Search NASA⌕ Search

SEARCH · Search NASA

Results for “variational optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Simulation Model of Microsphere Distribution for Selective Internal Radiation Therapy Agrees With Observations

Purpose: To perform a detailed analysis of microsphere distribution in biopsy material from a patient treated with {sup 90}Y-labeled resin spheres and characterize microsphere distribution in the hepatic artery tree, and to construct a novel dichotomous bifurcation model for microsphere deposits and evaluate its accuracy in simulating the observed microsphere deposits. Methods and Materials: Our virtual model consisted of arteries that successively branched into 2 new generations of arteries at 20 nodes. The artery diameter exponentially decreased from the lowest generation to the highest generation. Three variable parameters were optimized to obtain concordance between simulations and measure microsphere distributions: an artery coefficient of variation (ACV) for the diameter of all artery generations and the microsphere flow distribution at the nodes; a hepatic tree distribution volume (HDV) for the artery tree; and an artery diameter reduction (ADR) parameter. The model was tested against previously measured activity concentrations in 84 biopsies from the liver of 1 patient. In 16 of 84 biopsies, the microsphere distribution regarding cluster size and localization in the artery tree was determined via light microscopy of 30-μm sections (mean concentration, 14 microspheres/mg; distributions divided into 3 groups with mean microsphere concentrations of 4.6, 14, and 28 microspheres/mg). Results: Single spheres and small clusters were observed in terminal arterioles, whereas large clusters, up to 450 microspheres, were observed in larger arterioles. For 14 microspheres/mg, the optimized parameter values were ACV=0.35, HDV = 50 cm{sup 3}, and ADR=6 μm. For 4.6 microspheres/mg, ACV and ADR decreased to 0.26 and 0 μm, respectively, whereas HDV increased to 130 cm{sup 3}. The opposite trend was observed for 28 microspheres/mg: ACV = 0.49, HDV = 20 cm{sup 3}, and ADR = 8 μm. Conclusion: Simulations and measurements reveal that microsphere clusters are larger and more common in volumes with high microsphere concentrations and indicate that the spatial distribution of the artery tree must be considered in estimates of microsphere distributions.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Phase retrieval of diffraction from highly strained crystals

An important application of phase retrieval methods is to invert coherent x-ray diffraction measurements to obtain real-space images of nanoscale crystals. The phase information is currently recovered from reciprocal-space amplitude measurements by the application of iterative projective algorithms that solve the nonlinear and nonconvex optimization problem. Various algorithms have been developed each of which apply constraints in real and reciprocal space on the reconstructed object. In general, these methods rely on experimental data that is oversampled above the Nyquist frequency. To date, support-based methods have worked well, but are less successful for highly strained structures, defined as those which contain (real-space) phase information outside the range of {+-}{pi}/2. As a direct result the acquired experimental data is, in general, inadvertently subsampled below the Nyquist frequency. In recent years, a new theory of 'compressive sensing' has emerged, which dictates that an appropriately subsampled (or compressed) signal can be recovered exactly through iterative reconstruction and various routes to minimizing the l{sub 1} norm or total variation in that signal. This has proven effective in solving several classes of convex optimization problems. Here we report on a 'density-modification' phase reconstruction algorithm that applies the principles of compressive sensing to solve the nonconvex phase retrieval problem for highly strained crystalline materials. The application of a nonlinear operator in real-space minimizes the l{sub 1} norm of the amplitude by a promotion-penalization (or 'propenal') operation that confines the density bandwidth. This was found to significantly aid in the reconstruction of highly strained nanocrystals. We show how this method is able to successfully reconstruct phase information that otherwise could not be recovered.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Importance of incorporating spatial and temporal variability of biomass yield and quality in bioenergy supply chain

Abstract Biofuels made from biomass and waste residues will largely contribute to United States’ 2050 decarbonization goal in the aviation sector. While cellulosic biofuels have the potential fuel performance equivalent to petroleum-based jet fuel, the biofuel industry needs to overcome the supply chain barrier caused by temporal and spatial variability of biomass yield and quality. This study highlights the importance of incorporating spatial and temporal variability during biomass supply chain planning via optimization modeling that incorporates 10 years of drought index data, a primary factor contributing to yield and quality variability. The results imply that the cost of delivering biomass to biorefinery may be significantly underestimated if the multi-year temporal and spatial variation in biomass yield and quality is not captured. For long term sustainable biorefinery operations, the industry should optimize supply chain strategy by studying the variability of yield and quality of biomass in their supply sheds.

09 BIOMASS FUELS↗

Optimization of radar imaging system parameters for geological analysis

The use of radar image simulation to model terrain variation and determine optimum sensor parameters for geological analysis is described. Optimum incidence angle is determined by the simulation, which evaluates separately the discrimination of surface features possible due to terrain geometry and that due to terrain scattering. Depending on the relative relief, slope, and scattering cross section, optimum incidence angle may vary from 20 to 80 degrees. Large incident angle imagery (more than 60 deg) is best for the widest range of geological applications, but in many cases these large angles cannot be achieved by satellite systems. Low relief regions require low incidence angles (less than 30 deg), so a satellite system serving a broad range of applications should have at least two selectable angles of incidence.

Waite, W. P.↗

Computer-oriented synthesis of wide-band non-uniform negative resistance amplifiers

This paper presents a synthesis procedure which provides design values for broad-band amplifiers using non-uniform negative resistance devices. Employing a weighted least squares optimization scheme, the technique, based on an extension of procedures for uniform negative resistance devices, is capable of providing designs for a variety of matching network topologies. It also provides, for the first time, quantitative results for predicting the effects of parameter element variations on overall amplifier performance. The technique is also unique in that it employs exact partial derivatives for optimization and sensitivity computation. In comparison with conventional procedures, significantly improved broad-band designs are shown to result.

Branner, G. R.↗

Space Shuttle Main Engine performance analysis

For a number of years, NASA has relied primarily upon periodically updated versions of Rocketdyne's power balance model (PBM) to provide space shuttle main engine (SSME) steady-state performance prediction. A recent computational study indicated that PBM predictions do not satisfy fundamental energy conservation principles. More recently, SSME test results provided by the Technology Test Bed (TTB) program have indicated significant discrepancies between PBM flow and temperature predictions and TTB observations. Results of these investigations have diminished confidence in the predictions provided by PBM, and motivated the development of new computational tools for supporting SSME performance analysis. A multivariate least squares regression algorithm was developed and implemented during this effort in order to efficiently characterize TTB data. This procedure, called the 'gains model,' was used to approximate the variation of SSME performance parameters such as flow rate, pressure, temperature, speed, and assorted hardware characteristics in terms of six assumed independent influences. These six influences were engine power level, mixture ratio, fuel inlet pressure and temperature, and oxidizer inlet pressure and temperature. A BFGS optimization algorithm provided the base procedure for determining regression coefficients for both linear and full quadratic approximations of parameter variation. Statistical information relative to data deviation from regression derived relations was also computed. A new strategy for integrating test data with theoretical performance prediction was also investigated. The current integration procedure employed by PBM treats test data as pristine and adjusts hardware characteristics in a heuristic manner to achieve engine balance. Within PBM, this integration procedure is called 'data reduction.' By contrast, the new data integration procedure, termed 'reconciliation,' uses mathematical optimization techniques, and requires both measurement and balance uncertainty estimates. The reconciler attempts to select operational parameters that minimize the difference between theoretical prediction and observation. Selected values are further constrained to fall within measurement uncertainty limits and to satisfy fundamental physical relations (mass conservation, energy conservation, pressure drop relations, etc.) within uncertainty estimates for all SSME subsystems. The parameter selection problem described above is a traditional nonlinear programming problem. The reconciler employs a mixed penalty method to determine optimum values of SSME operating parameters associated with this problem formulation.

Santi, L. Michael↗

Modular Design of Advanced Catalytic Materials Using Hybrid Organic-Inorganic Raspberry Particles

Catalysis is one of the most sophisticated areas of materials research that encompasses a diverse set of materials and phenomena occurring on multiple length and time scales. Designing catalysts that can be broadly applied toward global energy and environmental challenges requires the development of universal frameworks for complex catalytic systems through rational and independent (or quasi-independent) optimization of multiple structural and compositional features. Toward addressing this goal, a modular platform is presented in which sacrificial organic colloids bearing catalytic nanoparticles on their surfaces self-assemble with matrix precursors, simultaneously structuring the resulting porous networks and fine-tuning the locations of catalyst particles. This strategy allows combinatorial variations of the material building blocks and their organization, in turn providing numerous degrees of freedom for optimizing the material's functional properties, from the nanoscale to the macroscale. The platform enables systematic studies and rational design of efficient and robust systems for a wide range of catalytic and photocatalytic reactions, as well as their integration into industrial and other real-life environments.

36 MATERIALS SCIENCE↗

A surface work function measurement technique utilizing constant deflected grazing electron trajectories: Oxygen uptake on Cu(001)

We report on the application of a novel nondestructive in-vacuum technique for relative work function measurements, employing a grazing incidence electron deflection above a sample with a planar surface. Two deflected electron beam detectors are used as a position sensitive detector to control feedback to the sample potential as the sample work function changes. With feedback the sample potential exactly follows the surface sample-size averaged work function variation, so that the deflected beam trajectory remains stable. We also discuss methods to optimize the initial electron trajectories for this method, so as to minimize unwanted effects such as from uncontrolled external magnetic fields. As the electron beam does not impinge on the surface in this new technique electron induced desorption, ionization, dissociation, and/or decomposition is not induced at the interface. Importantly also the technique allows for free access to the surfaces enabling simultaneous deposition/evaporation and/or application of other surface characterization methods. We demonstrate its application in concurrent measurements of helium atom reflectivity and work function changes taking place during molecular oxygen exposure of a Cu(001) surface. A work function measurement sensitivity and stability is demonstrated at {approx}10 mV at a sampling rate of 1 Hz and after application of an {approx}7 s smoothing routine. In comparison to the helium atom reflectivity measurements, the work function measurements are more sensitive to the initial O uptake, and less so to the final coverage variations and possible surface reordering at higher O coverages.

43 PARTICLE ACCELERATORS↗

Development of Training Programs to Optimize Planetary Ambulation

Astronauts experience disturbances in functional mobility following their return to Earth due to adaptive responses that occur during exposure to the microgravity conditions of space flight. Despite significant time spent performing in-flight exercise routines, these training programs have not been able to mitigate postflight alterations in postural and locomotor function. Therefore, the goal of our two inter-related projects (NSBRI-ground based and ISS flight study, "Mobility") is to develop and test gait training programs that will serve to optimize functional mobility during the adaptation period immediately following space flight, thereby improving the safety and efficiency of planetary ambulation. The gait training program entails manipulating the sensory conditions of treadmill exercise to systematically challenge the balance and gait control system. This enhances the overall adaptability of locomotor function enabling rapid reorganization of gait control to respond to ambulation in different gravitational environments. To develop the training program, we are conducting a series of ground-based studies evaluating the training efficacy associated with variation in visual flow, body loading, and support surface stability during treadmill walking. We will also determine the optimal method to present training stimuli within and across training sessions to maximize both the efficacy and efficiency of the training procedure. Results indicate that variations in both visual flow and body unloading during treadmill walking leads to modification in locomotor control and can be used as effective training modalities. Additionally, the composition and timing of sensory challenges experienced during each training session has significant impact on the ability to rapidly reorganize locomotor function when exposed to a novel sensory environment. We have developed the capability of producing support surface variation during gait training by mounting a treadmill on a six-degree-of-freedom motion device. This hardware development will allow us to evaluate the efficacy of this type of training in conjunction with variation in visual flow and body unloading.

Bloomberg, J. J.↗

Optimal Area Profiles for Ideal Single Nozzle Air-Breathing Pulse Detonation Engines

The effects of cross-sectional area variation on idealized Pulse Detonation Engine performance are examined numerically. A quasi-one-dimensional, reacting, numerical code is used as the kernel of an algorithm that iteratively determines the correct sequencing of inlet air, inlet fuel, detonation initiation, and cycle time to achieve a limit cycle with specified fuel fraction, and volumetric purge fraction. The algorithm is exercised on a tube with a cross sectional area profile containing two degrees of freedom: overall exit-to-inlet area ratio, and the distance along the tube at which continuous transition from inlet to exit area begins. These two parameters are varied over three flight conditions (defined by inlet total temperature, inlet total pressure and ambient static pressure) and the performance is compared to a straight tube. It is shown that compared to straight tubes, increases of 20 to 35 percent in specific impulse and specific thrust are obtained with tubes of relatively modest area change. The iterative algorithm is described, and its limitations are noted and discussed. Optimized results are presented showing performance measurements, wave diagrams, and area profiles. Suggestions for future investigation are also discussed.

Paxson, Daniel E.↗

Issues and Strategies in Solving Multidisciplinary Optimization Problems

Optimization research at NASA Glenn Research Center has addressed the design of structures, aircraft and airbreathing propulsion engines. The accumulated multidisciplinary design activity is collected under a testbed entitled COMETBOARDS. Several issues were encountered during the solution of the problems. Four issues and the strategies adapted for their resolution are discussed. This is followed by a discussion on analytical methods that is limited to structural design application. An optimization process can lead to an inefficient local solution. This deficiency was encountered during design of an engine component. The limitation was overcome through an augmentation of animation into optimization. Optimum solutions obtained were infeasible for aircraft and airbreathing propulsion engine problems. Alleviation of this deficiency required a cascading of multiple algorithms. Profile optimization of a beam produced an irregular shape. Engineering intuition restored the regular shape for the beam. The solution obtained for a cylindrical shell by a subproblem strategy converged to a design that can be difficult to manufacture. Resolution of this issue remains a challenge. The issues and resolutions are illustrated through a set of problems: Design of an engine component, Synthesis of a subsonic aircraft, Operation optimization of a supersonic engine, Design of a wave-rotor-topping device, Profile optimization of a cantilever beam, and Design of a cylindrical shell. This chapter provides a cursory account of the issues. Cited references provide detailed discussion on the topics. Design of a structure can also be generated by traditional method and the stochastic design concept. Merits and limitations of the three methods (traditional method, optimization method and stochastic concept) are illustrated. In the traditional method, the constraints are manipulated to obtain the design and weight is back calculated. In design optimization, the weight of a structure becomes the merit function with constraints imposed on failure modes and an optimization algorithm is used to generate the solution. Stochastic design concept accounts for uncertainties in loads, material properties, and other parameters and solution is obtained by solving a design optimization problem for a specified reliability. Acceptable solutions can be produced by all the three methods. The variation in the weight calculated by the methods was found to be modest. Some variation was noticed in designs calculated by the methods. The variation may be attributed to structural indeterminacy. It is prudent to develop design by all three methods prior to its fabrication. The traditional design method can be improved when the simplified sensitivities of the behavior constraint is used. Such sensitivity can reduce design calculations and may have a potential to unify the traditional and optimization methods. Weight versus reliability traced out an inverted-S-shaped graph. The center of the graph corresponded to mean valued design. A heavy design with weight approaching infinity could be produced for a near-zero rate of failure. Weight can be reduced to a small value for a most failure-prone design. Probabilistic modeling of load and material properties remained a challenge.

Patnaik, Surya↗

A Hardware and Software Co-design Framework for Energy Efficient Neuromorphic Systems

Neuromorphic systems can be realized by a variety of algorithms and architectures. A common understanding is that spiking neuromorphic designs, which encode information into spatio-temporal spiking events, are both a biologically-accurate and efficient way of processing information. However, representing the information through timing relationships induces sophisticated circuit designs in traditional CMOS-based implementations. In recent years, high-capacity resistive memory (RRAM, aka, memristor) has demonstrated great potential in mimicking synaptic behaviors. Several RRAM-based spiking neuromorphic designs exist, most of which focus on rate coding schemes. These designs simplify circuit implementations of neuron models and explore challenges such as unsatisfactory speed, resolution, and performance. As an alternative, we will explore temporal coding spiking neuromorphic systems that encode information as the relative timing of neuron activations (spikes), which have been proven to be more adaptive and energy-efficient. Developing a neuromorphic system for spiking neural network (SNN) inference and online training, however, faces some major technical challenges: (1) It lacks circuit implementation support for temporal-coding SNN to achieve satisfying power efficiency and accuracy; (2) Although existing research works have investigated memristive synapse and neuron designs for spike-timing-dependent plasticity, the non-ideal conditions in implementation, such as device variations and signal degradation, degrade online learning accuracy of large scale systems; and (3) Non-optimized, inter-layer data traffic in SNNs, leads to unnecessary data communication costs. In this project, we plan to address these challenges by a hardware and software co-design framework that incorporates solutions at the circuit, architecture, and algorithm levels. At the circuit-level, we will elaborate on the in-situ SNN processing element designs for supporting both inference and online training modes. Variation-aware schemes will be studied to improve reliability. At the architecture level, we propose a pipelined, asynchronous architecture to retain the timing resolution of spikes. At the algorithm level, we will investigate an innovative SNN training algorithm for enabling activation sparsification and reducing unnecessary data communication costs. This neuromorphic system will provide an effective solution to real-life energy-constrained applications and significantly contribute to the exploration of next-generation high-performance computing systems under the DOE context.

97 MATHEMATICS AND COMPUTING↗

Power and Efficiency Optimized in Traveling-Wave Tubes Over a Broad Frequency Bandwidth

A traveling-wave tube (TWT) is an electron beam device that is used to amplify electromagnetic communication waves at radio and microwave frequencies. TWT's are critical components in deep space probes, communication satellites, and high-power radar systems. Power conversion efficiency is of paramount importance for TWT's employed in deep space probes and communication satellites. A previous effort was very successful in increasing efficiency and power at a single frequency (ref. 1). Such an algorithm is sufficient for narrow bandwidth designs, but for optimal designs in applications that require high radiofrequency power over a wide bandwidth, such as high-density communications or high-resolution radar, the variation of the circuit response with respect to frequency must be considered. This work at the NASA Glenn Research Center is the first to develop techniques for optimizing TWT efficiency and output power over a broad frequency bandwidth (ref. 2). The techniques are based on simulated annealing, which has the advantage over conventional optimization techniques in that it enables the best possible solution to be obtained (ref. 3). Two new broadband simulated annealing algorithms were developed that optimize (1) minimum saturated power efficiency over a frequency bandwidth and (2) simultaneous bandwidth and minimum power efficiency over the frequency band with constant input power. The algorithms were incorporated into the NASA coupled-cavity TWT computer model (ref. 4) and used to design optimal phase velocity tapers using the 59- to 64-GHz Hughes 961HA coupled-cavity TWT as a baseline model. In comparison to the baseline design, the computational results of the first broad-band design algorithm show an improvement of 73.9 percent in minimum saturated efficiency (see the top graph). The second broadband design algorithm (see the bottom graph) improves minimum radiofrequency efficiency with constant input power drive by a factor of 2.7 at the high band edge (64 GHz) and increases simultaneous bandwidth by 500 MHz.

Wilson, Jeffrey D.↗

Control optimization of a lifting body entry problem by an improved and a modified method of perturbation function

A study of the solution problem of a complex entry optimization was studied. The problem was transformed into a two-point boundary value problem by using classical calculus of variation methods. Two perturbation methods were devised. These methods attempted to desensitize the contingency of the solution of this type of problem on the required initial co-state estimates. Also numerical results are presented for the optimal solution resulting from a number of different initial co-states estimates. The perturbation methods were compared. It is found that they are an improvement over existing methods.

Garcia, F., Jr.↗

Effect of Heat Treatment Conditions on Mechanical Properties and Precipitates in Sheet Metal Hot Stamping of 7075 Aluminum Alloy

Due to the low formability at room temperature, the application of 7XXX aluminum alloy sheet is limited. The hot forming-quenching process is an effective technology for the forming of some complex-shaped aluminum alloy parts. In this study, heat treatment was integrated with sheet metal stamping to improve formability and strength of 7075 aluminum alloy sheet. The effect of different heat treatment parameters on the strength of 7075 aluminum alloy sheet was investigated under stamping and heat treatment integrated process, based on which the optimal heat treatment combination was determined. Furthermore, the evolution of precipitates with the variation of aging temperature and time was studied by transmission electron microscope. In addition, quenching under water-cooled dies was conducted for 7075 aluminum alloy sheet after solution heat treatment, in which the hardness under die quenching was compared with that of underwater quenching and air quenching. Finally, the tensile test illustrates that, after die quenching and successive artificial aging, the tensile strength of 7075 aluminum alloy sheet was achieved at around 548 MPa. Shear fracture with long strip step-shaped pattern was observed in aging state.

36 MATERIALS SCIENCE↗

Nondestructive ultrasonic characterization of a triple-weld-bead wire arc additively manufactured ER70S-6 S-curved wall

Understanding build-scale microstructural variation in wire arc additive manufacturing (WAAM) of low-carbon steels is essential for ensuring consistent structure–property relationships throughout large components. Conventional destructive characterization techniques, such as scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), are time-intensive and limited to localized regions, making comprehensive evaluation of large WAAM structures challenging. In this study, a nondestructive ultrasonic approach was employed to characterize a 252 mm tall ER70S-6 S-curved WAAM wall produced using a triple-bead deposition strategy. Optical and SEM analysis revealed a repeating dual-region microstructure consisting of uniform polygonal ferrite at melt pool centers and heterogeneous ferrite with coarse and fine grains near melt pool boundaries, attributed to cyclic thermal conditions. Longitudinal ultrasonic backscatter imaging was used to evaluate the continuity of this periodicity along the full build height. The ultrasonic response exhibited a consistent repeating pattern that correlated with the observed layer-wise microstructural variation. X-ray computed tomography confirmed the absence of detectable porosity, indicating that ultrasonic contrast is primarily governed by grain morphology. Overall, the results indicate that longitudinal backscatter ultrasound is a promising nondestructive characterization technique for validating microstructural variations along the s-curved WAAM wall, with significant potential for microstructure optimization and process control.

36 MATERIALS SCIENCE↗

Identifying the Role of Magnesium Content in Assessing the Electrochemical Performance of (CoCuMgNiZn)O

High-entropy oxides (HEOs) featuring 5 or more metals in approximately equimolar ratios, such as the prototypical rock-salt-structured (CoCuMgNiZn)O, have attracted interest for their potential to display material properties superior to oxides with combinations of 4 or fewer of the component metals. In particular, (CoCuMgNiZn)O has shown promise as an anode for lithium-ion batteries with a high specific capacity retention over extended cycling. Previous studies have suggested that magnesium, despite being electrochemically inert, provides a crucial contribution to the favorable performance of this HEO by stabilizing the crystal structure through repeated charge–discharge cycles. This paper probes the extent and mechanism of the magnesium effect by using a facile microwave-assisted hydrothermal synthesis method to vary the level of Mg content. Moreover, we extensively characterized the product with techniques such as 4D-STEM and ICP-OES, which have not previously been applied in combination with this material, in order to elucidate the relationships among chemical composition, nanostructure, and performance. Here, we show that the level of Mg incorporation is positively correlated with long-term stability and negatively correlated with rate capacity, and that the latter effect yields a stronger influence upon the overall performance, with the best-performing sample possessing a Mg quantity equivalent to ∼1/5 that of an equimolar concentration. This finding demonstrates not only that the variation of individual elemental levels offers a promising and relatively unexplored avenue to optimize the electrochemical performance of HEO materials but also that it should not be assumed that equimolar compositions of constituent elements are necessarily the best.

36 MATERIALS SCIENCE↗