, which are critical to many next generation accelerators, open the door to new ways of material probing, both as injectors for free electron lasers and for ultra-fast electron diffraction. For these applications, the nonuniformity of the electric field near the cathode caused by surface roughness can be the dominant source of beam emittance. Therefore, improving the photocathode roughness while maintaining quantum efficiency is essential to the improvement of beam brightness. Here in this article, we report the demonstration of a bi-alkali antimonide photocathode with an order of magnitude improved roughness by sputter deposition from a K 2 CsSb sputter target, using in situ and operando X-ray characterizations. We found that a surface roughness of 0.5 nm for a sputtered photocathode with a final thickness of 42 nm can be achieved while still yielding a quantum efficiency of 3.3% at 530 nm wavelength.

36 MATERIALS SCIENCE↗

Spectroellipsometric investigation of optical, morphological, and structural properties of reactively sputtered polycrystalline AlN films

The optical and morphological properties of reactively sputtered AlN films on Si substrates have been studied in this work from a self-consistent three-layer optical model developed from spectroscopic-ellipsometry analysis and validated by observations from transmission-electron microscopy, Auger electron spectroscopy, and in situ reflectance interferometry. These properties correlate to the film microstructural properties. Accordingly, the almost thickness-independent refractive index of 2.01 of the bulk AlN layer indicates its polycrystalline microstructure. This layer also appears ungraded, homogeneous, isotropic, and free of excess Al, as if grown through a steady process. The small film absorption points to the Urbach tail states produced by the structural disorder typical of such sputtered films. The films' interface layer consists of a graded Bruggeman intermix of outdiffused Si and AlN materials spreading over 10-12 nm thickness. The surface morphology includes an Al{sub 2}O{sub 3}-oxidized outer rough surface gradually becoming AlN bulk with diminishing amounts of Al{sub 2}O{sub 3} and inner pores. The increase in the surface-layer thickness, as the film grows, indicates further surface roughening due to enlarging crystals in a disoriented growth. This spectroscopic-ellipsometry analysis of AlN films has allowed us to study the effect of substrate biasing on the AlN microstructure and to place forward a new processing method for the surface smoothening of rough AlN and diamond films.

36 MATERIALS SCIENCE↗