Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface planarization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Preliminary Measurements on the BOLT Geometry in the Supersonic Low Disturbance Tunnel

Experiments were performed in the Mach 3.5 Supersonic Low Disturbance Tunnel on the BOundary-Layer Transition (BOLT) geometry. The goal of this campaign was to assess changes to the transition front by varying the freestream noise and the model surface quality. The model was printed of polycarbonate and is 30% scale of the flight geometry. It was tested under noisy and quiet conditions at different streamwise positions in the tunnel and was also tested before and after improvements were made to the model surface through sanding and gap reduction. Pitch and yaw angles were nominally zero. The model surface temperature was measured using infrared thermography and thermocouples as the unit Reynolds number was swept from 4.75 -- 15.8 x 10^6 m^{-1}. Boundary-layer transition was observed near the midspan of the model for unit Reynolds numbers above 10 x 10^6 m^{-1} in quiet flow, while transition was already observed on the shoulders below 5 x 10^6 m^{-1} in noisy flow. The model surface enhancements improved the symmetry of the transition front for quiet flow but made only slight differences for noisy flow. In quiet flow, the impact of streamwise positioning on transition was more significant on the model shoulders compared to the central region. The difference in the shoulder heating was likely due to variation in noise radiated from the nozzle sidewalls. The total temperature and initial wall temperatures were near 300 K and 293 K, respectively, which generally resulted in negative convective heat-flux values into the model. Hot-wire anemometry was also utilized to characterize the freestream and to conduct a planar survey near the base of the model for the 7.92 x 10^6 m^{-1} quiet condition. The survey captured the thickening of the boundary layer at the centerline and the vortical nature of the flow outboard of it. Spectral analysis of the mass-flux fluctuations near the midspan demonstrates that the boundary layer is laminar and suggests that the thick boundary layer caused the relatively warm centerline observed in the infrared images.

boundary layer transition↗
DOE OSTI2024

Mitigating coherent loss in superconducting circuits using molecular self-assembled monolayers

In planar superconducting circuits, decoherence due to materials imperfections, especially two-level-system (TLS) defects at different interfaces, is a primary hurdle for advancing quantum computing and sensing applications. Traditional methods for mitigating TLS loss, such as etching oxide layers at metal and substrate interfaces, have proven to be inadequate due to the persistent challenge of oxide regrowth. In this work, we introduce a novel approach that employs molecular self-assembled monolayers (SAMs) to chemically bind at different interfaces of superconducting circuits. This technique is specifically tested here on coplanar waveguide (CPW) resonators, in which this method not only impedes oxide regrowth after surface etching but can also tailors the dielectric properties at different resonators interfaces. The deployment of SAMs results in a consistent improvement in the measured quality factors across multiple resonators, surpassing those with only oxide-etched resonators. The efficiency of our approach is supported by microwave measurements of multiple devices conducted at millikelvin temperatures and correlated with detailed X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) characterizations of SAM-passivated resonators. The compatibility of SAMs materials with the established fabrication techniques offers a promising route to improve the performance of superconducting quantum devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Medium voltage planar DC bus distributed capacitor array

An inverter with a modular bus assembly is described. In various embodiments, the modular bus assembly includes a laminated motherboard and a plurality of capacitor daughtercards. The laminated motherboard can be configured to interface a plurality of phase-leg modules and a plurality of capacitor daughtercards through a plurality of terminals and connectors located on a bottom side or a top side of the laminated motherboard. The laminated motherboard includes a layer stack with a plurality of conductor layers. Each of the plurality of conductor layers is implemented with a net spacing from a neighboring plated through hole (PTH) based at least in part on differences in potential to be applied to each of the plurality of conductor layers as compared to a potential to be applied to the PTH. Embedded shield polygons can be implemented on the laminated motherboard to mitigate surface discharge at surface terminal (PTH/SMT) triple junctions.

Ravi, Lakshmi↗
NASA NTRS2023

Magnetic Anisotropy and Stress Dependent Epoxy Wetting in FeNi-based Metal Amorphous Nanocomposite

Recently developed FeNi-based metal amorphous nanocomposites (MANCs) used in high-speed motors (HSMs) exhibit reduced eddy current losses while maintaining good mechanical properties and glass-forming abilities. Magnetic anisotropy in (Fe 70 Ni 30 ) 80 Nb 4 B 14 Si 2 amorphous magnetic ribbon (AMR) in the as-cast state and upon conventional (T CA ) and strain (T SA ) annealing heat treatment is investigated. From ribbon samples in as-cast condition, quenched in stress from planar flow casting (PFC) induced as-cast curvature derived uniaxial magnetic anisotropy. Stress relief by conventional furnace annealing at T CA > 350 °C achieved isotropic properties in the bulk. Annealing about the primary crystallization temperature, T CA ~ 450 °C, resulted in the formation of both FCC and BCC nanocrystallites and evolution to isotropic bulk magnetic properties confirming the random anisotropy model. In samples strain annealed at T SA = 440 °C at various tensions, relatively large controlled induced uniaxial anisotropy is achieved. The largest magnetic anisotropy occurs in annealing under the stress of 250 MPa yielding an anisotropy field of 7.1 x 10 4 A/m. Surface anisotropy observed by MOKE differs from bulk anisotropy due to image contrast from closure domains. Epoxy coatings are important for improved bonding, mechanical properties, and resistivity in tape-wound MANC cores for HSMs. Using a sessile droplet method, the equilibrium contact angle of an epoxy droplet on a tensile stress annealed MANC exhibits stress dependent surface energies. Anisotropic wetting in FeNi-based MANC heat treated at T CA = 440 °C mimics surface magnetic anisotropy observed by MOKE.

soft magnetic materials↗
DOE OSTI2019

Optical Effects of Divalent Functionalization of Carbon Nanotubes

Covalent functionalization of single-walled carbon nanotubes (SWCNTs) enables tuning of their optical properties through the generation of sp3-hybridized defects with distinct localized morphology. Groups with strong electron-withdrawing abilities result in redshifted emission experimentally. Further redshifts can be generated by groups bound to more than one carbon atom in the SWCNT (“divalent functionalization”). Depending on the type of divalent functionalization, the spectral diversity is reduced compared to their monovalent counterparts. Here we study the effect of divalent functionalization on the exciton localization at the defect site and related redshifts in emission of (6,5) SWCNT through low-temperature spectroscopy measurements and time dependent density functional theory calculations. These effects are characterized for three classes of divalent compounds distinct in the number of atoms in the functional group and bonding pattern to the tube. The bond character of the two carbon atoms proximal to the defect site is found to have a notable impact on the system stability and spectral redshifts. Functionalized systems are stabilized when the hybridization at the SWCNT remains sp2-like due to its ability to form planar bonds to the remaining hexagonal network, while bond character in the functionalized regions affects the redshifts. This is only possible for certain bonding geometries in divalent species, justifying their decreased spectral diversity. We further show that functionalization at spatially separated sites on the tube can be accompanied by a second chemical adduct, and the configuration of the resulting defect is dictated by bond reactivity following the first addition. This behavior justifies the spectral trends of a class of divalent systems with linker chains or high defect concentration. These results further corroborate that adducts predominantly form chemical bonds only to the neighboring carbons on the SWCNT surface (ortho species) in experimental samples. Our analysis of bond character in the vicinity of the defect sites rationalizes appearance of many spectral features arising from monovalent and divalent defect states of functionalized SWCNTs. As a result, this emerging understanding enables tuning of the emission characteristics through careful control of the defect structure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Large-area epitaxial growth of InAs nanowires and thin films on hexagonal boron nitride by metal organic chemical vapor deposition

Large-area epitaxial growth of III–V nanowires and thin films on van der Waals substrates is key to developing flexible optoelectronic devices. In our study, large-area InAs nanowires and planar structures are grown on hexagonal boron nitride templates using metal organic chemical vapor deposition method without any catalyst or pre-treatments. The effect of basic growth parameters on nanowire yield and thin film morphology is investigated. Under optimised growth conditions, a high nanowire density of 2.1 x 10 9 cm -2 is achieved. A novel growth strategy to achieve uniform InAs thin film on h-BN/SiO 2 /Si substrate is introduced. The approach involves controlling the growth process to suppress the nucleation and growth of InAs nanowires, while promoting the radial growth of nano-islands formed on the h-BN surface. A uniform polycrystalline InAs thin film is thus obtained over a large area with a dominant zinc-blende phase. The film exhibits near-band-edge emission at room temperature and a relatively high Hall mobility of 399 cm -2 /(Vs). This work suggests a promising path for the direct growth of large-area, low-temperature III–V thin films on van der Waals substrates.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Breaking Radial Dipole Symmetry in Planar Macrocycles Modulates Edge‐to‐Edge Packing and Disrupts Cofacial Stacking

Dipolar interactions are ever-present in supramolecular architectures, though their impact is typically revealed by making dipoles stronger. While it is also possible to assess the role of dipoles by altering their orientations by using synthetic design, doing so without altering the molecular shape is not straightforward. We have now done this by flipping one triazole unit in a rigid macrocycle, tricarb. The macrocycle is composed of three carbazoles (2 Debye) and three triazoles (5 Debye) defining an array of dipoles aligned radially but organized alternately in and out. These dipoles are believed to dictate edge-to-edge tiling and face-to-face stacking. We modified our synthesis to prepare isosteric macrocycles with the orientation of one triazole dipole rotated 40°. The new dipole orientation guides edge-to-edge contacts to reorder the stability of two surface-bound 2D polymorphs. The impact on dipole-enhanced π stacking, however, was unexpected. Our stacking model identified an unchanged set of short-range (3.4 Å) anti-parallel dipole contacts. Despite this situation, the reduction in self-association was attributed to long-range (~6.4 Å) dipolar repulsions between π-stacked macrocycles. This work highlights our ability to control the build-up and symmetry of macrocyclic skeletons by synthetic design, and the work needed to further our understanding of how dipoles control self-assembly.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Nanoporous Pt(Au) Alloys for the Enhanced, Non–enzymatic Detection of Hydrogen Peroxide under Biofouling Conditions

The non-enzymatic electrochemical sensing of hydrogen peroxide (H 2 O 2 ) is described. This study utilized a 3D bicontinuous nanoporous platinum-gold alloy-based sensor (NP-Pt(Au) electrode), which has a morphology that resembles a molecular sieve. SEM and CV were used to evaluate the morphological and electrochemical characteristics of the NP-Pt(Au) electrodes. The cathodic voltammetric response of H 2 O 2 was enhanced at the NP-Pt(Au) as compared to planar Pt electrodes. Further, the nanoporous electrode was able to maintain the H 2 O 2 voltammetric profile even in the presence of the biofouling agent, serum albumin. Its application as a non-enzymatic sensor for the amperometric measurement of H 2 O 2 was explored.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Spontaneous and field-induced crystallographic reorientation of metal electrodeposits at battery anodes

The propensity of metal anodes of contemporary interest (e.g., Li, Al, Na, and Zn) to form non-planar, dendritic morphologies during battery charging is a fundamental barrier to achievement of full reversibility. We experimentally investigate the origins of dendritic electrodeposition of Zn, Cu, and Li in a three-electrode electrochemical cell bounded at one end by a rotating disc electrode. We find that the classical picture of ion depletion–induced growth of dendrites is valid in dilute electrolytes but is essentially irrelevant in the concentrated (≥1 M) electrolytes typically used in rechargeable batteries. Using Zn as an example, we find that ion depletion at the mass transport limit may be overcome by spontaneous reorientation of Zn crystallites from orientations parallel to the electrode surface to dominantly homeotropic orientations, which appear to facilitate contact with cations outside the depletion layer. This chemotaxis-like process causes obvious texturing and increases the porosity of metal electrodeposits.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2017

The Lightweight Integrated Solar Array and anTenna (LISA-T) - Big Power for Small Spacecraft

NASA is developing a space power system using lightweight, flexible photovoltaic devices originally developed for use here on Earth to provide low cost power for spacecraft. The Lightweight Integrated Solar Array and anTenna (LISA-T) is a launch-stowed, orbit-deployed array on which thin-film photovoltaic and antenna elements are embedded. The LISA-T system is deployable, building upon NASA's expertise in developing thin-film deployable solar sails such the one being developed for the Near Earth Asteroid Scout project which will fly in 2018. One of the biggest challenges for the NEA Scout, and most other spacecraft, is power. There simply isn't enough of it available, thus limiting the range of operation of the spacecraft from the Sun (due to the small surface area available for using solar cells), the range of operation from the Earth (low available power with inherently small antenna sizes tightly constrain the bandwidth for communication), and the science (you can only power so many instruments with limited power). The LISA-T has the potential to mitigate each of these limitations. Inherently, small satellites are limited in surface area, volume, and mass allocation; driving competition between their need for power and robust communications with the requirements of the science or engineering payload they are developed to fly. LISA-T is addressing this issue, deploying large-area arrays from a reduced volume and mass envelope - greatly enhancing power generation and communications capabilities of small spacecraft and CubeSats. The problem is that these CubeSats can usually only generate between 7 watts and 50 watts of power. The power that can be generated by the LISA-T ranges from tens of watts to several hundred watts. A matrix of options are in development, including planar (pointed) and omnidirectional (non-pointed) arrays. The former is seeking the highest performance possible while the latter is seeking GN&C (Guidance, Navigation and Control) simplicity. In both cases, power generation ranges from tens of watts to several hundred with an expected specific power greater than 250 watts per kilogram and a stowed power density greater than 200 kilowatts per cubic meter. Options for leveraging both high performance, 'typical cost' triple junction thin-film solar cells as well as moderate performance, low cost cells are being developed. Alongside, both UHF (ultra high frequency) and S-band antennas are being integrated into the array to move their space claim away from the spacecraft and open the door for omnidirectional communications and electronically steered phase arrays.

Johnson, Les↗
DOE OSTI2020

Hydrometeor Shape Variability in Snowfall as Retrieved from Polarimetric Radar Measurements

A polarimetric radar–based method for retrieving atmospheric ice particle shapes is applied to snowfall measurements by a scanning Ka-band radar deployed at Oliktok Point, Alaska (70.495°N, 149.883°W). The mean aspect ratio, which is defined by the hydrometeor minor-to-major dimension ratio for a spheroidal particle model, is retrieved as a particle shape parameter. The radar variables used for aspect ratio profile retrievals include reflectivity, differential reflectivity, and the copolar correlation coefficient. The retrievals indicate that hydrometeors with mean aspect ratios below 0.2–0.3 are usually present in regions with air temperatures warmer than approximately from –17° to –15°C, corresponding to a regime that has been shown to be favorable for growth of pristine ice crystals of planar habits. Radar reflectivities corresponding to the lowest mean aspect ratios are generally between –10 and 10 dBZ. For colder temperatures, mean aspect ratios are typically in a range between 0.3 and 0.8. There is a tendency for hydrometeor aspect ratios to increase as particles transition from altitudes in the temperature range from –17° to –15°C toward the ground. Furthermore, this increase is believed to result from aggregation and riming processes that cause particles to become more spherical and is associated with areas demonstrating differential reflectivity decreases with increasing reflectivity. Aspect ratio retrievals at the lowest altitudes are consistent with in situ measurements obtained using a surface-based multiangle snowflake camera. Pronounced gradients in particle aspect ratio profiles are observed at altitudes at which there is a change in the dominant hydrometeor species, as inferred by spectral measurements from a vertically pointing Doppler radar.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1987

Exact-image method for Gaussian-beam problems involving a planar interface

The exact-image method, recently introduced for the solution of electromagnetic field problems involving sources above a planar interface between two homogeneous media, is shown to be valid also for sources located in complex space, which makes its application possible for Gaussian-beam analysis. It is demonstrated that the Goos-Hanchen shift and the angular shift of a TE-polarized beam are correctly given as asymptotic results by the exact-reflection-image theory. Also, the apparent-image location giving the correct Gaussian beam transmitted through the interface is obtained as another asymptotic check. The theory described here makes it possible to calculate the exact coupling from the Gaussian beam to the reflected and refracted beams as well as to the surface wave.

Lindell, Ismo V.↗
NASA NTRS2011

NASA Tech Briefs, July 2011

Topics covered include: 1) Collaborative Clustering for Sensor Networks; 2) Teleoperated Marsupial Mobile Sensor Platform Pair for Telepresence Insertion Into Challenging Structures; 3) Automated Verification of Spatial Resolution in Remotely Sensed Imagery; 4) Electrical Connector Mechanical Seating Sensor; 5) In Situ Aerosol Detector; 6) Multi-Parameter Aerosol Scattering Sensor; 7) MOSFET Switching Circuit Protects Shape Memory Alloy Actuators; 8) Optimized FPGA Implementation of Multi-Rate FIR Filters Through Thread Decomposition; 9) Circuit for Communication Over Power Lines; 10) High-Efficiency Ka-Band Waveguide Two-Way Asymmetric Power Combiner; 11) 10-100 Gbps Offload NIC for WAN, NLR, and Grid Computing; 12) Pulsed Laser System to Simulate Effects of Cosmic Rays in Semiconductor Devices; 13) Flight Planning in the Cloud; 14) MPS Editor; 15) Object-Oriented Multi Disciplinary Design, Analysis, and Optimization Tool; 16) Cryogenic-Compatible Winchester Connector Mount and Retaining System for Composite Tubes; 17) Development of Position-Sensitive Magnetic Calorimeters for X-Ray Astronomy; 18) Planar Rotary Piezoelectric Motor Using Ultrasonic Horns; 19) Self-Rupturing Hermetic Valve; 20) Explosive Bolt Dual-Initiated from One Side; 21) Dampers for Stationary Labyrinth Seals; 22) Two-Arm Flexible Thermal Strap; 23) Carbon Dioxide Removal via Passive Thermal Approaches; 24) Polymer Electrolyte-Based Ambient Temperature Oxygen Microsensors for Environmental Monitoring; 25) Pressure Shell Approach to Integrated Environmental Protection; 26) Image Quality Indicator for Infrared Inspections; 27) Micro-Slit Collimators for X-Ray/Gamma-Ray Imaging; 28) Scatterometer-Calibrated Stability Verification Method; 29) Test Port for Fiber-Optic-Coupled Laser Altimeter; 30) Phase Retrieval System for Assessing Diamond Turning and Optical Surface Defects; 31) Laser Oscillator Incorporating a Wedged Polarization Rotator and a Porro Prism as Cavity Mirror; 32) Generic, Extensible, Configurable Push-Pull Framework for Large-Scale Science Missions; 33) Dynamic Loads Generation for Multi-Point Vibration Excitation Problems; 34) Optimal Control via Self-Generated Stochasticity; 35) Space-Time Localization of Plasma Turbulence Using Multiple Spacecraft Radio Links; 36) Surface Contact Model for Comets and Asteroids; 37) Dust Mitigation Vehicle; 38) Optical Coating Performance for Heat Reflectors of the JWST-ISIM Electronic Component; 39) SpaceCube Demonstration Platform; 40) Aperture Mask for Unambiguous Parity Determination in Long Wavelength Imagers; 41) Spaceflight Ka-Band High-Rate Radiation-Hard Modulator; 42) Enabling Disabled Persons to Gain Access to Digital Media; 43) Cytometer on a Chip; 44) Principles, Techniques, and Applications of Tissue Microfluidics; and 45) Two-Stage Winch for Kites and Tethered Balloons or Blimps.

Source record↗
DOE OSTI2020

Production of C 2 /C 3 Oxygenates from Planar Copper Nitride-Derived Mesoporous Copper via Electrochemical Reduction of CO 2

Electrochemical reduction of CO 2 provides an opportunity to produce fuels and chemicals in a carbon-neutral manner, assuming that CO 2 can be captured from the atmosphere. To do so requires efficient, selective, and stable catalysts. In this study, we report a highly mesoporous metallic Cu catalyst prepared by electrochemical reduction of thermally nitrided Cu foil. Under aqueous saturated CO 2 reduction conditions, the Cu 3 N-derived Cu electrocatalyst produces virtually no CH 4 , very little CO, and exhibits a faradaic efficiency of 68% in C 2+ products (C 2 H 4 , C 2 H 5 OH, and C 3 H 7 OH) at a current density of ~18.5 mA cm –2 and a cathode potential of -1.0 V versus the reversible hydrogen electrode. Under these conditions, the catalyst produces more oxygenated products than hydrocarbons. We show that surface roughness is a good descriptor of catalytic performance. The roughest surface reached 98% CO utilization efficiency for C 2+ product formation from CO 2 reduction and the ratio of oxygenated to hydrocarbon products correlates with the degree of surface roughness. These effects of surface roughness are attributed to the high population of undercoordinated sites as well as a high pH environment within the mesopores and adjacent to the surface of the catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1979

Magnetohydrodynamic models of coronal transients in the meridional plane. II - Simulation of the coronal transient of 1973 August 21

A two-dimensional planar MHD model of solar atmospheric transient events is used to simulate the flare-associated events of August 21, 1973. This event, observed in H-alpha, He II 304 A, soft X-ray, and coronal white light, provided sufficient information (especially in the latter diagnostic) for an assessment to be made of the model's ability to simulate major features of an actual solar event. It was found that a thermodynamic input pulse based on data provided by the NASA Marshall Space Flight Center-Aerospace Corporation X-ray telescope (S-056) on Skylab was sufficient to produce the global geometry, shock and contact-surface velocities, excess mass contours, and energy budget which were, for the most part, observed by the High Altitude Observatory white-light coronagraph (S-052) on Skylab in the form of a forerunner and coronal transient.

Dryer, M.↗
NASA NTRS2000

Impact Crater in Coastal Patagonia

Impact craters are geological structures attributed to the impact of a meteoroid on the Earth's (or other planet's) surface (Koeberl and Sharpton. 1999). The inner planets of the solar system as well as other bodies such as our moon show extensive meteoroid impacts (Gallant 1964, French 1998). Because of its size and gravity, we may assume that the Earth has been heavily bombarded but weathering and erosion have erased or masked most of these features. In the 1920's, a meteor crater (Mark 1987) was identified in Arizona and to this first finding the identification of a large number of impact structures on Earth followed (Hodge 1994). Shock metamorphic effects are associated with meteorite impact craters. Due to extremely high pressures, shatter cones are produced as well as planar features in quartz and feldspar grains, diaplectic glass and high-pressure mineral phases such as stishovite (French 1998).

D'Antoni, Hector L↗
DOE OSTI2024

Flower-shaped 2D crystals grown in curved fluid vesicle membranes

Abstract The morphologies of two-dimensional (2D) crystals, nucleated, grown, and integrated within 2D elastic fluids, for instance in giant vesicle membranes, are dictated by an interplay of mechanics, permeability, and thermal contraction. Mitigation of solid strain drives the formation of crystals with vanishing Gaussian curvature (i.e., developable domain shapes) and, correspondingly, enhanced Gaussian curvature in the surrounding 2D fluid. However, upon cooling to grow the crystals, large vesicles sustain greater inflation and tension because their small area-to-volume ratio slows water permeation. As a result, more elaborate shapes, for instance, flowers with bendable but inextensible petals, form on large vesicles despite their more gradual curvature, while small vesicles harbor compact planar crystals. This size dependence runs counter to the known cumulative growth of strain energy of 2D colloidal crystals on rigid spherical templates. This interplay of intra-membrane mechanics and processing points to the scalable production of flexible molecular crystals of controllable complex shape.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exploring the Tl 2H 2 potential energy surface: A comparative analysis with group 13 systems and experiment

Abstract Thallium chemistry is experiencing unprecedented importance. Therefore, it is valuable to characterize some of the simplest thallium compounds. Stationary points along the singlet and triplet TlH potential energy surface have been characterized. Stationary point geometries were optimized with the CCSD(T)/aug‐cc‐pwCVQZ‐PP method. Harmonic vibrational frequencies were computed at the same level of theory while anharmonic vibrational frequencies were computed at the CCSD(T)/aug‐cc‐pwCVTZ‐PP level of theory. Final energetics were obtained with the CCSDT(Q) method. Basis sets up to augmented quintuple‐zeta cardinality (aug‐cc‐pwCV5Z‐PP) were employed to obtain energetics in order to extrapolate to the complete basis set limits using the focal point approach. Zero‐point vibrational energy corrections were appended to the extrapolated energies in order to determine relative energies at 0 K. It was found that the planar dibridged isomer lies lowest in energy while the linear structure lies highest in energy. The results were compared to other group 13 MH (M = B, Al, Ga, In, and Tl) theoretical studies and some interesting variations are found. With respect to experiment, incompatibilities exist.

Chemistry↗