Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Characterization of soil water content variability and soil texture using GPR groundwave techniques

Accurate characterization of near-surface soil water content is vital for guiding agricultural management decisions and for reducing the potential negative environmental impacts of agriculture. Characterizing the near-surface soil water content can be difficult, as this parameter is often both spatially and temporally variable, and obtaining sufficient measurements to describe the heterogeneity can be prohibitively expensive. Understanding the spatial correlation of near-surface soil water content can help optimize data acquisition and improve understanding of the processes controlling soil water content at the field scale. In this study, ground penetrating radar (GPR) methods were used to characterize the spatial correlation of water content in a three acre field as a function of sampling depth, season, vegetation, and soil texture. GPR data were acquired with 450 MHz and 900 MHz antennas, and measurements of the GPR groundwave were used to estimate soil water content at four different times. Additional water content estimates were obtained using time domain reflectometry measurements, and soil texture measurements were also acquired. Variograms were calculated for each set of measurements, and comparison of these variograms showed that the horizontal spatial correlation was greater for deeper water content measurements than for shallower measurements. Precipitation and irrigation were both shown to increase the spatial variability of water content, while shallowly-rooted vegetation decreased the variability. Comparison of the variograms of water content and soil texture showed that soil texture generally had greater small-scale spatial correlation than water content, and that the variability of water content in deeper soil layers was more closely correlated to soil texture than were shallower water content measurements. Lastly, cross-variograms of soil texture and water content were calculated, and co-kriging of water content estimates and soil texture measurements showed that geophysically-derived estimates of soil water content could be used to improve spatial estimation of soil texture.

54 ENVIRONMENTAL SCIENCES↗

Characterization of stearic acid adsorption on Ni(111) surface by experimental and first-principles study approach

Long-chain alkanoic acids usually form close-packed monolayer films with alkyl chains highly oriented on substrates. Previous studies have reported the adsorption of stearic acid on gold, aluminum, copper, silver, and aluminum oxide. However, there are no reports of stearic acid adsorption on magnetic metals. In this work, the characterization of stearic acid adsorbed on Ni(111) surface has been studied experimentally and with first-principles calculation. The results suggest that the stearic acid is chemically adsorbed on the Ni(111) surface via a bidentate interaction with a distance of about 1.8 A. Besides this, we have also obtained results for the charge transfer and magnetic proximity effect.

36 MATERIALS SCIENCE↗

Uranyl ion interaction at the water/NiO(100) interface: A predictive investigation by first-principles molecular dynamic simulations

The behavior of the UO{sub 2}{sup 2+} uranyl ion at the water/NiO(100) interface was investigated for the first time using Born-Oppenheimer molecular dynamic simulations with the spin polarized DFT +U extension. A water/NiO(100) interface model was first optimized on a defect-free five layers slab thickness, proposed as a reliable surface model, with an explicit treatment of the solvent. Water molecules are adsorbed with a well-defined structure in a thickness of about 4 A above the surface. The first layer, adsorbed on nickel atoms, remains mainly in molecular form but can partly dissociate at 293 K. Considering low acidic conditions, a bidentate uranyl ion complex was characterized on two surface oxygen species (arising from water molecules adsorption on nickel atoms) with d{sub U-O{sub a{sub d{sub s{sub o{sub r{sub p{sub t{sub i{sub o{sub n}}}}}}}}}}}=2.39 A. This complex is stable at 293 K due to iono-covalent bonds with an estimated charge transfer of 0.58 electron from the surface to the uranyl ion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Infrasound Generation from the HH Seismic Hammer.

The HH Seismic hammer is a large, "weight-drop" source for active source seismic experiments. This system provides a repetitive source that can be stacked for subsurface imaging and exploration studies. Although the seismic hammer was designed for seismological studies it was surmised that it might produce energy in the infrasonic frequency range due to the ground motion generated by the 13 metric ton drop mass. This study demonstrates that the seismic hammer generates a consistent acoustic source that could be used for in-situ sensor characterization, array evaluation and surface-air coupling studies for source characterization.

Jones, Kyle Richard↗

A Novel Mobile Examination and Remediation Facility for On-Site Remediation of Dry Storage Systems - 18389

Most of the spent nuclear fuel (SNF) in dry storage in the United States is safely and securely stored in dual-purpose (i.e., storage and transportation) canisters [1]. However, some of the SNF is stored in storage-only (i.e., non-transportable) packages, or packages that may become nonconforming for continued storage or transportation for a variety of reasons. Currently, the capability to remediate dry storage systems (DSSs) for SNF that are not transportable or that need to be repaired to maintain confinement boundary integrity during storage service does not exist without on-site access to a spent fuel pool. Hence, there is a potential future need for a mobile facility with remediation capabilities that can be used at multiple storage installations. These capabilities would permit needed repairs to an existing DSS to support continued storage or for the dry transfer of fuel to a new conveyance suitable for transport, if necessary. This is a technical paper that does not take into account the contractual limitations under the Standard Contract for Disposal of Spent Nuclear Fuel and/or High-Level Radioactive Waste (Standard Contract) (10 CFR Part 961). Under the provisions of the Standard Contract, DOE does not consider spent nuclear fuel in canisters to be an acceptable waste form, absent a mutually agreed to contract amendment. To the extent discussions or recommendations in this paper conflict with the provisions of the Standard Contract, the Standard Contract provisions prevail. A novel design concept for a Mobile Examination and Remediation Facility (MERF) is proposed with functions and capabilities to remediate a DSS. The proposed MERF would be a multi-purpose facility, remotely operated and computer-controlled with semi-automated equipment to allow trained operators to safely perform remediation activities while keeping worker radiation dose as low as reasonably achievable. It would include a shielded rotating platform with support towers and would use commercial off- the-shelf examination and repair equipment. A slip ring arrangement underneath the rotating platform would allow for the power supply without impeding the continuous rotation and would simplify cable management. The support towers would be mounted on the rotating platform, and each tower would have vertical and horizontal positioning capability for axial and radial tool location. The rotating platform would be attached to the main MERF structure. Capabilities would include visual, surface, and volumetric examinations to fully characterize physical conditions on canister surface before and after a repair; repair techniques, e.g., laser beam welding, friction stir welding, or cold spray, to perform needed remediation activities; and associated equipment for surface preparation such as cutting and grinding equipment. The proposed design would be simple, modular, robust, economically viable, and easily transportable and would have a small footprint. The modular design would present several advantages including compatibility with a variety of different DSSs, on-site assembly, and transportability; it also would be built in interchangeable sections to facilitate decontamination. Further, shielding would be supplemented through interface with the existing transfer cask and storage overpack. Robustness and canister stability would be achieved using pneumatic holders and steel support structures designed with vibration absorbers to reduce impacts and/or a 'pendulum' effect during a seismic event. Thus, the proposed MERF would be designed to: (i) minimize handling of an affected DSS to the extent practicable, (ii) provide radiation shielding and minimize dose to operators and the public during remediation activities, and (iii) enable examination, repair, and repackaging. This paper describes the proposed MERF design concept and capabilities, main components, equipment, different modes of operation, and operating procedures. Structural and safety assessments would need to be performed before final design, licensing, and deployment. The MERF is evaluated with respect to regulatory impact (first of a kind, prior experience), operational impact (safety, security, staffing, ongoing operations, constraints), worker dose (low, medium, high), cost (low, medium, high), schedule (duration, time sequence), and technology readiness level. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Tailoring the Surface of Metal Halide Perovskites to Enable the Atomic Layer Deposition of Metal Oxide Contacts

Replacing organic contact layers with inorganic counterparts, such as metal oxides, is one strategy for improving long-term device stability in metal halide perovskite solar cells. Often, the methods used to deposit metal oxide thin films are incompatible with metal halide perovskites, creating challenges for the fabrication of contacts above the perovskite absorber layer. In this study, we utilize a one-step, solution treatment of the top surface of Cs 0.25 FA 0.75 Pb(Br 0.20 I 0.80 ) 3 to create a thin (~1 nm) overlayer of lead sulfide (PbS) to protect the underlying perovskite during subsequent deposition. X-ray characterization of the surface region shows that the PbS overlayer limits undesirable changes to the perovskite structure and stoichiometry during atomic layer deposition (ALD) of SnO 2 . This protection enables ALD growth of SnO 2 electron contacts on top of the perovskite without an organic transport layer (e.g., C 60 ), resulting in a solar cell with a power conversion efficiency of 5.8%. This result is a marked improvement over devices with ALD SnO 2 grown directly on the perovskite without a PbS overlayer, which produce no power output. Furthermore, the interface characterization and device results in this study highlight some of the key challenges associated with ALD metal oxide growth on perovskite materials and can help inform the future design of inorganic contact layer deposition in solar photovoltaic technologies.

36 MATERIALS SCIENCE↗

Dynamic Defrosting on Scalable Superhydrophobic Surfaces

Recent studies have shown that frost can grow in a suspended Cassie state on nanostructured superhydrophobic surfaces. During defrosting, the melting sheet of Cassie frost spontaneously dewets into quasi-spherical slush droplets that are highly mobile. Promoting Cassie frost would therefore seem advantageous from a defrosting standpoint; however, nobody has systematically compared the efficiency of defrosting Cassie ice versus defrosting conventional surfaces. Here, we characterize the defrosting of an aluminum plate, one-half of which exhibits a superhydrophobic nanostructure while the other half is smooth and hydrophobic. For thick frost sheets (>1 mm), the superhydrophobic surface was able to dynamically shed the meltwater, even at very low tilt angles. In contrast, the hydrophobic surface was unable to shed any appreciable meltwater even at a 90° tilt angle. For thin frost layers (≲1 mm), not even the superhydrophobic surface could mobilize the meltwater. We attribute this to the large apparent contact angle of the meltwater, which for small amounts of frost serves to minimize coalescence events and prevent droplets from approaching the capillary length. Finally, we demonstrate a new mode of dynamic defrosting using an upside-down surface orientation, where the melting frost was able to uniformly detach from the superhydrophobic side and subsequently pull the frost from the hydrophobic side in a chain reaction. Treating surfaces to enable Cassie frost is therefore very desirable for enabling rapid and low-energy thermal defrosting, but only for frost sheets that are sufficiently thick.

36 MATERIALS SCIENCE↗

Structure of Biodegradable Films at Aqueous Surfaces: X-ray Diffraction and Spectroscopy Studies of Polylactides and Tyrosine-Derived Polycarbonates

Three representative polymers of increasing modulus, poly(d,l-lactic acid), PDLLA, poly(desaminotyrosyl-tyrosine ethyl ester carbonate), PDTEC, and the same polymer with iodinated DTE segments, PI2DTEC, were characterized by surface-pressure versus area (Π–A) isotherms and surface sensitive X-ray diffraction techniques. Films of 10–100 Å thickness were prepared for these studies by spreading dilute polymer solutions at air–water interfaces. The general properties of the isotherms and the Flory exponents, determined from the isotherms, vary in accordance with the increasing modulus of PDLLA, PDTEC, PI2DTEC, respectively. The analysis of in situ X-ray reflectivity and grazing incidence X-ray diffraction (GIXD) measurements from films at aqueous surfaces provides a morphological picture that is consistent with the modulus of the polymers, and to a large extent, with their packing in their dry-bulk state. Large absorption of X-rays by iodine enabled X-ray spectroscopic studies under near-total-reflection conditions to determine the iodine distribution in the PI2DTEC film and complement the structural model derived from reflectivity and GIXD. These structural studies lay the foundation for future studies of polymer–protein interactions at aqueous interfaces.

36 MATERIALS SCIENCE↗

Characterization of electron-beam recorded microdomain patterns on the nonpolar surface of LiNbO{sub 3} crystal by nondestructive methods

We report on characterization of the electron-beam fabricated planar domain gratings on the nonpolar (Y-) surface of LiNbO{sub 3} crystals performed with the use of AFM and confocal second harmonic generation (SHG) microscopy. The dependence of domain formation on the irradiation conditions was investigated. The relation of domain thicknesses to the electron penetration depth is experimentally proved. In particular, the possibility of controlling the thickness of planar domains by varying acceleration electron-beam voltages is demonstrated. The observed specificity of SHG is analyzed in the framework of the Kleinman-Boyd theory [G. D. Boyd and D. A. Kleinman, J. Appl. Phys. 39, 3597 (1968)] and Uesu approach [Kaneshiro et al., J. Appl. Phys. 104, 054112 (2008); Kaneshiro et al., J. Opt. Soc. Am. B 27, 888 (2010)] extended in our case to reflection geometry. The calculations performed predict the dependence of SHG conversion efficiency η on the domain thickness, which is in a qualitative agreement with the experiment. It is shown that planar domains on top of the nonpolar surface always enhance the value of η as compared with the bare surface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigation of Microscopic Materials Limitations of Superconducting RF Cavities

The high-field performance of SRF cavities is often limited by breakdown events below the intrinsic limiting surface fields of Nb, and there is abundant evidence that these breakdown events are localized in space inside the cavity. Also, there is a lack of detailed understanding of the causal links between surface treatments and ultimate RF performance at low temperatures. An understanding of these links would provide a clear roadmap for improvement of SRF cavity performance, and establish a cause-and-effect ‘RF materials science’ of Nb. We propose two specific microscopic approaches to addressing these issues. First is a spatially-resolved local microwave-microscope probe that operates at SRF frequencies and temperatures to discover the microscopic origins of breakdown, and produce quantitative measurements of RF critical fields of coatings and films. Second, RF Laser Scanning Microscopy (LSM) has allowed visualization of RF current flow and sources of nonlinear RF response in superconducting devices with micro-meter spatial resolution. The LSM will be used in conjunction with surface preparation and characterization techniques to create definitive links between physical and chemical processing steps and ultimate cryogenic microwave performance. We propose to develop RF laser scanning microscopy of small-sample Nb pieces to establish surface-processing / RF performance relations through measurement of RF current distributions on micron-length scales and low temperatures.

36 MATERIALS SCIENCE↗

Laser Welding-Brazing of Immiscible AZ31B Mg and Ti-6Al-4V Alloys Using an Electrodeposited Cu Interlayer

Metallurgical bonding between immiscible system AZ31B magnesium (Mg) and Ti-6Al-4V titanium (Ti) was achieved by adding Cu interlayer using laser welding-brazing process. Effect of the laser power on microstructure evolution and mechanical properties of Mg/Cu-coated Ti joints was studied. Visually acceptable joints were obtained at the range of 1300 to 1500 W. The brazed interface was divided into three parts due to temperature gradient: direct irradiation zone, intermediate zone and seam head zone. Ti{sub 3}Al phase was produced along the interface at the direct irradiation zone. Ti-Al reaction layer grew slightly with the increase in laser power. A small amount of Ti{sub 2}(Cu,Al) interfacial compounds formed at the intermediate zone and the (α-Mg + Mg{sub 2}Cu) eutectic structure dispersed in the fusion zone instead of gathering when increasing the laser power at this zone. At the seam head zone, Mg-Cu eutectic structure was produced in large quantities under all cases. Joint strength first increased and then decreased with the variation of the laser power. The maximum fracture load of Mg/Cu-coated Ti joint reached 2314 N at the laser power of 1300 W, representing 85.7% joint efficiency when compared with Mg base metal. All specimens fractured at the interface. The feature of fracture surface at the laser power of 1100 W was characterized by overall smooth surface. Obvious tear ridge and Ti{sub 3}Al particles were observed at the fracture surface with increase in laser power. It suggested atomic diffusion was accelerated with more heat input giving rise to the enhanced interfacial reaction and metallurgical bonding in direct irradiation zone, which determined the mechanical properties of the joint.

36 MATERIALS SCIENCE↗

Effect of aqueous-based mechanical polishing on the nanoindentation response of borosilicate glasses

When attempting to measure material properties by sampling near-surface volumes with techniques like nanoindentation, careful consideration of the state of the surface compared to the bulk is paramount for valid characterization. The process of surface planarization of glass in preparation for analysis is no exception. Water's general reactivity with silicate glasses has been well-established, but under the typical conditions for mechanical polishing, the usual practical assumption is that the potential effects on measured mechanical properties are insignificant due to the short period of glass-water interaction and the non-extreme corrosive environment. However, in this research, it is shown that the act of polishing certain borosilicate glass compositions in an aqueous environment directly affects the nanomechanical response to several micrometers, reducing the measured elastic modulus and hardness by ~20% and ~35%, respectively. Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) are used to confirm the formation of an altered, hydrated surface layer.

36 MATERIALS SCIENCE↗

Surface Water Disinfection Byproducts and Organic Matter Characterization Data Associated with: “Disinfection byproducts formed during drinking water treatment reveal an export control point for dissolved organic matter in a subalpine headwater stream”

This dataset is associated with the publication “Disinfection byproducts formed during drinking water treatment reveal an export control point for dissolved organic matter in a subalpine headwater stream” published in Water Research X (Leonard et al. 2022; https://doi.org/10.1016/j.wroa.2022.100144). The associated study analyzed temporal trends from the Town of Crested Butte water treatment facility and synoptic sampling at Coal Creek in Crested Butte, Colorado, US. This work demonstrates how drinking water quality archives combined with synoptic sampling and targeted analyses can be used to identify and understand export control points for dissolved organic matter. This dataset is comprised of one main data folder containing (1) file-level metadata; (2) data dictionary; (3) metadata and international geo-sample number (IGSN) mapping file; (4) dissolved organic carbon (DOC), ultraviolet absorbance at 254 nanometers (UV254), total nitrogen (TN), and specific ultraviolet absorbance (SUVA) data; (5) disinfection bioproduct formation potential (DBP-FP) data; (6) readme; (7) methods codes; (8) water collection protocol; (9) folder of high resolution characterization of organic matter via 12 Tesla Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) through the Environmental Molecular Sciences Laboratory (EMSL; https://www.pnnl.gov/environmental-molecular-sciences-laboratory); and (10) folder of excitation emissions matrix (EEM) spectra. The FTICR folder contains a file of DOC (measured as non-purgeable organic carbon; NPOC) used for FTICR sample preparation. The FTICR folder also contains three subfolders: one subfolder containing the raw .xml data files, one containing the processed data, and the other containing instructions for using Formularity (https://omics.pnl.gov/software/formularity) and an R script to process the data based on the user's specific needs. All files are .csv, .pdf, .dat, .R, .ref, or .xml

54 ENVIRONMENTAL SCIENCES↗

Humidity-dependent compression-induced glass transition of the air–water interfacial Langmuir films of poly(D,L-lactic acid- ran -glycolic acid) (PLGA)

Constant rate compression isotherms of the air–water interfacial Langmuir films of poly(D,L-lactic acid- ran -glycolic acid) (PLGA)show a distinct feature of an exponential increase in surface pressure in the high surface polymer concentration regime. We have previously demonstrated that this abrupt increase in surface pressure is linked to the glass transition of the polymer film, but the detailed mechanism of this process is not understood. In order to obtain a molecular-level understanding of this behavior, we performed extensive characterizations of the surface mechanical, structural and rheological properties of Langmuir PLGA films at the air–water interface, using combined experimental techniques including the Langmuir film balance, X-ray reflectivity and double-wall-ring interfacial rheometry methods.

36 MATERIALS SCIENCE↗

Infrared thermometry and interferential microscopy for analysis of crater formation at the surface of fused silica under CO{sub 2} laser irradiation

In situ spatial and temporal temperature measurements of a fused silica surface heated by a 10.6 {mu}m CO{sub 2} laser were performed using an infrared camera. These measurements were derived from heat flux emission of the fused silica. High temperature measurements--in the range 400-2500 K--were performed at the surface of a semi-transparent media with a high spatial resolution. Particular attention was given to the experimental conception and to the calibration of the infrared device. Moreover, both conventional and interferential microscopes were used to characterize the silica surfaces after CO{sub 2} laser irradiation. By associating these results with thermal camera measurements we identified the major surface temperature levels of silica transformation when heated during 250 ms. Surface deformation of silica is observed for temperatures <2000 K. This is consistent with other recent work using CO{sub 2} laser heating. At higher temperatures, matter ejection, as deduced from microscope observations, occurs at temperatures that are still much lower than the standard boiling point. Such evaporation is described by a thermodynamical approach, and calculations show very good agreement with experiment.

36 MATERIALS SCIENCE↗

Enhanced photoelectrochemical water splitting from Si quantum dots/TiO{sub 2} nanotube arrays composite electrodes

Graphical abstract: Si quantum dots were firstly applied to modify TiO{sub 2} nanotubes and enhanced visible light response was demonstrated for the resulted Si QDs/TiO{sub 2} nanocomposite. Si QDs are promising in photoelectrochemical water splitting and photocatalysis since their low cost, abundance and environmentally-friendliness. - Highlights: • A novel nanocomposite Si QDs/TiO{sub 2} nanotubes was fabricated and characterized. • Enhanced photoelectrochemical water splitting was firstly demonstrated for Si QDs/TiO{sub 2}. • The visible light response of TiO{sub 2} increased with the presence of Si QDs. - Abstract: This work firstly introduced Si quantum dots (QDs) to modify TiO{sub 2} nanotube arrays for photoelectrochemical water splitting. A systematic study using surface and optical characterization tools reveals the nature of the combination of Si QDs and TiO{sub 2} nanotube arrays. Scanning electron microscopy and X-ray photoelectron spectroscopy results show that Si QDs were assembled on the surface of vertically aligned TiO{sub 2} nanotube arrays. The UV–vis diffuse reflectance spectra indicate the improved visible light absorbance. The enhanced photoelectrochemical water splitting was demonstrated under visible light illumination and the photocurrent density was 1.6 times larger than that of pristine TiO{sub 2} electrodes. Electrochemical impedance behavior was measured for the electrodes and the impedance is slightly reduced for the nanocomposite electrode with the presence of Si QDs. This work demonstrated that Si QDs would be a novel and effective choice for improving the utilization of visible light for TiO{sub 2} nanotubes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effects of Solution Chemistry on the Dechlorination of 1,2,3-Trichloropropane by Zero-Valent Zinc

The reactivity of zerovalent zinc (ZVZ) toward 1,2,3-trichloropropane (TCP) was evaluated under a variety of solution conditions, including deionized water, groundwater, and artificial groundwater, over a pH range of about 6.5-12. In deionized water, first-order rate constants for TCP disappearance (kobs) exhibit a broad minimum between pH 8 and 10, with increasing kobs observed at lower and higher pH. The similarity between this trend and zinc oxide (ZnO) solubility behavior suggests pH related changes to the ZnO surface layer strongly influence ZVZ reactivity. Values of kobs measured in acidic groundwater are similar to those measured in DI water, whereas values measured in alkaline groundwater are much smaller (>1 order of magnitude at pH values >10). Characterization of the surfaces of ZVZ exposed to deionized water, acidic groundwater, and alkaline groundwater suggests that the slower rates obtained in alkaline groundwater are related to the presence of a morphologically distinct surface film that passivates the ZVZ surface. TCP degradation rates in artificial groundwater containing individual solutes present in groundwater suggest that silicate anions contribute to the formation of this passivating film.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Monovalent and Divalent Cations at the a-Al2O3(0001)/Water Interface: How Cation Identity Affects Interfacial Ordering and Vibrational Dynamics

Mineral oxide-water interfaces are important for a wide range of industrial, geochemical, and biological processes. The reactivity of these interfaces is strongly impacted by the presence of ions. Thus, it is critical to understand how ions alter the interfacial environment. This can be achieved by measuring the changes in the structure and vibrational dynamics of interfacial water induced by the presence of ions in close vicinity to the mineral surface. The a-Al2O3(0001) surface represents a flexible platform to study the effect of ions on interfacial aqueous environments at positive, neutral and negative surface charge. Using vibrational sum frequency generation (vSFG) in the frequency and time domain, we investigate how monovalent and divalent cations affect the hydrogen bonding environment of the first few layers of interfacial water next to a-Al2O3(0001). Our results indicate that monovalent cations, such as Li+, Na+, K+, and Cs+, appear to have lower binding affinities for the interface compared to Ca2+, Sr2+, and Ba2+. This leads to an interfacial region that is structured in a cation valence dependent manner. Addition of divalent cations at the negatively charged interface (pH 10) increases the spectral intensity in the 3400 cm-1 region compared to neat pH 10 H2O, in contrast to monovalent cations that only attenuate the vSFG signal. Time resolved vSFG measurements reveal that the O-H vibrational lifetime (T1) of interfacial species at pH 10 in the presence of NaCl and BaCl2 remains similar, but restructuring of the surface seen in steady state vSFG is manifested in the degree to which strongly hydrogen bonded species recover to their original populations post excitation. By tracking the accumulation of ions at the interface via the vSFG response, we can characterize the unique surface arrangements of interfacial water molecules induced by a range of monovalent and divalent cations at the a-Al2O3(0001)/water interface.

Piontek, Stefan↗