Search NASA⌕ Search

SEARCH · Search NASA

Results for “Launch Methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Application of Probabilistic Methods to Assess Risk Due to Resonance in the Design of J-2X Rocket Engine Turbine Blades

The LOX-Hydrogen J-2X Rocket Engine, which is proposed for use as an upper-stage engine for numerous earth-to-orbit and heavy lift launch vehicle architectures, is presently in the design phase and will move shortly to the initial development test phase. Analysis of the design has revealed numerous potential resonance issues with hardware in the turbomachinery turbine-side flow-path. The analysis of the fuel pump turbine blades requires particular care because resonant failure of the blades, which are rotating in excess of 30,000 revolutions/minutes (RPM), could be catastrophic for the engine and the entire launch vehicle. This paper describes a series of probabilistic analyses performed to assess the risk of failure of the turbine blades due to resonant vibration during past and present test series. Some significant results are that the probability of failure during a single complete engine hot-fire test is low (~1%) because of the small likelihood of resonance, but that the probability increases to around 30% for a more focused turbomachinery-only test because all speeds will be ramped through and there is a greater likelihood of dwelling at more speeds. These risk calculations have been invaluable for use by program management in deciding if risk-reduction methods such as dampers are necessary immediately or if the test can be performed before the risk-reduction hardware is ready.

Brown, Andrew M.↗

ATK Launch Vehicle (ALV-X1) Liftoff Acoustic Environments: Prediction vs. Measurement

Launched from the Mid-Atlantic Regional Spaceport (MARS) Pad 01B on August 22, 2008, the ATK Launch Vehicle (ALV-X1) provided an opportunity to measure liftoff acoustic noise data. Predicted lift-off acoustic environments were developed by both NASA MSFC and ATK engineers. ATK engineers developed predictions for use in determining vibro-acoustic loads using the method described in the monograph NASA SP-8072. The MSFC ALV-X1 lift-off acoustic prediction was made with the Vehicle Acoustic Environment Prediction Program (VAEPP). The VAEPP and SP-8072 methods predict acoustic pressures of rocket systems generally scaled to existing rocket motor data based upon designed motor or engine characteristics. The predicted acoustic pressures are sound-pressure spectra at specific positions on the vehicle. This paper presents the measured liftoff acoustics on the vehicle and tower. This data is useful for the ALV-X1 in validating the pre-launch environments and loads predictions.

Houston, J.↗

3D Printing In Zero-G ISS Technology Demonstration

The National Aeronautics and Space Administration (NASA) has a long term strategy to fabricate components and equipment on‐demand for manned missions to the Moon, Mars, and beyond. To support this strategy, NASA and Made in Space, Inc. are developing the 3D Printing In Zero‐G payload as a Technology Demonstration for the International Space Station (ISS). The 3D Printing In Zero‐G experiment ('3D Print') will be the first machine to perform 3D printing in space. The greater the distance from Earth and the longer the mission duration, the more difficult resupply becomes; this requires a change from the current spares, maintenance, repair, and hardware design model that has been used on the International Space Station (ISS) up until now. Given the extension of the ISS Program, which will inevitably result in replacement parts being required, the ISS is an ideal platform to begin changing the current model for resupply and repair to one that is more suitable for all exploration missions. 3D Printing, more formally known as Additive Manufacturing, is the method of building parts/objects/tools layer‐by‐layer. The 3D Print experiment will use extrusion‐based additive manufacturing, which involves building an object out of plastic deposited by a wire‐feed via an extruder head. Parts can be printed from data files loaded on the device at launch, as well as additional files uplinked to the device while on‐orbit. The plastic extrusion additive manufacturing process is a low‐energy, low‐mass solution to many common needs on board the ISS. The 3D Print payload will serve as the ideal first step to proving that process in space. It is unreasonable to expect NASA to launch large blocks of material from which parts or tools can be traditionally machined, and even more unreasonable to fly up multiple drill bits that would be required to machine parts from aerospace‐grade materials such as titanium 6‐4 alloy and Inconel. The technology to produce parts on demand, in space, offers unique design options that are not possible through traditional manufacturing methods while offering cost-effective, high‐precision, low‐unit on‐demand manufacturing. Thus, Additive Manufacturing capabilities are the foundation of an advanced manufacturing in space roadmap. The 3D Printing In Zero‐G experiment will demonstrate the capability of utilizing Additive Manufacturing technology in space. This will serve as the enabling first step to realizing an additive manufacturing, print‐on‐demand "machine shop" for long‐duration missions and sustaining human exploration of other planets, where there is extremely limited ability and availability of Earth‐based logistics support. Simply put, Additive Manufacturing in space is a critical enabling technology for NASA. It will provide the capability to produce hardware on‐demand, directly lowering cost and decreasing risk by having the exact part or tool needed in the time it takes to print. This capability will also provide the much‐needed solution to the cost, volume, and up‐mass constraints that prohibit launching everything needed for long‐duration or long‐distance missions from Earth, including spare parts and replacement systems. A successful mission for the 3D Printing In Zero‐G payload is the first step to demonstrate the capability of printing on orbit. The data gathered and lessons learned from this demonstration will be applied to the next generation of additive manufacturing technology on orbit. It is expected that Additive Manufacturing technology will quickly become a critical part of any mission's infrastructure.

Werkheiser, Niki↗

Atlas base drag study

Proposed changes to Atlas booster stage drag simulation method for improving agreement between predicted and actual flight data

ASCENT TRAJECTORY↗

VAPEPS Management Center

VAPEPS is a computer program that utilizes statistical energy analysis (SEA) theory and SEA extrapolation methods to predict the vibroacoustic environments in complex systems.

vibroacoustic↗

The Solid Rocket Motor Slag Population: Results of a Radar-Based Regressive Statistical Evaluation

Solid rocket motor (SRM) slag has been identified as a potential source of man-made orbital debris. The possibility that SRMs (in addition to generating dust particles in the sub-millimeter range) may generate particles up to centimeters in size has caused concern regarding their contribution to the debris environment. Returned surfaces from space do not have sufficient area or exposure time to provide a clear picture of the SRM millimeter and centimeter debris population. Currently, radar observation is probably the only way to collect data showing the debris contribution from SRMs. Such observation is used to sample the debris environment, but it is difficult to obtain accurate orbital elements for the detected debris objects. NASA has developed several models to describe the different orbital debris populations, based on assumed debris production mechanisms to create clouds of debris objects that can be propagated in time. The NASA model, LEGEND (LEO-to-GEO Environment Debris), functions as a time-tested debris model for most debris sources. However, the current LEGEND model does not include contributions from the SRM population. An SRM model has recently been developed by NASA, based on purely theoretical details of SRM production and known SRM launches, but verification with hard data is needed. Because the detections of individual SRM objects cannot be deterministically separated from the total debris observed by radar, the validation of the SRM model can only be done by combining it with the LEGEND breakup model and comparing it with data. By applying observational constraints, the degree of SRM slag contribution to the environment may be estimated. This serves as an observationally sound method from which to calibrate a purely theoretical model into something more realistic. For this study, we use the populations observed by the Haystack radar from 1996 to present. For the SRM debris, we use a historical database of SRM launches, propellant masses, and estimated locations and times of tailoff to produce and propagate the SRM debris clouds. Comparisons with radar data from the ensuing years were made, and the SRM model was altered with respect to size and mass production of slag particles to reflect the populations estimated from the data. The result is a model SRM population that fits within the bounds of the observed environment and estimates of the production and contribution of SRM debris to the environment.

Horstman, Matthew F.↗

Validation of the Corcos Model for the Space Launch System using Unsteady Pressure Sensitive Paint

During atmospheric ascent launch vehicles (LVs) experience large dynamic loads at transonic conditions where aerodynamic buffet is most critical. To estimate buffet loads, coupled loads analyses typically utilize suitable forcing functions, called buffet forcing functions (BFFs). One of the key buffet environment contributors is the turbulent boundary layer (TBL) on the LV outer skin. The TBL-induced fluctuating pressures can be estimated using the widely-accepted Corcos model. In the context of transonic buffet, the performance of this model is not well established, partly because of lack of data. To fill this gap, NASA recently acquired extremely high-spatial-density data for the Space Launch System (SLS) vehicle, using the unsteady pressure sensitive paint (uPSP) optical measurement technique. A methodology is developed for validation of the Corcos model using these unique data, with a focus on the LV-design application. The model hypotheses are verified and the model parameters are empirically tuned. For selected panels on the vehicle, BFF coherence factors are derived based on the Corcos model and the associated panel BFFs are compared to uPSP data. It is shown that the modeled BFFs are in agreement with direct integration of uPSP data, except for regions where pressure fluctuations are spatially nonuniform. In those regions, the Corcos-based BFFs exhibit inherent limitations of BFF estimation methods that rely on discrete pressure measurements.

buffet↗

Space Launch System Unsteady Forces Developed from Unsteady-Pressure-Sensitive-Paint–Based Corcos Model Parameters

During atmospheric ascent, launch vehicles (LVs) experience large dynamic loads at transonic conditions where aerodynamic buffet is most critical. To estimate buffet loads, coupled loads analyses typically utilize suitable forcing functions, called buffet forcing functions (BFFs). One of the key buffet environment contributors is the turbulent boundary layer (TBL) on the LV outer skin. The TBL-induced fluctuating pressures can be estimated using the widely-accepted Corcos model. In the context of transonic buffet, the performance of this model is not well established, partly because of lack of data. To fill this gap, NASA recently acquired extremely high-spatial-density data for the Space Launch System (SLS) vehicle, using the unsteady pressure sensitive paint (uPSP) optical measurement technique. A methodology is developed for validation of the Corcos model using these unique data, with a focus on the LV-design application. The model hypotheses are verified and the model parameters are empirically tuned. For selected panels on the vehicle, BFF coherence factors are derived based on the Corcos model and the associated panel BFFs are compared to uPSP data. It is shown that the modeled BFFs are in agreement with direct integration of uPSP data, except for regions where pressure fluctuations are spatially nonuniform. In those regions, the Corcos-based BFFs exhibit inherent limitations of BFF estimation methods that rely on discrete pressure measurements.

buffet↗

On-Orbit Performance of the NOAA-21 Advanced Technology Microwave Sounder (ATMS)

The Advanced Technology Microwave Sounder (ATMS) instrument provides sounding measurements of Earth’s atmosphere to collect temperature and water vapor data for NOAA’s Joint Polar Satellite System (JPSS) program. ATMS is a total-power passive microwave radiometer with 22 channels spanning a frequency range from 22 to 183 GHz. A general description of the ATMS instrument is detailed in [1]. Three ATMS units are currently on-orbit. The Suomi National Polar-orbiting Partnership (SNPP) unit was launched in 2011 and the NOAA-20 (previously JPSS-1) unit was launch in 2017. Both SNPP and NOAA-20 ATMS units are currently operational and the data is used for numerical weather prediction (NWP) models. The NOAA-21 (formerly JPSS-2) ATMS unit was launched on November 10, 2022 from Vandenberg Space Force Base in California [2]. The ATMS instrument began generating radiance data on November 21, 2022. At the time of this abstract NOAA-21 ATMS is currently completing on-orbit commissioning and checkout activities; it is expected that the commissioning activities will be complete by the IGARSS 2023 conference. This paper will focus on the on-orbit performance of the NOAA-21 ATMS instrument based on measurements and activities from the commissioning period. Comparisons will be made to specifications and to expected performance based on pre-launch test activities. Pre-launch JPSS-2 (NOAA-21) ATMS performance is detailed in [4]. Additionally, the NOAA-21 performance will be compared to the on-orbit performance of the SNPP and NOAA-21 ATMS units. The post-launch performance of SNPP ATMS is detailed in [1][5][6][7]. The post-launch performance of NOAA-20 ATMS is detailed in [5][7][8]. On-orbit performance is evaluated through data collects from nominal mission operations as well as specific post-launch tests and spacecraft maneuvers. Nominal mission operations can be used to evaluate parameters such as instrument thermal stability, Noise Equivalent Delta Temperature (NEDT)/radiometric sensitivity, geolocation, inter-channel noise correlation, striping, and radiometric bias and stability. Shortly after instrument activation, the instrument thermal stability as measured from onboard temperature sensors is evaluated to demonstrate stable and steady-state behavior. Methods for computing NEDT are described in [9][10][11]. Passive geolocation measurements are performed using the coastline inflection point (CIP) method, described in [8][12]. The striping index, used as a metric to quantify striping, is the ratio of along-track variance to cross-track variance of the observed brightness temperature [4][8][14]. Inter-channel noise correlation has been previously reported for SNPP and NOAA-20 [1][8]. Dedicated post-launch tests and spacecraft maneuvers are utilized during the commissioning phase for further evaluation of on-orbit instrument performance. These activities provide information on the optimal space view selection, noise power spectral density (PSD), gain stability, scan bias, interference from onboard transmitters, reflector emissivity, active geolocation, and radiometric bias and stability detection methods. The optimal space view selection is used to determine which of ATMS space view sectors is preferred for minimizing contamination of the space view [1]. Point and stare testing is used to generate noise PSD and gain stability information, as described in [1][8]. Spacecraft roll and pitch maneuvers allow the ATMS to view different zones, including deep space, and the data can be used to provide information on scan biases and antenna sidelobe contamination [1][8]. The pitch maneuver can also be used to assess interference from onboard Ka-band transmitters and reflector emissivity [8]. Active geolocation is evaluated as a method for geolocation, described in [15].

Edward Kim↗

A Microphone Phased Array for Launch Acoustics Application

A new, portable, phased array of microphones is built at NASA Ames Research Center specifically for the harsh environment encountered in launch acoustics applications. It uses 70 rugged, piezo-electric, dynamic pressure sensors optimally distributed on a 10.5ft diameter open frame dome structure. The open frame is light yet robust to sustain the high wind load of typical seaside launch pads, and the blast and acoustic loads from the launch. A 200-ft long cable bundle carries the microphone signals to a weather-protected electronic cabinet containing the data acquisition system, computers, and other equipment. The array is equipped with an infra-red camera and a visible wavelength camera for imaging the launch site. The beamformed noise maps will be superimposed on the video footages collected by the cameras for correct identification of the noise sources. The array is tested with very loud noise sources to determine the beamforming ability. Multiple mathematical models, such as the conventional beamforming, functional beamforming, spectral element method etc. are used to determine the minimum spatial resolution of the sound sources that can be measured at different frequencies. Additionally, the array hardware is being tested for different environmental conditions and electro-magnetic compliance. The immediate goal is to use the array for NASA’s Artemis/SLS vehicle that will be launched from a newly built Mobile Launch platform and a modified launch pad.

microphone phased-array↗

Thermal Analysis Methods for Aerobraking Heating

As NASA begins exploration of other planets, a method of non-propulsively slowing vehicles at the planet, aerobraking, may become a valuable technique for managing vehicle design mass and propellant. An example of this is Mars Reconnaissance Orbiter (MRO), which will launch in late 2005 and reach Mars in March of 2006. In order to save propellant, MRO will use aerobraking to modify the initial orbit at Mars. The spacecraft will dip into the atmosphere briefly on each orbit, and during the drag pass, the atmospheric drag on the spacecraft will slow it, thus lowering the orbit apoapsis. The largest area on the spacecraft, and that most affected by the heat generated during the aerobraking process, is the solar arrays. A thermal analysis of the solar arrays was conducted at NASA Langley, to simulate their performance throughout the entire roughly 6-month period of aerobraking. Several interesting methods were used to make this analysis more rapid and robust. Two separate models were built for this analysis, one in Thermal Desktop for radiation and orbital heating analysis, and one in MSC.Patran for thermal analysis. The results from the radiation model were mapped in an automated fashion to the Patran thermal model that was used to analyze the thermal behavior during the drag pass. A high degree of automation in file manipulation as well as other methods for reducing run time were employed, since toward the end of the aerobraking period the orbit period is short, and in order to support flight operations the runs must be computed rapidly. All heating within the Patran Thermal model was combined in one section of logic, such that data mapped from the radiation model and aeroheating model, as well as skin temperature effects on the aeroheating and surface radiation, could be incorporated easily. This approach calculates the aeroheating at any given node, based on its position and temperature as well as the density and velocity at that trajectory point. Run times on several different processors, computer hard drives, and operating systems (Windows versus Linux) were evaluated.

Amundsen, Ruth M.↗

Exploration Mission Tasks: A Technical Manual

This technical manual is an abridgement of the Generalizable Skills and Knowledge for Exploration Missions (NASA/CR-2018-22045) report (Stuster et al., 2019), describing research conducted under Cooperative Agreement 80NSSC18K0042 for the Human Factors and Behavioral Performance Element, Human Research Program, located at the National Aeronautics and Space Administration’s (NASA) Johnson Space Center. The research identified tasks that will be conducted by human crew during an expedition to Mars, and the abilities, skills, and knowledge that will be required of crew members. The 3-year study uses research methods that were developed to analyze the work performed by a variety of civilian and military occupational specialties and is consistent with Human Factors methods. The work began by developing a comprehensive inventory of 1,125 tasks that are likely to be performed during the 12 phases of the first human expeditions to Mars, from launch to landing 30 months later. Sixty subject matter experts (SMEs) rated expedition tasks in terms of (likely) frequency of performance, difficulty to learn, and importance to mission success; a fourth metric (criticality), was derived by summing the mean ratings of the three dimensions. Seventy-two SMEs placed the physical, cognitive, and social abilities necessary to perform the tasks in order of importance for specialist domains identified by the task analysis. The research team then identified: 1) Abilities, skills, and knowledge that can be retained and generalized across tasks and 2) Implications for crew size and composition. Study results also led to recommendations concerning equipment, habitats, and procedures for exploration-class space missions. Note: The full-mission task inventory was developed during a comprehensive review of documentation and concepts of operations. It was understood by the study team that the tasks were based on currently available information, and that the tools, equipment, propulsion methods, and/or other aspects of actual human expeditions to Mars might be different from those described here, as a consequence of technological development and evolving Mars Design Reference Missions. The purpose and scope of this technical manual is to present the core, actionable information that resulted from this research. The abridged format is intended to address the needs of development and research teams to quickly access, discern, and use the information in the course of their exploration-related work.

Brandin Munson↗

Applications and Benefits of GNSS for Lunar Exploration

This paper explores the role of Global Navigation Satellite Systems (GNSS) in NASA's lunar exploration plans. Robust position, navigation and timing (PNT) at the Moon will rely on a variety of measurement sources, each with its own advantages and disadvantages. The best navigation solution will depend on mission type, the phase within each mission, the state of lunar infrastructure development at the time and a host of other considerations. No single method will provide all PNT for all scenarios, but GNSS offers a continuously available, flight-proven source of navigation and timing with unique features that make it a valuable option. As NASA launches a new era of lunar exploration missions in 2021, development of the supporting navigation architecture is underway. This paper describes the role GNSS could or will play in the components of NASA's lunar exploration plans: the Artemis missions designed to return humans to the lunar surface, the Gateway platform orbiting near the Moon that will host astronauts as well as science and technology payloads, and the robotic lander missions administered by the Commercial Lunar Payload Services (CLPS) program. GNSS-based autonomous navigation has the potential to dramatically expand lunar exploration capabilities. Through the use of GNSS and GNSS-like augmentations, navigation performance could be improved while simultaneously reducing operational complexity relative to conventional, ground-based navigation methods. As NASA begins to implement its lunar exploration plans this year and assemble the enabling communications and navigation infrastructure, GNSS will provide an important part of the diverse measurements required for robust lunar PNT.

Benjamin W Ashman↗

High Efficiency Cascade Solar Cells

This report summarizes the main work performed by New Mexico State University and University of Houston on a DOE sponsored project High Efficiency Cascade Solar Cells. The main tasks of this project include materials synthesis, characterization, theoretical calculations, organic solar cell device fabrication and test. The objective of this project is to develop organic nano-electronic-based photovoltaics. Carbon nanotubes and organic conjugated polymers were used to synthesize nanocomposites as the new active semiconductor materials that were used for fabricating two device architectures: thin film coating and cascade solar cell fiber. Chemical vapor deposition technique was employed to synthesized a variety of carbon nanotubes (single-walled CNT, doubled-walled CNT, multi-walled CNT, N-doped SWCNT, DWCNT and MWCNT, and B-doped SWCNT, DWCNT and MWCNT) and a few novel carbon structures (CNT-based nanolance, nanocross and supported graphene film) that have potential applications in organic solar cells. Purification procedures were developed for removing amorphous carbons from carbon nanotubes, and a controlled oxidation method was established for partial truncation of fullerene molecules. Carbon nanotubes (DWCNT and DWCNT) were functionalized with fullerenes and dyes covalently and used to form nanocomposites with conjugated polymers. Biologically synthesized Tellurium nanotubes were used to form composite with the conjugated polymers as well, which generated the highest reported optical limiting values from composites. Several materials characterization technique including SEM/TEM, Raman, AFM, UV-vis, adsorption and EDS were employed to characterize the physical and chemical properties of the carbon nanotubes, the functionalized carbon nanotubes and the nanocomposites synthesized in this project. These techniques allowed us to have a spectroscopic and morphological control of the composite formation and to understand the materials assembled. A parallel 136-CPU Beowulf computer cluster was launched intended to be used as the main computational tool for the theoretical part of this project. The mechanism of surface carboxylation of pristine and defective carbon nanotubes were studied using the computation method. Theoretical studies of boron- and nitrogen-doped carbon nanotubes functionalized with chemical groups, and CdSe/ZnSe, ZnSe/CdSe, CdTe/ZnTe, and ZnTe/CdTe core-shell semiconductor nanoparticles embedded in electroactive polymers were also carried out. We have successfully fabricated singular champion cells with Voc of 0.6 V and Jsc of 15 mA, and developed the pixel cells and with a working areas over 25mm 2 , 2.5 % efficiency for a multicell arrangement, and a stability of 40% of their initial efficiency after 11,000 minutes. We have also demonstrated the feasibility of using a gold film as an alternative semi-transparent electrode for organic solar cell applications. An efficiency of 1.9 % (J SC of 7.01 mA/cm 2 , V OC of 0.55 V, FF of 0.49) can be reached by using the gold film as an anode instead of ITO. Two new vertical organic solar cell architectures: stack cells and wrap cells, suitable as an alternative to planar devices were developed as well. We have proved the feasibility of replacing ITO with more traditional metals without hindering performance, and developed natural encapsulation techniques during device fabrication. Optical modeling of the stack cells was also performed to enhance our understanding of this device configuration.

14 SOLAR ENERGY↗

3D Printing in Zero-G ISS Technology Demonstration

The National Aeronautics and Space Administration (NASA) has a long term strategy to fabricate components and equipment on-demand for manned missions to the Moon, Mars, and beyond. To support this strategy, NASA and Made in Space, Inc. are developing the 3D Printing In Zero-G payload as a Technology Demonstration for the International Space Station. The 3D Printing In Zero-G experiment will be the first machine to perform 3D printing in space. The greater the distance from Earth and the longer the mission duration, the more difficult resupply becomes; this requires a change from the current spares, maintenance, repair, and hardware design model that has been used on the International Space Station up until now. Given the extension of the ISS Program, which will inevitably result in replacement parts being required, the ISS is an ideal platform to begin changing the current model for resupply and repair to one that is more suitable for all exploration missions. 3D Printing, more formally known as Additive Manufacturing, is the method of building parts/ objects/tools layer-by-layer. The 3D Print experiment will use extrusion-based additive manufacturing, which involves building an object out of plastic deposited by a wire-feed via an extruder head. Parts can be printed from data files loaded on the device at launch, as well as additional files uplinked to the device while on-orbit. The plastic extrusion additive manufacturing process is a low-energy, low-mass solution to many common needs on board the ISS. The 3D Print payload will serve as the ideal first step to proving that process in space. It is unreasonable to expect NASA to launch large blocks of material from which parts or tools can be traditionally machined, and even more unreasonable to fly up specialized manufacturing hardware to perform the entire range of function traditionally machining requires. The technology to produce parts on demand, in space, offers unique design options that are not possible through traditional manufacturing methods while offering cost-effective, high-precision, low-unit on-demand manufacturing. Thus, Additive Manufacturing capabilities are the foundation of an advanced manufacturing in space roadmap.

Johnston, Mallory M.↗

A double peak in the seasonality of California's photosynthesis as observed from space

Solar-induced chlorophyll fluorescence (SIF) has been shown to be a powerful proxy for photosynthesis and gross primary productivity (GPP). The recently launched TROPOspheric Monitoring Instrument (TROPOMI) features the required spectral resolution and signal-to-noise ratio to retrieve SIF from space. Here, we present a downscaling method to obtain 500 m spatial resolution SIF over California. We report daily values based on a 14 d window. TROPOMI SIF data show a strong correspondence with daily GPP estimates at AmeriFlux sites across multiple ecosystems in California. We find a linear relationship between SIF and GPP that is largely invariant across ecosystems with an intercept that is not significantly different from zero. Measurements of SIF from TROPOMI agree with MODerate Resolution Imaging Spectroradiometer (MODIS) vegetation indices – the normalized difference vegetation index (NDVI), enhanced vegetation index (EVI), and near-infrared reflectance of vegetation index (NIR$_v$) – at annual timescales but indicate different temporal dynamics at monthly and daily timescales. TROPOMI SIF data show a double peak in the seasonality of photosynthesis, a feature that is not present in the MODIS vegetation indices. The different seasonality in the vegetation indices may be due to a clear-sky bias in the vegetation indices, whereas previous work has shown SIF to have a low sensitivity to clouds and to detect the downregulation of photosynthesis even when plants appear green. We further decompose the spatiotemporal patterns in the SIF data based on land cover. The double peak in the seasonality of California's photosynthesis is due to two processes that are out of phase: grasses, chaparral, and oak savanna ecosystems show an April maximum, while evergreen forests peak in June. An empirical orthogonal function (EOF) analysis corroborates the phase offset and spatial patterns driving the double peak. The EOF analysis further indicates that two spatiotemporal patterns explain 84 % of the variability in the SIF data. Results shown here are promising for obtaining global GPP at sub-kilometer spatial scales and identifying the processes driving carbon uptake.

54 ENVIRONMENTAL SCIENCES↗

Detection of hydrogen chloride gas in air

Launch vehicle effluent (LVE) monitoring is part of NASA's overall tropospheric and stratospheric environmental program. Following nine techniques are evaluated and developed in report: bubbler method, pH measurements, indicator tubes, microcoulometers, modified condensation nuclei counter, dual-isotope absorption, gas-filter correlation, chemiluminescent nitric oxide detection, chemiluminescent luminol-oxidation detection.

Gregory, G. L.↗

Voyager design and flight loads comparison

Estimates of flight loads for Voyager 1 and Voyager 2 are summarized. These member loads are obtained by using the measured flight accelerations at the launch vehicle/spacecraft interface as forcing functions for the Voyager mathematical model. The flight loads are compared to the Voyager design loads obtained from the shock spectra/impedance method and to the loads obtained using space vehicle transient loads analysis. Finally, based on these data, an assessment of the shock spectra/impedance loads method used for Voyager is presented.

Chen, J. C.↗