Search NASA⌕ Search

SEARCH · Search NASA

Results for “Coating processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Wear Resistance Enhancement of Ti-6Al-4 V Alloy by Applying Zr-Modified Silicide Coatings

Zr-modified silicide coatings were prepared on Ti-6Al-4 V alloy by pack cementation process to enhance its wear resistance. The microstructure and wear properties of the substrate and the coatings were comparatively investigated using GCr15 and Al{sub 2}O{sub 3} as the counterparts under different sliding loads. The obtained Zr-modified silicide coating had a multilayer structure, consisting of a thick (Ti,X)Si{sub 2} (X represents Al, Zr and V elements) outer layer, a TiSi middle layer and a Ti{sub 5}Si{sub 4} + Ti{sub 5}Si{sub 3} inner layer. The micro-hardness of the coating was much higher than the substrate and displayed a decrease tendency from the coating surface to the interior. Sliding against either GCr15 or Al{sub 2}O{sub 3} balls, the coatings showed superior anti-friction property to the Ti-6Al-4 V alloy, as confirmed by its much lower wear rate under each employed sliding condition.

36 MATERIALS SCIENCE↗

Development of an aerosol microphysical module: Aerosol Two-dimensional bin module for foRmation and Aging Simulation (ATRAS)

Number concentrations, size distributions, and mixing states of aerosols are essential parameters for accurate estimation of aerosol direct and indirect effects. In this study, we developed an aerosol module, designated Aerosol Two-dimensional bin module for foRmation and Aging Simulation (ATRAS), that can represent these parameters explicitly by considering new particle formation (NPF), black carbon (BC) aging, and secondary organic aerosol (SOA) processes. A two-dimensional bin representation is used for particles with dry diameters from 40 nm to 10 µm to resolve both aerosol size (12 bins) and BC mixing state (10 bins) for a total of 120 bins. The particles with diameters from 1 to 40 nm are resolved using an additional 8 size bins to calculate NPF. The ATRAS module was implemented in the WRF-chem model and applied to examine the sensitivity of simulated mass, number, size distributions, and optical and radiative parameters of aerosols to NPF, BC aging and SOA processes over East Asia during the spring of 2009. BC absorption enhancement by coating materials was about 50% over East Asia during the spring, and the contribution of SOA processes to the absorption enhancement was estimated to be 10 – 20% over northern East Asia and 20 – 35% over southern East Asia. A clear north-south contrast was also found between the impacts of NPF and SOA processes on cloud condensation nuclei (CCN) concentrations: NPF increased CCN concentrations at higher supersaturations (smaller particles) over northern East Asia, whereas SOA increased CCN concentrations at lower supersaturations (larger particles) over southern East Asia. Application of ATRAS to East Asia also showed that the impact of each process on each optical and radiative parameter depended strongly on the process and the parameter in question. The module can be used in the future as a benchmark model to evaluate the accuracy of simpler aerosol models and examine interactions between NPF, BC aging, and SOA processes under different meteorological conditions and emissions.

Matsui, H.↗

Synthesis and characterization of anatase TiO{sub 2} nanotubes with controllable crystal size by a simple MWCNT template method

Highly crystalline phase-pure anatase TiO{sub 2} nanotubes were produced by performing a simple calcinations process in air of the TiO{sub 2} coated MWCNTs composite material prepared by an in situ sol-gel method. A homogeneous thin coating layer of TiO{sub 2} on the surface of MWCNTs is firstly obtained. Calcination in ambient air at appropriate temperatures is performed to transform phase of TiO{sub 2} into anatase and remove MWCNTs simultaneously, resulting in pure anatase TiO{sub 2} nanotubes. Both end tips of the nanotubes are observed to be closed, probably due to covering up MWCNTs with TiO{sub 2} particles. The crystallization of anatase phase was formed upon 350 Degree-Sign C, and MWCNTs are completely oxidized between 500 and 650 Degree-Sign C, leaving anatase TiO{sub 2} nanotubes with an average crystal size increasing from about 8 to 24 nm as the temperature rises. Moreover, the tubular structure was found to collapse after calcinations at 700 Degree-Sign C. - Graphical abstract: TGA analysis and TEM images of the samples after calcinations in air at different temperatures: (a) before calcinations, (b) 350 Degree-Sign C, (c) 500 Degree-Sign C, and (d) 650 Degree-Sign C. Highlights: Black-Right-Pointing-Pointer Highly crystalline and stable phase-pure anatase TiO{sub 2} nanotubes were produced by a simply MWCNT template method. Black-Right-Pointing-Pointer A homogeneous thin coating layer of TiO{sub 2} on the surface of MWCNTs could be obtained. Black-Right-Pointing-Pointer Small crystal size of anatase is formed at lower temperatures and higher temperatures cause significant increase of crystal size from 8 to 24 nm. Black-Right-Pointing-Pointer Convex closed tip structure of TiO{sub 2} nanotubes is formed owing to the good coating of TiO{sub 2}.

36 MATERIALS SCIENCE↗

Evaluation of critical heat flux of ATF candidate coating materials in pool boiling

The critical heat flux (CHF) of potential accident tolerant fuel (ATF) cladding materials and concepts, Cr and FeCrAl coatings on zirconium-alloy substrates, was investigated experimentally. A cold spray process, which involves the propulsion of high velocity powder particles on to the substrate surface to form a coating upon impact, was used to create the coatings. Surface parameters such as contact angle, surface roughness, and morphology that are associated with CHF in pool boiling were characterized. Non-hydrodynamic effects of newly developed ATF candidate coating materials on CHF were also evaluated. The effects of thermal properties and coating thickness and expected challenges for evaluation of CHF for new ATF cladding materials development are discussed.

36 MATERIALS SCIENCE↗

Spatial atomic layer deposition on flexible porous substrates: ZnO on anodic aluminum oxide films and Al{sub 2}O{sub 3} on Li ion battery electrodes

Spatial atomic layer deposition (S-ALD) was examined on flexible porous substrates utilizing a rotating cylinder reactor to perform the S-ALD. S-ALD was first explored on flexible polyethylene terephthalate polymer substrates to obtain S-ALD growth rates on flat surfaces. ZnO ALD with diethylzinc and ozone as the reactants at 50 °C was the model S-ALD system. ZnO S-ALD was then performed on nanoporous flexible anodic aluminum oxide (AAO) films. ZnO S-ALD in porous substrates depends on the pore diameter, pore aspect ratio, and reactant exposure time that define the gas transport. To evaluate these parameters, the Zn coverage profiles in the pores of the AAO films were measured using energy dispersive spectroscopy (EDS). EDS measurements were conducted for different reaction conditions and AAO pore geometries. Substrate speeds and reactant pulse durations were defined by rotating cylinder rates of 10, 100, and 200 revolutions per minute (RPM). AAO pore diameters of 10, 25, 50, and 100 nm were utilized with a pore length of 25 μm. Uniform Zn coverage profiles were obtained at 10 RPM and pore diameters of 100 nm. The Zn coverage was less uniform at higher RPM values and smaller pore diameters. These results indicate that S-ALD into porous substrates is feasible under certain reaction conditions. S-ALD was then performed on porous Li ion battery electrodes to test S-ALD on a technologically important porous substrate. Li{sub 0.20}Mn{sub 0.54}Ni{sub 0.13}Co{sub 0.13}O{sub 2} electrodes on flexible metal foil were coated with Al{sub 2}O{sub 3} using 2–5 Al{sub 2}O{sub 3} ALD cycles. The Al{sub 2}O{sub 3} ALD was performed in the S-ALD reactor at a rotating cylinder rate of 10 RPM using trimethylaluminum and ozone as the reactants at 50 °C. The capacity of the electrodes was then tested versus number of charge–discharge cycles. These measurements revealed that the Al{sub 2}O{sub 3} S-ALD coating on the electrodes enhanced the capacity stability. This S-ALD process could be extended to roll-to-roll operation for the commercialization of S-ALD for coating Li ion battery electrodes.

36 MATERIALS SCIENCE↗

Atomically Bonded Transparent Superhydrophobic Coatings

Maintaining clarity and avoiding the accumulation of water and dirt on optically transparent surfaces such as US military vehicle windshields, viewports, periscope optical head windows, and electronic equipment cover glasses are critical to providing a high level of visibility, improved survivability, and much-needed safety for warfighters in the field. Through a combination of physical vapor deposition techniques and the exploitation of metastable phase separation in low-alkali borosilicate, a novel technology was developed for the fabrication of optically transparent, porous nanostructured silica thin film coatings that are strongly bonded to glass platforms. The nanotextured films, initially structurally superhydrophilic, exhibit superior superhydrophobicity, hence antisoiling ability, following a simple but robust modification in surface chemistry. The surfaces yield water droplet contact angles as high as 172°. Moreover, the nanostructured nature of these coatings provides increased light scattering in the UV regime and reduced reflectivity (i.e., enhanced transmission) over a broad range of the visible spectrum. In addition to these functionalities, the coatings exhibit superior mechanical resistance to abrasion and are thermally stable to temperatures approaching 500°C. The overall process technology relies on industry standard equipment and inherently scalable manufacturing processes and demands only nontoxic, naturally abundant, and inexpensive base materials. Such coatings, applied to the optical components of current and future combat equipment and military vehicles will provide a significant strategic advantage for warfighters. The inherent self-cleaning properties of such superhydrophobic coatings will also mitigate biofouling of optical windows exposed to high-humidity conditions and can help decrease repair/replacement costs, reduce maintenance, and increase readiness by limiting equipment downtime.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

CORROSION RESISTANCE OF LASER-INTERFERENCE STRUCTURED ALUMINUM ALLOY 2024 COATED WITH MIL-PRF-85582 PRIMER

The use of aluminum alloys in aerospace industry requires more effective and reliable joining techniques. The lubricant contaminants from prior rolling operations affect surface energies and the quality of coating adhe-sion and adhesive bonded joints. In this study, a new laser-based technique is investigated as a surface treatment for coating applications. The laser interference power profile was created by splitting the beam and guiding both beams towards the specimen and overlapping them on the specimen surface, creating a line-interference pattern on the specimen surface. The laser-interference structuring (LIS) was used without any chemical treatments, such as those in chemical conversion coating (CCC) and sulfuric acid anodizing (SAA), which is a much simpler process than those chemical-based. To assess the effect of LIS on corrosion re-sistance of coating, Al 2024 panels prepared by LIS, CCC and SAA were coated with MIL-PRF-85582, Type I, Class N primer and exposed to salt spray environment according to ASTM B117. The exposure is currently in progress and the corrosion attack on the coated panels will be evaluated by the degree of blister formation and rust creepage.

Sabau, Adrian↗

Spray coating for washout tooling by binder jet additive manufacturing

We report washout tooling is a process in which a removable mold or fixture is disintegrated using a solvent. Binder Jet (BJ) additive manufacturing holds promise for creating customized washout molds from common materials. BJ-based washout tooling provides an advanced strategy in manufacturing fiber-reinforced composites (FRCs), especially for customized hollow FRCs. However, washout tools formed by BJ require an impermeable barrier between the porous tooling surface and the parts laid up on the surface to prevent the resin from infiltrating the tooling surface and bonding the tool to the FRC. The conventional method for preventing resin migration into the washout mold from the FRC is winding Teflon® tape over the entire surface, which is labor-intensive and very difficult to deploy for specific geometries. Here, we report the development of a polymer spray coating method to seal the tooling surface and prevent resin infiltration without affecting the washout properties needed for sacrificial tooling. Two water-soluble polymers, poly(sodium 4-styrenesulfonate) (PSS–Na) and poly(vinylsulfonic acid, sodium salt) (PVS–Na), were investigated for spray coating. PVS-Na maintained tighter geometric tolerances and provided excellent thermal stability with the onset of decomposition at 320 °C and glass transition temperature of 280 °C. Spray coating with PVS-Na streamlines the process of forming a protective layer for the washout molds by BJ, reduces migration of the resins from the FRC, and significantly improves the production efficiency of complex washout tools.

42 ENGINEERING↗

Fabrication of highly efficient carbon coated exfoliated tungsten disulfide nanosheets core-shell nanostructure as a promising solar-light driven photocatalyst

Highlights: • Investigated the benefits of exfoliation mechanism of WS{sub 2} nanosheets. • C@e-WS{sub 2} was successfully synthesized via two step exfoliation -hydrothermal process. • C@e-WS{sub 2} core-shell confirmed by HRTEM. • C@e-WS{sub 2} core-shell photocatalyst exhibited excellent photocatalytic activity. • Photodegradation mechanism of C@e-WS{sub 2} photocatalyst is elucidated and discussed. - Abstract: Exfoliated Tungsten disulfide (e-WS{sub 2}) nanosheets were obtained from bulk Tungsten disulfide (WS{sub 2}) in a liquid-phase ultrasonic exfoliation method using a DMF solvent. Core-shell mannered carbon coating was developed by hydrothermal process on exfoliated Tungsten disulfide (e-WS{sub 2}) to enhance the efficient charge separation, specific surface area with mesoporosity and stability for chemical processes and mechanical strains. The carbon coated e-WS{sub 2} nanosheets (C@e-WS{sub 2}) was performed by series of characterization techniques and explored to the photocatalytic degradation of malachite green (MG) dye by comparing with bulk WS{sub 2} and e-WS{sub 2}. Among all the photocatalysts highest performance was observed for the C@e-WS{sub 2}. C@e-WS{sub 2} catalyst displays more than 11 fold enhancements in the photocomposition rate of MG over bulk WS{sub 2} and nearly 8 fold improvements over e-WS{sub 2} for 90 min irradiation. In addition, for complete degradation of MG dye over the bulk WS{sub 2}, e-WS{sub 2}, and C@e-WS{sub 2} catalysts were observed at 150, 130, and 90 min under simulated solar light irradiation. The results obtained using core-shell mannered C@e-WS{sub 2} are stepping stone for developing cost-effective and noble metal-free catalysts for photodegradation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Tribological and Corrosion Properties of Coatings Produced by Plasma Electrolytic Oxidation on the ZA27 Alloy

In this paper, a continuous and dense coating was deposited on samples of the ZA27 alloy through the plasma electrolytic oxidation (PEO) process to improve its wear and corrosion performance. A nontoxic and environmentally friendly inorganic salt, Na{sub 2}SiO{sub 3}, is chosen as electrolytes with different concentrations. The effect of the concentration of Na{sub 2}SiO{sub 3} aqueous solutions on the coating performances was investigated. The coatings with 3Al{sub 2}O{sub 3}·2SiO{sub 2} (mullite), Zn{sub 2}SiO{sub 4} and Al{sub 2}O{sub 3} (either crystal phase or with some amorphous SiO{sub 2} phases) were formed by the PEO processes. It was found that the coating thickness increased with the increase in electrolyte concentration. However, the wear and corrosion resistance performance of the coatings did not improve as the coating’s thickness increased. This was due to the fact that the coating produced with electrolytes of 10 g/L has a porous structure with large pore size. Among all the samples, coating produced by 15 g/L Na{sub 2}SiO{sub 3} has the best wear and corrosion resistance, which is attributed to its continuous and dense structure with thickness of about 47 μm.

36 MATERIALS SCIENCE↗

An inorganic coating and flexible regulating in situ of stent endothelialization by the controllable ion releasing

Highlights: • The Cu/Ti film with regulating the various responses of ECs and SMCs has been prepared. • The hemocompatibility could be adjusted via the ratio of Cu/Ti. • The volume and velocity of copper ion released from film was designed via the preparation processing. - Abstract: A facile approach to fabricate an inorganic coating with favorable blood compatibility and accelerating endothelialization is reported. The inorganic coating with various ratios of Cu and Ti atom are prepared on 316 L stainless steel by physical vapor deposition method. The phase composition and structure as well as the element concentration of the coating are investigated by X-ray diffraction and X-photoelectron energy spectrum. The hemolysis ratio, clotting time and platelet adhesion are utilized to characterize the materials’ hemocompatibility, the copper ion releasing was also investigated via immersing test. The result indicates that copper-titanium coating show good compatibility; however, as the ratio of Cu to Ti increases, the hemolysis ratio also increases. The endothelialization degree was accelerated owing to maintain less than 7.0 μg/ml of Cu{sup 2+} concentrate, and endothelial cells proliferate more readily than smooth muscle cells. The results demonstrate that this degradable copper-containing coating is suitable as a new surface modification for vascular stents.

36 MATERIALS SCIENCE↗

Transuranic (TRU) Waste Repackaging at the Nevada Test Site

This paper describes the activities required to modify a facility and the process of characterizing, repackaging, and preparing for shipment the Nevada Test Site’s (NTS) legacy transuranic (TRU) waste in 58 oversize boxes (OSB). The waste, generated at other U.S. Department of Energy (DOE) sites and shipped to the NTS between 1974 and 1990, requires size-reduction for off-site shipment and disposal. The waste processing approach was tailored to reduce the volume of TRU waste by employing decontamination and non-destructive assay. As a result, the low-level waste (LLW) generated by this process was packaged, with minimal size reduction, in large sea-land containers for disposal at the NTS Area 5 Radioactive Waste Management Complex (RWMC). The remaining TRU waste was repackaged and sent to the Idaho National Laboratory Consolidation Site for additional characterization in preparation for disposal at the Waste Isolation Pilot Plant (WIPP), near Carlsbad, New Mexico. The DOE National Nuclear Security Administration Nevada Site Office and the NTS Management and Operating (M&O) contractor, NSTec, successfully partnered to modify and upgrade an existing facility, the Visual Examination and Repackaging Building (VERB). The VERB modifications, including a new ventilation system and modified containment structure, required an approved Preliminary Documented Safety Analysis prior to project procurement and construction. Upgrade of the VERB from a radiological facility to a Hazard Category 3 Nuclear Facility required new rigor in the design and construction areas and was executed on an aggressive schedule. The facility Documented Safety Analysis required that OSBs be vented prior to introduction into the VERB. Box venting was safely completed after developing and implementing two types of custom venting systems for the heavy gauge box construction. A remotely operated punching process was used on boxes with wall thickness of up to 3.05 mm (0.120 in) to insert aluminum bronze filters and sample ports to prevent sparking during penetration. A remotely operated cold-drilling process with self-drilling, self-tapping titanium coated spark-resistant filters was used for boxes with wall thickness of up to 6.35 mm (0.25 in). The box headspace was sampled for the presence of flammable gases. To further accelerate the project schedule, an innovative treatment process was used. Several of the OSBs were re-assayed and determined to be mixed low-level waste (MLLW) which allowed treatment, followed by disposal in the Mixed Waste Disposal Unit at the NTS Area 5 Radioactive Waste Management Complex (RWMC). The MLLW boxes were certified using real-time radiography and overpacked into custom-built polyethylene-lined macroencapsulation containers. The polyethylene-lined lid was welded to the poly-lined box using automatically controlled resistance heating through embedded wiring in the lid. The work was performed under the existing Documented Safety Analysis since plastic welding is accomplished at low temperature and does not introduce the risks of other macroencapsulation processes, such as welding stainless steel containers. The macroencapsulation process for MLLW not only accelerated the schedule by reducing the number of boxes requiring size reduction, but it also resulted in significantly improved safety with as low as reasonable achievable levels of exposure to workers plus reduced cost by eliminating the need to perform repackaging in the VERB.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Energy-Saving Melting and Revert Reduction Technology (E-SMARRT): Use of Laser Engineered Net Shaping for Rapid Manufacturing of Dies with Protective Coatings and Improved Thermal Management

In the high pressure die casting process, molten metal is introduced into a die cavity at high pressure and velocity, enabling castings of thin wall section and complex geometry to be obtained. Traditional die materials have been hot work die steels, commonly H13. Manufacture of the dies involves machining the desired geometry from monolithic blocks of annealed tool steel, heat treating to desired hardness and toughness, and final machining, grinding and polishing. The die is fabricated with internal water cooling passages created by drilling.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Development and Understanding of Nb 3 Sn films for radiofrequency applications through a sample-host 9-cell cavity

Nb 3 Sn is a promising advanced material under development for superconducting radiofrequency cavities. Past efforts have been focused primarily on small development-scale cavities, but large, often multi-celled cavities, are needed for particle accelerator applications. In this work, we report on successful Nb 3 Sn coatings on Nb in a 1 m-long 9-cell Nb sample-host cavity at Fermilab. The geometry of the first coating with only one Sn source made it possible to study the influence of Sn flux on the microstructure. Based on these results, we postulate a connection between recently observed anomalously large thin grains and uncovered niobium spots observed in the past by other authors (Trenikhina et al 2018 Supercond. Sci. Technol. 32 015004). A phenomenological model to explain how these anomalously large grains could form is proposed. Overall, this model is invoked to provide possible explanations for literature results from several groups and to guide key process parameters to achieve uniform vapor-diffusion coatings, when applied to complex structures as the multi-cell cavity under study.

43 PARTICLE ACCELERATORS↗

Chemical weathering of layered Ni-rich oxide electrode materials: Evidence for cation exchange

Lithiated ternary oxides containing nickel, cobalt, and manganese are intercalation compounds that are used as positive electrodes in high-energy lithium-ion batteries. These materials undergo compositional changes that adversely affect their cycling performance when they are stored in humid air or exposed to moisture. There is a new urgency to better understanding of these “weathering” processes as manufacturing moves towards a more environmentally benign aqueous processing of the positive electrode. Delithiation in the oxide subsurface regions and the formation of lithium salts (such as hydroxides and carbonates) coating the surface, have been suggested as chemical drivers for these processes, but the mechanistic details remain poorly known. The redox reactions which follow oxide delithiation are believed to cause all of the observed transformations. In this article we suggest another possibility: namely, the proton – lithium exchange. We argue that this hypothesis provides a simple, comprehensive rationale for our observations from X-ray diffraction, X-ray photoelectron spectroscopy, scanning transmission electron microscopy, and electrochemical measurements. These observations include contraction of the c-axis (unit cell) lattice parameter, strain in the crystalline oxide bulk, directionality of the chemical damage, formation of amorphous surface films, and the partial recovery of capacity loss by electrochemical relithiation of the material. Lastly, these effects need to be mitigated before aqueous processing of the positive electrode can find widespread adoption during cell manufacturing.

25 ENERGY STORAGE↗

TiN coated aluminum electrodes for DC high voltage electron guns

Preparing electrodes made of metals like stainless steel, for use inside DC high voltage electron guns, is a labor-intensive and time-consuming process. In this paper, the authors report the exceptional high voltage performance of aluminum electrodes coated with hard titanium nitride (TiN). The aluminum electrodes were comparatively easy to manufacture and required only hours of mechanical polishing using silicon carbide paper, prior to coating with TiN by a commercial vendor. The high voltage performance of three TiN-coated aluminum electrodes, before and after gas conditioning with helium, was compared to that of bare aluminum electrodes, and electrodes manufactured from titanium alloy (Ti-6Al-4V). Following gas conditioning, each TiN-coated aluminum electrode reached −225 kV bias voltage while generating less than 100 pA of field emission (<10 pA) using a 40 mm cathode/anode gap, corresponding to field strength of 13.7 MV/m. Smaller gaps were studied to evaluate electrode performance at higher field strength with the best performing TiN-coated aluminum electrode reaching ∼22.5 MV/m with field emission less than 100 pA. These results were comparable to those obtained from our best-performing electrodes manufactured from stainless steel, titanium alloy and niobium, as reported in references cited below. The TiN coating provided a very smooth surface and with mechanical properties of the coating (hardness and modulus) superior to those of stainless steel, titanium-alloy, and niobium electrodes. These features likely contributed to the improved high voltage performance of the TiN-coated aluminum electrodes.

36 MATERIALS SCIENCE↗

Enhanced Flux and Electrochemical Cleaning of Silicate Scaling on Carbon Nanotube-Coated Membrane Distillation Membranes Treating Geothermal Brines

The desalination of inland brackish groundwater offers the opportunity to provide potable drinking water to residents and industrial cooling water to industries located in arid regions. Geothermal brines are used to generate electricity, but often contain high concentrations of dissolved salt. Here in this paper, we demonstrate how the residual heat left in spent geothermal brines can be used to drive a membrane distillation (MD) process and recover desalinated water. Porous polypropylene membranes were coated with a carbon nanotube (CNT)/poly(vinyl alcohol) layer, resulting in composite membranes having a binary structure that combines the hydrophobic properties critical for MD with the hydrophilic and conductive properties of the CNTs. We demonstrate that the addition of the CNT layer increases membrane flux due to enhanced heat transport from the bulk feed to the membrane surface, a result of CNT's high thermal transport properties. Furthermore, we show how hydroxide ion generation, driven by water electrolysis on the electrically conducting membrane surface, can be used to efficiently dissolve silicate scaling that developed during the process of desalinating the geothermal brine, negating the need for chemical cleaning.

15 GEOTHERMAL ENERGY↗

Combinatorial chemical bath deposition of CdS contacts for chalcogenide photovoltaics

Contact layers play an important role in thin film solar cells, but new material development and optimization of its thickness is usually a long and tedious process. A high-throughput experimental approach has been used to accelerate the rate of research in photovoltaic (PV) light absorbers and transparent conductive electrodes, however the combinatorial research on contact layers is less common. Here, we report on the chemical bath deposition (CBD) of CdS thin films by combinatorial dip coating technique and apply these contact layers to Cu(In,Ga)Se 2 (CIGSe) and Cu 2 ZnSnSe 4 (CZTSe) light absorbers in PV devices. Combinatorial thickness steps of CdS thin films were achieved by removal of the substrate from the chemical bath, at regular intervals of time, and in equal distance increments. The trends in the photoconversion efficiency and in the spectral response of the PV devices as a function of thickness of CdS contacts were explained with the help of optical and morphological characterization of the CdS thin films. The maximum PV efficiency achieved for the combinatorial dip-coating CBD was similar to that for the PV devices processed using conventional CBD. Finally, the results of this study lead to the conclusion that combinatorial dip-coating can be used to accelerate the optimization of PV device performance of CdS and other candidate contact layers for a wide range of emerging absorbers.

14 SOLAR ENERGY↗