Search NASA⌕ Search

SEARCH · Search NASA

Results for “elastic modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Young's modulus evaluation of high burnup structure in UO 2 with nanometer resolution

The mechanical properties of a well-characterized irradiated light water reactor fuel pin with an average burnup of 72 MWd/kgU were investigated by utilizing nano-indentation technique. Young's modulus and hardness are reported as functions of radial positions covering from mid radial position in the urania pellet to high burnup structure, fuel-cladding chemical interaction zone and zirconium-based cladding. Here, by probing microstructure of the high burnup zone, the mechanical properties of sub-grains and the interaction between them were examined at the nanometer scale. Force-displacement curves from each of these individual sub-grains suggest they resemble single crystal UO 2 . However, these restructured grains are weakly bonded to their neighbors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of a High-Pressure Fuel Injection System for Use with Propane-DME

Paper details the design approach and performance of a high-pressure common rail fuel injection system used with Propane-DME mixtures targeting high injection pressures on a light duty 2.2L inline-4 compression ignition engine. The study estimates the bulk modulus of elasticity based on the hardware geometry and operating pressures to assess the compressibility of Propane and DME across a range of pressures typical of the LD engine application. The compressibility factor ranges from 500 to 3000 bar, significantly lower than the theoretical values for the conditions tested. The high-pressure pump performance is optimized via the implementation of an inlet metering valve operated on a crank-angle open/close sequence to control pressure at the common rail. The application of a model-based controller and the use of high-speed sampling of rail pressure indicate that pressure at the rail can be attained with the pump metering valve, and without use of the pressure relieve valve present in the rail. Results show a significant reduction on pumping work parasitics and of fuel heating, on the order of 40°C, at typical working conditions with the proposed approach. Injector rates of injection with Propane-DME are very similar to those of Diesel. Paper compares bench data of rates of injection versus simulation predictions across operating pressures of 200 to 1000bar and from injection commands spanning 0.20 to 2.0ms. Furthermore, the accuracy of the model predictions are attributed in part by to the updated fuel compressibility modulus descriptions attained during the testing.

42 ENGINEERING↗

Reassessing early-age strength development of high-volume fly ash concretes for precast buildings

Increasing beneficial use of fresh or landfilled fly ash as a replacement for Portland cement can be more challenging for the construction of precast buildings or similar applications requiring rapid strength development. Therefore, the framework presented in this paper aims to reassess high-volume fly ash concretes but in the context of facilitating more sustainable precast buildings. More specifically, the framework was used to characterize strength development of concrete mixes with a target minimum 24-hour compressive strength of 24.1 MPa (3500 psi), selected as an example strength development metric to demonstrate the framework, and comprised of 40% Class C, Class F, and landfilled (harvested) fly ash – as a high-volume replacement of Type III or Type IL cement. High-early strength was driven by optimized dosages of commercial grade gypsum and accelerating admixtures, in addition to optimal aggregate packing and mix proportioning strategies. Early-age mechanical properties including compressive strength, modulus of rupture, and modulus of elasticity were reevaluated within 24 hours of batching with respect to common precast production demands. Simple data analyses were then used to highlight cases where currently accepted design provisions for the aforementioned properties are either overly-conservative or unconservative with respect to test data. Furthermore, the framework and demonstration of example mixes presented herein aim to promote confidence for using larger fractions of fresh or landfilled fly ashes for precast buildings to further enhance environmental benefits without sacrificing pertinent early-age structural performance.

42 ENGINEERING↗

Brittle Fracture of 2D MoSe 2

An in situ quantitative tensile testing platform is developed in this paper to enable the uniform in-plane loading of a freestanding membrane of 2D materials inside a scanning electron microscope. The in situ tensile testing reveals the brittle fracture of large-area MoSe 2 crystals and measures their fracture strength for the first time.

36 MATERIALS SCIENCE↗

Hemp-Fiber-Reinforced Unsaturated Polyester Composites: Optimization of Processing and Improvement of Interfacial Adhesion

The processing variables for making hemp-fiber-reinforced unsaturated polyester (UPE) composites were optimized through orthogonal experiments. It was found that the usage of initiator, methyl ethyl ketone peroxide, had the most significant effect on the tensile strength of the composites. The treatment of hemp fibers with a combination of 1, 6-diisocyanatohexane (DIH) and 2-hydroxylethyl acrylate (HEA) significantly increased tensile strength, flexural modulus of rupture and flexural modulus of elasticity, and water resistance of the resulting hemp-UPE composites. FTIR spectra revealed that DIH and HEA were covalently bonded to hemp fibers. Scanning electronic microscopy graphs of the fractured hemp-UPE composites demonstrated that treatment of hemp fibers with a combination of DIH and HEA greatly improved the interfacial adhesion between hemp fibers and UPE. The mechanism of improving the interfacial adhesion is proposed.

1,6-diisocyanatohexane↗

Development of high‐performance partially biobased thermoset polyester using renewable building blocks from isosorbide, 1,3‐propanediol, and fumaric acid

Abstract Research on biobased thermoset resins has been overlooked when compared with the rapid progress on biobased thermoplastics. The objective of this work was to develop unsaturated polyester prepolymers based on building blocks derived from renewable raw materials, namely, biobased isosorbide, 1,3‐propanediol, and fumaric acid, with petroleum‐derived phthalic anhydride. The prepolymers developed herein behaved as low‐molecular weight macromolecules (oligoesters), with M n varying between 1.2 and 1.5 kDa, but achieved a high bio‐content of up to 87.1 wt%. The prepolymers were incorporated into reactive diluents comprising a blend of 2‐hydroxyethyl methacrylate and styrene, formulated to be eco‐friendlier and less toxic than typical styrene‐only incorporation approach, thus resulting in resins with viscosities between 750 and 950 cP. These resins are suitable for use in various fiber‐reinforced polymer production techniques, such as manual lamination, vacuum infusion, and pultrusion, having the benefit of presenting over 50 wt% of bio‐content in some formulations. Moreover, the crosslinked polyester resins (thermosets) exhibit comparable mechanical and thermomechanical behavior to their petrochemical‐based counterparts, with modulus of elasticity and tensile strength of up to 3.9 GPa and 62.1 MPa, respectively, and glass transition temperatures of up to 106°C, making them greener alternatives for high‐performance structural applications.

Hofmann, Mateus↗

Material selection and manufacturing for high‐temperature heat exchangers: Review of state‐of‐the‐art development, opportunities, and challenges

Abstract Many energy systems demand heat transfer at high temperatures to keep up with high demand for power, so high‐temperature material that can perform and last under these harsh conditions is needed for heat exchangers. The engineering requirements for these high‐temperature heat exchanger material call for high thermal conductivity, high resistance to fracture, high resistance to creep deformation, environmental stability in environments associated with the application, and high modulus of elasticity while maintaining low cost to make and maintain. Naturally, ceramics are a good solution for this endeavor. In the past, high‐temperature heat exchangers made from ceramics have been used. We provide examples of ceramics in relevant heat exchange applications and provide motivation where additive manufacturing (AM) can improve efficiency. AM for the relevant material is under development, and we provide insight on the AM of ceramic materials and examples of AM heat exchangers keeping cost in mind. The motivation of the review paper is to provide a framework for material and manufacturing selection for high‐temperature heat exchangers for AM to keep up with the demand for better efficiency, better material, better manufacturing, and cost moving forward with AM technology in high‐temperature ceramic heat exchangers.

36 MATERIALS SCIENCE↗

Rigidity of poly-L-glutamic acid scaffolds: Influence of secondary and supramolecular structure

Poly-L-glutamic acid (PGA) is a widely used biomaterial, with applications ranging from drug delivery and biological glues to food products and as a tissue engineering scaffold. A biodegradable material with flexible conjugation functional groups, tunable secondary structure, and mechanical properties, PGA has potential as a tunable matrix material in mechanobiology. Some recent studies in proteins connecting dynamics, nanometer length scale rigidity, and secondary structure suggest a new point of view from which to analyze and develop this promising material. Our paper characterizes the structure, topology, and rigidity properties of PGA prepared with different molecular weights and secondary structures through various techniques including scanning electron microscopy, FTIR, light, and neutron scattering spectroscopy. On the length scale of a few nanometers, rigidity is determined by hydrogen bonding interactions in the presence of neutral species and by electrostatic interactions when the polypeptide is negatively charged. Finally, when probed over hundreds of nanometers, the rigidity of these materials is modified by long range intermolecular interactions that are introduced by the supramolecular structure.

36 MATERIALS SCIENCE↗

Defoliation‐induced compensatory transpiration is compromised in SUT4 ‐RNAi Populus

Abstract The tonoplast sucrose transporter PtaSUT4 is well expressed in leaves of Populus tremula × Populus alba (INRA 717‐IB4), and its inhibition by RNA‐interference (RNAi) alters leaf sucrose homeostasis. Whether sucrose partitioning between the vacuole and the cytosol is modulated by PtaSUT4 for specific physiological outcomes in Populus remains unexplored. In this study, partial defoliation was used to elicit compensatory increases in photosynthesis and transpiration by the remaining leaves in greenhouse‐grown poplar. Water uptake, leaf gas exchange properties, growth and nonstructural carbohydrate abundance in source and sink organs were then compared between wild‐type and SUT4 ‐RNAi lines. Partial defoliation increased maximum photosynthesis rates similarly in all lines. There was no indication that source leaf sugar levels changed differently between wild‐type and RNAi plants following partial defoliation. Sink levels of hexose (glucose and fructose) and starch decreased similarly in all lines. Interestingly, plant water uptake after partial defoliation was not as well sustained in RNAi as in wild‐type plants. While the compensatory increase in photosynthesis was similar between genotypes, leaf transpiration increased less robustly in RNAi than wild‐type plants. SUT4‐RNAi and wild‐type source leaves differed constitutively in their bulk modulus of elasticity, a measure of leaf turgor, and storage water capacitance. The data demonstrate that reduced sucrose partitioning due to PtaSUT4 ‐RNAi altered turgor control and compensatory transpiration capacity more strikingly than photosynthesis and sugar export. The results are consistent with the interpretation that SUT4 may control vacuolar turgor independently of sink carbon provisioning.

54 ENVIRONMENTAL SCIENCES↗

Urea Formaldehyde and Cellulose Nanocrystals Adhesive: Studies Applied to Sugarcane Bagasse Particleboards

The aim of this research was to investigate the behavior of urea formaldehyde (UF) adhesive based particleboards using sugarcane bagasse (SCB), with and without the addition of cellulose nanocrystals (NCC). In the first step of this research study, the interaction between UF and the NCC was evaluated. The NCC were dispersed in the UF, in different proportions (0, 0.5, 1, 2, 3 and 5%). Subsequent to this, the mixtures were dried, milled, and put in molds, to produce flexural specimens. The second step involved evaluation of the interaction between the NCC, UF, and SCB. After sonication, the NCC and UF were applied on the SCB particles to produce particleboards. They were evaluated according to the modulus of elasticity and rupture, water absorption (WA), and thickness swelling. The viscosity of the mixture of NCC and UF increased according to the NCC increase load. At 5% of NCC load, the viscosity increased greatly, which prevented adhesive dispersion in the particleboard. The thermogravimetric analysis of UF showed that better conditions of processing were at 160 °C for 8 min, so these parameters were used to produce the specimens. SCB is a promising raw material for particleboard, and its potential to produce SCB particleboards with relatively good performance was demonstrated. For the particleboards specimens, the best performance was observed with 1% of NCC. Particleboards did not show improvement compared with UF specimens, probably because bond links were not sufficient. Addition of NCC in UF increased the liquid suspension viscosity, and the specimens showed a better mechanical performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Natural and Accelerated Aging on the Mechanical Performance of a Composite Based on Recycled Multilayer Carton

A composite elaborated from waste material was studied for its proposed use as a wood plastic composite. Multilayer food cartons and recycled high density polyethylene were used for the elaboration of laminates, in a proportion of 55% and 45% volume fraction, respectively. The samples were subjected to an aging in an accelerated weathering (AW) chamber for 0, 500, 1000 and 2000 h with UVB radiation, temperature and humidity cycles. Samples exposed to natural weathering (NW) for 0, 1300, 2600 and 5200 h, in a warm sub-humid environment were also studied, the aim being to elucidate a correlation of the useful lifespan of the material. In both cases, after the exposure, three-point bend tests were performed to evaluate the effect on the mechanical properties. The analysis of the degradation process was carried out by infrared spectroscopy, indicating that the AW and NW samples showed deterioration of the material in different proportions. By mean of thermal analysis, it was possible to associate the degradation with the appearance and/or growth of the endothermic peaks, showing a variation in the melting temperature as the time of exposure to AW and NW increased, resulting in a change in the crystallinity percentage. The modulus of rupture (MOR) and the flexural modulus of elasticity decreased by 20% in samples subjected to AW for 2000 h; while in the samples exposed to NW, required of 5200 h to obtain a reduction of 16% in the MOR.

36 MATERIALS SCIENCE↗

Nonlinear viscoelastic response of silicone additively manufactured direct ink write (DIW) foams under repetitive compression

To investigate dynamic fatigue behavior of foam in military protective applications, such as helmets, additively manufactured (AM) foams were compressively strained into the plateau region using a reduced design of experiments. A simple power law was found to govern the decline in dynamic stiffness (complex modulus) as the foams underwent the purchase order requirement of 10,000 cycles of small deformation in the plateau region. This rate of decline was newly found to correlate with the degree of nonlinearity in the material’s deformation, quantified using total harmonic distortion. Materials with low nonlinearity exhibited relatively stable stiffness across cycles, while those with high nonlinearity experienced greater losses. The observed nonlinearity depended on both applied stress and strain rate. A strong linear correlation (R 2 = 0.78) was identified between second-order nonlinearity and the time-dependent stiffness response. Two lattice structures were examined: face-centered tetragonal (FCT) and simple cubic (SC). The SC material exhibited higher total harmonic distortion (5%) and lower stiffness retention than the FCT (2%). In conclusion, these results suggest that for cyclic compression applications in a wide variety of industries such as packaging, personal protective equipment, or aerospace, selecting materials with lower stress and greater structural uniformity can enhance the stability of dynamic performance.

42 ENGINEERING↗

New titanium(IV) coordination compounds with 2-hydroxybenzyl alcohol derivatives used in the preparation of ultra-high molecular weight polyethylene

A reaction of 2,4-bis(α,α-dimethylbenzyl)phenol with TiCl{sub 2}(ОPr{sup i})2 and Ti(ОPr{sup i}){sub 4} was used to obtain the coordination compounds (HL){sub 2}L{sub 2}Ti{sub 2}Cl{sub 2}•MeC{sub 6}H{sub 5} and L{sub 4}Ti{sub 4}(OPr{sup i}){sub 8}, respectively. The compounds were characterized by elemental analysis, NMR spectroscopy, and X-ray diffraction. The titanium(IV) coordination compounds obtained polymerize ethylene in the presence of binary cocatalysts {3Et_2AlCl + Bu_2Mg} or {3Et_3Al_2Cl_3 + Bu_2Mg} at moderate to high rates, giving rise to ultra-high molecular weight polyethylene with a wide range of molecular masses. The highest values of tensile strength (2.4 GPa) and modulus of elasticity (ε = 2.67%) were obtained for the sample with a molecular mass of 3.14•10{sup 6} Da under comparable conditions of orientation drawing of the film filaments. This sample was obtained when complex (HL)2L{sub 2}Ti{sub 2}Cl{sub 2} was activated by a 3: 1 mixture of Et{sub 2}AlCl—Bu{sub 2}Mg.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A cell wall-bound anionic peroxidase, PtrPO21, is involved in lignin polymerization in Populus trichocarpa

Class III peroxidases are members of a large plant-specific sequence-heterogeneous protein family. Several sequence-conserved homologs have been associated with lignin polymerization in Arabidopsis thaliana, Oryza sativa, Nicotiana tabacum, Zinnia elegans, Picea abies, and Pinus sylvestris. In Populus trichocarpa, a model species for studies of wood formation, the peroxidases involved in lignin biosynthesis have not yet been identified. To do this, we retrieved sequences of all PtrPOs from Peroxibase and conducted RNA-seq to identify candidates. Transcripts from 42 PtrPOs were detected in stem differentiating xylem (SDX) and four of them are the most xylem-abundant (PtrPO12, PtrPO21, PtrPO42, and PtrPO64). PtrPO21 shows xylem-specific expression similar to that of genes encoding the monolignol biosynthetic enzymes. Using protein cleavage-isotope dilution mass spectrometry, PtrPO21 is detected only in the cell wall fraction and not in the soluble fraction. Downregulated transgenics of PtrPO21 have a lignin reduction of ~20% with subunit composition (S/G ratio) similar to wild type. The transgenics show a growth reduction and reddish color of stem wood. The modulus of elasticity (MOE) of the stems of the downregulated PtrPO21-line 8 can be reduced to ~60% of wild type. Differentially expressed gene (DEG) analysis of PtrPO21 downregulated transgenics identified a significant overexpression of PtPrx35, suggesting a compensatory effect within the peroxidase family. No significant changes in the expression of the 49 P. trichocarpa laccases (PtrLACs) were observed.

09 BIOMASS FUELS↗

Laser Nitriding of the Newly Developed Ti-20Nb-13Zr at.% Biomaterial Alloy to Enhance Its Mechanical and Corrosion Properties in Simulated Body Fluid

Despite the widespread application of Ti alloy in the biomedical field, surface treatments are typically applied to improve its resistance to corrosion and wear. A newly developed biomedical Ti-20Nb-13Zr at.% alloy (TNZ) was laser-treated in nitrogen environment to improve its surface characteristics with corrosion protection performance. Surface modification of the alloy by laser was performed through a Nd:YAG laser. The structural and surface morphological alterations in the laser nitrided layer were investigated by XRD and a FE-SEM. The mechanical properties have been evaluated using nanoindentation for laser nitride and as-received samples. The corrosion protection behavior was estimated using electrochemical corrosion analysis in a physiological medium (SBF). The obtained results revealed the production of a dense and compact film of TiN fine grains (micro-/nanosize) with 9.1 µm below the surface. The mechanical assessment results indicated an improvement in the modulus of elasticity, hardness, and resistance of the formed TiN layer to plastic deformation. The electrochemical analysis exhibited that the surface protection performance of the laser nitrided TNZ substrates in the SBF could be considerably enhanced compared to that of the as-received alloy due to the presence of fine grains in the TiN layer resulting from laser nitriding. Furthermore, the untreated and treated Ti-20Nb-13Zr alloy exhibited higher corrosion resistance than the CpTi and Ti6Al4V commercial alloys. The improvements in the surface hardness and corrosion properties of Ti alloy in a simulated body obtained using laser nitriding make this approach a suitable candidate for enhancing the properties of biomaterials.

36 MATERIALS SCIENCE↗

Assessing Mechanical Behaviors of Additive Manufactured Alternating Layers of Inconel-718/H13 Tool Steel

An H 13 (high-strength, low-ductility) tool steel die will fail due to compressive high cycle fatigue. If the die is manufactured by direct metal deposition and layered with Inconel-718 (low-strength, high-ductility), it may impact the mechanical properties of the material. Hardness tests, micro-tensile tests, and micro-compression tests were used to analyze the mechanical properties of this additive manufactured layered metal while observing real-time morphology changes on the surface. Energy dispersive spectroscopy was also performed to determine where failure tended to occur within the Inconel-718 material. The hardness was lower than expected, as was the ultimate tensile strength, yield strength, modulus of elasticity, and strain at failure. Each tensile test failed within the Inconel-718 layer. In conclusion, a sample designed to have a single thin middle layer of Inconel-718 sandwiched by H 13 enabled the visual recording of crack initiation and propagation under a tensile load using a confocal scanning laser microscope.

36 MATERIALS SCIENCE↗