Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface steps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Two-Color Ultrafast Photoexcited Scanning Tunneling Microscopy

We report on two-color two-photon photoexcitation of a metal surface driven by ultrafast laser pulses and detected with a scanning tunneling microscope (STM) tip as a proximate anode. Results are presented for two cases: (i) where the tip is retracted from the surface far enough to prohibit tunneling, and (ii) where the tip is within tunneling range of the surface. A delay-modulation technique is implemented to isolate the two-color photoemission from concurrent one-color two-photon photoemission and provide subpicosecond time-resolved detection. When applied with the tip in tunneling range, this approach effectively isolates the two-photon photoexcited current signal from the conventional tunneling current and enables subpicosecond time-resolved detection of the photoexcited surface electrons. The advantage of the two-color approach is highlighted by comparison with the one-color case where optical interference causes thermal modulation of the STM tip length, resulting in tunneling current modulations that are orders of magnitude larger than the current due to photoexcitation of surface electrons. By completely eliminating this interference, and thereby avoiding thermal modulation of the STM tip length, the two-color approach represents an important step toward the ultimate goal of simultaneous subnanometer and subpicosecond measurements of surface electron dynamics by ultrafast-laser-excited STM.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rapid Guest Exchange and Ultra‐Low Surface Tension Solvents Optimize Metal–Organic Framework Activation

Abstract Exploratory research into the critical steps in metal–organic framework (MOF) activation involving solvent exchange and solvent evacuation are reported. It is discovered that solvent exchange kinetics are extremely fast, and minutes rather days are appropriate for solvent exchange in many MOFs. It is also demonstrated that choice of a very low surface tension solvent is critical in successfully activating challenging MOFs. MOFs that have failed to be activated previously can achieve predicted surface areas provided that lower surface tension solvents, such as n‐hexane and perfluoropentane, are applied. The insights herein aid in the efficient activation of MOFs in both laboratory and industrial settings and provide best practices for avoiding structural collapse.

Ma, Jialiu↗

Investigation of thin oxide layer removal from Si substrates using an SiO 2 atomic layer etching approach: the importance of the reactivity of the substrate

The evaluation of a plasma-based atomic layer etching (ALE) approach for native oxide surface removal from Si substrates is described. Objectives include removal of the native oxide while minimizing substrate damage, surface residues and substrate loss. Oxide thicknesses were measured using in situ ellipsometry and surface chemistry was analyzed by x-ray photoelectron spectroscopy. The cyclic ALE approach when used for removal of native oxide SiO 2 from a Si substrate did not remove native oxide to the extent required. This is due to the high reactivity of the silicon substrate during the low-energy (<40 eV) ion bombardment phase of the cyclic ALE approach which leads to reoxidation of the silicon surface. A modified process, which used continuously biased Ar plasma with periodic CF 4 injection, achieved significant oxygen removal from the Si surface, with some residual carbon and fluorine. A subsequent H 2 /Ar plasma exposure successfully removed residual carbon and fluorine while passivating the silicon surface. The combined treatment reduced oxygen and carbon levels to about half compared to as received silicon surfaces. The downside of this process sequence is a net loss of about 40 Å of Si. A generic insight of this work is the importance of the substrate and final surface chemistry in addition to precise etch control of the target film for ALE processes. By a fluorocarbon-based ALE technique, thin SiO 2 layer removal at the Ångstrom level can be precisely performed from an inert substrate, e.g. a thick SiO 2 layer. However, from a reactive substrate, like Si, complete removal of the thin SiO 2 layer is prevented by the high reactivity of low energy Ar + ion bombarded Si. In conclusion, the Si surfaces are reoxidized during the ALE ion bombardment etch step, even for very clean and ultra-low O 2 process conditions.

XPS↗

Clustering on Magnesium Surfaces – Formation and Diffusion Energies

The formation and diffusion energies of atomic clusters on Mg surfaces determine the surface roughness and formation of faulted structure, which in turn affect the mechanical deformation of Mg. This paper reports first principles density function theory (DFT) based quantum mechanics calculation results of atomic clustering on the low energy surfaces {0001} and {$\bar{1}$011} . In parallel, molecular statics calculations serve to test the validity of two interatomic potentials and to extend the scope of the DFT studies. On a {0001} surface, a compact cluster consisting of few than three atoms energetically prefers a face-centered-cubic stacking, to serve as a nucleus of stacking fault. On a {$\bar{1}$011} , clusters of any size always prefer hexagonal-close-packed stacking. Adatom diffusion on surface {$\bar{1}$011} is high anisotropic while isotropic on surface (0001). Three-dimensional Ehrlich–Schwoebel barriers converge as the step height is three atomic layers or thicker. FInally, adatom diffusion along steps is via hopping mechanism, and that down steps is via exchange mechanism.

36 MATERIALS SCIENCE↗

High efficiency screen-printed n-type silicon solar cell using co-diffusion of APCVD boron emitter and POCl 3 back surface field

We present the fabrication and analysis of Passivated Emitter and Rear Totally Diffused (PERT) solar cells on n-type silicon using a co-diffusion process. In a single high temperature step, a BSG/SiO x stack deposited by APCVD and a POCl 3 back surface field diffuse into the wafer to form the boron doped emitter and phosphorus doped back surface field. The SiO x layer on top of BSG acts as a masking layer to prevent cross-doping of phosphorus as well as a blocking layer for boron out-diffusion. This resulted in an initial sheet resistance of 76 Ω with good uniformity and a final p + emitter sheet resistance of 97 Ω after boron rich layer removal. Additionally, bulk lifetime was investigated before and after the high temperature step that resulted in an increase from 1.2 ms to 1.5 ms due to a POCl 3 gettering effect. Finally, a peak cell efficiency of 20.3% was achieved and each recombination component in terms of saturation current density was calculated and analyzed to understand the cell for further efficiency enhancement.

14 SOLAR ENERGY↗

Quantum chemical elucidation of the mechanism for hydrogenation of TiO{sub 2} anatase crystals

Hydrogenation of TiO{sub 2} is relevant to hydrogen storage and water splitting. We have carried out a detailed mechanistic study on TiO{sub 2} hydrogenation through H and/or H{sub 2} diffusion from the surface into subsurface layers of anatase TiO{sub 2} (101) by periodic density functional theory calculations implementing on-site Coulomb interactions (DFT + U). Both H atoms and H{sub 2} molecules can migrate from the crystal surface into TiO{sub 2} near subsurface layer with 27.8 and 46.2 kcal/mol energy barriers, respectively. The controlling step for the former process is the dissociative adsorption of H{sub 2} on the surface which requires 47.8 kcal/mol of energy barrier. Both hydrogen incorporation processes are expected to be equally favorable. The barrier energy for H{sub 2} migration from the first layer of the subsurface O{sub sub1} to the 2nd layer of the subsurface oxygen O{sub sub2} requires only 6.6 kcal. The presence of H atoms on the surface and inside the subsurface layer tends to promote both H and H{sub 2} penetration into the subsurface layer by reducing their energy barriers, as well as to prevent the escape of the H{sub 2} from the cage by increasing its escaping barrier energy. The H{sub 2} molecule inside a cage can readily dissociate and form 2HO-species exothermically ({Delta}H =-31.0 kcal/mol) with only 26.2 kcal/mol barrier. The 2HO-species within the cage may further transform into H{sub 2}O with a 22.0 kcal/mol barrier and 19.3 kcal/mol exothermicity relative to the caged H{sub 2} molecule. H{sub 2}O formation following the breaking of Ti-O bonds within the cage may result in the formation of O-vacancies and surface disordering as observed experimentally under a high pressure and moderately high temperature condition. According to density of states analysis, the projected density of states of the interstitial H, H{sub 2}, and H{sub 2}O appear prominently within the TiO{sub 2} band gap; in addition, the former induces a shift of the band gap position notably towards the conduction band. The thermochemistry for formation of the most stable sub-surface species (2HO and H{sub 2}O) has been predicted. These results satisfactorily account for the photo-catalytic activity enhancement observed experimentally by hydrogenation at high temperatures and high pressures.

36 MATERIALS SCIENCE↗

Dissoluton of Biogenic And Synthetic UO(2) Under Varied Reducing Conditions

The chemical stability of biogenic UO{sub 2}, a nanoparticulate product of environmental bioremediation, may be impacted by the particles' surface free energy, structural defects, and compositional variability in analogy to abiotic UO{sub 2+x} (0 {<=} x {<=} 0.25). This study quantifies and compares intrinsic solubility and dissolution rate constants of biogenic nano-UO{sub 2} and synthetic bulk UO{sub 2.00}, taking molecular-scale structure into account. Rates were determined under anoxic conditions as a function of pH and dissolved inorganic carbon in continuous-flow experiments. The dissolution rates of biogenic and synthetic UO{sub 2} solids were lowest at near neutral pH and increased with decreasing pH. Similar surface area-normalized rates of biogenic and synthetic UO{sub 2} suggest comparable reactive surface site densities. This finding is consistent with the identified structural homology of biogenic UO{sub 2} and stoichiometric UO{sub 2.00}. Compared to carbonate-free anoxic conditions, dissolved inorganic carbon accelerated the dissolution rate of biogenic UO{sub 2} by 3 orders of magnitude. This phenomenon suggests continuous surface oxidation of U(IV) to U(VI), with detachment of U(VI) as the rate-determining step in dissolution. Although reducing conditions were maintained throughout the experiments, the UO{sub 2} surface can be oxidized by water and radiogenic oxidants. Even in anoxic aquifers, UO{sub 2} dissolution may be controlled by surface U(VI) rather than U(IV) phases.

54 ENVIRONMENTAL SCIENCES↗

Facile fabrication of three-dimensional mesoporous Si/SiC composites via one-step magnesiothermic reduction at relative low temperature

Graphical abstract: - Highlights: • The Si/SiC composites were synthesized by one-step magnesiothermic reduction. • The mesoporous composites have a high specific surface area (655.7 m{sup 2} g{sup −1}). • The composites exhibited a strong photoluminescence and better biocompatibility. • The mechanisms of formation and photoluminescence of sample were discussed. - Abstract: By converting modified silica aerogels to the corresponding silicon/silicon carbide (Si/SiC) without losing its nanostructure, three-dimensional mesoporous (3DM) Si/SiC composites are successfully synthesized via one-step magnesothermic reduction at relative low temperature (650 °C). The phase composition and microstructure of the resulting samples are measured by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), Raman spectra, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). N{sub 2}-sorption isotherms results show that the products have high Brunauer–Emmett–Teller (BET) specific surface areas (up to 656 m{sup 2} g{sup −1}) and narrow pore-size distributions (1.5–30 nm). The composites exhibit a strong photoluminescence (PL) in blue-green light region (peak centered at 533 nm). We have set out work on the biocompatibility and enhancing PL of samples. As a result of excellent performances of the composites, it can be expected to have significant application in optoelectronics, biosensors, biological tracer and so on.

36 MATERIALS SCIENCE↗

Structural Analysis and Electrochemical Properties of Bimetallic Palladium-Platinum Aerogels Prepared by a Two-Step Gelation Process

Multimetallic aerogels have emerged as promising unsupported and high-surface-area metal materials for different applications in heterogeneous catalysis and electrochemistry, which are fabricated using a gelation process characterized by the controlled aggregation of metallic nanoparticles to form a macroscopic network structure in aqueous solution. However, the achievement of the structural homogeneity of the multimetallic aerogels in terms of the diameter of the nanochains and the chemical composition at the nano- and the macro-scale is still a great challenge. In this paper, we investigated two Pd-Pt aerogels prepared by the two-step gelation method. The structural homogeneity and chemical distribution of both metals inside the aerogels were analyzed by using high-resolution (scanning) transmission microscopy, energy-dispersive X-ray spectroscopy, extended X-ray absorption fine structure spectroscopy and cyclic voltammetry. The Pd-Pt aerogels show the presence of Pd/Pt-rich domains inside the long-range framework. It is evident that the initial monometallic features dominate over alloying during the gelation process. Although the same synthetic approach for Pd-Pt aerogels with different atomic ratios was used, we observed that the sizes of these monometallic domains varied strongly between the Pd-rich and Pt-rich aerogels. The presence of such metal clusters influenced the electrochemical robustness of the Pd-Pt aerogels dramatically. Further, electrochemical durability investigations revealed that the aerogels with a high content of Pd are less stable because of the gradual dissolution of the less noble metal particularly inside the Pd-rich domains. A chemical and structural homogeneity might improve the lifetime of the Pd-Pt aerogels under electrochemical conditions. In this work, we provide a better understanding of the structure and chemical distribution of the bimetallic aerogel framework prepared by the two-step gelation process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Deposition temperature dependence of material and Si surface passivation properties of O{sub 3}-based atomic layer deposited Al{sub 2}O{sub 3}-based films and stacks

The material composition and the Si surface passivation of aluminum oxide (Al{sub 2}O{sub 3}) films prepared by atomic layer deposition using Al(CH{sub 3}){sub 3} and O{sub 3} as precursors were investigated for deposition temperatures (T{sub Dep}) between 200 °C and 500 °C. The growth per cycle decreased with increasing deposition temperature due to a lower Al deposition rate. In contrast the material composition was hardly affected except for the hydrogen concentration, which decreased from [H] = 3 at. % at 200 °C to [H] < 0.5 at. % at 400 °C and 500 °C. The surface passivation performance was investigated after annealing at 300 °C–450 °C and also after firing steps in the typical temperature range of 800 °C–925 °C. A similar high level of the surface passivation performance, i.e., surface recombination velocity values <10 cm/s, was obtained after annealing and firing. Investigations of Al{sub 2}O{sub 3}/SiN{sub x} stacks complemented the work and revealed similar levels of surface passivation as single-layer Al{sub 2}O{sub 3} films, both for the chemical and field-effect passivation. The fixed charge density in the Al{sub 2}O{sub 3}/SiN{sub x} stacks, reflecting the field-effect passivation, was reduced by one order of magnitude from 3·10{sup 12} cm{sup −2} to 3·10{sup 11} cm{sup −2} when T{sub Dep} was increased from 300 °C to 500 °C. The level of the chemical passivation changed as well, but the total level of the surface passivation was hardly affected by the value of T{sub Dep}. When firing films prepared at of low T{sub Dep}, blistering of the films occurred and this strongly reduced the surface passivation. These results presented in this work demonstrate that a high level of surface passivation can be achieved for Al{sub 2}O{sub 3}-based films and stacks over a wide range of conditions when the combination of deposition temperature and annealing or firing temperature is carefully chosen.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ion Imaging Near a Reactive Surface

In this project, resonance enhanced multi-photon ionization followed by spatial mode ion imaging (REMPI-SMII) has been developed as a new tool for in-situ monitoring of local catalytic activity near a chemically active surface. A prototype experimental setup was developed for the demonstration, and initial results indicate this approach is feasible as a new diagnostic for online monitoring of catalytic reactions. The catalytic conversion of H 2 and D 2 to form HD over a Pt surface was carried out using a dual-molecular beam arrangement with reactant beams impinging on a structured Pt surface. The catalytic production of HD was successfully detected through the REMPI-SMII approach, and next steps were identified to improve the experimental design for better spatial resolution and mapping of catalytic surface activity.

47 OTHER INSTRUMENTATION↗

Influence of Atomic Surface Structure on the Activity of Ag for the Electrochemical Reduction of CO 2 to CO

This work was undertaken to elucidate the facet-dependent activity of Ag for the electrochemical reduction of CO 2 to CO. To this end, CO2 reduction was investigated over Ag thin films with (111), (100), and (110) orientations prepared via epitaxial growth on single-crystal Si wafers with the same crystallographic orientations. Thus, this preparation technique yielded larger area electrodes than can be achieved using single-crystals, which enabled the electrocatalytic activity of the corresponding Ag surfaces to be quantified in the Tafel regime. The Ag(110) thin films exhibited higher CO evolution activity compared to the Ag(111) and Ag(100) thin films, consistent with previous single-crystal studies. Density functional theory calculations suggest that CO 2 reduction to CO is strongly facet-dependent, and that steps are more active than highly coordinated terraces. This is the result of both a higher binding energy of the key intermediate COOH as well as an enhanced double-layer electric field stabilization over undercoordinated surface atoms located at step edge defects. As a consequence, step edge defects likely dominate the CO 2 reduction activity observed over the Ag(111) and Ag(100) thin films. The higher activity observed over the Ag(110) thin film is then related to the larger density of undercoordinated sites compared to the Ag(111) and Ag(100) thin films. Our conclusion that undercoordinated sites dominate the CO 2 reduction activity observed over close-packed surfaces highlights the need to consider the contribution of such defects in studies of single-crystal electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Two-Step Synthesis of Poly (urea formaldehyde) Microcapsules

Self-healing coatings have potential to reduce waste and minimize repair costs in industries where materials need to be protected from harsh environmental conditions and mechanical abrasion. These coatings can be created by embedding healing-agent filled microcapsules which release their contents and fill voids in the event of damage. To synthesize microcapsules that are ideal for self-healing coatings, they must have a diameter less than 100 microns, smooth surface morphology, and have improved dispersibility. Our current one-step method does not produce microcapsules within the desired size distribution, so a two-step route where oligomers of the shell wall material are formed prior to microcapsule formation was investigated. This was done by evaluating the effects of solution viscosity, size of reaction vessel, addition of poly (vinyl alcohol) (PVA), and core/shell ratio on microcapsule properties. Characterization of microcapsule size, morphology, and composition was done using optical microscopy, Fourier-transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). Microcapsules with an average diameter of 78 ± 16 microns were successfully synthesized. Further work must be done to minimize PUF crystallites on the surface of the microcapsules.

36 MATERIALS SCIENCE↗

Constructing MnO{sub 2}/single crystalline ZnO nanorod hybrids with enhanced photocatalytic and antibacterial activity

In order to improve the photocatalytic and antibacterial activity of ZnO nanorods, ZnO nanorods decorated with MnO{sub 2} nanoparticles (MnO{sub 2}/ZnO nanorod hybrids) were prepared by using microwave assisted coprecipitation method under the influence of hydrogen peroxide, and the structure, photocatalytic activity and antibacterial property of the products were studied. Experimental results indicated that MnO{sub 2} nanoparticles are decorated on the surface of single crystalline ZnO nanorods. Moreover, the resultant MnO{sub 2}/ZnO nanorod hybrids have been proven to possess good photocatalytic and antibacterial activity, which their degradated efficiency for Rhodamin B (RhB) is twice as the pure ZnO nanorods. Enhancement for photocatalytic and antibacterial activity is mainly attributed to the low band gap energy and excellent electrochemical properties of MnO{sub 2} nanoparticles. - Graphical abstract: The MnO{sub 2}/single crystalline ZnO nanorods hybrids, which MnO{sub 2} nanoparticles are loaded on the surface of ZnO nanorods, were prepared by the step-by-step precipitation method under the assistance of ammonia and hydrogen peroxide. Display Omitted - Highlights: • MnO{sub 2}/ZnO nanorod hybrids were prepared by the step-by-step assembly method. • Single crystalline ZnO nanorods can be decorated by MnO{sub 2} nanoparticles. • MnO{sub 2}/ZnO nanorod hybrids possess good photocatalytic and antibacterial activity. • MnO{sub 2} can improve the photocatalytic activity of ZnO nanorods under visible light.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Preliminary Study on Machining of Additively Manufactured Ti-6Al-4V

We report additively manufactured metals differ from their conventionally produced counterparts due to the inherent material inhomogeneity, porosity, and thermal stress induced by the process. These differences make the machining of additively manufactured metals more difficult and cause premature tool failure or unexpected surface finish at certain conditions. This study takes the first step to investigate and identify the causes of these issues, particularly for Ti-6Al-4V. Printed and wrought samples, as well as heat treatment effect, are compared in a dry cutting condition at a cutting speed of 90 m/min in terms of cutting power, vibration, temperature, and produced surface finish. The results show a lower cutting power and more vibration for as-printed Ti samples, indicating a less ductile microstructure and inclusion of pores. Heat treatment can eliminate these phenomena. There is no significant difference found in the produced surface finish at the current cutting condition.

36 MATERIALS SCIENCE↗

Investigation of Machinability of Additively Manufactured Ti-6Al-4V

Additively manufactured metals differ from their conventionally produced counterparts due to the inherent material inhomogeneity, porosity, and thermal stress induced by the process. These differences make the machining of additively manufactured metals more difficult and cause premature tool failure or unexpected surface finish at certain conditions. This study takes the first step to investigate and identify the causes of these issues, particularly for Ti-6Al-4V. Printed and wrought samples, as well as heat treatment effect, are compared in a dry cutting condition at a cutting speed of 90 m/min in terms of cutting power, vibration, temperature, and produced surface finish. The results show a lower cutting power and more vibration for as-printed Ti samples, indicating a less ductile microstructure and inclusion of pores. Heat treatment can eliminate these phenomena. There is no significant difference found in the produced surface finish at the current cutting condition.

Raval, Jay↗

Double patterning HSQ processes of zone plates for 10 nm diffraction limitedperformance

In e-beam lithography, fabrication of sub-20 nm dense structures is challenging. While there is a constant effort to develop higher resolution resist processes, the progress of increasing pattern density is slow. For zone plates, consisting of dense lines and spaces, the outermost zone width has been limited to slightly less than 20 nm due to effects such as low aerial image contrast, forward scattering, intrinsic resist resolution, and development issues. To circumvent these effects, we have successfully developed a new double patterning HSQ process, and as a result, we have fabricated zone plates of 10 and 12 nm using the process. We previously developed a double patterning process in which a dense zone plate pattern is sub-divided into two semi-isolated, complementary zone set patterns. These patterns are fabricated separately and then overlaid with high accuracy to yield the desired pattern. The key to success with this process is the accuracy of the overlay. For diffraction-limited zone plates, accuracy better than one-third of the smallest zone width is needed. In our previous work, the zone set patterns were formed using PMMA and gold electroplating, which were overlaid and aligned to the zero-level mark layer with sub-pixel accuracy using our internally developed algorithm. The complete zone plate fabrication was conducted in-house. With this process, we successfully fabricated zone plates of 15 nm outermost zone. Using this zone plate, we were able to achieve sub-15 nm resolution at 1.52 nm wavelength, the highest resolution ever demonstrated in optical microscopy at that time. We attempted to extend the process to fabricating 12 nm and smaller zones. However, the modest PMMA contrast, combined with a relatively large electron beam size compared to the target feature sized limited the process latitude. To overcome this problem, we developed a new overlay process based on high resolution negative tone resist of hydrogen silsesquioxane (HSQ). With the development in TMAH at 45 C, we can reliably achieve zone width as small as 8 nm with negligible line edge roughness in the semi-dense zone set. Such narrow zones in HSQ, however, detach easily from the gold plating base substrate needed for the electroplating step. We developed a process to condition the gold substrate with (3-mercaptopropyl) trimethoxysilane, or 3-MTP, which can form a homogeneous hydroxylation surface on gold surface and bond with hydroxyl in HSQ. Fig 2 shows the basic process steps of the double patterning HSQ process. Unlike the PMMA process, both zone sets are formed in HSQ and overlaid, and the complete zone plate pattern is converted to gold using electroplating in the final step. Using the new process, we successfully realized zone plates of 10 nm and 12 nm outermost zones. Fig. 3 shows the SEM micrographs of the zone plates outer regions. The zone plates are 30 nm thick in gold. To the best of our knowledge, these zone plates have the smallest zonal features ever fabricated using e-beam lithography. The complete zone plate fabrication was conducted in-house, using our vector scan electron beam lithography tool, the Nanowriter, which has a measured beam diameter of 6.5 nm (FWHM) at 100 keV. An internally developed, sub-pixel alignment algorithm, based on auto/cross-correlation methods, was used for the overlay. A 12 nm zone plate was tested with a full-field transmission x-ray microscope at the LBNL's Advanced Light Source. Fig. 4 shows an x-ray image of a 40 nm thick gold radial spoke pattern taken with the zone plate at 1.75 nm wavelength (707eV, FeL3 edge), along with the scanning transmission electron micrograph of same object. Numerous small features in the object can be seen in the x-ray image. Data analysis indicates that a near diffraction limited performance was achieved using the zone plate. In our presentation, we will discuss the details and subtleties of the overlay fabrication as well as the zone plate image results.

36 MATERIALS SCIENCE↗

Thermodynamic Stability of Low- and High-Index Spinel LiMn 2 O 4 Surface Terminations

Density functional theory calculations are performed within the generalized gradient approximation (GGA+U) to determine stable terminations of both low- and high-index spinel LiMn2O4 (LMO) surfaces. A grand canonical thermodynamic approach is employed, permitting a direct comparison of offstoichiometric surfaces with previously reported stoichiometric surface terminations at various environmental conditions. Within this formalism, we have identified trends in the structure of the low-index surfaces as a function of the Li and O chemical potentials. The results suggest that, under a range of chemical potentials for which bulk LMO is stable, Li/O and Li-rich (111) surface terminations are favored, neither of which adopts an inverse spinel structure in the subsurface region. This thermodynamic analysis is extended to identify stable structures for certain high-index surfaces, including (311), (331), (511), and (531), which constitute simple models for steps or defects that may be present on real LMO particles. The low- and high-index results are combined to determine the relative stability of each surface facet under a range of environmental conditions. The relative surface energies are further employed to predict LMO particle shapes through a Wulff construction approach, which suggests that LMO particles will adopt either an octahedron or a truncated octahedron shape at conditions in which LMO is thermodynamically stable. These results are in agreement with the experimental observations of LMO particle shapes.

DFT↗