Search NASA⌕ Search

SEARCH · Search NASA

Results for “stream flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Turbulent Boundary Layers in Oscillating Flows. Part 1: an Experimental and Computational Study

An experimental-computational study of the behavior of turbulent boundary layers for oscillating air flows over a plane surface with a small favorable mean pressure gradient is described. Experimental studies were conducted for boundary layers generated on the test section wall of a facility that produces a flow with a mean free stream velocity and a superposed nearly-pure sinusoidal component over a wide range of frequency. Flow at a nominal mean free stream velocity of 50 m/s were studied at atmospheric pressure and temperature at selected axial positions over a 2 m test length for frequencies ranging from 4 to 29 Hz. Quantitative experimental results are presented for unsteady velocity profiles and longitudinal turbulence levels obtained from hot wire anemometer measurements at three axial positions. Mean velocity profiles for oscillating flows were found to exhibit only small deviations from corresponding steady flow profiles, while amplitudes and phase relationships exhibited a strong dependence on axial position and frequency. Since sinusoidal flows could be generated over a wide range of frequency, studies at fixed values of reduced frequency at different axial positions were studied. Results show that there is some utility in the use of reduced frequency to correlate unsteady velocity results. The turbulence level u' sub rms was observed to vary essentially sinusoidally around values close to those measured in steady flow. However, the amplitude of oscillation and phase relations for turbulence level were found to be strongly frequency dependent. Numerical predictions were obtained using an unsteady boundary layer computational code and the Cebeci-Smith and Glushko turbulence models. Predicted quantities related to unsteady velocity profiles exhibit fair agreement with experiment when the Cebeci-Smith turbulence model is used.

Cook, W. J.↗

Radial alignment simulation of solar wind streams observed by Pioneers 10 and 11 in 1974

A particularly favorable radial lineup between spacecraft in Earth orbit and Pioneers 10 and 11 (near the ecliptic plane at approximately 5.5 AU and approximately 4.5 AU, respectively) occurred in mid-1974, when the solar corona was in a stable and well-defined warped-dipole configuration. The radial alignment study reported here differs from previous applications of the technique in two respects: (1) It is the first time a two-dimensional (2-D) MHD model has been tested over such a lengthy propagation interval; the 2-D capability is crucial for treatment of the nonradial shearing motions occurring across the stream interface. (2) The three-dimensional (3-D) structure observed in the white light corona at that time is related to the systematic patterns of nonradial flow deflections appearing at the Pioneer corotating interaction region (CIR) fronts. Comparison of predicted and observed flows for pairs of streams in two successive rotations reveals that when the parent coronal hole projects far across the solar equator in a predominantly north-south orientation (i.e., nearest the 2-D idealization), the mapping is accurate down to details of the flow structures. But where the spacecraft tracks along a latitudinal boundary of a hole or the associated stream front is inclined at a shallow angle to the equator, the numerical projections deviate systematically from the observations. Among the sources of error are 3-D dynamical interactions neglected in the model, differential rotation effects, and slow temporal evolution of the coronal structures. A characteristic pattern of north-south and east-west deflections indicative of the 3-D geometry appears across the CIRs, but these patterns evidently reflect primarily the local, as opposed to global, orientation of the 3-D stream fronts. Such patterns appear common in CIRs observed by Pioneer during this period. These findings thus hold special relevance for the analysis of Ulysses observations, since the present coronal configuration is similar to that of 1974.

Pizzo, V. J.↗

Vibrational and rotational analysis of the emission spectra of the arc jet flow

Applying atomic and molecular physics to the analysis of the radiation emitted from the arc jet flow provides a means for determining the species and excitation temperature of the constituents of the flow. A rotational and vibrational analysis of the spectra obtained from the radiation emitted in the shock layer and in the free stream of the jet flow was performed, specifically, in the shock layer bands of the First Negative Group of ionized molecular nitrogen and in the free stream of the gamma-system of nitric oxide.

Blount, Charles E.↗

Fluidic Control of Nozzle Flow: Some Performance Measurements

Results are presented of an experimental program that investigated the use of a secondary air stream to control the amount of flow through a convergent-divergent nozzle. These static tests utilized high pressure, ambient temperature air that was injected at the throat of the nozzle through an annular slot. Multiple injection slot sizes and injection angles were tested. The introduction of secondary flow was made in an opposing direction to the primary flow and the resulting flow field caused the primary stream to react as though the physical throat size had been reduced. The percentage reduction in primary flow rate was generally about twice the injected flow rate. The most effective throttling was achieved by injecting through the smallest slot in an orientation most nearly opposed to the approaching primary flow. Thrust edliciency, as measured by changes in nozzle thrust coefficient, was highest at high nozzle pressure ratios, NPR. The static test results agreed with predictions obtained prior from PABSD, a fully viscous computational fluid dynamics program. Since use of such an injection system on gas turbine engine exhaust nozzles would be primarily at high NPRs, it was concluded that fluidic control holds promise for reducing nozzle weight and complexity on future systems.

Federspiel, John↗

Hydrology Outweighs Temperature in Driving Production and Export of Dissolved Carbon in a Snowy Mountain Catchment

Abstract Terrestrial production and export of dissolved organic and inorganic carbon (DOC and DIC) to streams depends on water flow and biogeochemical processes in and beneath soils. Yet, understanding of these processes in a rapidly changing climate is limited. Using the watershed‐scale reactive‐transport model BioRT‐HBV and stream data from a snow‐dominated catchment in the Rockies, we show deeper groundwater flow averaged about 20% of annual discharge, rising to ∼35% in drier years. DOC and DIC production and export peaked during snowmelt and wet years, driven more by hydrology than temperature. DOC was primarily produced in shallow soils (1.94 ± 1.45 gC/m 2 /year), stored via sorption, and flushed out during snowmelt. Some DOC was recharged to and further consumed in the deeper subsurface via respiration (−0.27 ± 0.02 gC/m 2 /year), therefore reducing concentrations in deeper groundwater and stream DOC concentrations at low discharge. Consequently, DOC was primarily exported from the shallow zone (1.62 ± 0.96 gC/m 2 /year, compared to 0.12 ± 0.02 gC/m 2 /year from the deeper zone). DIC was produced in both zones but at higher rates in shallow soils (1.34 ± 1.00 gC/m 2 /year) than in the deep subsurface (0.36 ± 0.02 gC/m 2 /year). Deep respiration elevated DIC concentrations in the deep zone and stream DIC concentrations at low discharge. In other words, deep respiration is responsible for the commonly‐observed increasing DOC concentrations (flushing) and decreasing DIC concentrations (dilution) with increasing discharge. DIC export from the shallow zone was ~66% of annual export but can drop to ∼53% in drier years. Numerical experiments suggest lower carbon production and export in a warmer, drier future, and a higher proportion from deeper flow and respiration processes. These results underscore the often‐overlooked but growing importance of deeper processes in a warming climate.

54 ENVIRONMENTAL SCIENCES↗

Analysis and representation of complex structures in separated flows

We discuss our recent work on extraction and visualization of topological information in separated fluid flow data sets. As with scene analysis, an abstract representation of a large data set can greatly facilitate the understanding of complex, high-level structures. When studying flow topology, such a representation can be produced by locating and characterizing critical points in the velocity field and generating the associated stream surfaces. In 3D flows, the surface topology serves as the starting point. The 2D tangential velocity field near the surface of the body is examined for critical points. The tangential velocity field is integrated out along the principal directions of certain classes of critical points to produce curves depicting the topology of the flow near the body. The points and curves are linked to form a skeleton representing the 2D vector field topology. This skeleton provides a basis for analyzing the 3D structures associated with the flow separation. The points along the separation curves in the skeleton are used to start tangent curve integrations. Integration origins are successively refined to produce stream surfaces. The map of the global topology is completed by generating those stream surfaces associated with 3D critical points.

Helman, James↗

A Report on Stochastic Fairness Queueing (SFQ) Experiments

SRI International (SRI) has developed an improved queueing algorithm, known as Stochastic Fairness Queueing (SFQ), for best-effort traffic (i.e., traffic that does not require any guaranteed service). SFQ is a probablistic variant of strict fair queueing where instead of a single queue being allocated per flow, a fixed number of queues are used and a hash function maps the IP source and destination to a particular queue. A seed to the hash function is also perturbed occasionally to help distribute the flows amongst different queues when more than one flow maps to the same queue during the lifetime of the flow. SFQ provides 'fair' access by trying to ensure that each flow from source to destination host obtains equal access to the available bandwidth. This report covers a series of experiments performed on DARTnet evaluating the behavior and performance of SFQ against a FIFO queueing discipline. These experiments were designed to show SFQ's advantages and performance, and include tests demonstrating: Fair utilization of available resources; Starvation prevention; Graceful degradation under overload conditions; and Resource usage. In general, the experiments do show that SFQ is better than FIFO queueing at allocating bandwidth equally among a set of flows. SFQ also prevents a stream from dominating the available bandwidth, which seems to be a tendency with FIFO queueing (i.e., if a flow demands more than its share of the available bandwidth, with FIFO queueing that stream receives a disproportionate amount when compared to flows demanding less than their share). Furthermore, SFQ seems to reward 'nice' users of the network by providing a lower variance in delay and more throughput when their resource demand is less than their available share. Both SFQ and FIFO queueing seem to degrade fairly well as the network becomes saturated and to recover well as the network becomes less congested. Not unexpectedly, FIFO queueing is a little more efficient than SFQ-the delays are less and the throughput slightly higher because SFQ requires more processing. However, the performance difference between the two queueing disciplines is relatively small. However, the experiments do point out some interesting behavior. FIFO queueing can behave better than SFQ with seed perturbation. We recommend further evaluation of the hash function and the seed perturbation technique. There are probably weaknesses in their current selection that cause this unexpected behavior. SFQ also seems to possess good scaling properties. To verify this, more experiments with a larger number of streams from more hosts need to be executed and examined, including the staggered introduction of streams. Staggering the streams may prove important, because graphs in the degradation experiment revealed some unexpected increases and decreases in throughput, which should be examined. This may again be due to the interaction of the hash function with the seed perturbation but it may also be related to some other unknown problem.

Denny, Barbara A.↗

Relating a Jet-Surface Interaction Experiment to a Commercial Supersonic Transport Aircraft Using Numerical Simulations

Reynolds-Averaged Navier-Stokes (RANS) simulations were performed for a commercial supersonic transport aircraft concept and experimental hardware models designed to represent the installed propulsion system of the conceptual aircraft in an upcoming test campaign. The purpose of the experiment is to determine the effects of jet-surface interactions from supersonic aircraft on airport community noise. RANS simulations of the commercial supersonic transport aircraft concept were performed to relate the representative experimental hardware to the actual aircraft. RANS screening simulations were performed on the proposed test hardware to verify that it would be free from potential rig noise and to predict the aerodynamic forces on the model hardware to assist with structural design. The simulations showed a large region of separated flow formed in a junction region of one of the experimental configurations. This was dissimilar with simulations of the aircraft and could invalidate the noise measurements. This configuration was modified and a subsequent RANS simulation showed that the size of the flow separation was greatly reduced. The aerodynamic forces found on the experimental models were found to be relatively small when compared to the expected loads from the model’s own weight.Reynolds-Averaged Navier-Stokes (RANS) simulations were completed for two configurations of a three-stream inverted velocity profile (IVP) nozzle and a baseline single-stream round nozzle (mixed-flow equivalent conditions). For the Sideline and Cutback flow conditions, while the IVP nozzles did not reduce the peak turbulent kinetic energy on the lower side of the jet plume, the IVP nozzles did significantly reduce the size of the region of peak turbulent kinetic energy when compared to the jet plume of the baseline nozzle cases. The IVP nozzle at Sideline conditions did suffer a region of separated flow from the inner stream nozzle splitter that did produce an intense, but small, region of turbulent kinetic energy in the vicinity of the nozzle exit. When viewed with the understanding that jet noise is directly related to turbulent kinetic energy, these IVP nozzle simulations show the potential to reduce noise to observers located below the nozzle. However, these RANS simulations also show that some modifications may be needed to prevent the small region of separated flow-induced turbulent kinetic energy from the inner stream nozzle splitter at Sideline conditions.

Reynolds-Averaged Navier Stokes↗

Capillary and acceleration wave breakup of liquid jets in axial-flow airstreams

Empirical correlations of reciprocal mean drop diameter with airstream momentum were derived from capillary and acceleration wave breakup of liquid jets atomized by cross stream injection into axial flow airstreams. A scanning radiometer was used to obtain data over an airstream momentum range of 3.7 to 25.7 g/sq cm sec. Transition from capillary to acceleration wave breakup was obtained at a critical Weber-Reynolds number of 1,000,000.

Ingebo, R. D.↗

Investigation of Spherical-Wave-Initiated Flow Fields Around Bodies

Measurements of the velocity flow fields and vortex movements have been made about various simple blunt models undergoing spherical blast waves with a positive overpressure of 4 pounds per square inch. A bullet-optical method was used to determine flow velocities and is applied to velocity fields in which the gradients are largely normal to the free-stream direction. The velocity flow fields are shown at various flow times following passage of the blast front for different models. Vortex movements with time are compared for square-bar models of various aspect ratios. Corner sharpness had no discernible effect on the overall disturbed velocity fields or vortex movements for the square-box models used.

McFarland, Donald R.↗

The heart works against gravity

The circulatory systems of vertebrate animals are closed, and blood leaves and returns to the heart at the same level. It is often concluded, therefore, that the heart works only against the viscous resistance of the system, not against gravity, even in vascular loops above the heart in which the siphon principle operates. However, we argue that the siphon principle does not assist blood flow in superior vascular loops if any of the descending vasculature is collapsible. If central arterial blood pressure is insufficient to support a blood column between the heart and the head, blood flow ceases because of vascular collapse. Furthermore, the siphon principle does not assist the heart even when a continuous stream of blood is flowing in a superior loop. The potential energy gained by blood as it is pumped to the head is lost to friction in partially collapsed descending vessels and thus is not regained. Application of the Poiseuille equation to flow in collapsible vessels is limited; resistance depends on flow rate in partially collapsed vessels with no transmural pressure difference, but flow rate is independent of resistance. Thus the pressure developed by the heart to establish a given flow rate is independent of the resistance occurring in the partially collapsed vessels. The pressure depends only on the height of the blood column and the resistance in the noncollapsed parts of the system. Simple laboratory models, involving water flow in collapsible tubing, dispel the idea that the siphon principle facilitates blood flow and suggest that previously published results may have been affected by experimental artifact.

Review, Tutorial↗

Scheduling Algorithm for Mission Planning and Logistics Evaluation (SAMPLE). Volume 1: User's guide

An interactive computer program for automatically generating traffic models for the Space Transportation System (STS) is presented. Information concerning run stream construction, input data, and output data is provided. The flow of the interactive data stream is described. Error messages are specified, along with suggestions for remedial action. In addition, formats and parameter definitions for the payload data set (payload model), feasible combination file, and traffic model are documented.

Dupnick, E.↗

Two-Equation Low-Reynolds-Number Turbulence Modeling of Transitional Boundary Layer Flows Characteristic of Gas Turbine Blades

The use of low Reynolds number (LRN) forms of the k-epsilon turbulence model in predicting transitional boundary layer flow characteristic of gas turbine blades is developed. The research presented consists of: (1) an evaluation of two existing models; (2) the development of a modification to current LRN models; and (3) the extensive testing of the proposed model against experimental data. The prediction characteristics and capabilities of the Jones-Launder (1972) and Lam-Bremhorst (1981) LRN k-epsilon models are evaluated with respect to the prediction of transition on flat plates. Next, the mechanism by which the models simulate transition is considered and the need for additional constraints is discussed. Finally, the transition predictions of a new model are compared with a wide range of different experiments, including transitional flows with free-stream turbulence under conditions of flat plate constant velocity, flat plate constant acceleration, flat plate but strongly variable acceleration, and flow around turbine blade test cascades. In general, calculational procedure yields good agreement with most of the experiments.

Schmidt, Rodney C.↗

Spectral solution of inviscid supersonic flows over wedges and axisymmetric cones

A shock-fitted multidomain spectral collocation method is used to solve both steady and unsteady inviscid supersonic flows over bodies. New aspects of the method include two subdomain interface types and a zonal solution procedure to get efficient convergence to steady-state in supersonic regions. Steady-state examples include flow over a sharp cone, a hyperbolic cone and a hyperbolic wedge. For the cone, the exact flow solution is used to show that the method is spectrally accurate. As an example of an unsteady flow, a calculation of the interaction of a free-stream hot ring with the flow over a sharp cone is presented.

Kopriva, David A.↗