Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

High-Pressure Neutron Diffraction Study on H-D Isotope Effects in Brucite

A neutron powder diffraction study of hydrogenated and deuterated brucite was conducted at ambient temperature and at pressures to 9 GPa, using a Paris-Edinburgh high-pressure cell at the WAND instrument of ORNL High Flux Isotope Reactor. The two materials were synthesized by the same method and companion measurements of neutron diffraction were conducted under the same conditions. Our refinement results show that the lattice-parameters of the a axis, parallel to the sheets of Mg-O octahedra, decreases only slightly with pressure with no effect of H-D substitution. However, the c axis of Mg(OD)2 is shorter and decreases more rapidly than that of Mg(OH)2 with increasing pressure. Consequently, the unit-cell volume of deuterated brucite is slightly, but systematically smaller than that of normal brucite, which were fitted to third-order Birch-Murnaghan equation: K0=41.46 0.52 and 39.04 0.30 GPa for Mg(OH)2 and Mg(OD)2, respectively with a fixed K0 value of 10. Our results suggest that H-D substitution of brucite and other hydrous minerals with H-bonding likely influences their structural and dynamic properties under pressure, including the position of hydrogen atoms. The measured effect of H-D substitution on the unit-cell volume also demonstrates that brucite (and other hydrous minerals) preferentially incorporate deuterium over hydrogen under pressure, suggesting that the distribution of hydrogen isotopes in deep-earth conditions may differ significantly from that in near-surface environments.

08 HYDROGEN↗

Effect of Stepwise Pressure Change on Porosity Evolution during Directional Solidification in Small Cylindrical Channels

Controlled directional solidification experiments were performed in capillary channels, using nitrogen-saturated succinonitrile, to examine the effect of an in-situ stepwise processing pressure increase on an isolated pore evolution. Two experiments were performed using different processing pressure input profiles. The results indicate that a processing pressure increase has a transient effect on pore growth geometry characterized by an initial phase of decreasing pore diameter, followed by a recovery phase of increasing pore diameter. The experimental results also show that processing pressure can be used as a control parameter to either increase or terminate porosity formation. A theoretical model is introduced which indicates that the pore formation process is limited by the diffusion of solute-gas through the melt, and that the observed response toa pressure increase is attributed to the re-equilibration of solute concentration in the melt associated with the increased melt pressure.

Grugel, R.N.↗

Electron and ion kinetics in three-dimensional confined microwave-induced microplasmas at low gas pressures

The effects of the gas pressure (p{sub g}), microcavity height (t), Au vapor addition, and microwave frequency on the properties of three-dimensional confined microwave-induced microplasmas were discussed in light of simulation results of a glow microdischarge in a three-dimensional microcavity (diameter d{sub h} = 1000 μm) driven at constant voltage loading on the drive electrode (V{sub rf}) of 180 V. The simulation was performed using the PIC/MCC method, whose results were experimentally verified. In all the cases we investigated in this study, the microplasmas were in the γ-mode. When p{sub g} increased, the maximum electron (n{sub e}) or ion density (n{sub Ar+}) distributions turned narrow and close to the discharge gap due to the decrease in the mean free path of the secondary electron emission (SEE) electrons (λ{sub SEE-e}). The peak n{sub e} and n{sub Ar+} were not a monotonic function of p{sub g}, resulting from the two conflicting effects of p{sub g} on n{sub e} and n{sub Ar+}. The impact of ions on the electrode was enhanced when p{sub g} increased. This was determined after comparing the results of ion energy distribution function (IEDFs) at various p{sub g}. The effects of t on the peaks and distributions of n{sub e} and n{sub Ar+} were negligible in the range of t from 1.0 to 3.0 mm. The minimum t of 0.6 mm for a steady glow discharge was predicted for p{sub g} of 800 Pa and V{sub rf} of 180 V. The Au vapor addition increased the peaks of n{sub e} and n{sub Ar+}, due to the lower ionization voltage of Au atom. The acceleration of ions in the sheaths was intensified with the addition of Au vapor because of the increased potential difference in the sheath at the drive electrode.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Combined effects of gas pressure and exciting frequency on electron energy distribution functions in hydrogen capacitively coupled plasmas

The combined effects of the variation of hydrogen pressure (40-400 mTorr) and exciting frequency (13.56-50 MHz) on the electron energy probability function (EEPF) and other plasma parameters in capacitively coupled hydrogen H{sub 2} discharge at fixed discharge voltage were investigated using rf-compensated Langmuir probe. At a fixed exciting frequency of 13.56 MHz, the EEPF evolved from Maxwellian-like distribution to a bi-Maxwellian distribution when the H{sub 2} pressure increased, possibly due to efficient vibrational excitation. The electron density largely increased to a peak value and then decreased with the increase of H{sub 2} pressure. Meanwhile, the electron temperature and plasma potential significantly decrease and reaching a minimum at 120 mTorr beyond, which saturated or slightly increases. On the other hand, the dissipated power and electron density markedly increased with increasing the exciting frequency at fixed H{sub 2} pressure and voltage. The electron temperatures negligibly dependent on the driving frequency. The EEPFs at low pressure 60 mTorr resemble Maxwellian-like distribution and evolve into a bi-Maxwellian type as frequency increased, due to a collisonless (stochastic) sheath-heating in the very high frequency regime, while the EEPF at hydrogen pressure {>=}120 mTorr retained a bi-Maxwellian-type distribution irrespective of the driving frequency. Such evolution of the EEPFs shape with the driving frequency and hydrogen pressure has been discussed on the basis of electron diffusion processes and low threshold-energy inelastic collision processes taking place in the discharge. The ratio of stochastic power to bulk power heating ratio is dependent on the hydrogen pressure while it is independent on the driving frequency.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Magnetic and magnetocaloric properties of Ni-Mn-Cr-Sn Heusler alloys under the effects of hydrostatic pressure

The magnetic, thermal, and magnetocaloric properties of Ni 45 Mn 43 CrSn 11 Heusler alloy have been investigated using differential scanning calorimetry and magnetization with hydrostatic pressure measurements. A shift in the martensitic transition temperature (T M ) to higher temperatures was observed with the application of pressure. The application of pressure stabilizes the martensitic state and demonstrated that pressure can be a parameter used to control and tune the martensitic transition temperature (the temperature where the largest magnetocaloric effect is observed). The magnetic entropy change significantly decreases from 33 J/kg K to 16 J/kg K under the application of a hydrostatic pressure of 0.95 GPa. The critical field of the direct metamagnetic transition increases, whereas the initial susceptibility (dM/dH) in the low magnetic field region drastically decreases with increasing pressure. Thus, the relevant parameters that affect the magnetocaloric properties are discussed.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Testing the Effects of Helium Pressurant on Thermodynamic Vent System Performance with Liquid Hydrogen

In support of the development of a zero gravity pressure control capability for liquid hydrogen, testing was conducted at the Marshall Space Flight Center using the Multipurpose Hydrogen Test Bed (MHTB) to evaluate the effects of helium pressurant on the performance of a spray bar thermodynamic vent system (TVS). Fourteen days of testing was performed in August - September 2005, with an ambient heat leak of about 70-80 watts and tank fill levels of 90%, 50%, and 25%. The TVS successfully controlled the tank pressure within a +/- 3.45 kPa (+/- 0.5 psi) band with various helium concentration levels in the ullage. Relative to pressure control with an "all hydrogen" ullage, the helium presence resulted in 10 to 30 per cent longer pressure reduction durations, depending on the fill level, during the mixing/venting phase of the control cycle. Additionally, the automated control cycle was based on mixing alone for pressure reduction until the pressure versus time slope became positive, at which time the Joule-Thomson vent was opened. Testing was also conducted to evaluate thermodynamic venting without the mixer operating, first with liquid then with vapor at the recirculation line inlet. Although ullage stratification was present, the ullage pressure was successfully controlled without the mixer operating. Thus, if vapor surrounded the pump inlet in a reduced gravity situation, the ullage pressure can still be controlled by venting through the TVS Joule Thomson valve and heat exchanger. It was evident that the spray bar configuration, which extends almost the entire length of the tank, enabled significant thermal energy removal from the ullage even without the mixer operating. Details regarding the test setup and procedures are presented in the paper. 1

Flachbart, R. H.↗

Cost-Effective Additive Manufacturing of Ambient Pressure-Dried Silica Aerogel

The conventional manufacturing processes for aerogel insulation materials mostly rely on the supercritical drying, which suffers from issues of massive energy consumption, high-cost equipment, and prolonged processing time. Considering the large market demand for the aerogel insulation material in the next decade, a cost-effective and scalable fabrication technique is highly desired. In this paper, a direct ink writing (DIW) method is used to three-dimensionally fabricate the silica aerogel insulation material, followed by room-temperature and ambient pressure drying. Compared with the supercritical drying and freeze-drying techniques, the reported method significantly reduces the fabrication time and costs. The cost-effective DIW technique offers the capability to print complex hollow internal structures, coupled with the porous aerogel structure, it is found to be beneficial for the thermal insulation property. In this work, the addition of fiber to the ink assures the durability of the fabricated product, without sacrificing the thermal insulation performance. The foam ink preparation methods and the printability are demonstrated in this paper, along with the printing of complex three-dimensional geometries. The thermal insulation performance of the printed objects is characterized, and the mechanical properties were also examined. The proposed approach is found to have a 56% reduction in the processing time. The printed silica aerogels exhibit a low thermal conductivity of 0.053 W m –1 K –1 .

36 MATERIALS SCIENCE↗

Preliminary Data on the Effects of Inlet Pressure Distortions on the J57-P-1 Turbojet Engine

An investigation to determine the steady-state and surge characteristics of the J57-P-1 two-spool turbojet engine with various inlet air-flow distortions was conducted in the altitude wind tunnel at the NACA Lewis laboratory. Along with a uniform inlet total-pressure distribution, one circumferential and three radial pressure distortions were investigated. Data were obtained over a complete range of compressor speeds both with and without intercompressor air bleed at a flight Mach number of 0.8 and at altitudes of 35,000 and 50,000 feet. Total-pressure distortions of the magnitudes investigated had very little effect on the steady-state operating line for either the outer or inner compressor. The small radial distortions investigated also had engine over that obtained with the uniform inlet pressure distribution. The circumferential distortion, however, raised the minimum speed at which the engine could operate without encountering surge when the intercompressor bleeds were closed. This increase in minimum speed resulted in a substantial reduction in the operable speed range accompanied by a reduction in the altitude operating limit.

Wallner, Lewis E.↗

Pressurizing Field-Effect Transistors of Few-Layer MoS 2 in a Diamond Anvil Cell

Hydrostatic pressure applied using diamond anvil cells (DAC) has been widely explored to modulate physical properties of materials by tuning their lattice degree of freedom. Independently, electrical field is able to tune the electronic degree of freedom of functional materials via, for example, the field-effect transistor (FET) configuration. Combining these two orthogonal approaches would allow discovery of new physical properties and phases going beyond the known phase space. Such experiments are, however, technically challenging and have not been demonstrated. In this paper, we report a feasible strategy to prepare and measure FETs in a DAC by lithographically patterning the nanodevices onto the diamond culet. Multiple-terminal FETs were fabricated in the DAC using few-layer MoS 2 and BN as the channel semiconductor and dielectric layer, respectively. It is found that the mobility, conductance, carrier concentration, and contact conductance of MoS 2 can all be significantly enhanced with pressure. Finally, we expect that the approach could enable unprecedented ways to explore new phases and properties of materials under coupled mechano-electrostatic modulation.

36 MATERIALS SCIENCE↗

Stress anisotropy and concentration effects in high pressure measurements

Sodium chloride is used as an internal pressure standard in high pressure research. Possible corrections are discussed which are needed in the calibration of this standard due to the independent effects of stress anisotropy and stress concentration in pressure vessels. The first is due to the lack of a truly hydrostatic state of stress in solid state pressure vessels. The second is due to the difference in the compressibilities between the pressure transmitting substances (sodium chloride) and a stiffer test specimen. These two corrections are then combined and a total correction, as a function of measured pressure, is discussed for two systems presently in use. The predicted value of the combined effect is about 5-10% of the pressure at 30 GPa.

Nelson, D. A., Jr.↗

Numerical-heating effects in atmospheric pressure streamer discharges simulated with a PIC code

Artificial heating in plasma simulations is a well-known phenomenon which occurs when, among other things, the Debye length is poorly resolved by the simulation mesh. Here, in this work, the degree to which numerical-heating occurs during a simulation of a nanosecond atmospheric pressure streamer discharge is examined. The streamer is simulated using a two-dimensional finite-element, particle-in-cell code Empire, which uses direct simulation Monte Carlo for binary particle interactions. Initially, an estimate of the numerical-heating rate applied to Empire is performed using a simple plasma model. Second, a positive atmospheric pressure streamer discharge simulation is performed to study the effects of numerical heating on plasma density, electron temperature, and streamer velocity. The nominal Debye length is approximately 1 μm and the amount of numerical heating introduced in the simulation is varied by using mesh sizes ranging from 2 μm to 20 μm. A measurable numerical heating quantity is proposed that can be used to estimate the appropriate element size and quantify the numerical-heating that can be expected over the simulation time for an atmospheric pressure streamer. In conclusion while Δx/λ D violations can be an issue it is not likely to be an issue with streamer discharges that are temporally short and occur in environments where collision frequencies are high. This result validates the rationale of grid size choices for a large amount of previously published works where Δx/λ D violation was not clearly addressed. Primary finding of this work is that numerical heating is of minor concern for plasma simulations where electron–neutral collisions are numerous such that multiple collisions can occur within a single plasma period.

Nikic, Dejan [University of New Mexico, Albuquerqu↗

Turbulent boundary layer in an adverse pressure gradient without effect of wall curvature

The hypersonic compressible turbulent boundary layer in an adverse pressure gradient along a cylindrical axisymmetric body was studied. The tests were conducted in a Mach 6 contoured axisymmetric nozzle. An external compression cowl was used to produce the gradual adverse pressure gradient and a maximum pressure rise of 7 times the freestream static pressure was achieved in a test region of 23 cm. Boundary layer profiles of static pressure, total pressure, and total temperature, as well as wall transient heat transfer rates were measured. Comparisons of the velocity total temperature profiles to linear and quadratic relations were made. Measured heat transfer data were in good agreement with the prediction from the flat-plate reference enthalpy method. Integral parameters were also in good agreement with results of numerical solutions for compressible turbulent boundary layer equations.

Zakkay, V.↗

Combined effect of chemical pressure and valence electron concentration through the electron-deficient Li substitution on the RE{sub 4}LiGe{sub 4} (RE=La, Ce, Pr, and Sm) system

Four members of the RE{sub 4}LiGe{sub 4} (RE=La, Ce, Pr, and Sm) system have been prepared by high-temperature reaction method and characterized by X-ray diffractions. All compounds crystallize in the orthorhombic Gd{sub 5}Si{sub 4}-type structure (space group Pnma, Pearson code oP16) with bonding interactions for interslab Ge{sub 2} dimers. The Li substitution for rare-earth elements in the RE{sub 4}LiGe{sub 4} system leads to a combined effect of the increased chemical pressure and the decreased valance electron concentration (VEC), which eventually results in the structure transformation from the Sm{sub 5}Ge{sub 4}-type with all broken interslab Ge–Ge bond for the parental RE{sub 5}Ge{sub 4} to the Gd{sub 5}Si{sub 4}-type structure for the ternary RE{sub 4}LiGe{sub 4} (RE=La, Ce, Pr, and Sm) system. Site-preference between rare-earth metals and Li is proven to generate energetically the most favorable atomic arrangements according to coloring-problem, and the rationale is provided using both the size-factor and the electronic-factor related, respectively, to site-volume and electronegativity as well as QVAL values. Tight-binding, linear-muffin-tin-orbital (TB-LMTO) calculations are performed to investigate electronic densities of states (DOS) and crystal orbital Hamilton population (COHP) curves. The influence of reduced VEC for chemical bonding including the formation of interslab Ge{sub 2} dimers is also discussed. The magnetic property measurements prove that the non-magnetic Li substitution leads to the ferromagnetic (FM)-like ground state for Ce{sub 4}LiGe{sub 4} and the co-existence of antiferromagntic (AFM) and FM ground states for Sm{sub 4}LiGe{sub 4}. - Graphical abstract: Reported is a combined effect of the chemical pressure and the reduced VEC caused by the smaller monovalent non-magnetic Li substitution for the larger trivalent magnetic rare-earth metals in the RE{sub 4}LiGe{sub 4} (RE=La, Ce, Pr, and Sm) system. This results in the structure transformation from the Sm{sub 5}Ge{sub 4}-type to the Gd{sub 5}Si{sub 4}-type structure and the changes in magnetic properties. Display Omitted - Highlights: • Four Li-containing intermetallic compounds RE{sub 4}LiGe{sub 4} (RE=La, Ce, Pr and Sm) were synthesized. • The combined effect of the chemical pressure and the reduced VEC caused by Li substitution for a rare-earth metal results in the structure transformation. • Electronic structures and magnetic properties of title compounds were thoroughly investigated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of Effects of Inlet Pressure Losses on Performance of Axial-Flow Type Turbojet Engine

The experimentally determined performance characteristics of an axial-flow turbojet engine have been used to estimate the effects of inlet total-pressure losses on net thrust and specific fuel consumption at a constant engine speed. At low altitudes and flight Mach numbers, inlet pressure losses cause an increase in engine discharge temperature and it is possible that the maximum allowable turbine temperature maybe exceeded. An inlet absolute total-pressure loss of 10 percent will result in a thrust loss of 14 percent and a 15-percent increase in specific fuel consumption based on net thrust. At high altitudes and flight Mach numbers, choking conditions exist in the exhaust nozzle and the inlet pressure losses do not affect the discharge temperatures. Under these conditions, a 10-percent loss in inlet absolute total pressure produces a 22-percent loss in net thrust and a 16-percent increase in specific fuel consumption. If the exhaust-nozzle-outlet area is adjusted to compensate for the effect of inlet losses on discharge temperature in the nonchoking cases (low altitude and Mach numbers), the thrust and fuel consumption will be changed in a manner similar to the results obtained in the choking cases.

Sanders, Newell D↗

Effects of chamber pressure variation on the grid temperature in an inertial electrostatic confinement device

Inertial electrostatic confinement fusion devices are compact sources of neutrons, protons, electrons, and x rays. Such sources have many applications. Improving the efficiency of the device also increases the applications of this device. Hence a thorough understanding of the operation of this device is needed. In this paper, we study the effect of chamber pressure on the temperature of the cathode. Experimentally, the grid temperature decreases as the chamber pressure increases; numerical simulations suggest that this is caused by the reduction of the hot ion current to the cathode as the pressure increases for constant power supply current. Such an understanding further supports the conclusion that the asymmetric heating of the cathode can be decreased by homogenizing the ion flow around the cathode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗