SEARCH · Search NASA

Results for “Computational fluid dynamics code”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

All sources NASA NTRS DOE OSTI

NASA NTRS2016

Analysis of Low-Speed Stall Aerodynamics of a Swept Wing with Seamless Flaps

Computational fluid dynamics (CFD) analysis was conducted to study the low-speed stall aerodynamics of a Gulfstream G-III airplane (Gulfstream Aerospace Corporation, Savannah, Georgia) swept wing modified with an experimental seamless, compliant flap called the Adaptive Compliant Trailing Edge (ACTE) flap. The stall characteristics of the modified ACTE wing were analyzed and compared with the unmodified, clean wing at the flight speed of 120 knots and altitude of 2300 feet above mean sea level, in free air as well as in ground effect. A polyhedral finite-volume unstructured full Navier-Stokes CFD code, STAR-CCM (registered trademark) plus (CD-adapco [Computational Dynamics Limited, United Kingdom, and Analysis & Design Application Co., United States]), was used. Steady Reynolds-averaged Navier-Stokes CFD simulations were conducted for a clean wing and the ACTE wings at various ACTE deflection angles in free air (-2 degrees, 15 degrees, and 30 degrees) as well as in ground effect (15 degrees and 30 degrees). Solution sensitivities to grid densities were examined. In free air, the ACTE wings are predicted to stall at lower angles of attack than the clean wing. In ground effect, all wings are predicted to stall at lower angles of attack than the corresponding wings in free air. Even though the lift curves are higher in ground effect than in free air, the maximum lift coefficients for all wings are lower in ground effect. Finally, the lift increase due to ground effect for the ACTE wing is predicted to be less than the clean wing.

CFD↗

NASA NTRS2005

Heart Pump Design for Cleveland Clinic Foundation

Through a Lewis CommTech Program project with the Cleveland Clinic Foundation, the NASA Lewis Research Center is playing a key role in the design and development of a permanently implantable, artificial heart pump assist device. Known as the Innovative Ventricular Assist System (IVAS), this device will take on the pumping role of the damaged left ventricle of the heart. The key part of the IVAS is a nonpulsatile (continuous flow) artificial heart pump with centrifugal impeller blades, driven by an electric motor. Lewis is part of an industry and academia team, led by the Ohio Aerospace Institute (OAI), that is working with the Cleveland Clinic Foundation to make IVAS a reality. This device has the potential to save tens of thousands of lives each year, since 80 percent of heart attack victims suffer irreversible damage to the left ventricle, the part of the heart that does most of the pumping. Impeller blade design codes and flow-modeling analytical codes will be used in the project. These codes were developed at Lewis for the aerospace industry but will be applicable to the IVAS design project. The analytical codes, which currently simulate the flow through the compressor and pump systems, will be used to simulate the flow within the blood pump in the artificial heart assist device. The Interdisciplinary Technology Office heads up Lewis' efforts in the IVAS project. With the aid of numerical modeling, the blood pump will address many design issues, including some fluid-dynamic design considerations that are unique to the properties of blood. Some of the issues that will be addressed in the design process include hemolysis, deposition, recirculation, pump efficiency, rotor thrust balance, and bearing lubrication. Optimum pumping system performance will be achieved by modeling all the interactions between the pump components. The interactions can be multidisciplinary and, therefore, are influenced not only by the fluid dynamics of adjacent components but also by thermal and structural effects. Lewis-developed flow-modeling codes to be used in the pump simulations will include a one-dimensional code and an incompressible three-dimensional Navier-Stokes flow code. These codes will analyze the prototype pump designed by the Cleveland Clinic Foundation. With an improved understanding of the flow phenomena within the prototype pump, design changes to improve the performance of the pump system can be verified by computer prior to fabrication in order to reduce risks. The use of Lewis flow modeling codes during the design and development process will improve pump system performance and reduce the number of prototypes built in the development phase. The first phase of the IVAS project is to fully develop the prototype in a laboratory environment that uses a water/glycerin mixture as the surrogate fluid to simulate blood. A later phase of the project will include testing in animals for final validation. Lewis will be involved in the IVAS project for 3 to 5 years.

Source record↗

NASA NTRS1988

Flowfield visualization for SSME hot gas manifold

The objective of this research, as defined by NASA-Marshall Space Flight Center, was two-fold: (1) to numerically simulate viscous subsonic flow in a proposed elliptical two-duct version of the fuel side Hot Gas Manifold (HGM) for the Space Shuttle Main Engine (SSME), and (2) to provide analytical support for SSME related numerical computational experiments, being performed by the Computational Fluid Dynamics staff in the Aerophysics Division of the Structures and Dynamics Laboratory at NASA-MSFC. Numerical results of HGM were calculations to complement both water flow visualization experiments and air flow visualization experiments and air experiments in two-duct geometries performed at NASA-MSFC and Rocketdyne. In addition, code modification and improvement efforts were to strengthen the CFD capabilities of NASA-MSFC for producing reliable predictions of flow environments within the SSME.

Roger, Robert P.↗

NASA NTRS1992

Computations of unsteady multistage compressor flows in a workstation environment

High-end graphics workstations are becoming a necessary tool in the computational fluid dynamics environment. In addition to their graphic capabilities, workstations of the latest generation have powerful floating-point-operation capabilities. As workstations become common, they could provide valuable computing time for such applications as turbomachinery flow calculations. This report discusses the issues involved in implementing an unsteady, viscous multistage-turbomachinery code (STAGE-2) on workstations. It then describes work in which the workstation version of STAGE-2 was used to study the effects of axial-gap spacing on the time-averaged and unsteady flow within a 2 1/2-stage compressor. The results included time-averaged surface pressures, time-averaged pressure contours, standard deviation of pressure contours, pressure amplitudes, and force polar plots.

Gundy-Burlet, Karen L.↗

NASA NTRS1998

Navier-Stokes Computations on Commodity Computers

In this paper we discuss and demonstrate the feasibility of solving high-fidelity, nonlinear computational fluid dynamics (CFD) problems of practical interest on commodity machines, namely Pentium Pro PC's. Such calculations have now become possible due to the progress in computational power and memory of the off-the-shelf commodity computers, along with the growth in bandwidth and communication speeds of networks. A widely used CFD code known as TLNS3D, which was developed originally on large shared memory computers was selected for this effort. This code has recently been ported to massively parallel processor (MPP) type machines, where natural partitioning along grid blocks is adopted in which one or more blocks are distributed to each of the available processors. In this paper, a similar approach is adapted to port this code to a cluster of Pentium Pro computers. The message passing among the processors is accomplished through the use of standard message passing interface (MPI) libraries. Scaling studies indicate fairly high level of parallelism on such clusters of commodity machines, thus making solutions to Navier-Stokes equations for practical problems more affordable.

Vatsa, Veer N.↗

NASA NTRS2013

Long Hole Film Cooling Dataset for CFD Development : Infrared Thermography and Thermocouple Surveys - Part 1

An experiment investigating flow and heat transfer of long (length to diameter ratio of 18) cylindrical film cooling holes has been completed. In this paper, the thermal field in the flow and on the surface of the film cooled flat plate is presented for nominal freestream turbulence intensities of 1.5 and 8 percent. The holes are inclined at 30deg above the downstream direction, injecting chilled air of density ratio 1.0 onto the surface of a flat plate. The diameter of the hole is 0.75 in. (0.01905 m) with center to center spacing (pitch) of 3 hole diameters. Coolant was injected into the mainstream flow at nominal blowing ratios of 0.5, 1.0, 1.5, and 2.0. The Reynolds number of the freestream was approximately 11,000 based on hole diameter. Thermocouple surveys were used to characterize the thermal field. Infrared thermography was used to determine the adiabatic film effectiveness on the plate. Hotwire anemometry was used to provide flowfield physics and turbulence measurements. The results are compared to existing data in the literature. The aim of this work is to produce a benchmark dataset for Computational Fluid Dynamics (CFD) development to eliminate the effects of hole length to diameter ratio and to improve resolution in the near-hole region. In this report, a Time-Filtered Navier Stokes (TFNS), also known as Partially Resolved Navier Stokes (PRNS), method that was implemented in the Glenn-HT code is used to model coolant-mainstream interaction. This method is a high fidelity unsteady method that aims to represent large scale flow features and mixing more accurately.

Shyam, Vikram↗

NASA NTRSDate not supplied

High-Fidelity Simulations of a Quadrotor Vehicle for Urban Air Mobility

High-fidelity computational fluid dynamics simulations have been carried out to analyze NASA’s quadrotor air taxi concept for urban air mobility. High-order accurate schemes, dual-time stepping, and the delayed detached-eddy simulation model have been employed. The flow solver has been loosely coupled with the rotorcraft comprehensive analysis code. The vehicle simulated is a six-passenger quadrotor for air taxi operations. The quadrotor has been simulated in hover and cruise, with flight conditions representative of an air taxi mission. Initially, the quadcopter vehicle is analyzed using low-fidelity tools. Then, a complete analysis using high-fidelity simulations of the quadcopter is performed in conjunction with collective pitch control. Airloads, wake geometry, and performance are studied and compared. A comparison between isolated rotors and complete vehicle simulations is presented. NASA’s quadrotor is one of NASA’s concept vehicles designed in support of aircraft development for vertical take-off and landing air taxi operations.

ARMD↗

NASA NTRS2000

Functionality Improvements to Overaero

The functionality of the overset, static aeroelasticity, Navier-Stokes flow solver OVERAERO was increased by adding capability to the flow solver and enhancing code performance. Improvements were made to the fluids/structure interface, an MLP version of the parallel OVERAERO code was developed, and the OVERAERO-MPI code was ported to the Cray T3E. The OVERFLOW-MPI and OVERAERO-MPI codes were tested successfully on the IPG testbed and a means of reducing communication overhead within OVERFLOW-MPI was investigated. To solve an aeroelastic problem computationally, a structures grid surface definition and a fluids grid surface definition are required. Typically, the structures grid surface has a lower fidelity than the fluids grid surface. Thus, the methods developed to transfer data between the two grid systems are vital to the accuracy and efficiency of the aeroelasticity code. The fluids/structures interface developed for the OVERAERO code was improved to more accurately treat fluids surfaces that bridge between two different structural surfaces. For example, the method allowed the forward portion of a flap track fairing to deform with the wing and the aft end of the fairing to deform with the flap. A tightly-coupled version of the code based on OVERFLOW-MLP was developed to improve code performance on the SGI Origin 2000. This required a new parallelization strategy to couple the fluids and structures codes. The OVERAERO-MPI code was ported to the Cray T3E to extend the usability of the code. The port required extensive use of dynamic memory management techniques to fit large problems within the memory limitations of the T3E. The OVERFLOW-MPI and OVERAERO-MPI codes were tested on the IPG testbed being developed within NASA. For small problems with minimal data transfer between grids, there was little to no performance penalty spreading the computation across two machines. For very large problems, methods were developed to minimize intermachine communication via the grid partitioning scheme. By minimizing the intermachine communication requirements of the problem, it may still be beneficial to run a tightly-coupled flow solver across two machines within the IPG.

Gee, Ken↗

NASA NTRS1995

CFD-Based Design Optimization Tool Developed for Subsonic Inlet

The traditional approach to the design of engine inlets for commercial transport aircraft is a tedious process that ends with a less-than-optimum design. With the advent of high-speed computers and the availability of more accurate and reliable computational fluid dynamics (CFD) solvers, numerical optimization processes can effectively be used to design an aerodynamic inlet lip that enhances engine performance. The designers' experience at Boeing Corporation showed that for a peak Mach number on the inlet surface beyond some upper limit, the performance of the engine degrades excessively. Thus, our objective was to optimize efficiency (minimize the peak Mach number) at maximum cruise without compromising performance at other operating conditions. Using a CFD code NPARC, the NASA Lewis Research Center, in collaboration with Boeing, developed an integrated procedure at Lewis to find the optimum shape of a subsonic inlet lip and a numerical optimization code, ADS. We used a GRAPE-based three-dimensional grid generator to help automate the optimization procedure. The inlet lip shape at the crown and the keel was described as a superellipse, and the superellipse exponents and radii ratios were considered as design variables. Three operating conditions: cruise, takeoff, and rolling takeoff, were considered in this study. Three-dimensional Euler computations were carried out to obtain the flow field. At the initial design, the peak Mach numbers for maximum cruise, takeoff, and rolling takeoff conditions were 0.88, 1.772, and 1.61, respectively. The acceptable upper limits on the takeoff and rolling takeoff Mach numbers were 1.55 and 1.45. Since the initial design provided by Boeing was found to be optimum with respect to the maximum cruise condition, the sum of the peak Mach numbers at takeoff and rolling takeoff were minimized in the current study while the maximum cruise Mach number was constrained to be close to that at the existing design. With this objective, the optimum design satisfied the upper limits at takeoff and rolling takeoff while retaining the desirable cruise performance. Further studies are being conducted to include static and cross-wind operating conditions in the design optimization procedure. This work was carried out in collaboration with Dr. E.S. Reddy of NYMA, Inc.

Source record↗

NASA NTRS2016

Wind-US Users Guide Version 3.0

Wind-US is a computational platform which may be used to numerically solve various sets of equations governing physical phenomena. Currently, the code supports the solution of the Euler and Navier-Stokes equations of fluid mechanics, along with supporting equation sets governing turbulent and chemically reacting flows. Wind-US is a product of the NPARC Alliance, a partnership between the NASA Glenn Research Center (GRC) and the Arnold Engineering Development Complex (AEDC) dedicated to the establishment of a national, applications-oriented flow simulation capability. The Boeing Company has also been closely associated with the Alliance since its inception, and represents the interests of the NPARC User's Association. The "Wind-US User's Guide" describes the operation and use of Wind-US, including: a basic tutorial; the physical and numerical models that are used; the boundary conditions; monitoring convergence; the files that are read and/or written; parallel execution; and a complete list of input keywords and test options. For current information about Wind-US and the NPARC Alliance, please see the Wind-US home page at http://www.grc.nasa.gov/WWW/winddocs/ and the NPARC Alliance home page at http://www.grc.nasa.gov/WWW/wind/. This manual describes the operation and use of Wind-US, a computational platform which may be used to numerically solve various sets of equations governing physical phenomena. Wind-US represents a merger of the capabilities of four CFD codes - NASTD (a structured grid flow solver developed at McDonnell Douglas, now part of Boeing), NPARC (the original NPARC Alliance structured grid flow solver), NXAIR (an AEDC structured grid code used primarily for store separation analysis), and ICAT (an unstructured grid flow solver developed at the Rockwell Science Center and Boeing).

Navier-Stokes equation↗

NASA NTRS2023

Assessment of the Fluid Dynamics Boundary Condition in Ablating or Blowing Flows

Improved models of ablative thermal protection systems have enabled the treatment of materials and fluid behavior in a coupled manner. This paper reports a new approach to modeling the interface between fluid and material, with attention to the conservation of species mass flux and energy on the fluid side of the interface. The general equation is presented and is shown to recover the traditional uncoupled fluid/materials response interface. Including the chemical reaction terms on the CFD side of the interface makes the heat flux exchange independent of the thermodynamic reference state and, therefore, a measurable quantity. Doing so allows the material response solver to take as input the surface heat flux rather than a film coefficient. Removing the film coefficient approximation enables more direct solution of vehicle thermal response but requires consistency in the wall state. The mixing of the shock layer and pyrolysis gas is then computed with finite rate chemistry within the fluid solver. The boundary conditions described have been implemented in the DPLR v4.05.1 code. Char removal is captured using finite rate chemistry in DPLR’s gas surface interaction module. Aspects of coupling these solutions to material response are discussed.

Ablation↗

NASA NTRS2023

Assessment of the Fluid Dynamics Boundary Condition in Ablating or Blowing Flows

Ablation↗

NASA NTRS1982

Experiences with explicit finite-difference schemes for complex fluid dynamics problems on STAR-100 and CYBER-203 computers

Several two- and three-dimensional external and internal flow problems solved on the STAR-100 and CYBER-203 vector processing computers are described. The flow field was described by the full Navier-Stokes equations which were then solved by explicit finite-difference algorithms. Problem results and computer system requirements are presented. Program organization and data base structure for three-dimensional computer codes which will eliminate or improve on page faulting, are discussed. Storage requirements for three-dimensional codes are reduced by calculating transformation metric data in each step. As a result, in-core grid points were increased in number by 50% to 150,000, with a 10% execution time increase. An assessment of current and future machine requirements shows that even on the CYBER-205 computer only a few problems can be solved realistically. Estimates reveal that the present situation is more storage limited than compute rate limited, but advancements in both storage and speed are essential to realistically calculate three-dimensional flow.

Kumar, A.↗

NASA NTRS1983

Improved method for transonic airfoil design-by-optimization

An improved method for use of optimization techniques in transonic airfoil design is demonstrated. FLO6QNM incorporates a modified quasi-Newton optimization package, and is shown to be more reliable and efficient than the method developed previously at NASA-Ames, which used the COPES/CONMIN optimization program. The design codes are compared on a series of test cases with known solutions, and the effects of problem scaling, proximity of initial point to solution, and objective function precision are studied. In contrast to the older method, well-converged solutions are shown to be attainable in the context of engineering design using computational fluid dynamics tools, a new result. The improvements are due to better performance by the optimization routine and to the use of problem-adaptive finite difference step sizes for gradient evaluation.

Kennelly, R. A., Jr.↗

NASA NTRS1983

Improved method for transonic airfoil design-by-optimization

An improved method for use of optimization techniques in transonic airfoil design is demonstrated. FLO6QNM incorporates a modified quasi-Newton optimization package, and is shown to be more reliable and efficient than the method developed previously at NASA-Ames, which used the COPES/CONMIN optimization problem. The design codes are compared on a series of test cases with known solutions, and the effects of problem scaling, proximity of initial point to solution, and objective function precision are studied. In contrast to the older method, well-converged solutions are shown to be attainable in the context of engineering design using computational fluid dynamics tools, a new result. The improvements are due to better performance by the optimization routine and to the use of problem-adaptive finite difference step sizes for gradient evaluation.

Kennelly, R. A., Jr.↗

NASA NTRS1998

Reduction and Analysis of Phosphor Thermography Data With the IHEAT Software Package

Detailed aeroheating information is critical to the successful design of a thermal protection system (TPS) for an aerospace vehicle. This report describes NASA Langley Research Center's (LaRC) two-color relative-intensity phosphor thermography method and the IHEAT software package which is used for the efficient data reduction and analysis of the phosphor image data. Development of theory is provided for a new weighted two-color relative-intensity fluorescence theory for quantitatively determining surface temperatures on hypersonic wind tunnel models; an improved application of the one-dimensional conduction theory for use in determining global heating mappings; and extrapolation of wind tunnel data to flight surface temperatures. The phosphor methodology at LaRC is presented including descriptions of phosphor model fabrication, test facilities and phosphor video acquisition systems. A discussion of the calibration procedures, data reduction and data analysis is given. Estimates of the total uncertainties (with a 95% confidence level) associated with the phosphor technique are shown to be approximately 8 to 10 percent in the Langley's 31-Inch Mach 10 Tunnel and 7 to 10 percent in the 20-Inch Mach 6 Tunnel. A comparison with thin-film measurements using two-inch radius hemispheres shows the phosphor data to be within 7 percent of thin-film measurements and to agree even better with predictions via a LATCH computational fluid dynamics solution (CFD). Good agreement between phosphor data and LAURA CFD computations on the forebody of a vertical takeoff/vertical lander configuration at four angles of attack is also shown. In addition, a comparison is given between Mach 6 phosphor data and laminar and turbulent solutions generated using the LAURA, GASP and LATCH CFD codes. Finally, the extrapolation method developed in this report is applied to the X-34 configuration with good agreement between the phosphor extrapolation and LAURA flight surface temperature predictions. The phosphor process outlined in the paper is believed to provide the aerothermodynamic community with a valuable capability for rapidly obtaining (4 to 5 weeks) detailed heating information needed in TPS design.

Merski, N. Ronald↗

NASA NTRS1991

Computation of supersonic jet mixing noise for an axisymmetric CD nozzle using k-epsilon turbulence model

The turbulent mixing noise of a supersonic jet is calculated for a round convergent-divergent nozzle at the design pressure ratio. Aerodynamic computations are performed using the PARC code with a k-epsilon turbulence model. Lighthill's acoustic analogy combined with Ribner's assumption is adopted. The acoustics solution is based upon the methodology followed by GE in the MGB code. The source correlation function is expressed as a linear combination of second-order tensors. Assuming separable second-order correlations and incorporating Batchelor's isotropic turbulence model, the source term was calculated from the kinetic energy of turbulence. A Gaussian distribution for the time-delay of correlation was introduced. The computational fluid dynamics (CFD) solution was used to obtain the source strength as well as the characteristic time-delay of correlation. The effect of sound/flow interaction was incorporated using the high frequency asymptotic solution to Lilley's equation for axisymmetric geometries. Acoustic results include sound pressure level directivity and spectra at different polar angles. The aerodynamic and acoustic results demonstrate favorable agreement with experimental data.

Khavaran, Abbas↗

NASA NTRS1992

Computation of supersonic jet mixing noise for an axisymmetric CD nozzle using k-epsilon turbulence model

Khavaran, A.↗