Search NASA⌕ Search

SEARCH · Search NASA

Results for “impulse test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Damping in coupled bending and torsion - An experiment

Traditional experimental modal testing methods are used to determine the damping properties of a Euler-Bernoulli beam with offset inertial tip mass. Both viscous and strain rate damping models are considered in bending and in torsion. A partial differential equation model of the coupled system is used. Eigenfunctions are derived for the coupled system by using a Green's function approach to derive the approximate uncoupled eigenfunctions. These eigenfunctions are used in a decoupled fashion with experimental modal data to estimate the damping parameters of the coupled system. The experimental modal data were obtained from both free and impulse responses using a combined translational and rotational accelerometer.

Umland, Jeffrey W.↗

Study of noise on a small-scale hovering tilt rotor

A study of the noise from a small-scale, semi-span test of a hovering tilt rotor is presented. The effect on noise of the tilt rotor fountain and of several tilt rotor configuration changes is examined. Measurments were made of an isolated rotor; rotor and wing; rotor and image plane; and rotor, wing and image plane. This last configuration models a tilt rotor. With a tilt rotor, the wing turns some of the rotor downwash inboard. When the flows meet, some of the flow is forced upward creating a fountain. Some of the fountain is ingested into the rotor disc. Rotor fountain interactions produce very unsteady impulsive noise to the rear of the aircraft. Configuration changes to investigate download reduction included increasing the rotor/wing separation, deflecting the flap, adding the nacelle, adding vortex trapping plates and blowing on the upper surface. These configuration changes produced little or no effect on the noise, although they changed the net download. Increasing the wing span, however, reduced the annoying content of this impulse noise about 2dB.

Mosher, Marianne↗

A long-life bipropellant system demonstration: Viking Orbiter Propulsion System - 4 years in space and operating

On April 23, 1980, Viking Orbiter One (VO-1), operating in the blowdown mode, completed a ten second Mars orbit trim maneuver to position the spacecraft for its final science sequence in May-June 1980. This brought the number of propulsive maneuvers for VO-1 to 23. Total accumulated operating time for the rocket engine was 2896 seconds, representing a total impulse of 3.93 x 10 to the 6th N-sec. The estimated propellant remaining was sufficient to operate the rocket engine for an additional 30 seconds. VO-1 has completed more than 1700 days in space, 1400 days in orbit around Mars and more than two years of attitude control system operation with helium gas transferred from the propulsion system pressurant tank. The mass of helium remaining is expected to be sufficient for attitude control through June 1980. This paper presents the flight history of the Viking 75 Orbiter Propulsion Systems and summarizes the design and test philosophy which have contributed to their success.

Schmit, D. D.↗

Xenon ion propulsion for orbit transfer

For more than 30 years, NASA has conducted an ion propulsion program which has resulted in several experimental space flight demonstrations and the development of many supporting technologies. Technologies appropriate for geosynchronous stationkeeping, earth-orbit transfer missions, and interplanetary missions are defined and evaluated. The status of critical ion propulsion system elements is reviewed. Electron bombardment ion thrusters for primary propulsion have evolved to operate on xenon in the 5 to 10 kW power range. Thruster efficiencies of 0.7 and specific impulse values of 4000 s were documented. The baseline thruster currently under development by NASA LeRC includes ring-cusp magnetic field plasma containment and dished two-grid ion optics. Based on past experience and demonstrated simplifications, power processors for these thrusters should have approximately 500 parts, a mass of 40 kg, and an efficiency near 0.94. Thrust vector control, via individual thruster gimbals, is a mature technology. High pressure, gaseous xenon propellant storage and control schemes, using flight qualified hardware, result in propellant tankage fractions between 0.1 and 0.2. In-space and ground integration testing has demonstrated that ion propulsion systems can be successfully integrated with their host spacecraft. Ion propulsion system technologies are mature and can significantly enhance and/or enable a variety of missions in the nation's space propulsion program.

Rawlin, V. K.↗

Planned In-Space Electric Propulsion Experiments

Ion Propulsion provides an order of magnitude improvement, relative to chemical on-board propulsion systems, of specific impulse at the cost of a relatively small increase in propulsion system dry mass. For civilian space craft, ion propulsion technology provides the potential for increased performance and reduced cost for planetary spacecraft and for large satellites in geostationary orbit. For military applications ion propulsion offers significant benefits for station keeping and repositioning satellites in geostationary orbit. NASA has begun to validate ion propulsion technology for applications to which 2.5 kW to 5.0 kW ion thrusters would be appropriate. NASA's validation program, called NSTAR (NASA SEP Technology Application Readiness), consists of two major elements: a ground test element and an in-space experiment. The Ground Test Element will validate the life, integrability, and performance of low-power ion propulsion. The In-Space Element will demonstrate the ability to integrate and fly an ion propulsion system. As an experiment, it will measure the interactions between the ion propulsion system, the host spacecraft, and the surrounding space plasma; and it will provide a quantitative assessment of the ability of ground testing to replicate the in-space performance of ion thrusters. By involving industry in this program, a commercial source for this technology will be assured. Further, the successful completion of the NSTAR validation program will stimulate commercial and government (both civilian and military) uses of this technology.

ion propulsion planetary spacecraft geostationary ↗

Revealing the Formation of the <20 MeV Inner Proton Radiation Belt at L ∼ 2 During the 10–11 May 2024 Superstorm

A new proton radiation belt was identified during the geomagnetic superstorm of 10–11 May 2024. To investigate its origin, we use an MHD-test particle simulation to model solar energetic proton (SEP) trapping and the evolution of the initial trapped proton population during the storm. The simulation weights the injected SEP population with interplanetary proton measurements and the initial trapped proton radial profile with energy-resolved Weather System Follow-on-Microwave (WSF-M) proton data, enabling quantitative comparison with observations. Results show that SEP contributions are minimal; the new ∼2–18 MeV belt at L ∼ 2 forms mainly through redistribution and energization of the initial trapped population within hours of the CME shock, driven by subsequent electric field impulses, rather than the initial shock alone. These results provide quantitative evidence based on realistic, plasma-dependent field dynamics and significantly advance understanding of inner radiation belt formation.

79 ASTRONOMY AND ASTROPHYSICS↗

Small Reactor Designs Suitable for Direct Nuclear Thermal Propulsion (Interim Report)

Advancement of U.S. scientific, security, and economic interests requires high performance propulsion systems to support missions beyond low Earth orbit. A robust space exploration program will include robotic outer planet and crewed missions to a variety of destinations including the moon, near Earth objects, and eventually Mars. Past studies, in particular those in support of both the Strategic Defense Initiative (SDI) and the Space Exploration Initiative (SEI), have shown nuclear thermal propulsion systems provide superior performance for high mass high propulsive delta-V missions. In NASA's recent Mars Design Reference Architecture (DRA) 5.0 study, nuclear thermal propulsion (NTP) was again selected over chemical propulsion as the preferred in-space transportation system option for the human exploration of Mars because of its high thrust and high specific impulse (~900 s) capability, increased tolerance to payload mass growth and architecture changes, and lower total initial mass in low Earth orbit. The recently announced national space policy supports the development and use of space nuclear power systems where such systems safely enable or significantly enhance space exploration or operational capabilities. An extensive nuclear thermal rocket technology development effort was conducted under the Rover/NERVA, GE-710 and ANL nuclear rocket programs (1955-1973). Both graphite and refractory metal alloy fuel types were pursued. The primary and significantly larger Rover/NERVA program focused on graphite type fuels. Research, development, and testing of high temperature graphite fuels was conducted. Reactors and engines employing these fuels were designed, built, and ground tested. The GE-710 and ANL programs focused on an alternative ceramic-metallic 'cermet' fuel type consisting of UO 2 (or UN) fuel embedded in a refractory metal matrix such as tungsten. The General Electric program examined closed loop concepts for space or terrestrial applications as well as open loop systems for direct nuclear thermal propulsion. Although a number of fast spectrum reactor and engine designs suitable for direct nuclear thermal propulsion were proposed and designed, none were built. This report summarizes status results of evaluations of small nuclear reactor designs suitable for direct nuclear thermal propulsion.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Xenon ion propulsion for orbit transfer

The status of critical ion propulsion system elements is reviewed. Electron bombardment ion thrusters for primary propulsion have evolved to operate on xenon in the 5-10 kW power range. Thruster efficiencies of 0.7 and specific impulse values of 4000 s have been documented. The baseline thruster currently under development by NASA LeRC includes ring-cusp magnetic field plasma containment and dished two-grid ion optics. Based on past experience and demonstrated simplifications, power processors for these thrusters should have approximately 500 parts, a mass of 40 kg, and an efficiency near 0.94. Thrust vector control, via individual thruster gimbals, is a mature technology. High pressure, gaseous xenon propellant storage and control schemes, using flight qualified hardware, result in propellant tankage fractions between 0.1 and 0.2. In-space and ground integration testing has demonstrated that ion propulsion systems can be successfully integrated with their host spacecraft.

Rawlin, V. K.↗

Voyager spacecraft attitude control propulsion system post-launch performance requirements changes

A test program aimed at the re-qualification of the 0.2-lbf attitude control thruster of the Voyager 2 spacecraft was carried out while the spacecraft was in flight on an interplanetary trajectory to Uranus. The objective of the program was to determine if the 0.2-lbf thruster could be successfully and repeatedly fired at pulse widths of less than the standard minimum pulse width of 10 milliseconds with no degradation. It was demonstrated that the thruster was qualified for short pulse operation at pulse widths of 4 ms or greater. Pulse widths of 4.0 ms provide an impulse bit of approximately 45 percent of the impulse provided by a 10-ms pulse, and the pulse-to-pulse and unit-to-unit variation is approximately plus or minus 10 percent.

Groudle, T. A.↗

Periodic Time-Domain Nonlocal Nonreflecting Boundary Conditions for Duct Acoustics

Periodic time-domain boundary conditions are formulated for direct numerical simulation of acoustic waves in ducts without flow. Well-developed frequency-domain boundary conditions are transformed into the time domain. The formulation is presented here in one space dimension and time; however, this formulation has an advantage in that its extension to variable-area, higher dimensional, and acoustically treated ducts is rigorous and straightforward. The boundary condition simulates a nonreflecting wave field in an infinite uniform duct and is implemented by impulse-response operators that are applied at the boundary of the computational domain. These operators are generated by convolution integrals of the corresponding frequency-domain operators. The acoustic solution is obtained by advancing the Euler equations to a periodic state with the MacCormack scheme. The MacCormack scheme utilizes the boundary condition to limit the computational space and preserve the radiation boundary condition. The success of the boundary condition is attributed to the fact that it is nonreflecting to periodic acoustic waves. In addition, transient waves can pass rapidly out of the solution domain. The boundary condition is tested for a pure tone and a multitone source in a linear setting. The effects of various initial conditions are assessed. Computational solutions with the boundary condition are consistent with the known solutions for nonreflecting wave fields in an infinite uniform duct.

Watson, Willie R.↗

Free radical propulsion concept

A free radical propulsion concept utilizing the recombination energy of dissociated low molecular weight gases to produce thrust was examined. The concept offered promise of a propulsion system operating at a theoretical impulse, with hydrogen, as high as 2200 seconds at high thrust to power ratio, thus filling the gas existing between chemical and electrostatic propulsion capabilities. Microwave energy used to dissociate a continuously flowing gas was transferred to the propellant via three body recombination for conversion to propellant kinetic energy. Power absorption by the microwave plasma discharge was in excess of 90 percent over a broad range of pressures. Gas temperatures inferred from gas dynamic equations showed much higher temperatures from microwave heating than from electrothermal heating. Spectroscopic analysis appeared to corroborate the inferred temperatures of one of the gases tested.

Hawkins, C. E.↗

H2 arcjet performance mapping program

Work performed during the period of Mar. 1991 to Jan. 1992 is reviewed. High power H2 arcjets are being considered for electric powered orbit transfer vehicles (EOTV). Mission analyses indicate that the overall arcjet thrust efficiency is very important since increasing the efficiency increases the thrust, and thereby reduces the total trip time for the same power. For example, increasing the thrust efficiency at the same specific impulse from 30 to 40 percent will reduce the trip time by 25 percent. For a 200 day mission, this equates to 50 days, which results in lower ground costs and less time during which the payload is dormant. Arcjet performance levels of 1200 seconds specific impulse (lsp) at 35 to 40 percent efficiency with lifetimes over 1000 hours are needed to support EOTV missions. Because of the potential very high efficiency levels, the objective of this program was to evaluate the ability of a scaled Giannini-style thruster to achieve the performance levels while operating at a reduced nominal power of 10 kW. To meet this objective, a review of past literature was conducted; scaling relationships were developed and applied to establish critical dimensions; a development thruster was designed with the aid of the plasma analysis model KARNAC and finite element thermal modeling; test hardware was fabricated; and a series of performance tests were conducted in RRC's Cell 11 vacuum chamber with its null-balance thrust stand.

Source record↗

Raising Nuclear Thermal Propulsion (NTP) Technology Readiness Above 3

NTP development is currently supported by the NASA program office "Advanced Exploration Systems". The concept is a main propulsion option being considered for human missions to Mars in the 2030's. Major NTP development took place in the 1960's and 1970's under the Rover/NERVA program. The technology had matured to TRL 6 and was preparing to go to TRL 7 with a prototype flight engine before the program was cancelled. Over the last 40 years, a variety of continuations started, but only lasted a few years each. The Rover/NERVA infrastructure is almost all gone. The only remains are a few pieces of hardware, final reports and a few who worked the Rover/NERVA. Two types of nuclear fuel are being investigated to meet the current engine design specific impulse of 900 seconds compared to approximately 850 seconds demonstrated during Rover/NERVA. One is a continuation of composite fuel with new coatings to better control mid-band corrosion. The other type is a CERMET fuel made of Tungsten and UO2. Both fuels are being made from Rover/NERVA lessons learned, but with slightly different recipes to increase fuel endurance at higher operating temperatures. The technology readiness level (TRL) of these current modified reactor fuels is approximately TRL 3. To keep the development cost low and help mature the TRL level past 4 quickly, a few special non-nuclear test facilities have been made to test surrogate fuel, with depleted uranium, as coupons and full length elements. Both facilities utilize inductive heating and are licensed to handle depleted uranium. TRL 5 requires exposing the fuel to a nuclear environment and TRL 6 requires a prototype ground or flight engine system test. Currently, three different NTP ground test facility options are being investigated: exhaust scrubber, bore hole, and total exhaust containment. In parallel, a prototype flight demonstration test is also being studied. The first human mission to Mars in the 2030's is currently 2033. For an advanced propulsion concept to be seriously considered for use, the engine development plans need to show it is feasible and affordable to reach TRL 8 by 2027 and can be qualified for human mission use.

Gerrish, Harold P., Jr.↗

Status of xenon ion propulsion technology

This paper describes a working-model xenon ion propulsion subsystem (XIPS) designed for north-south stationkeeping (NSSK) of 2500-kg-class geosynchronous communication satellites. The XIPS consists of a 25-cm-diameter laboratory-model thruster, a breadboard-model power supply, and a flight-prototype pressure regulator (the critical component of the pressure-regulated xenon feed system). With a thrust of 63.5 mN, specific impulse of 2800 sec, and thruster efficiency of 65 percent, the XIPS performance is believed to be the highest ever reported for an ion thruster operated at 1.3-kW input power. The XIPS power supply accepts an input power of about 1.4 kW from a 28- to 35-V bus and converts it into the seven outputs required for startup and operation of the thruster. The simplified power supply contains only about 500 parts and has demonstrated an unprecedented efficiency of 90 percent and a specific mass of about 8 kg/kW. The results of a highly successful wear-mechanism test in which the working-model XIPS was operated for 4350 hours and 3850 ON/OFF cycles are presented. These hours and cycles are equivalent to over ten years of NSSK on large communication satellites.

Beattie, J. R.↗

Performance Evaluation of the T6 Ion Engine

The T6 ion engine is a 22-cm diameter, 4.5-kW Kaufman-type ion thruster produced by QinetiQ, Ltd., and is baselined for the European Space Agency BepiColombo mission to Mercury and is being qualified under ESA sponsorship for the extended range AlphaBus communications satellite platform. The heritage of the T6 includes the T5 ion thruster now successfully operating on the ESA GOCE spacecraft. As a part of the T6 development program, an engineering model thruster was subjected to a suite of performance tests and plume diagnostics at the Jet Propulsion Laboratory. The engine was mounted on a thrust stand and operated over its nominal throttle range of 2.5 to 4.5 kW. In addition to the typical electrical and flow measurements, an E x B mass analyzer, scanning Faraday probe, thrust vector probe, and several near-field probes were utilized. Thrust, beam divergence, double ion content, and thrust vector movement were all measured at four separate throttle points. The engine performance agreed well with published data on this thruster. At full power the T6 produced 143 mN of thrust at a specific impulse of 4120 seconds and an efficiency of 64%; optimization of the neutralizer for lower flow rates increased the specific impulse to 4300 seconds and the efficiency to nearly 66%. Measured beam divergence was less than, and double ion content was greater than, the ring-cusp-design NSTAR thruster that has flown on NASA missions. The measured thrust vector offset depended slightly on throttle level and was found to increase with time as the thruster approached thermal equilibrium.

Snyder, John Steven↗

Enhancing Nasa Sounding Rocket Capabilities Through Composite Material Adoption

Sounding rockets are a suborbital research platform employed by NASA for heliophysics, astrophysics, and geospace science investigations, and for technology development. They follow semi-parabolic trajectories and are launched using surplus military, and commercial, solid-propellant rocket motors. NASA sounding rocket payloads are comprised of standard, modular subassemblies, designed to perform specific functions critical to achieving mission success criteria. Since the program’s inception, payload length and mass have trended upwards, limiting the capability of the platform to reach exospheric apogees and decreasing the time above critical altitudes to observe solar and celestial targets. To offset this trend, composite materials may be of use in payload and subsystem design to decrease payload mass. This investigation seeks to understand if there is a practical benefit to introducing composite materials on the NSRP by assessing mission specific impacts to those missions conducted in fiscal year 2024. To accurately estimate the mass of a composites-based payload, a standard subsystem (NIACS) underwent structural reconfiguration. Materials were selected that align with NSRP design, manufacturing, and testing standards. NIACS reconfiguration resulted in a mass reduction of 19.6% which was then applied to the payload system in entirety. Using vehicle performance carpet plots, delta apogee and time above the Kármán line were determined. Performance improvements were then evaluated against that mission’s success criteria to determine if that mission would have benefitted from using composite materials. On average, each mission would have gained 59.8 kilometers apogee and 62.9 seconds above the Kármán line. However, only nine of the seventeen missions would have benefitted from these performance improvements. Two of the missions could have used a lower-impulse launch vehicle to achieve mission success. Upleg stability met programmatic criteria; downleg instability and dynamic pressure improved, showing that ballast would not offset the mass reduction of using composite materials. Cost analysis showed that production costs will increase 39%. For the two missions that could have used a lower-impulse launch vehicle, the cost of the launch vehicle would have offset payload production costs. In summary, composite materials are not recommended for universal use on NASA sounding rocket payloads due to unclear programmatic benefits and added cost. However, they are justified for optical astrophysics and heliophysics missions, high-apogee (exosphere) requirements, or when they reduce payload costs versus higher impulse launch vehicles. Reflown, recoverable subsystems should use composites to enhance apogee and observation time.

Robert Henry Burth↗

Energetics and dynamics in a large solar flare of 1989 March

Solar Maximum Mission X-ray observations and National Solar Observatory/Sacramento Peak H alpha spectra are combined in a large (X1.2) solar flare to test predictions of chromospheric heating and evaporation by nonthermal thick-target electrons. It is demonstrated that the ratio of H alpha flare energy flux to the energy flux deposited by thick-target electrons obeys a power-law dependence on electron heating flux, with a slope that is consistent with that predicted by a thick-target electron transport and heating model in a 1D hydrostatic atmosphere. It is concluded that the thick-target model satisfactorily accounts for the observed magnitude of chromospheric H alpha emission, and the amplitudes and timing of oppositely directed plasma motions during the impulsive phase of this X flare.

Wulser, Jean-Pierre↗

Ultra High Voltage Propellant Isolators and Insulators for JIMO Ion Thrusters

Within NASA's Project Prometheus, high specific impulse ion thrusters for electric propulsion of spacecraft for the proposed Jupiter Icy Moon Orbiter (JIMO) mission to three of Jupiter's moons: Callisto, Ganymede and Europa will require high voltage operation to meet mission propulsion. The anticipated approx.6,500 volt net ion energy will require electrical insulation and propellant isolation which must exceed that used successfully by the NASA Solar Electric Propulsion Technology Readiness (NSTAR) Deep Space 1 mission thruster by a factor of approx.6. Xenon propellant isolator prototypes that operate at near one atmosphere and prototypes that operate at low pressures (<100 Torr) have been designed and are being tested for suitability to the JIMO mission requirements. Propellant isolators must be durable to Paschen breakdown, sputter contamination, high temperature, and high voltage while operating for factors longer duration than for the Deep Space 1 Mission. Insulators used to mount the thrusters as well as those needed to support the ion optics have also been designed and are under evaluation. Isolator and insulator concepts, design issues, design guidelines, fabrication considerations and performance issues are presented. The objective of the investigation was to identify candidate isolators and insulators that are sufficiently robust to perform durably and reliably during the proposed JIMO mission.

Banks, Bruce A.↗