Search NASA⌕ Search

SEARCH · Search NASA

Results for “Catalyst”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

CATALYST AMMONIA STORAGE MEASUREMENTS USING RADIO FREQUENCY SENSING

Motivated by increasingly strict NO x limits, engine manufactures have adopted selective catalytic reduction (SCR) technology to reduce engine-out NO x below mandated levels. In the SCR process, nitrogen oxides (NO x ) react with ammonia (NH 3 ) to form nitrogen and water vapor. The reaction is influenced by several variables, including stored ammonia on the catalyst, exhaust gas composition, and catalyst temperature. Currently, measurements from NO x and/or NH 3 sensors upstream and downstream of the SCR are used with predictive models to estimate ammonia storage levels on the catalyst and control urea dosing. This study investigated a radio frequency (RF) -based method to directly monitor the ammonia storage state of the SCR catalyst. This approach utilizes the SCR catalyst as a cavity resonator, in which an RF antenna excites electromagnetic waves within the cavity to monitor changes in the catalyst state. Ammonia storage causes changes in the dielectric properties of the catalyst, which directly impacts the RF signal. Changes in the RF signal relative to stored ammonia (NH 3 ) were evaluated over a wide frequency range as well as temperature and exhaust conditions. The RF response to NH 3 storage, desorption, and oxidation on the SCR was observed to be well-correlated with changes in the catalyst state. Calibrated RF measurements demonstrate the ability to monitor the adsorption state of the SCR to within 10 % of the sensor full scale. The results indicate direct measurement of SCR ammonia storage levels, and resulting catalyst feedback control, via RF sensing to have significant potential for optimizing the SCR system to improve NO x conversion and decrease urea consumption.

Aguilar, Jonathan↗

Stability of Atomically Dispersed Fe–N–C ORR Catalyst in Polymer Electrolyte Fuel Cell Environment

We have investigated the durability of a platinum group metal (PGM-)free Fe–N–C catalyst in which the Fe sites are atomically dispersed (AD), and found it to be quite stable in standard accelerated stress test (AST) cycles normally used for low-PGM catalysts: a square wave with 0.6 V lower potential limit (LPL)—0.95 V upper potential limit (UPL) with 3-s holds at UPL and LPL in H 2 /N 2 , at 1.5 atm, 80 °C and 100% RH. Considering the metrics normally employed to characterize the durability of the low-PGM catalysts after 30,000 AST cycles, this PGM-free catalyst lost <50% catalyst activity, <50% H 2 /air performance at 0.8 V, and 40 mV at 1.5 A cm -2 . However, it is less stable in H 2 /air, losing ~50% catalyst activity after just 7.5 h of polarization measurements (load cycles). In combined cycles, the majority of the loss in catalyst activity occurred during the load cycles in H 2 /air rather than AST cycles in H 2 /N 2 . We have concluded that, unlike low-PGM catalysts that lose electrochemically active surface area (ECSA) through potential cycling-induced processes, (AD)Fe–N–C catalysts degrade by processes associated with the presence of oxygen.

25 ENERGY STORAGE↗

Development of GREET Catalyst Module

Catalysts are critical inputs for many pathways that convert biomass into biofuels. Energy consumption and greenhouse gas (GHG) emissions during the production of catalysts and chemical inputs influence the life-cycle energy consumption, and GHG emissions of biofuels and need to be considered in biofuel life-cycle analysis (LCA). In this report, we develop energy and material flows for the production of three different catalysts (tar reforming, alcohol synthesis, Zeolite Socony Mobil-5 [ZSM-5]) and two chemicals (olivine, dimethyl ether of polyethylene glycol [DEPG]). These compounds and catalysts are now included in the Greenhouse Gases, Regulated Emissions and Energy Use in Transportation (GREET™) catalyst module. They were selected because they are consumed in existing U.S. Department of Energy (DOE) analyses of biofuel processes. For example, a thermochemical ethanol production pathway (indirect gasification and mixed alcohol synthesis) developed by the National Renewable Energy Laboratory (NREL) uses olivine, DEPG, and tar reforming and alcohol synthesis catalysts (Dutta et al., 2011). ZSM-5 can be used in biofuel production pathways such as catalytic upgrading of sugars into hydrocarbons (Biddy and Jones, 2013). Other uses for these compounds and catalysts are certainly possible. In this report, we document the data sources and methodology we used to develop material and energy flows for the catalysts and compounds in the GREET catalyst module. In Section 2 we focus on compounds used in the model Dutta et al. (2011) developed. In Section 3, we report material and energy flows associated with ZSM-5 production. Finally, in Section 4, we report results.

09 BIOMASS FUELS↗

Final Technical Report for project entitled Highly Active, Durable, and Ultra-Low PGM NSTF Thin Film ORR Catalysts and Support

In this project, the objective was to develop new oxygen reduction reaction (ORR) electrocatalysts for proton exchange membrane fuel cells (PEMFCs) which could exceed all of the Department of Energy (DOE) 2020 targets listed in DE-FOA-0001224, Subtopic 1b, Table I. The expected outcome was development of one or more electrocatalysts which are substantially improved over the current state-of-the-art in terms of overall activity, durability, and cost, and are suitable for automotive traction and stationary fuel cell applications. This report summarizes this project’s progress towards meeting the stated objectives and includes a summary of key findings and conclusions. The development activities towards new highly active and durable thin film electrocatalysts has led to the discovery of several electrocatalysts which approached or exceeded several DOE 2020 targets for activity, durability, and performance in proton exchange membrane fuel cell (membrane electrode assemblies (MEAs). In this project, electrocatalyst development focused on systematic physical and electrochemical characterization of electrocatalyst activity, durability, and performance in MEAs as a function of electrocatalyst fabrication, compositional and structural variables. The project approach was to develop relationships between the catalyst functional responses (activity, durability and performance) with catalyst physical properties and catalyst fabrication methods. Additionally, the thin film catalysts were integrated onto the unique and durable 3M Nanostructured Thin Film (NSTF) support, consisting of arrays of self-assembled organic crystalline whiskers. The catalysts were evaluated against the project targets via extensive electrochemical characterization in MEA format at 3M, advanced structural and compositional microscopy at Oak Ridge National Laboratory (ORNL), and atomic structure analysis via XAFS at Argonne National Laboratory (ANL). The extensive electrochemical and physical characterization resulted in development of several trends which correlate the catalysts’ electrochemical properties to their physical properties, including composition, structure, and method of fabrication. The development was guided by density functional theory (DFT) modeling at Purdue University and kinetic Monte Carlo (kMC) modeling at Johns Hopkins University. The catalyst simulations provided key insights into the observed experimental activity and durability trends, and additionally were utilized to assess new electrocatalyst concepts prior to or coincident with physical catalyst development. This development has led to several electrocatalyst candidates with activity and durability which approach or exceed DOE targets. One class of catalysts, based on nm-scale thin layers of Pt on Ir, met or exceeded 6 of the 6 DOE targets the project addressed.

08 HYDROGEN↗

Promoted Ru/PrOx Catalysts for Mild Ammonia Synthesis

Ammonia synthesis is one of the most important chemical reactions. Due to thermodynamic restrictions and the reaction requirements of the current commercial iron catalysts, it is also one of the worst reactions for carbon dioxide emissions and energy usage. Ruthenium-based catalysts can substantially improve the environmental impact as they operate at lower pressures and temperatures. In this work, we provide a screening of more than 40 metals as possible promoter options based on a Ru/Pr2O3 catalyst. Cesium was the best alkali promoter and was held constant for the series of double-promoted catalysts. Ten formulations outperformed the Ru-Cs/PrOx benchmark, with barium being the best second promoter studied and the most cost-effective option. Designs of experiments were utilized to optimize both the pretreatment conditions and the promoter weight loadings of the doubly promoted catalyst. As a result, optimization led to a more than five-fold increase in activity compared to the unpromoted catalyst, therefore creating the possibility for low-ruthenium ammonia synthesis catalysts to be used at scale. Further, we have explored the roles of promoters using kinetic analysis, X-ray Photoelectron Spectroscopy (XPS), and in situ infrared spectroscopy. Here, we have shown that the role of barium is to act as a hydrogen scavenger and donor, which may permit new active sites for the catalyst, and have demonstrated that the associative reaction mechanism is likely used for the unpromoted Ru/PrOx catalyst with hydrogenation of the triple bond of the dinitrogen occurring before any dinitrogen bond breakage.

Chemistry↗

Fischer-Tropsch Synthesis: The Characterization and Testing of Pt-Co/SiO 2 Catalysts Prepared with Alternative Cobalt Precursors

Different low-cost cobalt precursors (acetate, chloride) and thermal treatments (air calcination/H 2 reduction versus direct H 2 -activation) were investigated to alter the interaction between cobalt and silica. H 2 -activated catalysts prepared from cobalt chloride had large Co 0 particles (XRD, chemisorption) formed by weak interactions between cobalt chloride and silica (temperature programmed reduction (TPR), TPR with mass spectrometry (TPR-MS), TPR with extended X-ray absorption fine structure (EXAFS) and X-ray absorption near edge spectroscopy (XANES) techniques) and retained Cl-blocked active sites, resulting in poor activity. In contrast, unpromoted Co/SiO 2 catalysts derived from cobalt acetate had strong interactions between Co species and silica (TPR/TPR-MS, TPR-EXAFS/XANES); adding Pt increased the extent of the Co reduction. For these Pt-promoted catalysts, the reduction of uncalcined catalysts was faster, resulting in larger Co 0 clusters (19.5 nm) in comparison with the air-calcined/H 2 -activated catalyst (7.8 nm). Both catalysts had CO conversions 25% higher than that of the Pt-promoted catalyst prepared in the traditional manner (air calcination/H 2 reduction using cobalt nitrate) and three times higher than that of the traditional unpromoted Co/silica catalyst. The retention of residual cobalt carbide (observed in XANES) from cobalt acetate decomposition impacted performance, resulting in a higher C 1 –C 4 selectivity (32.2% for air-calcined and 38.7% for uncalcined) than that of traditional catalysts (17.5–18.6%). The residual carbide also lowered the α-value and olefin/paraffin ratio. Future work will focus on improving selectivity through oxidation–reduction cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Catalyst for Carbon Monoxide Oxidation

In many applications, it is highly desirable to operate a CO2 laser in a sealed condition, for in an open system the laser requires a continuous flow of laser gas to remove the dissociation products that occur in the discharge zone of the laser, in order to maintain a stable power output. This adds to the operating cost of the laser, and in airborne or space applications, it also adds to the weight penalty of the laser. In a sealed CO2 laser, a small amount of CO2 gas is decomposed in the electrical discharge zone into corresponding quantities of CO and O2. As the laser continues to operate, the concentration of CO2 decreases, while the concentrations of CO and O2 correspondingly increase. The increasing concentration of O2 reduces laser power, because O2 scavenges electrons in the electrical discharge, thereby causing arcing in the electric discharge and a loss of the energetic electrons required to boost CO2 molecules to lasing energy levels. As a result, laser power decreases rapidly. The primary object of this invention is to provide a catalyst that, by composition of matter alone, contains chemisorbed water within and upon its structure. Such bound moisture renders the catalyst highly active and very long-lived, such that only a small quantity of it needs to be used with a CO2 laser under ambient operating conditions. This object is achieved by a catalyst that consists essentially of about 1 to 40 percent by weight of one or more platinum group metals (Pt, Pd, Rh, Ir, Ru, Os, Pt being preferred); about 1 to 90 percent by weight of one or more oxides of reducible metals having multiple valence states (such as Sn, Ti, Mn, Cu, and Ce, with SnO2 being preferred); and about 1 to 90 percent by weight of a compound that can bind water to its structure (such as silica gel, calcium chloride, magnesium sulfate, hydrated alumina, and magnesium perchlorate, with silica gel being preferred). Especially beneficial results are obtained when platinum is present in the catalyst composition in an amount of about 5 to 25 (especially 7) percent by weight, SnO2 is present in an amount of about 30 to 40 (especially 40) percent by weight, and silica gel is present in an amount of 45 to 55 (especially 50) percent by weight. The composition of this catalyst was suggested by preliminary experiments in which a Pt/SnO2 catalyst was needed for bound water to enhance its activity. These experimental results suggested that if the water were bound to the surface, this water would enhance and prolong catalyst activity for long time periods. Because the catalyst is to be exposed to a laser gas mixture, and because a CO2 laser can tolerate only a very small amount of moisture, a hygroscopic support for the catalyst would provide the needed H2O into the gas. Silica gel is considered to be superior because of its property to chemisorb water on its surface over a wide range of moisture content.

Davis, Patricia↗

The Bosch Process-Performance of a Developmental Reactor and Experimental Evaluation of Alternative Catalysts

Bosch-based reactors have been in development at NASA since the 1960's. Traditional operation involves the reduction of carbon dioxide with hydrogen over a steel wool catalyst to produce water and solid carbon. While the system is capable of completely closing the loop on oxygen and hydrogen for Atmosphere Revitalization, steel wool requires a reaction temperature of 650C or higher for optimum performance. The single pass efficiency of the reaction over steel wool has been shown to be less than 10% resulting in a high recycle stream. Finally, the formation of solid carbon on steel wool ultimately fouls the catalyst necessitating catalyst resupply. These factors result in high mass, volume and power demands for a Bosch system. Interplanetary transportation and surface exploration missions of the moon, Mars, and near-earth objects will require higher levels of loop closure than current technology cannot provide. A Bosch system can provide the level of loop closure necessary for these long-term missions if mass, volume, and power can be kept low. The keys to improving the Bosch system lie in reactor and catalyst development. In 2009, the National Aeronautics and Space Administration refurbished a circa 1980's developmental Bosch reactor and built a sub-scale Bosch Catalyst Test Stand for the purpose of reactor and catalyst development. This paper describes the baseline performance of two commercially available steel wool catalysts as compared to performance reported in the 1960's and 80's. Additionally, the results of sub-scale testing of alternative Bosch catalysts, including nickel- and cobalt-based catalysts, are discussed.

Abney, Morgan B.↗

Life Support Catalyst Regeneration Using Ionic Liquids and In Situ Resources

Oxygen recovery from metabolic carbon dioxide is an enabling capability for long-duration manned space flight. Complete recovery of oxygen (100%) involves the production of solid carbon. Catalytic approaches for this purpose, such as Bosch technology, have been limited in trade analyses due in part to the mass penalty for high catalyst resupply caused by carbon fouling of the iron or nickel catalyst. In an effort to mitigate this challenge, several technology approaches have been proposed. These approaches have included methods to prolong the life of the catalysts by increasing the total carbon mass loading per mass catalyst, methods for simplified catalyst introduction and removal to limit the resupply container mass, methods of using in situ resources, and methods to regenerate catalyst material. Research and development into these methods is ongoing, but only use of in situ resources and/or complete regeneration of catalyst material has the potential to entirely eliminate the need for resupply. The use of ionic liquids provides an opportunity to combine these methods in a technology approach designed to eliminate the need for resupply of oxygen recovery catalyst. Here we describe the results of an initial feasibility study using ionic liquids and in situ resources for life support catalyst regeneration, we discuss the key challenges with the approach, and we propose future efforts to advance the technology.

Abney, Morgan B.↗

Life Support Catalyst Regeneration Using Ionic Liquids and In Situ Resources

Oxygen recovery from metabolic carbon dioxide is an enabling capability for long-duration manned space flight. Complete recovery of oxygen (100%) involves the production of solid carbon. Catalytic approaches for this purpose, such as Bosch technology, have been limited in trade analyses due in part to the mass penalty for high catalyst resupply caused by carbon fouling of the iron or nickel catalyst. In an effort to mitigate this challenge, several technology approaches have been proposed. These approaches have included methods to prolong the life of the catalysts by increasing the total carbon mass loading per mass catalyst, methods for simplified catalyst introduction and removal to limit the resupply container mass, methods of using in situ resources, and methods to regenerate catalyst material. Research and development into these methods is ongoing, but only use of in situ resources and/or complete regeneration of catalyst material has the potential to entirely eliminate the need for resupply. The use of ionic liquids provides an opportunity to combine these methods in a technology approach designed to eliminate the need for resupply of oxygen recovery catalyst. Here we describe the results of an initial feasibility study using ionic liquids and in situ resources for life support catalyst regeneration, we discuss the key challenges with the approach, and we propose future efforts to advance the technology.

Abney, Morgan B.↗

Photo-oxidation catalysts

Photo-oxidation catalysts and methods for cleaning a metal-based catalyst are disclosed. An exemplary catalyst system implementing a photo-oxidation catalyst may comprise a metal-based catalyst, and a photo-oxidation catalyst for cleaning the metal-based catalyst in the presence of light. The exposure to light enables the photo-oxidation catalyst to substantially oxidize absorbed contaminants and reduce accumulation of the contaminants on the metal-based catalyst. Applications are also disclosed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Oxidation catalyst

The present invention generally relates to catalyst systems and methods for oxidation of carbon monoxide. The invention involves catalyst compositions which may be advantageously altered by, for example, modification of the catalyst surface to enhance catalyst performance. Catalyst systems of the present invention may be capable of performing the oxidation of carbon monoxide at relatively lower temperatures (e.g., 200 K and below) and at relatively higher reaction rates than known catalysts. Additionally, catalyst systems disclosed herein may be substantially lower in cost than current commercial catalysts. Such catalyst systems may be useful in, for example, catalytic converters, fuel cells, sensors, and the like.

Ceyer, Sylvia T↗

Atomic Layer Deposition for Improved Biomass Conversion Catalysts

Heterogeneous catalysts are a key enabler of the transition towards a sustainable, bio-based economy for fuels and chemicals. However, the harsh conditions in many biomass conversion processes lead to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Next-generation catalysts must be developed to address these stability challenges. This presentation will discuss ongoing work between the Catalytic Carbon Transformation and Scale-Up Center at NREL and various industrial partners to develop scalable and cost-effective atomic layer deposition (ALD) coatings for improving the performance of biomass conversion catalysts. The substantial focus will be devoted to the benefits of TiO2 ALD coatings on supported Pd hydrogenation catalysts. Ten cycles of TiO2 ALD were found to dramatically improve the activity of a conventional Pd/Al2O3 catalyst towards aromatic hydrogenation, despite partial coverage of the Pd sites by the ALD layer. Subsequent advanced characterization and atomic-scale computational modeling revealed that the ALD coating weakened the adsorption strength of hydrogenation surface intermediates, leading to higher reaction rates. Reaction testing after exposure to sulfur impurities, high temperature oxidation, and hydrothermal treatment demonstrated the improved stability of the ALD-coated catalyst. Additionally, the ALD synthesis process was found to be scalable over two orders of magnitude with minimal deviation in synthesized catalyst properties. These results were contextualized with cost models of industrial ALD coating and aromatic hydrogenation processes to further refine the value proposition of ALD coatings. Given the demonstrated improvements in hydrogenation, TiO2 ALD coatings have also been applied to supported Pt catalysts for use in other biomass conversion reactions, such as hydrodeoxygenation for the production of sustainable aviation fuel (SAF) and the oxidation of glucose to bio-derived gluconic acid.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Layered catalyst structures and methods of making the same

A layered catalyst structure for purifying an exhaust gas stream includes a catalyst support and a palladium catalyst layer including an atomic dispersion of palladium ions electrostatically adsorbed onto an exterior surface of the catalyst support. The catalyst support includes an alumina substrate, a first ceria layer disposed on and extending substantially continuously over the alumina substrate, and a second colloidal ceria layer formed directly on the first ceria layer over the alumina substrate. The palladium catalyst layer is formed on the exterior surface of the catalyst support by applying a palladium-containing precursor solution to the exterior surface of the catalyst support and then heating the catalyst support and the palladium-containing precursor solution. The palladium-containing precursor solution includes a positively charged palladium complex in an aqueous medium and has a pH greater than a point of zero charge of the second colloidal ceria layer.

Gu, Yuntao↗

Pt/TiO2 (Rutile) Catalysts for Sulfuric Acid Decomposition in Sulfur-Based Thermochemical Water-Splitting Cycles

Thermochemical cycles consist of a series of chemical reactions to produce hydrogen from water at lower temperatures than by direct thermal decomposition. All the sulfur-based cycles for water splitting employ the sulfuric acid decomposition reaction. This work reports the studies performed on platinum supported on titania (rutile) catalysts to investigate the causes of catalyst deactivation under sulfuric acid decomposition reaction conditions. Samples of 1 wt% Pt/TiO2 (rutile) catalysts were submitted to flowing concentrated sulfuric acid at 1123 K and atmospheric pressure for different times on stream (TOS) between 0 and 548 h. Post-operation analyses of the spent catalyst samples showed that Pt oxidation and sintering occurred under reaction conditions and some Pt was lost by volatilization. Pt loss rate was higher at initial times but total loss appeared to be independent of the gaseous environment. Catalyst activity showed an initial decrease that lasted for about 66 h, followed by a slight recovery of activity between 66 and 102 h TOS, and a period of slower deactivation after 102 h TOS. Catalyst sulfation did not seem to be detrimental to catalyst activity and the activity profile suggested that a complex dynamical situation involving platinum sintering, volatilization, and oxidation, along with TiO2 morphological changes affected catalyst activity in a non-monotonic way.

08 HYDROGEN↗

Excellent Sulfur Resistance of Pt/BaO/CeO2 Lean NOx Trap Catalysts

In this work, we investigated the NOx storage behavior of Pt-BaO/CeO2 catalysts, especially in the presence of SO2. High surface area CeO2 (~ 110 m2/g) with a rod like morphology was synthesized and used as a support. The Pt-BaO/CeO2 sample demonstrated slightly higher NOx conversion in the entire temperature range studied compared with Pt-BaO/γ-Al2O3. More importantly, this ceria-based catalyst showed higher sulfur tolerance than the alumina-based one. The time of complete NOx uptake was maintained even after exposing the sample to ~3 g/L of SO2. The same sulfur exposure, on the other hand, eliminated the complete NOx uptake time on the alumina-based NOx storage catalysts. TEM images show no evidence of either Pt sintering or BaS phase formation during reductive de-sulfation up to 600°C on the ceria based catalyst, while the same process over the alumina-based catalyst resulted in both a significant increase in the average Pt cluster size and the agglomeration of a newly-formed BaS phase into large crystallites. XPS results revealed the presence of about 5 times more residual sulfur after reductive de-sulfation at 600°C on the alumina based catalysts in comparison with the ceria-based ones. All of these results strongly support that, besides their superior intrinsic NOx uptake properties, ceria based catalysts have a) much higher sulfur tolerance and b) excellent resistance against Pt sintering when they are compared to the widely used alumina based catalysts.

54 ENVIRONMENTAL SCIENCES↗

Unraveling the relationship between physicochemical properties of NiFeReOx catalysts and the correlated performance toward electrochemical oxygen evolution reaction

NiFeO x catalysts with single site Re dopants exhibit much higher active and stability toward electrochemical oxygen evolution reaction (OER) compared to traditional NiFeO x catalysts. Nevertheless, the relationship between physicochemical properties of NiFeReO x catalysts and the correlated performance toward OER is unclear, which hampers to enhance the OER performance further. Herein, we prepared a series of NiFeReO x catalysts with different physicochemical properties by treating them at different temperatures (up to 350 °C) and then evaluated their performance toward OER. Here, the results show that heat treatment can convert all metal oxidation states to higher values as well as specific surface areas, which are believed to favor real active site generation and OER activity enhancement. A decrease in activity is observed with the temperature increase at the low current range, and the smallest overpotential of 248 mV at 10 mA cm −2 is achieved with the pristine NiFeReO x catalyst. In contrast, the heat-treated samples possess smaller Tafel slopes and lower charge transfer resistance likely due to enhanced intrinsic activity (from higher oxidation states) and conductivity, which facilitate the reaction kinetics and surpass the pristine sample at a large current density. Additionally, the sample treated at 350 °C exhibits a higher activity at 1000 mA cm −2 (1.68 V vs. RHE compared to pristine sample of 1.92 V vs. RHE); however, it manifests a poorer stability compared to the pristine one due to the imbalance of reconstruction/transformations that occurred on the catalyst surface during OER operation. Our work unravels the relationship between physicochemical properties of NiFeReO x catalysts and the correlated OER performance and provides valuable insights for designing NiFeReO x catalysts with high activity and durability.

Catalyst reconstruction↗

Stochastic generation of electrolyzer anode catalyst layers

Here, we introduce a stochastic methodology to reproduce the complex pore structure observed in commercial iridium catalyst layers. This method preserves the α pore (pores smaller than 250 nm) and β pore (pores greater than or equal to 250 nm) regions of the catalyst layer. The morphology of the generated materials was validated by comparing the pore size distributions of generated materials against those obtained from commercial materials imaged using x-ray nano computed tomography. We further demonstrate that the pore size distributions of the generated materials are statistically indistinguishable from the imaged catalyst layers, indicating that the stochastic methodology is capable of accurately reproducing catalyst layer morphology. Pore network modelling was conducted on the generated catalyst materials to simulate single-phase permeability, electrical conductivity, and ionic conductivity, and these properties were found to be within experimentally measured ranges for electrolyzer catalyst layers. Additionally, simulations were performed on the generated materials with varying ionomer and iridium catalyst loadings. As the ionomer loading is added, proton conductivity increases exponentially, which demonstrates the importance of optimizing ionomer loading, considering that these effects will be exacerbated in the hydration and temperature conditions of operating electrolyzers. The stochastic material generation method presented in this work is a powerful tool for the development of novel low loading catalyst layers, where the effect of various structural parameters on electrolyzer performance characteristics can be explored.

36 MATERIALS SCIENCE↗