Search NASA⌕ Search

SEARCH · Search NASA

Results for “Contacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Simultaneous shunt protection and back contact formation for CdTe solar cells with single wall carbon nanotube layers

Thin film photovoltaic (PV) devices and modules prepared by commercial processes can be severely compromised by through-device low resistance electrical pathways. The defects can be due to thin or missing semiconductor material, metal diffusion along grain boundaries, or areas containing diodes with low turn-on potentials. We report the use of single wall carbon nanotube (SWCNT) layers to enable both protection against these defects and back contact formation for CdTe PV devices. Samples prepared with a SWCNT back contact exhibited good efficiency and did not require shunt protection, while devices prepared without shunt protection using a standard metal back contact performed poorly. We describe the mechanism by which the SWCNT layer functions. In addition to avoiding the need for shunt protection by other means, the SWCNT film also provides a route to higher short circuit currents.

14 SOLAR ENERGY↗

Determination of the solid surface critical exponent β{sub 1} from contact-angle variation on approach to a wetting transition: Cyclohexane/aniline/quartz

The three-phase contact angle (θ) for the system cyclohexane/aniline/quartz has been measured from drop shapes as a function of temperature on approach to the cyclohexane/aniline upper consolute solution temperature T{sub c}. The experiments employed exacting criteria previously established for thermodynamic-quality measurements at fluid interfaces. A first-order wetting transition from partial wetting to complete wetting was observed at a temperature T{sub w}, 2.12 K below T{sub c}. The contact angle vanishes at T{sub w}, scaling as cos θ ∼ |T − T{sub c}|{sup β{sub 1}−μ} for T < T{sub w} and cos θ = 1.0 for T{sub w} < T < T{sub c}. The experimental results give a value for β{sub 1} = 0.74 ± 0.03, in agreement with theoretical calculations. The data clearly rule out higher order contributions to the change in the contact angle near the critical point for this system. These results are in marked contrast to previous measurements on this system from measurements of capillary rise and meniscus curvature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of a time-resolved non-contact scanning diffuse optical imaging system exploiting fast-gated single-photon avalanche diode detection

We present a system for non-contact time-resolved diffuse reflectance imaging, based on small source-detector distance and high dynamic range measurements utilizing a fast-gated single-photon avalanche diode. The system is suitable for imaging of diffusive media without any contact with the sample and with a spatial resolution of about 1 cm at 1 cm depth. In order to objectively assess its performances, we adopted two standardized protocols developed for time-domain brain imagers. The related tests included the recording of the instrument response function of the setup and the responsivity of its detection system. Moreover, by using liquid turbid phantoms with absorbing inclusions, depth-dependent contrast and contrast-to-noise ratio as well as lateral spatial resolution were measured. To illustrate the potentialities of the novel approach, the characteristics of the non-contact system are discussed and compared to those of a fiber-based brain imager.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Fabrication of Ohmic contact on semi-insulating 4H-SiC substrate by laser thermal annealing

The Ni contact layer was deposited on semi-insulating 4H-SiC substrate by magnetron sputtering. The as-deposited samples were treated by rapid thermal annealing (RTA) and KrF excimer laser thermal annealing (LTA), respectively. The RTA annealed sample is rectifying while the LTA sample is Ohmic. The specific contact resistance (ρ{sub c}) is 1.97 × 10{sup −3} Ω·cm{sup 2}, which was determined by the circular transmission line model. High resolution transmission electron microscopy morphologies and selected area electron diffraction patterns demonstrate that the 3C-SiC transition zone is formed in the near-interface region of the SiC after the as-deposited sample is treated by LTA, which is responsible for the Ohmic contact formation in the semi-insulating 4H-SiC.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Wide range local resistance imaging on fragile materials by conducting probe atomic force microscopy in intermittent contact mode

An imaging technique associating a slowly intermittent contact mode of atomic force microscopy (AFM) with a home-made multi-purpose resistance sensing device is presented. It aims at extending the widespread resistance measurements classically operated in contact mode AFM to broaden their application fields to soft materials (molecular electronics, biology) and fragile or weakly anchored nano-objects, for which nanoscale electrical characterization is highly demanded and often proves to be a challenging task in contact mode. Compared with the state of the art concerning less aggressive solutions for AFM electrical imaging, our technique brings a significantly wider range of resistance measurement (over 10 decades) without any manual switching, which is a major advantage for the characterization of materials with large on-sample resistance variations. After describing the basics of the set-up, we report on preliminary investigations focused on academic samples of self-assembled monolayers with various thicknesses as a demonstrator of the imaging capabilities of our instrument, from qualitative and semi-quantitative viewpoints. Then two application examples are presented, regarding an organic photovoltaic thin film and an array of individual vertical carbon nanotubes. Both attest the relevance of the technique for the control and optimization of technological processes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Impact of incomplete metal coverage on the electrical properties of metal-CNT contacts: A large-scale ab initio study

Using a dedicated combination of the non-equilibrium Green function formalism and large-scale density functional theory calculations, we investigated how incomplete metal coverage influences two of the most important electrical properties of carbon nanotube (CNT)-based transistors: contact resistance and its scaling with contact length, and maximum current. These quantities have been derived from parameter-free simulations of atomic systems that are as close as possible to experimental geometries. Physical mechanisms that govern these dependences have been identified for various metals, representing different CNT-metal interaction strengths from chemisorption to physisorption. Our results pave the way for an application-oriented design of CNT-metal contacts.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nanosecond laser scribing of CIGS thin film solar cell based on ITO bottom contact

Cu(In,Ga)Se2 (CIGS) thin films, a promising photovoltaic architecture, have mainly relied on Molybdenum for the bottom contact. However, the opaque nature of Molybdenum (Mo) poses limitations in module level fabrication by laser scribing as a preferred method for interconnect. We examined the P1, P2, and P3 laser scribing processes on CIGS photovoltaic architecture on the indium tin oxide (ITO) bottom contact with a cost-effective nanosecond pulsed laser of 532 nm wavelength. Laser illuminated from the substrate side, enabled by the transparent bottom contact, facilitated selective laser energy deposition onto relevant interfaces towards high-quality scribing. Parametric tuning procedures are described in conjunction with experimental and numerical investigation of relevant mechanisms, and preliminary mini-module fabrication results are also presented.

Kuk, Seungkuk↗

A “polar contact” tent for reduced perturbation and improved performance of NIF ignition capsules

In indirectly driven Inertial Confinement Fusion implosions conducted on the National Ignition Facility (NIF), the imploding capsule is supported in a laser-heated radiation enclosure (called a “hohlraum”) by a pair of very thin (~15–45 nm) plastic films (referred to as a “tent”). Even though the thickness of these tents is a small fraction of that of the spherical capsule ablator (~165 μm), both numerical simulations as well as experiments indicate that this capsule support mechanism results in a large areal density (ρR) perturbation on the capsule surface at the contact point where the tent departs from the capsule. As a result, during deceleration of the deuterium-tritium (DT) fuel layer, a jet of the dense ablator material penetrates and cools the fuel hot spot, significantly degrading the neutron yield (resulting in only ~10%–20% of the unperturbed 1-D yield). In this article, we present a hypothesis and supporting design simulations of a new “polar contact” tent support system, which reduces the contact area between the tent and the capsule and results in a significant improvement in the capsule performance. Simulations predict a ~70% increase in neutron yield over that for an implosion with a traditional tent support. Overall, an initial demonstration experiment was conducted on the NIF and produced highest ever recorded primary DT neutron yield among all layered DT implosions with plastic ablators on the NIF, though more experiments are needed to comprehensively study the effect of the polar tent on implosion performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Superlubricity in rolling/sliding contacts

Rolling element bearings and gears are critical components of mechanical systems such as wind turbines and automotive engines and transmissions that use oil-based lubricants. Oil-based lubricants used in these applications many times needs periodical replacement, which not only add more cost but also affects overall productivity. More importantly, the used oil generates hazardous waste creating huge environmental problem. In this study, we demonstrated that nanomaterials can be employed as solid lubricants in combination with diamond like carbon (DLC) films in dry nitrogen environment under rolling/sliding contacts. Using micro-pitting rig (MPR) that generally used to test and qualify materials and lubricants for bearings and gear systems for industrial applications, we have tested diamond like carbon (DLC) material pairs in an oil-free, dry nitrogen environment along with two dimensional (2D) MoS2 combined with nanodiamond as a solid lubricant. We show that superlubricity (traction coefficient of friction is 0.003) was achieved through the formation of a carbon rich superlubricious tribolayer at the interface reducing the overall friction by a minimum of 20 times and no surface damage as compared to Steel-Steel contacts lubricated with oil (0.06-0.07). The current work paves the way for developing oil-free solid lubricants in a variety of applications involving rolling/sliding contacts.

36 MATERIALS SCIENCE↗

A microchip microcontroller-based transducer controller for non-contact scanning probe microscopy with phase-locked loop, amplitude, and Q control

An inexpensive yet versatile transducer controller for non-contact scanning probe microscopy (SPM) based on a PIC32 microcontroller from Microchip Technology, Inc is described. In addition to feedback control using the amplitude or phase of the signal from the non-contact transducer, the controller includes a phase-locked loop for frequency-shift feedback, as well as fixed-amplitude, quality factor (Q) control, and self-excitation modes. Apart from the input amplifiers, output buffers, and the Q-control circuit, all other functions of the controller are instantiated in software on the microchip, enabling rapid changes in operating parameters if needed. The controller communicates with a host personal computer via a simple serial connection. The controller has been tested with a quartz tuning-fork transducer but can be used with any oscillating non-contact transducer.

47 OTHER INSTRUMENTATION↗

Schottky contacts to N-polar GaN with SiN interlayer for elevated temperature operation

In this Letter, we unveil the high-temperature limits of N-polar GaN Schottky contacts enhanced by a low-pressure chemical vapor deposited (LPCVD) SiN interlayer. Compared to conventional Schottky diodes, the insertion of a 5 nm SiN lossy dielectric interlayer in-between Ni and N-polar GaN increases the turn-on voltage (V ON ) from 0.4 to 0.9 V and the barrier height ($\phi_B$) from 0.4 to 0.8 eV. This modification also reduces the leakage current at zero bias significantly: at room temperature, the leakage current in the conventional Schottky diode is >103 larger than that observed in the device with the SiN interlayer, while at 200 °C, this ratio increases to 105. Thus, the rectification ratio (ION/IOFF) at ±1.5 V reduces to less than one at 250 °C for the conventional Schottky diode, whereas for SiN-coated diodes, rectification continues until 500 °C. The I–V characteristics of the diode with an SiN interlayer can be recovered after exposure to 400 °C or lower. Contact degradation occurs at 500 °C, although devices are not destroyed yet. Here, we report N-polar GaN Schottky contact operation up to 500 °C using an LPCVD SiN interlayer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Direct Contacts Between Extracellular Membrane-Proximal Domains are Required for VEGF Receptor Activation and Cell Signaling

Structural analyses of the extracellular region of stem cell factor (SCF) receptor (also designated KIT) in complex with SCF revealed a sequence motif in a loop in the fourth Ig-like domain (D4) that is responsible for forming homotypic receptor contacts and for ligand-induced KIT activation and cell signaling. An identical motif was identified in the most membrane-proximal seventh Ig-like domain (D7) of vascular endothelial growth factor receptor 1 (VEGFR1), VEGFR2, and VEGFR3. In this report we demonstrate that ligand-induced tyrosine autophosphorylation and cell signaling via VEGFR1 or VEGFR2 harboring mutations in critical residues (Arg726 or Asp731) in D7 are strongly impaired. We also describe the crystal structure of D7 of VEGFR2 to a resolution of 2.7 {angstrom}. The structure shows that homotypic D7 contacts are mediated by salt bridges and van der Waals contacts formed between Arg726 of one protomer and Asp731 of the other protomer. The structure of D7 dimer is very similar to the structure of D4 dimers seen in the crystal structure of KIT extracellular region in complex with SCF. The high similarity between VEGFR D7 and KIT D4 in both structure and function provides further evidence for common ancestral origins of type III and type V RTKs. It also reveals a conserved mechanism for RTK activation and a novel target for pharmacological intervention of pathologically activated RTKs.

59 BASIC BIOLOGICAL SCIENCES↗

NEAR-CONTACT BINARIES WITH MASS TRANSFER: V473 CASSIOPEIAE AND II PERSEI

Photometric solutions of two short period close binaries, V473 Cas and II Per, are derived with the 2003 version Wilson-Van Hamme code. It is shown that V473 Cas is a semidetached system with the primary component or the secondary component at its critical Roche Lobe, while II Per is a marginal contact binary system with both components filling their critical Roche Lobes, but with a large temperature difference between the two components. Both systems belong to near-contact binaries with the light curves enhanced around the left shoulder of secondary minimum, which can be explained by hot spots on the secondary components due to the mass transfer via a stream hitting the facing surface of the secondary components. The orbital period investigations based on all available times of light minimum show a secular period existing in these two targets decreasing at the rate of dP/dt = -7.61 x 10{sup -8} days yr{sup -1} for V473 Cas and dP/dt = -7.54 x 10{sup -8} days yr{sup -1} for II Per. The decrease of the orbital period can be the result of mass transfer from the primary component to the secondary one, which is consistent with the asymmetric light curves of V473 Cas and II Per. Therefore, V473 Cas and II Per are other examples displaying evidence of mass transfer between the two components. We have collected NCBs with secular period variation and find that almost all SD1-type NCBs show decreasing periods and enhancing luminosity on the left shoulder of secondary minimum in their light curves. So the semidetached configuration with the lobe filling primary is more plausible for V473 Cas. Furthermore, the detected enhancing amplitude of luminosity for SD2-type NCBs is smaller than other types of NCBs, which implies that the mass transfer from the primary component to the secondary one is stronger than the transfer in opposite direction. With the orbital period decrease, V473 Cas and II Per will evolve into overcontact binaries with true thermal contact.

79 ASTRONOMY AND ASTROPHYSICS↗

A CHARGE-COUPLED DEVICE PHOTOMETRIC STUDY OF SOUTH HEMISPHERIC CONTACT BINARY AE PHOENICIS

The complete charge-coupled device light curves in B, V, R, and I bands of the short-period binary system, AE Phe, are presented. It is found that the light curves of AE Phe belong to typical EW-type light variation. Photometric solutions were derived by using the 2003 version of the Wilson-Devinney code. It showed that AE Phe is a W-subtype shallow-contact system (f = 14.6%({+-}0.5%)) with a mass ratio of q = 2.5491({+-}0.0092). The temperature difference between the two components is 227 K. Analysis of the O - C curve suggests that the period of AE Phe shows a long-term continuous increase at a rate of dP/dt = +6.17({+-}0.44) x 10{sup -8} days year{sup -1}. The long-term period increase, the marginal-contact configuration, and the astrophysical parameters of the binary system, all suggest that it is a shallow-contact binary undergoing a thermal relaxation oscillation evolving into a detached binary.

79 ASTRONOMY AND ASTROPHYSICS↗

WZ CEPHEI: A CLOSE BINARY AT THE BEGINNING OF CONTACT PHASE

Photometric photoelectric data of the short-period close binary system, WZ Cephei, are presented. A new photometric analysis with the 2003 version of the Wilson-Devinney method confirmed that it is a shallow contact binary (f {approx} 13.3%) with a high level of spot activity on the primary component. Combining new determined times of light minimum with the others published in the literature, the period change of the binary star is investigated. A periodic variation, with a period of 34.2 years and an amplitude of 0fd013, was discovered to be superimposed on a long-term period decrease (dP/dt = -8.8 x 10{sup -8} days year{sup -1}). Both the secular period decrease and the shallow contact configuration suggest that this binary system is at the beginning of contact phase. It is on the way to evolving into a normal overcontact phase via secular angular momentum loss and/or mass transfer from the more massive component to the less massive one. The period oscillation can be explained either by the light-time effect due to the presence of a third body or by magnetic activity. On the one hand, if it is caused by the light-time effect, the mass and the orbital radius of the additional body should be m {sub 3} = 0.17 M {sub sun} and a {sub 3} = 26.6 AU, respectively, when this body is coplanar to the orbit of the eclipsing pair. On the other hand, since the system shows high levels of spot activity, the period oscillation may be explained as a consequence of magnetic cycles. In this case, the required variation of the quadrupole moment is calculated to be 9.2 x 10{sup 49} g cm{sup 2}.

79 ASTRONOMY AND ASTROPHYSICS↗

ORBITAL PERIOD CHANGES AND THEIR EVOLUTIONARY STATUS FOR THE WEAK-CONTACT BINARIES. III. AO CAMELOPARDALIS AND AH TAURI

In this paper, we presented multicolor photometric observations for two eclipsing binaries, AO Camelopardalis and AH Tauri, obtained on 2008 December 16 and 17. Using the Wilson-Devinney Code, the photometric solution of AH Tau was determined from our new CCD data. The mass ratio and the fill-out factor are q = 0.503({+-}0.003) and f = 10.8%({+-}0.1%), respectively. This indicates that AH Tau is in weak contact. For the weak-contact binary AO Cam, BVI light curves clearly show a difference in the heights of the maxima (i.e., the O'Connell effect), which may be explained by spot activity. By analyzing the O - C curves for AO Cam and AH Tau, it is found that the orbital periods appear to show a secular period decrease with a cyclic variation. The observed period modulation is {delta}P/P {approx} 10{sup -6}. For AO Cam, the cyclic oscillation with a short period of 7.63({+-}0.07) yr and a low amplitude of 0fd0019({+-}0fd0003) may be preferably attributed to the cyclic magnetic activity. The period and amplitude of the cyclic variation for AH Tau are 45.8({+-}1.1) yr and 0fd0171({+-}0fd0005), which may more likely result from the light-time effect via a third body. The secular period decrease rates are dP/dt = -1.26({+-}0.04) x 10{sup -7} days yr {sup -1} for AO Cam and dP/dt = -6.98({+-}0.07) x 10{sup -8} days yr {sup -1} for AH Tau. This kind of period decrease can be plausibly explained by the mass transfer from the primary to the secondary, and may result in the system evolving into a deep contact configuration.

79 ASTRONOMY AND ASTROPHYSICS↗

PHOTOMETRIC STUDY OF THE NEAR CRITICAL CONTACT SYSTEM, GSC 3355 0394

GSC 3355 0394 has an EB-type light curve, which is dominated by hot and cool spot activities. It displays night-to-night variations in light-curve shapes. The period study yields six new times of minimum light and the first precision ephemeris, HJD T{sub min}I = 2, 454, 408.9547 {+-} 0.0017 + 0.4621603 {+-} 0.0000008d*E. VR{sub c}I{sub c} standard magnitudes are presented. BVRI Wilson synthetic light-curve solutions are calculated for both a Mode 4 (V1010 Oph-type, semidetached, more massive component filling its Roche lobe) configuration and a Mode 3, contact configuration (fill-out 100% or critical contact). The critical contact is the lowest residual solution. Four major spot regions are needed to model this binary, at least one is evidently a stream spot.

79 ASTRONOMY AND ASTROPHYSICS↗

WZ CYGNI: A MARGINAL CONTACT BINARY IN A TRIPLE SYSTEM?

We present new multiband CCD photometry for WZ Cyg made on 22 nights in two observing seasons of 2007 and 2008. Our light-curve synthesis indicates that the system is in poor thermal contact with a fill-out factor of 4.8% and a temperature difference of 1447 K. Including our 40 timing measurements, a total of 371 times of minimum light spanning more than 112 yr were used for a period study. Detailed analysis of the O-C diagram showed that the orbital period has varied by a combination of an upward parabola and a sinusoid. The upward parabola means continuous period increase and indicates that some stellar masses are thermally transferred to the more massive primary star at a rate of about 5.80 x 10{sup -8} M{sub sun} yr{sup -1}. The sinusoidal variation with a period of 47.9 yr and a semi-amplitude of 0.008 days can most likely be interpreted as the light-travel-time effect due to the existence of a low-mass M-type tertiary companion with a projected mass of M{sub 3}sin i{sub 3} = 0.26 M{sub sun}. We examined the evolutionary status of WZ Cyg from the absolute dimensions of the eclipsing pair. It belongs to the marginal contact binary systems before the broken contact phase, consisting of a massive primary star with spectral type F4 and a secondary star with type K1.

79 ASTRONOMY AND ASTROPHYSICS↗