Search NASA⌕ Search

SEARCH · Search NASA

Results for “rectifiers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Regenerative Snubber For GTO-Commutated SCR Inverter

Proposed regenerative snubbing circuit substituted for dissipative snubbing circuit in inverter based on silicon controlled rectifiers (SCR's) commutated by gate-turn-off thyristor (GTO). Intended to reduce loss of power that occurs in dissipative snubber. Principal criteria in design: low cost, simplicity, and reliability.

Rippel, Wally E.↗

Development of software to improve AC power quality on large spacecraft

To insure the reliability of a 20 kHz, AC power system on spacecraft, it is essential to analyze its behavior under many adverse operating conditions. Some of these conditions include overloads, short circuits, switching surges, and harmonic distortions. Harmonic distortions can cause malfunctions in equipment that the power system is supplying, and during extreme distortions such as voltage resonance, it can cause equipment and insulation failures due to the extreme peak voltages. HARMFLO, a power flow computer program, which was capable of analyzing harmonic conditions on three phase, balanced, 60 Hz, AC power systems, was modified to analyze single phase, 20 kHz, AC power systems. Since almost all of the equipment used on spacecraft power systems is electrically different from equipment used on terrestrial power systems, it was also necessary to develop mathematical models for the equipment to be used on the spacecraft. The results are that (1) the harmonic power now has a model of a single phase, voltage controlled, full wave rectifier; and (2) HARMFLO was ported to the SUN workstation platform.

Kraft, L. Alan↗

Final STS-35 Columbia descent BET products and results for LaRC OEX investigations

Final STS-35 'Columbia' descent Best Estimate Trajectory (BET) products have been developed for Langley Research Center (LaRC) Orbiter Experiments (OEX) investigations. Included are the reconstructed inertial trajectory profile; the Extended BET, which combines the inertial data and, in this instance, the National Weather Service atmospheric information obtained via Johnson Space Center; and the Aerodynamic BET. The inertial BET utilized Inertial Measurement Unit 1 (IMU1) dynamic measurements for deterministic propagation during the ENTREE estimation process. The final estimate was based on the considerable ground based C-band tracking coverage available as well as Tracking Data and Relay Satellite System (TDRSS) Doppler data, a unique use of the latter for endo-atmospheric flight determinations. The actual estimate required simultaneous solutions for the spacecraft position and velocity, spacecraft attitude, and six IMU parameters - three gyro biases and three accelerometer scale factor correction terms. The anchor epoch for this analysis was 19,200 Greenwich Mean Time (GMT) seconds which corresponds to an initial Shuttle altitude of approximately 513 kft. The atmospheric data incorporated were evaluated based on Shuttle derived considerations as well as comparisons with other models. The AEROBET was developed based on the Extended BET, the measured spacecraft configuration information, final mass properties, and the final Orbiter preoperation databook. The latter was updated based on aerodynamic consensus incrementals derived by the latest published FAD. The rectified predictions were compared versus the flight computed values and the resultant differences were correlated versus ensemble results for twenty-two previous STS entry flights.

Oakes, Kevin F.↗

The TOPSAR interferometric radar topographic mapping instrument

We have augmented the NASA DC-8 Airborne Synthetic Aperture Radar (AIRSAR) instrument with a pair of C-band antennas displaced across the track to form an interferometer sensitive to topographic variations of the Earth's surface. The antennas were developed by Alenia Spazio under the sponsorship of the Italian Space Agency (ASI), and the AIRSAR instrument and modifications to it supporting TOPSAR were sponsored by NASA. A new data processor was developed at JPL for producing the topographic maps. As of May 1991, one engineering flight line over San Francisco, CA was reduced to a cartographically rectified topographic map. Analysis of the results indicates that statistical errors are in the range of 2 to 4 m, while systematic effects due to aircraft motion are in the range of 6 to 12 m. Future aircraft motion compensation algorithms should reduce the systematic variations to near zero, while the statistical errors could likely be reduced to 2 m or less with some processor improvements.

Zebker, Howard A.↗

Magnetic Repeat Station Data

The nature, purpose, availability and distribution of magnetic repeat stations data are reviewed. Attention is paid to how repeat station data are obtained, sources of errors and limitations on accuracy. Repeat station results cannot achieve the accuracy of magnetic observatory estimates of the secular variation, but are, nevertheless, essential for improving the limited spatial coverage provided by observatories. The lack of appropriate standards and reporting procedures have meant that most global field molders have made little, or no, use of repeat data. Partly to rectify this problem, IAGA Working Group V-4 has instigated a scheme for systematic reporting and classification of magnetic repeat station data. The scheme will help to ensure that proper use is made of the wealth of repeat data that is available, and will also promote better observational practices.

Barton, C. E.↗

Rainfall estimation over oceans from SMMR and SSM/I microwave data

The brightness temperature (T sub b) measured at 37 GHz shows fairly strong emission from rain, and only slight effects caused by scattering by ice above the rain clouds. At frequencies below 37 GHz, where the FOV is larger and the volume extinction coefficient is weaker, it is found that the observations do not yield appreciable additional information about rain. At 85 GHz (FOV = 15 km), where the volume extinction is considerably larger, direct information about rain below the clouds is usually masked. Based on the above idea, 37 GHz observations with a 30 km FOV from SMMR and SSM/I are selected to develop an empirical method for the estimation of rain rate. In this method, the statistics of the observed T sub b's at 37 GHz in a rain storm are related to the rain rate statistics in that storm. The underestimation of rain rate, arising from the inability of the radiometer to respond sensitively to rain rate above a given threshold is rectified in this technique with the aid of two parameters that depend on the total water vapor content in the atmosphere. The retrieved rain rates compare favorably with radar observations and monthly mean global maps of rain derived from this technique over the oceans.

Prabhakara, C.↗

Lunar PMAD technology assessment

This report documents an initial set of power conditioning models created to generate 'ballpark' power management and distribution (PMAD) component mass and size estimates. It contains converter, rectifier, inverter, transformer, remote bus isolator (RBI), and remote power controller (RPC) models. These models allow certain studies to be performed; however, additional models are required to assess a full range of PMAD alternatives. The intent is to eventually form a library of PMAD models that will allow system designers to evaluate various power system architectures and distribution techniques quickly and consistently. The models in this report are designed primarily for space exploration initiative (SEI) missions requiring continuous power and supporting manned operations. The mass estimates were developed by identifying the stages in a component and obtaining mass breakdowns for these stages from near term electronic hardware elements. Technology advances were then incorporated to generate hardware masses consistent with the 2000 to 2010 time period. The mass of a complete component is computed by algorithms that calculate the masses of the component stages, control and monitoring, enclosure, and thermal management subsystem.

Metcalf, Kenneth J.↗

System for memorizing maximum values

The invention discloses a system capable of memorizing maximum sensed values. The system includes conditioning circuitry which receives the analog output signal from a sensor transducer. The conditioning circuitry rectifies and filters the analog signal and provides an input signal to a digital driver, which may be either linear or logarithmic. The driver converts the analog signal to discrete digital values, which in turn triggers an output signal on one of a plurality of driver output lines n. The particular output lines selected is dependent on the converted digital value. A microfuse memory device connects across the driver output lines, with n segments. Each segment is associated with one driver output line, and includes a microfuse that is blown when a signal appears on the associated driver output line.

Bozeman, Richard J., Jr.↗

Space Station Freedom combustion research

Extended operations in microgravity, on board spacecraft like Space Station Freedom, provide both unusual opportunities and unusual challenges for combustion science. On the one hand, eliminating the intrusion of buoyancy provides a valuable new perspective for fundamental studies of combustion phenomena. On the other hand, however, the absence of buoyancy creates new hazards of fires and explosions that must be understood to assure safe manned space activities. These considerations - and the relevance of combustion science to problems of pollutants, energy utilization, waste incineration, power and propulsion systems, and fire and explosion hazards, among others - provide strong motivation for microgravity combustion research. The intrusion of buoyancy is a greater impediment to fundamental combustion studies than to most other areas of science. Combustion intrinsically heats gases with the resulting buoyant motion at normal gravity either preventing or vastly complicating measurements. Perversely, this limitation is most evident for fundamental laboratory experiments; few practical combustion phenomena are significantly affected by buoyancy. Thus, we have never observed the most fundamental combustion phenomena - laminar premixed and diffusion flames, heterogeneous flames of particles and surfaces, low-speed turbulent flames, etc. - without substantial buoyant disturbances. This precludes rational merging of theory, where buoyancy is of little interest, and experiments, that always are contaminated by buoyancy, which is the traditional path for developing most areas of science. The current microgravity combustion program seeks to rectify this deficiency using both ground-based and space-based facilities, with experiments involving space-based facilities including: laminar premixed flames, soot processes in laminar jet diffusion flames, structure of laminar and turbulent jet diffusion flames, solid surface combustion, one-dimensional smoldering, ignition and flame spread of liquids, drop combustion, and quenching of panicle-air flames. Unfortunately, the same features that make microgravity attractive for fundamental combustion experiments, introduce new fire and explosion hazards that have no counterpart on earth. For example, microgravity can cause broader flammability limits, novel regimes of flame spread, enhanced effects of flame radiation, slower fire detector response, and enhanced combustion upon injecting fire extinguishing agents, among others. On the other hand, spacecraft provide an opportunity to use 'fire-safe' atmospheres due to their controlled environment. Investigation of these problems is just beginning, with specific fire safety experiments supplementing the space based fundamental experiments listed earlier; thus, much remains to be done to develop an adequate technology base for fire and explosion safety considerations for spacecraft.

Faeth, G. M.↗

Helicopter simulator standards

The initial advisory circular was produced in 1984 (AC 120-XX). It was not finalized, however, because the FAR's for pilot certification did not recognize helicopter simulators and, therefore, permitted no credit for their use. That is being rectified, and, when the new rules are published, standards must be available for qualifying simulators. Because of the lack of a data base to support specification of these standards, the FAA must rely on the knowledge of experts in the simulator/training industry. A major aim of this workshop is to form a working group of these experts to produce a set of standards for helicopter training simulators.

Boothe, Edward M.↗

Electromagnetic powered vehicles (EMPV) for Mars exploration

Microwave power beamed down from a Mars synchronous nuclear reactor power source to a rectifying antenna on a Mars rover is examined and compared to isotope, reactor, or photovoltaic systems as a power source to move a rover. Large ranges and higher power levels are possible with this microwave powered concept. The advantage of using higher frequencies, in the range of 500 to 1000 GHz, is examined and found to be substantial.

Christian, Jose L., Jr.↗

Normalization of cell responses in cat striate cortex

Simple cells in the striate cortex have been depicted as half-wave-rectified linear operators. Complex cells have been depicted as energy mechanisms, constructed from the squared sum of the outputs of quadrature pairs of linear operators. However, the linear/energy model falls short of a complete explanation of striate cell responses. In this paper, a modified version of the linear/energy model is presented in which striate cells mutually inhibit one another, effectively normalizing their responses with respect to stimulus contrast. This paper reviews experimental measurements of striate cell responses, and shows that the new model explains a significantly larger body of physiological data.

Heeger, D. J.↗

Half-squaring in responses of cat striate cells

Simple cells in striate cortex have been depicted as rectified linear operators, and complex cells have been depicted as energy mechanisms (constructed from the squared sums of linear operator outputs). This paper discusses two essential hypotheses of the linear/energy model: (1) that a cell's selectivity is due to an underlying (spatiotemporal and binocular) linear stage; and (2) that a cell's firing rate depends on the squared output of the underlying linear stage. This paper reviews physiological measurements of cat striate cell responses, and concludes that both of these hypotheses are supported by the data.

Heeger, D. J.↗

Topographic mapping using radar interferometry - Processing techniques

In the summer of 1991 the NASA DC-8 airborne synthetic aperture radar (SAR) system acquired data with the radar configured in a C-band across-track interferometer mode. The data were processed to generate rectified topographic maps. A new processing scheme was developed featuring motion compensation, absolute phase retrieval, and three-dimensional 1ocation. The new processor has been tested using data which were acquired with extreme aircraft motion so that performance could be evaluated under adverse conditions. The topographic maps generated by the radar were compared to Digital Elevation Models (DEM's) derived using conventional optical stereo techniques. In one region we measured rms elevation deviations which were less than the specified DEM accuracy, and in the region covered by the more accurate DEM we found errors varying from 2.2 m rms in relatively flat terrain up to 5.0 m in mountainous areas. The rms difference between radar and DEM elevations over the 6.5 km by 22 km area covered by the more accurate DEM was 3.6 m.

Madsen, Soren N.↗

Viewing analyses for the assembly of Space Station Freedom (SSF)

Analyses are currently being conducted in the Man-Systems Division of the NASA Johnson Space Center, on the restructured Space Station Freedom configuration to determine viewing requirements for both robotic tasks and for extravehicular crew activities. The use of the PLAID software, a 3D modeling simulation tool, provides a simulation of the environment and the system hardware to identify potential problem areas needing further refinement in design development. This process enables human factor considerations and issues to be explored during the design process to identify and correct problems before hardware is actually constructed. Preliminary results have identified several potential viewing problem areas with the available lighting for both robotic and EVA tasks. To rectify the potential viewing problems identified through simulation, additional cameras and lighting enhancements are being proposed at various sites along the truss and on the Shuttle to provide more complete coverage of work task sites. Supplementing the existing cameras with color coded alignment aids will also help reduce the workload involved with robotic tasks.

Stealey, Sheryl↗

Experimental verification of Theodorsen's theoretical jet-boundary correction factors

Prandtl's suggested use of a doubly infinite arrangement of airfoil images in the theoretical determination of wind-tunnel jet-boundary corrections was first adapted by Glauert to the case of closed rectangular jets. More recently, Theodorsen, using the same image arrangement but a different analytical treatment, has extended this work to include not only closed but also partly closed and open tunnels. This report presents the results of wind-tunnel tests conducted at the Georgia School of Technology for the purpose of verifying the five cases analyzed by Theodorsen. The tests were conducted in a square tunnel and the results constitute a satisfactory verification of his general method of analysis. During the preparation of the data two minor errors were discovered in the theory and these have been rectified.

Schliestett, George Van↗

Mathematical and experimental investigation of heat control and power increase in air-cooled aircraft engines

In order to understand the numerical relations between the air velocity, temperature of the cylinder walls, heat dissipation, cylinder dimensions and type of construction an experimental plant was installed in the Siemens and Halske laboratory. The experimental cylinder was exposed to the air stream of a wind tunnel. The compression chamber was heated by an electrically heated oil bath kept constantly in motion by a stirrer. The wall temperatures were measured by thermocouples. The air stream was produced a seven-watt blower. The air flowed through a current rectifier (honeycomb), diffuser, air chamber with quieting sieves and a nozzle.

ENGINES - AIR COOLED - POWER INCREASES↗

Alternating-Current Equipment for the Measurement of Fluctuations of Air Speed in Turbulent Flow

Recent electrical and mechanical improvements have been made in the equipment developed at the National Bureau of Standards for measurement of fluctuations of air speed in turbulent flow. Data useful in the design of similar equipment are presented. The design of rectified alternating-current power supplies for such apparatus is treated briefly, and the effect of the power supplies on the performance of the equipment is discussed.

Mock, W C , Jr↗