Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inlets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Engine inlet distortion in a 9.2 percent scaled vectored thrust STOVL model in ground effect

Advanced Short Takeoff/Vertical Landing (STOVL) aircraft which can operate from remote locations, damaged runways, and small air capable ships are being pursued for deployment around the turn of the century. To achieve this goal, a cooperative program has been defined for testing in the NASA Lewis 9- by 15-foot Low Speed Wind Tunnel (LSWT) to establish a database for hot gas ingestion, one of the technologies critical to STOVL. This paper presents results showing the engine inlet distortions (both temperature and pressure) in a 9.2 percent scale Vectored Thrust STOVL model in ground effects. Results are shown for the forward nozzle splay angles of 0, -6, and 18 deg. The model support system had 4 deg of freedom, heated high pressure air for nozzle flow, and a suction system exhaust for inlet flow. The headwind (freestream) velocity was varied from 8 to 23 kn.

Johns, Albert L.↗
NASA NTRS1990

Three-dimensional shock-shock interactions on the scramjet inlet

The effects of shock impingement on the inlet of a scramjet engine are investigated numerically. The impinging shock is caused by the vehicle forebody. The interaction of this forebody shock with the inlet leading edge shock results in a very complex fully three-dimensional flowfield containing local regions of high pressure and intense heating. In the present investigation, this complex flowfield is calculated by solving the thin-layer Navier-Stokes equations using a finite-volume flux splitting technique due to van Leer. For zero or small sweep angles a Type IV interaction occurs while for moderate sweep of about 25 deg, a Type V interaction occurs. Both Type IV and Type V interactions are investigated.

Singh, D. J.↗
NASA NTRS1990

A flux-split solution procedure for unsteady inlet flows

The unstart and restart of an axisymmetric inlet is investigated using a flux-split procedure applied to the Euler and Reduced Navier Stokes (RNS) equations. A time consistent direct sparse matrix solver is applied to compute the transient flow field both internal and external to the inlet. Time varying oblique and normal shocks are captured. The code is quite general and is applicable for subsonic, transonic and supersonic free streams. The current analysis is concerned with supersonic flight conditions.

Pordal, H. S.↗
NASA NTRS1990

Comparison of 3-D viscous flow computations of Mach 5 inlet with experimental data

The accuracy of the time-marching three-dimensional Navier-Stokes code PARC3D (Cooper et al., 1987) is evaluated using experimental data on a Mach 5 mixed-compression inlet configuration, obtained in the 10 x 10-ft working section of the supersonic wind tunnel at NASA Lewis. The basic principles of the PARC3D computations (in which the inlet and tunnel geometry and the bleed conditions are fully modeled) and the experimental setup are described, and the results are presented in extensive graphs and characterized in detail. PARC3D is shown to give reasonably accurate predictions of the bleed-zone elimination of low-energy vortical flow due to shock/boundary-layer interaction; various possible improvements are briefly considered.

Reddy, D. R.↗
NASA NTRS1987

Shuttle Centaur engine cooldown evaluation and effects of expanded inlets on start transient

As part of the integration of the RL10 engine into the Shuttle Centaur vehicle, a satisfactory method of conditioning the engine to operating temperatures had to be established. This procedure, known as cooldown, is different from the existing Atlas Centaur due to vehicle configuration and mission profile differenced. The program is described, and the results of a Shuttle Centaur cooldown program are reported. Mission peculiarities cause substantial variation in propellant inlet conditions between the substantiated Atlas Centaur and Shuttle Centaur with the Shuttle Centaur having much larger variation in conditions. A test program was conducted to demonstrate operation of the RL10 engine over the expanded inlet conditions. As a result of this program, the Shuttle Centaur requirements were proven satisfactory. Minor configuration changes incorporated as a result of this program provide substantial reduction in cooldown propellant consumption.

Source record↗
NASA NTRS1991

Two and three-dimensional shock-shock interactions on the blunt leading edges of the hypersonic inlets

The effect of shock impingement on the blunt leading edges of the top and sidewall compression type inlet of a scramjet engine is studied numerically. The impinging shock is caused by the vehicle forebody. The interaction of this forebody shock with the inlet leading edge shock results in a very complex flowfield containing local regions of high pressure and intense heating. This complex flowfield in calculated by solving the Navier-Stokes equations using a finite volume flux splitting technique due to van Leer. To resolve the finer details of the flow structure as well as to predict the surface heat transfer accurately, adaptive grid technique is used in the analysis. Results of the present numerical study are compared with available experimental results.

Singh, D. J.↗
NASA NTRS1991

Tests in Helium Illustrate High Mach Number Inlet-Forebody Interactions

High Mach helium tests are described in the form of the view-graphs. The following topics are included: high-speed inlet-forebody interaction tests; helium tunnel; boundary layer approaching inlet; ramp surface pressure distribution; static pressure on ramp; and pressure variation across wedge and ramp.

Weidner, John↗
NASA NTRS1991

Navier-Stokes simulation of inlet flow fields-experimental verification

The objectives were to develop a state-of-the-art numerical capability for the prediction of internal and external flow fields, validate the Navier-Stokes solution for internal flows, treat realistic diffuser inlet systems, and provide a technical base for inlet system design. Progress is reported in viewgraph form.

Chyu, Wei J.↗
NASA NTRS1991

Wind tunnel blockage study of a generic three-dimensional sidewall compression scramjet inlet at Mach 10

A large scale model of a generic three-dimensional sidewall compression scramjet inlet has been designed based on the results of a computational parametric study for testing in the 31-inch Mach 10 Hypersonic Wind Tunnel at the NASA Langley Research Center. In order to increase the instrumentation density in interaction regions for a highly instrumented model, it is desirable to make the model as large as possible. When the cross-sectional area of a model becomes large relative to the inviscid core size of the tunnel, the effects of blockage must be considered. In order to assess these effects, a blockage model (an inexpensive, much less densely instrumented version of the configuration) was fabricated for preliminary testing. Since it was desired to determine both the effect of the model on the performance of the wind tunnel and also to determine if the inlet would start, the model possessed a total of 32 static pressure orifices distributed on the forebody plane and sidewalls; seventeen static pressure orifices on the tunnel wall and 3 pitot probes on the model monitored the tunnel performance. This paper presents the design considerations in the development of the wind tunnel model and the blockage aspects of the effects of contraction ratio, cowl location, Reynolds number, and angle of attack.

Holland, Scott D.↗
NASA NTRS1991

Contraction ratio effects in a generic sidewall compression scramjet inlet - A computational and experimental investigation

Computed and experimental data on a generic three-dimensional sidewall compression scramjet inlet with a leading edge sweep of 45 degrees at Mach 20 are presented. A three-dimensional Navier-Stokes code was adapted to perform preliminary parametric studies leading to the present configuration. Following the design phase, the code was then employed as an analysis tool to provide a better understanding of the flow field and the experimental static and pitot pressure data. The model possessed 240 static pressure orifices distributed on the forebody plane, sidewalls, and cowl and was tested in the 31 Inch Mach 10 facility at the NASA Langley Research Center. Pitot rakes were employed to map the entrance and exit planes. The contraction ratio was observed to have a dominant effect on the inlet shock structure and performance; these effects are the emphasis of the present report. In addition to pressure measurements, oil flows were used for further visualization and comparison with computation.

Holland, Scott D.↗
NASA NTRS1990

Inlets, ducts, and nozzles

The internal fluid mechanics research program in inlets, ducts, and nozzles consists of a balanced effort between the development of computational tools (both parabolized Navier-Stokes and full Navier-Stokes) and the conduct of experimental research. The experiments are designed to better understand the fluid flow physics, to develop new or improved flow models, and to provide benchmark quality data sets for validation of the computational methods. The inlet, duct, and nozzle research program is described according to three major classifications of flow phenomena: (1) highly 3-D flow fields; (2) shock-boundary-layer interactions; and (3) shear layer control. Specific examples of current and future elements of the research program are described for each of these phenomenon. In particular, the highly 3-D flow field phenomenon is highlighted by describing the computational and experimental research program in transition ducts having a round-to-rectangular area variation. In the case of shock-boundary-layer interactions, the specific details of research for normal shock-boundary-layer interactions are described. For shear layer control, research in vortex generators and the use of aerodynamic excitation for enhancement of the jet mixing process are described.

Abbott, John M.↗
NASA NTRS1992

Three-dimensional simulation of a translating strut inlet

A three-dimensional Navier-Stokes code is used to numerically simulate the flow through a translating strut scramjet inlet. The inlet has variable geometry for efficient operation over a wide speed range. Overall flow-field features such as the corner flow, topwall separation, shockwave coalescence, cowl pressure increase, and flow distortion at the throat are investigated. Comparisons are made with experimental results to provide for the assessment of the present analysis. Effects of boundary-layer ingestion on the overall flow features are also investigated.

Singh, D. J.↗
NASA NTRS1992

Leading edge sweep effects in generic three-dimensional sidewall compression scramjet inlets

A computational and experimental study of generic 3D sidewall compression inlets is conducted to examine the effects of fore and aft leading edge sweep on the internal shock structure. Inlets with leading edge sweeps of +30 deg and -30 deg with sidewall compression angles of 6 deg were tested in the NASA Langley Mach 4 air tunnel at a geometric contraction ratio of 1.87. The principal difference in performance was determined to be in the mass capture. Spillage was identified as having two components: a pressure induced component and a sweep induced component. It was found that while the direction of the leading edge sweep had a large influence on the spillage, the pressure effects were more important.

Cozart, Aaron B.↗
NASA NTRS1992

The effects of inlet flow modification on cavitating inducer performance

This paper explores the effect of inlet flow modification on the cavitating and noncavitating performance of two cavitating inducers, one of simple helical design and the other a model of the low-pressure LOX pump in the Space Shuttle Main Engine. The modifications were generated by sections of honeycomb, both uniform and nonuniform. Significant improvement in the performance over a wide range of flow coefficients resulted from the use of either honeycomb section. Measurements of the axial and swirl velocity profiles of the flows entering the inducers were made in order to try to understand the nature of the inlet flow and the manner in which it is modified by the honeycomb sections.

Del Valle, J.↗
NASA NTRS1992

Bleed-boundary conditions for numerically simulated mixed-compression supersonic inlet flow

A numerical study was performed to investigate boundary conditions for bleed openings that are needed in the numerical simulation of critical flow through turbojet inlets with bleed. Nine different boundary conditions (BCs) were devised and examined. Of the BCs examined, three were able to stabilize the terminal shock near the inlet's throat. This numerical study was based on the ensemble-averaged, unsteady, three-dimensional, compressible Navier-Stokes equations closed by the Baldwin-Lomax algebraic turbulence model. Solutions to the Navier-Stokes equations were obtained by using a hybrid implicit-explicit method (Beam and Warming/MacCormack). The multiblock grid system used in the solution procedure was generated by solving a set of elliptic partial differential equations. Solutions obtained were compared with available experimental data.

Chyu, W. J.↗
NASA NTRS1992

Full Navier-Stokes calculations on the installed F/A-18 inlet at a high angle of attack

Major objectives of the NASA High-Alpha Technology Program are the accurate prediction of the internal (inlet) aerodynamics of an aircraft operating at attitudes of up to 60 deg pitch and 10 deg yaw and the calibration of CFD codes for predicting the internal performance of inlets. Numerical results are presented for the three cases of a full-scale model, a 20-percent scale model at design mass flow, and a scale model at reduced mass flow; attention is given to the effects of Reynolds number. All three cases are at 30 deg angle of attack and zero deg yaw. The results thus obtained are helpful to experimentalists in determining some of their instrumentation requirements.

Bruns, James E.↗
NASA NTRS1993

Acoustic mode measurements in the inlet of a model turbofan using a continuously rotating rake: Data collection/analysis techniques

The rotating microphone measurement technique and data analysis procedures are documented which are used to determine circumferential and radial acoustic mode content in the inlet of the Advanced Ducted Propeller (ADP) model. Circumferential acoustic mode levels were measured at a series of radial locations using the Doppler frequency shift produced by a rotating inlet microphone probe. Radial mode content was then computed using a least squares curve fit with the measured radial distribution for each circumferential mode. The rotating microphone technique is superior to fixed-probe techniques because it results in minimal interference with the acoustic modes generated by rotor-stator interaction. This effort represents the first experimental implementation of a measuring technique developed by T. G. Sofrin. Testing was performed in the NASA Lewis Low Speed Anechoic Wind Tunnel at a simulated takeoff condition of Mach 0.2. The design is included of the data analysis software and the performance of the rotating rake apparatus. The effect of experiment errors is also discussed.

Hall, David G.↗
NASA NTRS1992

Acoustic Mode Measurements in the Inlet of a Model Turbofan Using a Continuously Rotating Rake

Comprehensive measurements of the spinning acoustic mode structure in the inlet of the Advanced Ducted Propeller (ADP) have been completed. These measurements were taken using a unique and previously untried method which was first proposed by T.G. Sofrin. A continuously rotating microphone system was employed. The ADP model was designed and built by Pratt & Whitney and tested in the NASA Lewis 9- by 15-foot Anechoic Wind Tunnel. Three inlet configurations were tested with cut-on and cutoff stator vane sets. The cutoff stator was designed to suppress all modes at the blade passing frequency. Rotating rake measurements indicate that several extraneous circumferential modes were active. The mode orders suggest that their source was an interaction between the rotor and small interruptions in the casing tip treatment. The cut-on stator produced the expected circumferential modes plus higher levels of the unexpected modes seen with the cutoff stator.

Heidelberg, Laurence J.↗