SEARCH · Search NASA

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Near-Net-Shape Hot Isostatic Press Manufacturing Modality for sCO2 CSP Capital Cost Reduction

Through this DOE funded 3.5-year research project, feasibility of fabricating supercritical carbon dioxide (sCO2) turbine components by powder metallurgy (PM) based near-net-shape (NNS) hot isostatic pressing (HIP) was demonstrated in a turbine nozzle ring, a turbine casing with Haynes 282 powder, and a bimetallic pipe with Haynes 282 and SS415 powder. As-HIP microstructure of various powders and HIP processing conditions was studied to downselect a condition for the prototype components. Tensile strength and low cycle fatigue (LCF) capability of PM HIP 282 was found to be superior to cast 282, despite a debit in creep stress capability that could be mitigated by component design modification. Near-Net-shape with minimal post machining was achieved by modeling the non-uniform shrinkage during HIP cycle and designing the HIP tooling to meet dimensional targets. The prototypes of turbine nozzle ring and bimetallic pipe were successful in achieving overall dimension, microstructure, and properties, despite dimensional tolerance affected by chemical milling rate. The prototype of a 1700lbs turbine casing was partially successful in achieving dimension, microstructure in as-HIP state, and providing consistent mechanical properties, however, cracking issue during post heat treatment required further investigation. The estimated manufacturing cost using NNS HIP was a ~50% reduction compared to forging with extensive machining, which translated into ~$100/kWe CAPEX cost reduction for concentrated solar power (CSP) power block.

14 SOLAR ENERGY↗

DOE OSTI2024

Enhancement of Conjugated Polymer Microstructure and Mixed-Conducting Properties via Chalcogenophene Heteroatom Substitution

Heteroatom substitution is a powerful tool to tune the intra- and intermolecular structure of conjugated polymers as well as their resulting optoelectronic and electrochemical properties. Here, a series of oligoethylene glycol bithiophene chalcogenophene polymers (p(g3T2-X)) with systematically varied furan, thiophene, selenophene, and tellurophene comonomers have been synthesized for mixed ionic-electronic conducting applications. Their microstructures have been thoroughly characterized ex situ and in situ with X-ray scattering, and their mixed conducting properties have been probed in electrochemical transistor testbeds. Chalcogenophene heteroatom choice was found to clearly dictate the polymer microstructure (crystallite dimensionality and orientation) and tune mixed conducting properties. Proceeding down Group 16, from O to Se systematically directed the molecular ordering of 2D polymer crystallites from face-on (O) to mixed (S) to edge-on (Se) orientations, with Te driving the polymer to form well-oriented edge-on 3D crystallites. Heteroatom dictated crystallite quality, and orientation tuned relative ionic transport by 2 orders of magnitude. Hole mobility (μ hole ) and mixed conducting figure of merit (μC*) were each tuned over an order of magnitude depending on heteroatom choice, with the Te-containing polymer reaching μ hole = 3.60 cm 2 V –1 s –1 and μC* = 483 F cm –1 V –1 s –1 , due to improved molecular ordering. Insights from this polymer series highlight target microstructures for enhanced mixed conduction in future conjugated polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2018

Simulation Kinetics of Austenitic Phase Transformation in Ti+Nb Stabilized IF and Microalloyed Steels

In the present study, the influence of cooling rates (low to ultrafast) on diffusion controlled and displacive transformation of Ti-Nb IF and microalloyed steels has been thoroughly investigated. Mechanisms of nucleation and formation of non-equiaxed ferrite morphologies (i.e., acicular ferrite and bainitic ferrite) have been analyzed in details. The continuous cooling transformation behavior has been studied in a thermomechanical simulator (Gleeble 3800) using the cooling rates of 1-150 °C/s. On the basis of the dilatometric analysis of each cooling rate, continuous cooling transformation (CCT) diagrams have been constructed for both the steels to correlate the microstructural features at each cooling rate in different critical zones. In the case of the IF steel, massive ferrite grains along with granular bainite structures have been developed at cooling rates > 120 °C/s. On the other hand, a mixture of lath bainitic and lath martensite structures has been formed at a cooling rate of ~ 80 °C/s in the microalloyed steel. A strong dependence of the cooling rates and C content on the microstructures and mechanical properties has been established. The steel samples that were fast cooled to a mixture of bainite ferrite and martensite showed a significant improvement of impact toughness and hardness (157 J, for IF steel and 174 J for microalloyed steel) as compared to that of the as-received specimens (133 J for IF steel and 116 J for microalloyed steel). Thus, it can be concluded that the hardness and impact toughness properties are correlated well with the microstructural constituents as indicated by the CCT diagram. Transformation mechanisms and kinetics of austenitic transformation to different phase morphologies at various cooling rates have been discussed in details to correlate microstructural evolution and mechanical properties.

36 MATERIALS SCIENCE↗

NASA NTRS2012

Fatigue Failure Modes of the Grain Size Transition Zone in a Dual Microstructure Disk

Mechanical property requirements vary with location in nickel-based superalloy disks. In order to maximize the associated mechanical properties, heat treatment methods have been developed for producing tailored grain microstructures. In this study, fatigue failure modes of a grain size transition zone in a dual microstructure disk were evaluated. A specialized heat treatment method was applied to produce varying grain microstructure in the bore to rim portions of a powder metallurgy processed nickel-based superalloy disk. The transition in grain size was concentrated in a zone of the disk web, between the bore and rim. Specimens were extracted parallel and transversely across this transition zone, and multiple fatigue tests were performed at 427 C and 704 C. Grain size distributions were characterized in the specimens, and related to operative failure initiation modes. Mean fatigue life decreased with increasing maximum grain size, going out through the transition zone. The scatter in limited tests of replicates was comparable for failures of uniform gage specimens in all transition zone locations examined.

Gabb, Timothy P.↗

NASA NTRS1993

Thermal spray forming of refractory sample ampoule cartridges for single crystal growth space furnaces

A thermal spray process is being used to build up refractory metals and ceramics into a containment cartridge for high temperature, single crystal semiconductor growth experiments. This process uses high energy plasma inside a low pressure (100-200 torr) inert environment to apply layers of material onto a removable mandrel. A variety of materials are being characterized and evaluated against a demanding set of requirements, including high service temperature (1700 C), oxidation resistance, and resistance to liquid metal attack. Techniques to spray form refractory metals (tungsten, molybdenum, niobium, tantalum) and ceramics (alumina, boron nitride) are being developed in the Plasma Spray Cell at Marshall Space Flight Center. These plasma spray formed materials have been evaluated for mechanical properties, density, microstructure, and resistance to liquid metal attack. Forming techniques and the resultant mechanical and metallurgical properties will be presented.

Zimmerman, Frank↗

NASA NTRS1993

Thermal spray forming of refractory sample ampoule cartridges for single crystal growth space furnaces

Zimmerman, Frank↗

NASA NTRS1991

Ultrasonic evaluation of oxidation and reduction effects on the elastic behavior and global microstructure of YBa2Cu3O7-x

Ultrasonic velocity measurement techniques were used to evaluate the effects of oxidation and reduction on the elastic properties, global microstructure and oxygen content of the YBa2Cu3O(7-x) ceramic superconductor for samples ranging from 70 to 90 pct. of theoretical density. Bulk density, velocity, and elastic modulus generally increased with increasing oxygen content upon oxidation, and this behavior was reversible. Velocity image patterns were similar after oxidation and reduction treatments for a 90 pct. dense sample, although the velocity value at any given point on the sample was changed following the treatments. The unchanging pattern correlated with destructive measurements showing that the spatial pore distribution (fraction and size) was not measurably altered after the treatments. Changes in superconducting behavior, crystal structure, and grain structure were observed consistent with changes in oxygen content.

Roth, Don J.↗

DOE OSTI2023

Denoising diffusion algorithm for inverse design of microstructures with fine-tuned nonlinear material properties

Here we introduce a denoising diffusion algorithm to discover microstructures with nonlinear fine-tuned properties. Denoising diffusion probabilistic models are generative models that use diffusion-based dynamics to gradually denoise images and generate realistic synthetic samples. By learning the reverse of a Markov diffusion process, we design an artificial intelligence to efficiently manipulate the topology of microstructures to generate a massive number of prototypes that exhibit constitutive responses sufficiently close to designated nonlinear constitutive behaviors. To identify the subset of microcstructures with sufficiently precise fine-tuned properties, a convolutional neural network surrogate is trained to replace high-fidelity finite element simulations to filter out prototypes outside the admissible range. Results of this study indicate that the denoising diffusion process is capable of creating microstructures of fine-tuned nonlinear material properties within the latent space of the training data. More importantly, this denoising diffusion algorithm can be easily extended to incorporate additional topological and geometric modifications by introducing high-dimensional structures embedded in the latent space. Numerical experiments are conducted on the open-source mechanical MNIST data set (Lejeune, 2020). Consequently, this algorithm is not only capable of performing inverse design of nonlinear effective media, but also learns the nonlinear structure–property map to quantitatively understand the multiscale interplay among the geometry, topology, and their effective macroscopic properties.

42 ENGINEERING↗

DOE OSTI2019

Early Career: In-situ Monitoring of Dynamic Phenomena during Solidification

Solidification is critical to processes like casting and additive manufacturing and the manufacture of metallic alloy components we use in our everyday lives. State-of-the-art characterization techniques, now available at U.S. DOE User Facilities and in the laboratory, are not only enabling fundamental studies of metallic alloy solidification dynamics, but also in-operando, in-situ deformation, and manufacturing studies. Here we use x-ray, proton, and electron imaging to study solidification dynamics from the micro-scale to the macro-scale, at times ranging from microseconds to minutes. Our experimental results are used to inform, develop, and validate computational models at the same length and time-scales. Integrating in-situ characterization and modeling will yield the prediction and control of metallic alloy solidification dynamics and the creation of microstructures and properties by design with advanced manufacturing. Major research accomplishments during this period include: 1. Exploring dynamical microstructure selection by means of real-time synchrotron x-ray imaging of controlled directional solidification of aluminum alloys and quantitative phase field modeling. 2. In-situ and ex-situ electron microscopy of rapid solidification after laser melting of metallic alloys. 3. Exploring the impact of microstructural heterogeneities that develop during solidification on solid-state phase transitions, with an emphasis on phase growth, (meta)stability, and transition pathways in aluminum alloys. 4. Demonstrations of four-dimensional (three-dimensions plus time) x-ray microscopy during controlled directional solidification and the first quasi-static/dynamic transmission high energy electron microscopy of metallic alloy solidification dynamics. 5. Experiments and modeling of solidification structure evolution and forward modeling and testing of micromechanical behavior.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Solidification pattern, microstructure and texture development in Laser Powder Bed Fusion (LPBF) of Al10SiMg alloy

Highlights: • The complex solidification pattern during Laser Powder Bed Fusion of Al10SiMg alloy is explained. • The evolution of α-Al cellular network, grain structure and texture development is characterized. • The grain structure is shown to be columnar throughout the printed sample • The grains’ orientation align with that of the α-Al cells. • The size evolution of α-Al cells and grains within the scan tracks follow opposite patterns. • Utilizing of a 67° hatch angle enhances densification and promotes a more isotropically developed texture across the build. - Abstract: A comprehensive analysis of solidification patterns and microstructural development is presented for an Al10SiMg sample produced by Laser Powder Bed Fusion (LPBF). Utilizing a novel scanning strategy that involves counter-clockwise rotation of the scan vector by 67° upon completion of each layer, a relatively randomized cusp-like pattern of protruding/overlapping scan tracks has been produced along the build direction. We show that such a distribution of scan tracks, as well as enhancing densification during LPBF, reduces the overall crystallographic texture in the sample, as opposed to those normally achieved by commonly-used bidirectional or island-based scanning regimes with 90° rotation. It is shown that, under directional solidification conditions present in LPBF, the grain structure is strictly columnar throughout the sample and that the grains' orientation aligns well with that of the α-Al cells. The size evolution of cells and grains within the melt pools, however, is shown to follow opposite patterns. The cells'/grains' size distribution and texture in the sample are explained via use of analytical models of cellular solidification as well as the overall heat flow direction and local solidification conditions in relation to the LPBF processing conditions. Such a knowledge of the mechanisms upon which microstructural features evolve throughout a complex solidification process is critical for process optimization and control of mechanical properties in LPBF.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Utilizing machine learning to predict tensile ductility and yield strength of CoNiV-based multi-principal elements alloys

This study explores the use of machine learning (ML) as a computational tool to accelerate the design of multi-principal element alloys (MPEAs) with improved tensile elongation. An ML model was trained using available experimental data from the literature along with theoretically derived features to predict yield strength (YS) and ductility. A subset of ML-predicted compositions—CoNiVFe, CoNiVTi, CoNiVTiFe, and CoCrNiVTi—was synthesized and evaluated through tensile testing. The ML model underpredicted YS by approximately 20–30 % and overpredicted ductility by 60–70 % for Ti-containing alloys. Microstructural analysis revealed that Ti segregation at interdendritic regions contributed to early fracture, leading to discrepancies in ductility predictions. Ti segregation at these regions likely drives the increased YS due to segregation strengthening. In contrast, the CoNiVFe alloy showed good agreement with both experimental YS and elongation, with prediction errors of ∼10.2 % and ∼20.7 %, respectively. Microstructural characterization revealed minimal segregation in this alloy, suggesting that the ML model can reliably predict the properties of alloys with little to no segregation. These findings highlight the capability of ML in predicting YS with good accuracy but underscore its limitations in capturing defect-driven failure mechanisms such as segregation-induced embrittlement.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Report on the Integration of Experimental and Modeling Data for Initial Equivalence Study of Mechanical Performance in Irradiated LPBF 316 Stainless Steel

To ensure the rapid development, deployment, and use of advanced nuclear technologies, faster qualification approaches are needed. Typically, the primary pathway uses traditional data packages consistent with the American Society of Mechanical Engineers Boiler and Pressure Vessel Code, which does not consider the environmental effects the material will experience such as corrosion and radiation damage. Examining radiation effects requires a significant amount of space in US facilities at the Advanced Test Reactor and the High Flux Isotope Reactor (HFIR) and suffers from natural gradients in temperature and neutron flux profiles. Ion irradiation may enable rapid assessment of radiation-induced damage to a material and is proposed as part of an accelerated materials qualification framework through the Advanced Materials and Manufacturing Technologies program. To enhance the utility of ion irradiation as an examination tool, this report provides the initial assessment of engineering-relevant properties of microstructures produced from ion irradiation in the near-surface volume. Nanoindentation, Vickers hardness, and known tensile properties were brought together with simple mathematical models and experimental data for an initial equivalence study of the mechanical performance of irradiated laser powder bed fusion (LPBF) 316 stainless steels across length scales. Direct observation of the calculated ion irradiation yield stress and measured neutron irradiation yield stress at 2 dpa showed that both datasets exhibit the same trend with irradiation temperature and overlap within an acceptable band of stress values. Ion irradiations at 10 dpa serve as a prediction of properties to compare to postirradiation examination of HFIR-irradiated LPBF 316H further in the program. This work is a significant demonstration of the Licensing Approach with Ions and Neutrons, which uses ion irradiations to generate mechanical property information more rapidly than through neutron irradiations.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Understanding the Effect of Electron Beam Melting Scanning Strategies on the Aluminum Content and Materials State of Single Ti-6Al-4V Feedstock

Research on the additive manufacturing of metals often neglects any characterization of the composition of final parts, erroneously assuming a compositional homogeneity that matches the feedstock material. Here, the composition of electron-beam-melted Ti-6Al-4V produced through three distinct scanning strategies (linear raster and two point melting strategies, random fill and Dehoff fill) is characterized both locally and globally through energy-dispersive spectroscopy and quantitative chemical analysis. As a result of the different scanning strategies used, differing levels of preferential vaporization occur across the various parts, leading to distinct final compositions, with extremes of ~5.8 wt.% Al and ~4.8 wt.% Al. In addition, energy-dispersive spectroscopy composition maps reveal specific features in both the XY and XZ planes (with Z being the build direction) as a result of local inhomogeneous preferential vaporization. The subsequent change in composition significantly modifies the materials’ state of parts, wherein parts and local regions with higher aluminum contents lead to higher hardness levels (with a ~50 HV difference) and elastic property values and vice versa. While varying scan strategies and scan parameters are known to modify the microstructure and properties of a part, the effect on composition cannot, and should not, be neglected.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Critical statistical assessment of data in metal additive manufacturing

Obtaining high quality data reflecting the relationships between the additive manufacturing (AM) process parameters, material microstructure and mechanical properties is crucial for the use of machine learning in AM. A database of over 4,000 data entries of metal AM was created thanks to a large number of literature studies on key process parameters and indicators of build quality. Meta-analysis reveals critical biases in the literature. Firstly, majority of studies report only high quality builds, these imbalances in reporting result in weak correlation between process parameters, properties and consolidation, limiting the ability of machine learning models to generalize beyond optimized conditions. Nevertheless, the trained models accurately predict yield strength ($R^2 = 0.85$), suggesting that certain process–property relationships are effectively captured within these models. Secondly, quantitative microstructural data are largely absent, limiting the learning of the microstructure-mechanical properties relationships. Finally, current process window identification is based largely on the consolidation, despite significant uncertainty in its measurement. It is important to identify the process map on the basis of not only the consolidation, but also mechanical behaviour under loading. Such a identification shows that 316 L and Inconel have much larger process map (i.e. highly printable) in comparison to the AlSi10Mg and Ti6Al4V.

Additive manufacturing↗

NASA NTRSDate not supplied

Metallic Powder Core Tubular Wire (PCTW) Development for Additive Manufacturing

NASA Langley Research Center (LaRC) in Hampton, VA, and the Center for Welding, Joining, and Coating Research (CWJCR) in the Department of Metallurgical and Materials Engineering at the Colorado School of Mines (CSM) in Golden, CO, have collaborated for nearly fifteen years to develop metallic powder core tubular wire (PCTW) feedstock for additive manufacturing (AM) using electron beam deposition. The motivation for this development was to offset dealloying observed during deposition of titanium and aluminum alloy solid wire feedstock in the LaRC electron beam freeform fabrication (EBF3) system and to explore novel alloy compositions by tailoring the powder fill. EBF3 is a fusion-based AM process that is performed under vacuum and is consequently prone to vaporization loss of low vapor pressure alloying elements. Research spanning four graduate student research projects succeeded in developing the basic methodology to fabricate PCTW, the mass balance equations used to define the powder fill, microstructure control through particulate inoculation, and the feasibility of producing metal matrix composite materials. Metallic PCTW is comprised of a thin foil sheath wrapped around a powder blend. Fabrication of PCTW at CSM was accomplished using a tubular wire mill system to first bend a flat strip into a u-shaped cross section, deposit a powder fill, create a lap joint to seal the wire, and draw to final diameter. Powder management systems were developed to ensure uniform mixing of powder constituents and identify feed rates for optimum fill ratios. Processing parameters were successfully developed for titanium and aluminum alloy sheaths to account for material work hardening during drawing. Mass balance equations were developed to account for compositional contributions of the sheath and powder fill. PCTW composition can be adjusted through selection of the sheath or powder materials. PCTWs were successfully developed to offset Al loss in deposits of Ti-6-4 and Mg loss in Al 6061, resulting in deposits that were within the composition limits for each material. Ti-6-4 deposits were fabricated using PCTW comprised of commercially pure (CP) titanium sheath and a fill of pre-alloyed Ti-6-4 powder with additions of elemental Al and V powders. Additions of both elements were required to account for the CP Ti from the sheath, and Al was further enhanced to offset documented losses in EBF3 deposits. For Al 6061 deposits, composition was modulated through the choice of sheath material. The PCTW was made using an Al 5052 sheath to supplement Mg content and a fill composition of pre-alloyed 6061 powder with additions of Si and Cu.The slower solidification rate of the EBF3 process compared with laser powder bed fusion processes can lead to coarse-grained microstructures and mechanical property anisotropy. EBF3deposits of Ti-6-4 exhibited large epitaxially grown β grains, which result in degraded mechanical properties in the deposition direction. Microstructure refinement was achieved through a combination of electron beam modulation and the use of a PCTW designed for Ti-6-4 deposits and modified by the addition of powder made from Fe and B. Resulting deposits exhibited reductions in β grain size, α phase colony intercept length and lath width, and an increased volume fraction of β phase. The mechanism of microstructure refinement was related to precipitation of boride particles. Hardness testing confirmed that mechanical property anisotropy was reduced and an overall increase in hardness was achieved.Metal matrix composite (MMC) materials offer strength and stiffness benefits over unreinforced materials. Two methods were investigated using PCTW technology for producing Al 6061 basedMMC materials; the direct addition of SiC reinforcing particles and the in-situ generation of reinforcements through reaction synthesis of precursor powders. Al 6061 based MMCs reinforced with SiC exhibited particle clustering and formation of aluminum carbides during deposition. The application of a Ni coating to the SiC particles prior to incorporation into the powder fill eliminated aluminum carbide formation and aided particle distribution during deposition. Modulation of beam focus and power further reduced aluminum carbide formation and aided particle distribution. In reaction synthesis, precursor additions undergo an exothermic reaction during deposition to form new ceramic products, generally of finer scale than the initial precursor components. The product phases provide reinforcement in the MMC and act as nucleation sites during solidification, resulting in grain refinement, improved mechanical properties, and reduced susceptibility to solidification cracking. Higher tensile strength and stiffness were demonstrated in Al 6061 based MMCs with 2 vol% reinforcement. These combined research efforts demonstrate the potential of PCTW technology for customizing of alloy composition and achieving microstructure control. A manufacturing process for titanium- and aluminum-based PCTWs was developed based on iterative design, theoretical calculations, and empirical data. PCTW technology successfully mitigated Al loss from Ti-6-4 and Mg loss in Al 6061, resulted in grain refinement in Ti-6-4, and demonstrated fabrication of Al based MMCs

Marcia S Domack↗

DOE OSTI2021

Mechanical rolling and annealing of wire-arc additively manufactured stainless steel plates

Thin walls of 304L stainless steel were fabricated by wire-arc additive manufacturing (WAAM) followed by post build thermomechanical processing to modify the as built microstructure and properties. The walls were made using a high-deposition-rate robotically controlled gas-metal arc welding system and were characterized using optical microscopy and tensile tested for mechanical properties. Post processing consisted of mechanical rolling the walls to 25% and 40% strains, followed by annealing at 1050°C to demonstrate a wide range of properties. Results show that WAAM can be used to build custom sized semi-finished parts or blanks that can later be thermomechanically processed to increase strength and ductility through recrystallization of the as built microstructure, and/or processed into desired shapes with improved mechanical properties.

304L stainless steel↗

DOE OSTI2018

Quenching and Partitioning Process Development to Replace Hot Stamping of High Strength Automotive Steel

The present project investigated Quenching and Partitioning (Q&P) to process cold rolled steels to develop high strength sheet steels that exhibit superior ductility compared to available grades with the intent to allow forming of high strength parts at room temperature to provide an alternative to hot stamping of parts. Hot stamping of boron alloyed steel is the current technology to manufacture thinner gauge sections in automotive structures to guarantee anti-intrusion during collisions whilst improving fuel efficiency by decreasing vehicle weight. Hot stamping involves reheating steel to 900 °C or higher followed by deformation and quenching in the die to produce ultra-high strength materials. Hot stamping requires significant energy to reheat the steel and is less productive than traditional room temperature stamping operations. Stamping at elevated temperature was developed due to the lack of available steels with strength levels of interest possessing sufficient ductility enabling traditional room temperature forming. This process is seeing growing demand within the automotive industry and, given the reheating step in this operation, increased energy consumption during part manufacturing results. The present research program focused on the development of steel grades via Q&P processing that exhibit high strength and formability enabling room temperature forming to replace hot stamping. The main project objective consisted of developing sheet steels exhibiting minimum ultimate tensile strength levels of 1200 MPa in combination with minimum tensile elongation levels of 15 pct using Q&P processing through judicious alloy design and heat treating parameter definition. In addition, detailed microstructural characterization and study of properties, processing and microstructure interrelationships were pursued to develop strategies to further enhance tensile properties. In order to accomplish these objectives, alloy design was conducted towards achieving the target properties. Twelve alloys were designed and laboratory produced involving melting, alloying, casting, hot rolling, and cold rolling to obtain sheet steels of approximately 1 mm thickness. Q&P processing of the samples was then conducted. Target properties were achieved and substantially exceeded demonstrating success in the developed and employed alloy design approaches. The best combinations of tensile properties were found at approximately 1550 MPa with a total elongation in excess of 20 pct clearly showing the potential for replacement of hot stamping to produce advanced high strength steels.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Prediction of shock initiation thresholds and ignition probability of polymer-bonded explosives using mesoscale simulations

The design of new materials requires establishment of macroscopic measures of material performance as functions of microstructure. Traditionally, this process has been an empirical endeavor. In this paper, an approach to computationally predict the probabilistic ignition thresholds of polymer-bonded explosives (PBXs) using mesoscale simulations is developed. The simulations explicitly account for microstructure, constituent properties, and interfacial responses and capture processes responsible for the development of hotspots and damage. The specific mechanisms tracked include viscoelasticity, viscoplasticity, fracture, post-fracture contact, frictional heating, and heat conduction. The probabilistic analysis uses sets of statistically similar microstructure samples to directly mimic relevant experiments for quantification of statistical variations of material behavior due to inherent material heterogeneities. The particular thresholds and ignition probabilities predicted are expressed in James type and Walker–Wasley type relations, leading to the establishment of explicit analytical expressions for the ignition probability as function of loading. Specifically, the ignition thresholds corresponding to any given level of ignition probability and ignition probability maps are predicted for PBX 9404 for the loading regime of U p = 200–1200 m/s where U p is the particle speed. The predicted results are in good agreement with available experimental measurements. A parametric study also shows that binder properties can significantly affect the macroscopic ignition behavior of PBXs. Finally, the capability to computationally predict the macroscopic engineering material response relations out of material microstructures and basic constituent and interfacial properties lends itself to the design of new materials as well as the analysis of existing materials.

36 MATERIALS SCIENCE↗