Search NASA⌕ Search

SEARCH · Search NASA

Results for “three dimensional models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Strain energy of thermally stressed multilayer panels and its sensitivity coefficients

A study is made of the effect of lamination and material parameters of thermally stressed multilayer composite panels on the strain energy and its sensitivity coefficients obtained by the three-dimensional thermoelasticity model. The sensitivity coefficients measure the sensitivity of the strain energy to variations in the different lamination and material parameters of the panel. The strain energy and sensitivity coefficients obtained by the three-dimensional model are used as the basis for assessing the accuracy of the corresponding quantities obtained by two-dimensional first-order shear deformation theory. Numerical results are presented for antisymmetrically laminated angle-ply panels subjected to linear temperature variation through the thickness. The numerical results demonstrate the accuracy of the strain energy and its sensitivity coefficients obtained by the first-order shear deformation theory, for the range of parameters considered, and the importance of the particular terms in the strain energy, which vanish for single-layer panels.

Noor, Ahmed K.↗

Analysis of holographic interferograms of aerodynamic models in a wind tunnel

Holographic interferometry provides a non-invasive technique for estimating variations in the air density distribution around aerodynamic models in wind tunnels. The testing of this technique has been underway for some time and has been reported previously for a two dimensional aerodynamic model. Results obtained from tests using three dimensional aerodynamic models are summarized. Holograms were made of aerodynamic models in a wind tunnel. Interferograms were made from these holograms. The interference fringes in these holographic interferograms were digitized and this information was entered into the HOLOFT program. The HOLOFT program successfully calculated the known stagnation air density at the nose of a model and the known air density distribution across the cross section passing through the stagnation point for the axisymmetrical case of this model at a Mach number of 0.8. Thus the technique of holographic interferometry does work.The HOLOFT program stands for HOLOgraphic Inversion by 2-D Fourier Transform.

Perry, R. L.↗

Moment tensor reconstruction

A seismic monitoring system includes a plurality of seismic monitors and a processing device operatively coupled to the plurality of seismic monitors. The processing device receives recordings of waveforms of motion detected at the plurality of seismic detectors in a geographic area. The processing device applies the respective recordings to corresponding positions of the seismic detectors in a three-dimensional geological model that describes its elastic attributes and tests a plurality of moment tensors at a plurality of locations. Based on the testing, the processing device determines a globally convergent source location and moment tensor in the three-dimensional model based on the testing.

Petrov, Petr↗

An Integrated Magnetic Circuit Model and Finite Element Model Approach to Magnetic Bearing Design

A code for designing magnetic bearings is described. The code generates curves from magnetic circuit equations relating important bearing performance parameters. Bearing parameters selected from the curves by a designer to meet the requirements of a particular application are input directly by the code into a three-dimensional finite element analysis preprocessor. This means that a three-dimensional computer model of the bearing being developed is immediately available for viewing. The finite element model solution can be used to show areas of magnetic saturation and make more accurate predictions of the bearing load capacity, current stiffness, position stiffness, and inductance than the magnetic circuit equations did at the start of the design process. In summary, the code combines one-dimensional and three-dimensional modeling methods for designing magnetic bearings.

Provenza, Andrew J.↗

Variations in eddy diffusion and associated transport processes

Variation in the eddy diffusion coefficient constitutes a momentum source. This variation near the turbopause affects both the composition and the wind and temperature fields of the thermosphere. Two types of calculations are carried out, for horizontal winds considered self-consistently in a three-dimensional dynamic model and horizontal winds artificially suppressed to simulate a one-dimensional model. Momentum transfer associated with variations in eddy diffusion coefficients represents the source function in the analysis presented. It is shown that for long-term variations in the thermosphere, the compositional dependence on variations in eddy diffusion coefficients can be entirely different in one and three dimensional models with horizontal winds included. Horizontal winds can greatly reduce the effects of eddy diffusion in general and the ratio between He and O amplitudes in particular.

Mayr, H. G.↗

Three-dimensional, time-dependent, MHD model of a solar flare-generated interplanetary shock wave

A three-dimensional time-dependent MHD model of the propagation of an interplanetary shock wave into an ambient three-dimensional heliospheric solar wind is initialized with a peak velocity of 1000 km/s at the center of a right circular cone of 18 deg included angle at 18 solar radii. Differences from a previous 2-1/2 simulation (Wu et al., 1983; Gislason et al., 1984; Dryer et al., 1984) include diminuation of the solar peak velocity and concentration of the peak density at each radius. The IMF magnitude starts with high-latitude peaks, and helical-like IMF rotation is noted due to a large-amplitude nonlinear Alfven wave in the shocked plasma.

Dryer, M.↗

System maintenance manual for master modeling of aerodynamic surfaces by three-dimensional explicit representation

A system of computer programs has been developed to model general three-dimensional surfaces. Surfaces are modeled as sets of parametric bicubic patches. There are also capabilities to transform coordinate to compute mesh/surface intersection normals, and to format input data for a transonic potential flow analysis. A graphical display of surface models and intersection normals is available. There are additional capabilities to regulate point spacing on input curves and to compute surface intersection curves. Internal details of the implementation of this system are explained, and maintenance procedures are specified.

Gibson, A. F.↗

Evaluation of a surface panel method coupled with several boundary layer analyses

Three boundary layer models are interacted with an inviscid panel method to evaluate their capabilities to predict aerodynamic performance characteristics. These boundary layer models include two two-dimensional boundary layer models and one three-dimensional boundary layer model. Previously reported discrepancies between the transpiration and surface displacement inviscid boundary layer simulations are discussed and resolved. Results from each of the models are compared with experimental data.

Kjelgaard, S. O.↗

A Three-Dimensional, Analytical Wind Turbine Wake Model: Flow Acceleration, Empirical Correlations, and Continuity

A new, three-dimensional, analytical, steady-state wake model is presented that includes local flow acceleration near the rotor, improving the wake description compared to existing models. Wake structures such as the momentum deficit and regions of accelerated flow are concisely described with compound and normal Gaussian functions. Large-eddy simulations (LES) are used as training data to develop the model using two in-line turbines under various inflow conditions parameterized by hub-height wind speed and turbulence intensity. Mass conservation is considered by fixing two components of the wake velocity model and optimizing the third to best satisfy continuity; after which, the model performs comparably if not better than existing work with regards to both relative error and mass consistency. The final model demonstrates a high degree of flexibility, making use of empirical correlations to scale across different inflow conditions. The inclusion of these effects is capable of revealing unused opportunities for enhanced power generation by aligning wake trajectories with these regions of accelerated flow.

modeling↗

Coupling a three-dimensional subsurface flow and transport model with a land surface model to simulate stream–aquifer–land interactions (CP v1.0)

A fully coupled three-dimensional surface and subsurface land model is developed and applied to a site along the Columbia River to simulate three-way interactions among river water, groundwater, and land surface processes. The model features the coupling of the Community Land Model version 4.5 (CLM4.5) and a massively parallel multiphysics reactive transport model (PFLOTRAN). The coupled model, named CP v1.0, is applied to a 400 m × 400 m study domain instrumented with groundwater monitoring wells along the Columbia River shoreline. CP v1.0 simulations are performed at three spatial resolutions (i.e., 2, 10, and 20 m) over a 5-year period to evaluate the impact of hydroclimatic conditions and spatial resolution on simulated variables. Results show that the coupled model is capable of simulating groundwater–river-water interactions driven by river stage variability along managed river reaches, which are of global significance as a result of over 30 000 dams constructed worldwide during the past half-century. Our numerical experiments suggest that the land-surface energy partitioning is strongly modulated by groundwater–river-water interactions through expanding the periodically inundated fraction of the riparian zone, and enhancing moisture availability in the vadose zone via capillary rise in response to the river stage change. Meanwhile, CLM4.5 fails to capture the key hydrologic process (i.e., groundwater–river-water exchange) at the site, and consequently simulates drastically different water and energy budgets. Furthermore, spatial resolution is found to significantly impact the accuracy of estimated the mass exchange rates at the boundaries of the aquifer, and it becomes critical when surface and subsurface become more tightly coupled with groundwater table within 6 to 7 meters below the surface. Inclusion of lateral subsurface flow influenced both the surface energy budget and subsurface transport processes as a result of river-water intrusion into the subsurface in response to an elevated river stage that increased soil moisture for evapotranspiration and suppressed available energy for sensible heat in the warm season. The coupled model developed in this study can be used for improving mechanistic understanding of ecosystem functioning and biogeochemical cycling along river corridors under historical and future hydroclimatic changes. The dataset presented in this study can also serve as a good benchmarking case for testing other integrated models.

58 GEOSCIENCES↗

Direct Numerical Simulation of Flow Past a Gaussian Bump at a High Reynolds Number

We present the results from a direct numerical simulation of a spanwise-periodic turbulent flow past a Gaussian bump. The problem setup is designed to investigate the interaction of an incoming turbulent boundary layer with the strong favorable and adverse pressure gradients generated by the Gaussian bump as the flow passes over it at a Reynolds number of 340000 based on the bump height, or 4 million based on the bump length. The statistical results from the present simulation are compared against our earlier results at a Reynolds number of 2 million. An internal layer, which forms beneath the strongly accelerated boundary layer over the windward side of the bump, is found to generate its near-wall turbulence stress peaks in closer proximity of the wall in the higher Reynolds-number case. Furthermore, the logarithmic layer of the higher Reynolds-number boundary layer appears more resistant to changes induced by strong acceleration and surface curvature effects over the same region. Despite a nearly identical flow separation point in the two flows, the detached shear layer grows at a faster rate and subsequently reattaches at an earlier point in the higher Reynolds-number flow. The surface pressure and skin-friction distributions over the attached flow region compare well against the corresponding experimental data for both flows. However, some differences appear in the separated flow region, which are attributed to the three-dimensionality of the experimental model setup that is not included in the simulation owing to the spanwise periodic assumption. Comparisons with the stereoscopic particle image velocimetry measurements on the central plane of the experimental model over the windward side of the bump show reasonable overall agreement in the mean velocity components, but the turbulence stress components do not agree well at some streamwise locations. Comparisons over the leeward side of the bump show that the mean separated shear layer in the simulation is tilted significantly more toward the wall than the experimental shear layer on the central plane. This mismatch in the mean shear layer orientation is due to the experimental model three-dimensionality and tunnel end-wall effects, which are not modeled in the present spanwise-periodic simulation.

Favorable and Adverse Pressure Gradients↗

Calculation of flow about posts and powerhead model

A three dimensional analysis of the non-uniform flow around the liquid oxygen (LOX) posts in the Space Shuttle Main Engine (SSME) powerhead was performed to determine possible factors contributing to the failure of the posts. Also performed was three dimensional numerical fluid flow analysis of the high pressure fuel turbopump (HPFTP) exhaust system, consisting of the turnaround duct (TAD), two-duct hot gas manifold (HGM), and the Version B transfer ducts. The analysis was conducted in the following manner: (1) modeling the flow around a single and small clusters (2 to 10) of posts; (2) modeling the velocity field in the cross plane; and (3) modeling the entire flow region with a three dimensional network type model. Shear stress functions which will permit viscous analysis without requiring excessive numbers of computational grid points were developed. These wall functions, laminar and turbulent, have been compared to standard Blasius solutions and are directly applicable to the cylinder in cross flow class of problems to which the LOX post problem belongs.

Anderson, P. G.↗

THREE-DIMENSIONAL KINETIC-MHD MODEL OF THE GLOBAL HELIOSPHERE WITH THE HELIOPAUSE-SURFACE FITTING

This paper provides a detailed description of the latest version of our model of the solar wind (SW) interaction with the local interstellar medium (LISM). This model has already been applied to the analysis of Lyα absorption spectra toward nearby stars and for analyses of Solar and Heliospheric Observatory/SWAN data. Katushkina et al. (this issue) used the model results to analyze IBEX-Lo data. At the same time, the details of this model have not yet been published. This is a three-dimensional (3D) kinetic-magnetohydrodynamical (MHD) model that takes into account SW and interstellar plasmas (including α particles in SW and helium ions in LISM), the solar and interstellar magnetic fields, and interstellar hydrogen atoms. The latitudinal dependence of SW and the actual flow direction of the interstellar gas with respect to the Sun are also taken into account in the model. It was very essential that our numerical code was developed in such a way that any numerical diffusion or reconnection across the heliopause were not allowed in the model. The heliospheric current sheet is a rotational discontinuity in the ideal MHD and can be treated kinematically. In the paper, we focus in particular on the effects of the heliospheric magnetic field and on the heliolatitudinal dependence of SW.

79 ASTRONOMY AND ASTROPHYSICS↗

Application of the kappa-omega Turbulence Model to Quasi-Three-Dimensional Turbomachinery Flows

Many computational fluid dynamics codes for turbomachinery use the Baldwin-Lomax (B-L) turbulence model. It is easy to implement in two dimensions and works well for predicting overall turbomachinery performance. However, it is awkward to implement in three dimensions, often has difficulty finding the length scale, has a crude transition model, and neglects freestream turbulence, surface roughness, and mass injection. The kappa-omega model developed by Wilcox is an appealing alternative for several reasons. First, it is the only two-equation model that can be integrated to the wall without requiring damping functions or the distance to the wall, and hence, should behave well numerically. Second, the effects of freestream turbulence, surface roughness, and mass injection are easily included in the model. Finally, transition can be simulated using the low Reynolds number version of the model. Menter applied the kappa-model to external flows and showed very good results for flows with adverse pressure gradients. Liu and Zheng described their implementation of the kappa-model in a cascade code that included an area change term to account for endwall convergence. They validated the model for a flat plate, and compared the B-L and kappa-models to measured surface pressures for a low-pressure turbine cascade. Since they did not use the low Reynolds number version of the model, their results showed problems resulting from early transition. In this Note the low Reynolds number kappa-model was incorporated in the author's quasi-three-dimensional turbomachinery analysis code. The code includes the effects of rotation, radius change, and stream-surface thickness variation, and also includes the B-L turbulence model. The kappa-omega model was implemented using many of Menter's recommendations and an implicit approximate-factorization scheme described by Baldwin and Barth. The model was tested for a transonic compressor with rotation and variable stream-surface radius and height, and for a transonic turbine vane with transition and heat transfer. Results were compared to the B-L model and to experimental data.

Chima, Rodrick V.↗

Analysis of Composite Skin-Stiffener Debond Specimens Using Volume Elements and a Shell/3D Modeling Technique

The debonding of a skin/stringer specimen subjected to tension was studied using three-dimensional volume element modeling and computational fracture mechanics. Mixed mode strain energy release rates were calculated from finite element results using the virtual crack closure technique. The simulations revealed an increase in total energy release rate in the immediate vicinity of the free edges of the specimen. Correlation of the computed mixed-mode strain energy release rates along the delamination front contour with a two-dimensional mixed-mode interlaminar fracture criterion suggested that in spite of peak total energy release rates at the free edge the delamination would not advance at the edges first. The qualitative prediction of the shape of the delamination front was confirmed by X-ray photographs of a specimen taken during testing. The good correlation between prediction based on analysis and experiment demonstrated the efficiency of a mixed-mode failure analysis for the investigation of skin/stiffener separation due to delamination in the adherents. The application of a shell/3D modeling technique for the simulation of skin/stringer debond in a specimen subjected to three-point bending is also demonstrated. The global structure was modeled with shell elements. A local three-dimensional model, extending to about three specimen thicknesses on either side of the delamination front was used to capture the details of the damaged section. Computed total strain energy release rates and mixed-mode ratios obtained from shell/3D simulations were in good agreement with results obtained from full solid models. The good correlations of the results demonstrated the effectiveness of the shell/3D modeling technique for the investigation of skin/stiffener separation due to delamination in the adherents.

Krueger, Ronald↗

Coupling a three-dimensional subsurface flow and transport model with a land surface model to simulate stream–aquifer–land interactions (CP v1.0)

Abstract. A fully coupled three-dimensional surface and subsurface land model is developed and applied to a site along the Columbia River to simulate three-way interactions among river water, groundwater, and land surface processes. The model features the coupling of the Community Land Model version 4.5 (CLM4.5) and a massively parallel multiphysics reactive transport model (PFLOTRAN). The coupled model, named CP v1.0, is applied to a 400 m × 400 m study domain instrumented with groundwater monitoring wells along the Columbia River shoreline. CP v1.0 simulations are performed at three spatial resolutions (i.e., 2, 10, and 20 m) over a 5-year period to evaluate the impact of hydroclimatic conditions and spatial resolution on simulated variables. Results show that the coupled model is capable of simulating groundwater–river-water interactions driven by river stage variability along managed river reaches, which are of global significance as a result of over 30 000 dams constructed worldwide during the past half-century. Our numerical experiments suggest that the land-surface energy partitioning is strongly modulated by groundwater–river-water interactions through expanding the periodically inundated fraction of the riparian zone, and enhancing moisture availability in the vadose zone via capillary rise in response to the river stage change. Meanwhile, CLM4.5 fails to capture the key hydrologic process (i.e., groundwater–river-water exchange) at the site, and consequently simulates drastically different water and energy budgets. Furthermore, spatial resolution is found to significantly impact the accuracy of estimated the mass exchange rates at the boundaries of the aquifer, and it becomes critical when surface and subsurface become more tightly coupled with groundwater table within 6 to 7 meters below the surface. Inclusion of lateral subsurface flow influenced both the surface energy budget and subsurface transport processes as a result of river-water intrusion into the subsurface in response to an elevated river stage that increased soil moisture for evapotranspiration and suppressed available energy for sensible heat in the warm season. The coupled model developed in this study can be used for improving mechanistic understanding of ecosystem functioning and biogeochemical cycling along river corridors under historical and future hydroclimatic changes. The dataset presented in this study can also serve as a good benchmarking case for testing other integrated models.

58 GEOSCIENCES↗