Search NASA⌕ Search

SEARCH · Search NASA

Results for “Layered Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Effect of Al and Cr Content on Air and Steam Oxidation of FeCrAl Alloys and Commercial APMT Alloy

To develop the next generation of accident-tolerant fuel cladding for light-water nuclear reactors, wrought FeCrAlY alloys with varying amounts of Cr and Al and commercial Kanthal APMT alloy were evaluated for short-term (4 h) oxidation resistance in steam and air at 1200–1475 °C. Model alloys with lower Cr contents and higher Al contents were evaluated in this paper as lower Cr contents are desirable for radiation damage resistance during operation. As expected, a synergistic effect was found between the Cr and Al contents to enable protective Al 2 O 3 formation under these conditions. Characterization of the alumina scales formed in steam found that the scale morphology was affected by the alloy Y content and detailed scanning transmission electron microscopy (STEM) detected Y segregation along scale grain boundaries at 1200 °C. However, after 4 h at 1475 °C, Y and Hf were not segregated to the oxide grain boundaries formed on APMT and the scale had a single layer structure. Finally, compared to oxidation in air, STEM characterization of the outer scale showed differences in the Fe and Cr distributions in steam.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Metal-organic frameworks based on magnesium(II): adsorption and luminescence properties

Two new metal-organic frameworks based on magnesium(II) ions, [Mg{sub 4}(bdc){sub 3}(dma){sub 6}(NO{sub 3}){sub 2}]•DMA (1; bdc is 1,4-benzenedicarboxylate; dma, DMA is N,N-dimethylacetamide) and [Mg{sub 3}(bpdc){sub 3}(nmp){sub 4}] (2; bpdc is 4,4´-biphenyldicarboxylate; nmp is N-methylpyrrolidone), were synthesized in DMA or NMP, respectively. According to the single-crystal X-ray diffraction data, compound 1 is built of binuclear carboxylate units {Mg_2(O_2CR)_3}, which were previously not observed in metal-organic frameworks. Compound 2 is based on trinuclear carb oxylate units {Mg_3(O_2CR)_6}. Compound 1 has a layered structure (hcb topology), whereas compound 2 has a distorted three-dimensional cubic structure (pcu topology). The phase purity and chemical identity of the compounds were confirmed by IR spectroscopy, thermogravimetry, elemental analysis, and powder X-ray diffraction. Photoluminescence properties of both compounds are indicative of intraligand charge-transfer transitions of one (for 1) or two (for 2) types. Textural characteristics of an activated sample of 1 were measured by nitrogen and hydrogen adsorption at 77 K and by carbon dioxide adsorption at 195 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Impact of Rolling at Temperature on Conductivity and Texture in Nanolamellar Cu/Nb Bimetallic Composites

We report warm rolling is used to identify whether reductions in dislocation content would provide a significant impact on conductivity in accumulatively roll-bonded Cu-Nb nanolaminates. In addition, the impact of temperature on mechanical properties and interfacial texture is also quantified. Although temperature has a strong effect on dislocation content and mechanical properties, it is shown that length scale and volume fraction are most critical to defining the conductivity of the nanolaminate. Rolling at temperature reduced the flow stress of the material while maintaining the interfacial and layer structure, indicating that warm rolling can increase the ability to process the nanolaminates without reducing conductivity.

36 MATERIALS SCIENCE↗

A Review: Microstructural and Phase Evolution in Alloys during Extended Plastic Deformation

Materials in service and during processing are often subjected to plastic deformation. For multi-phase metallic alloys, simple geometric models and atomistic simulations suggest that two distinctive regimes in these materials’ evolution during deformation exist. At low strains, evolutions are often dominated by the kinetic roughening of interfaces, which results from the superdiffusive transport of matter in sheared crystals. Furthermore, at high strains and temperatures where thermal diffusion is sluggish, on the other hand, shearing- induced forced atomic mixing dominates these evolutions, resulting in significantly enhanced solubility. Distinguishing these two regimes is shown to provide a convenient framework for rationalizing and analyzing recent experiments and simulations on wear of layered structures in the low strain-regime and nonequilibrium phase co-existence and self-organization in highly immiscible or reactive alloy systems in the high-strain regime.

36 MATERIALS SCIENCE↗

Effect of combined local variations in elastic and inelastic energy losses on the morphology of tracks in ion-irradiated materials

A judicious choice of irradiation parameters and experimental methodology allowed the visualization of the tracks created by swift heavy ions in pyrochlores over the entire ion trajectories. Several peculiarities were observed: a layered structure of tracks composed of an amorphous core surrounded by a strained crystalline envelope, a change of the track diameter as a function of the ion slowing down, a loss of parallelism of tracks, a transformation from continuous to discontinuous regime, and an increasing contribution of elastic collisions at large depths. These observations are compared to the respective amount of electronic and nuclear energy losses.

Correlation↗

Exsolution of NiCo alloys over Ruddlesden-Popper perovskite for mild electrochemical synthesis of ammonia on protonic ceramic electrochemical cells

Ammonia synthesis from renewable energies on protonic ceramic electrochemical cells (PCECs) shows great potential. The primary challenges in ammonia synthesis on PCECs include sluggish catalytic activity, competition from the hydrogen evolution reaction, and unsatisfactory durability of the cathode, which is the active site of ammonia generation. Here, in this study, we report an elaborate design of the cathode with an intended formula of Pr 4 Ni 1.79 Co 1.2R u 0.01 O 10-δ , where NiCo alloy nanoparticles are exsolved from Ruddlesden-Popper perovskite substrates after the reduction in 5 % H 2 /Ar at 400 °C for 1 h, for electrocatalysis of the nitrogen reduction reaction to ammonia. The host material Pr 4 Ni 1.8 Co 1.2 O 10-δ with embeddable layered structure and stability was deliberately chosen to fix the Ru cation and maximize the catalytic activity of NiCo. Also, density functional theory calculations suggest that Ru doping provides an optimal balance between structural stability and redox activity, facilitating the controlled exsolution of NiCo nanoparticles and enhancing catalytic performance. As a result, the composite electrode with exsolved NiCo alloy and abundant oxygen vacancies on fuel-electrode-supported PCECs achieves a superior electrochemical activity towards ammonia synthesis: a peak ammonia formation rate of 27.84 μg h −1 cm −2 and excellent Faradaic efficiencies of 62.6 % at 350 °C.

30 DIRECT ENERGY CONVERSION↗

Dynamic Wettability Alteration of Calcite, Silica and Illite Surfaces in Subsurface Environments: A Case Study of Asphaltene Self-Assembly at Solid Interfaces

A basic understanding of dynamic wettability alteration at complex solid interfaces in varying fluidic environments representative of the subsurface environments is essential for engineering field-scale strategies to enhance energy recovery while reducing environmental impacts. In this study, we characterize dynamic wettability alteration at solid surfaces (e.g., calcite, silica and illite) resulting from the self-assembly and adsorption of polyaromatic macromolecules known as asphaltenes in heptane and toluene solvents at 200 bar and 313 K using classical molecular dynamics simulations. These conditions are chosen to be representative of the subsurface environments. On adding asphaltenes, the equilibrium contact angles on calcite, silica and illite surfaces which are in the range of 25–34° increased to 69–79°. The adsorption and self-assembly of asphaltene molecules on the solid surfaces and the accumulation on water/hydrocarbon interfaces reduces the spreading distances of water molecules and enhances the hydrophobicity of the solid surfaces. Moreover, the accumulation of asphaltene molecules at the water/liquid hydrocarbon interfaces results in a reduction of the interfacial tension of water/heptane and water/toluene, thus stabilizing the water droplet. The enhanced surface hydrophobicity contributes to the formation of layered structures of heptane and toluene close to the solid surfaces and reduces the self-diffusivities of these molecules close to the surface.

42 ENGINEERING↗

Defect-mediated, thermally-activated encapsulation of metals at the surface of graphite

Here, we show that 3 metals – Dy, Ru, and Cu – can form multilayer intercalated (encapsulated) islands at the graphite (0001) surface if 2 specific conditions are met: Defects are introduced on the graphite terraces to act as entry portals, and the metal deposition temperature is well above ambient. Focusing on Dy as a prototype, we show that surface encapsulation is much different than bulk intercalation, because the encapsulated metal takes the form of bulk-like rafts of multilayer Dy, rather than the dilute, single-layer structure known for the bulk compound. Carbon-covered metallic rafts even form for relatively unreactive metals (Ru and Cu) which have no known bulk intercalation compound.

36 MATERIALS SCIENCE↗

Vacancy-driven variations in the phonon density of states of fast neutron irradiated nuclear graphite

Research examining radiation damage and its effects in graphite began in the 1940’s during the development of moderated nuclear reactors. Interest in this topic is expanding because of emerging applications associated with fullerenes and carbon nanostructures as well as its long-standing use as a fission moderator. In this work, we report the measurements of the full phonon density of states of irradiated nuclear graphite using inelastic neutron scattering experiments at room temperature. The samples were previously exposed to different levels of neutron doses and irradiation temperatures. The phonon density of states of perfect and defected graphite supercells including different configurations of vacancies and interstitials were calculated using first-principles direct method. Despite high neutron irradiation doses, the scattering measurements show that the induced damage is localized, and the layered structure is preserved. In conclusion, a comparison of the measured phonon densities of states of irradiated samples with those calculated of defected supercells indicates that the main changes observed are mainly attributed to formation of vacancies.

36 MATERIALS SCIENCE↗

Specific molecular design of polycarboxylate polymers exhibiting optimal compatibility with clay contaminants in concrete

Highlights: • Allyl ether-based PCEs with short side chain length and low side chain density presented superior clay resistance. • PCEs with medium side chain density exhibited best clay robustness when compared at the absolute dosed quantities. • The proportion of PCE being intercalated into the layered structure of clay was quantified. It is widely recognized that the dispersing ability of polycarboxylate superplasticizers (PCEs) could be hindered due to the presence of clay contaminants in concrete. In this study, a series of allyl ether-based polycarboxylate superplasticizers possessing short polyethylene glycol side chains was successfully synthesized and probed for their clay tolerance. The resulting PCE polymers were characterized via Size Exclusion Chromatography (SEC) to obtain their molecular properties. Thereafter, their dispersing ability was probed in the absence and presence of sodium bentonite. Allyl ether-based polycarboxylate (APEG) polymers possessing short side chains were found to exhibit enhanced clay resistance as compared to that of conventional MPEG PCEs holding long pendant chains. The mode of interaction between APEG PCEs and bentonite was investigated via sorption and XRD measurements. The data revealed that APEG PCEs possessing a lower side chain density intercalate less into the interlayer space of bentonite than those exhibiting higher side chain density.

36 MATERIALS SCIENCE↗

Organo-montmorillonite Barrier Layers Formed by Combustion: Nanostructure and Permeability

Self-assembly of nanoparticles into barrier layers has been the most cited theoretical explanation for the significant reduction in flammability often noted for nanocomposites formed from polymers and montmorillonite organoclays. Both mass and heat transport reductions have been credited for such improvements, and in most cases a coupled mechanism is expected. To provide validation for early models, new model barrier layers were produced from organoclays, and these barrier layers subjected to novel permeability analysis to obtain a flux. The effects of surfactant, temperature and pressure on barrier layer structure were examined. XRD versus TGA results suggest that chemical degradation of four different organoclays and physical collapse on heating are not correlated. Addition of pressure as low as 7kPa also altered the structure produced. Permeability of Ar through the ash was found to be sensitive to structural change/self assembly of high aspect ratio MMT nanoparticles. Actual fluxes ranged from 0.139 to 0.151 mol(m2.sec)-1, values which will provide useful limits in verifying models for the coupled contribution of mass and heat transfer to flammability parameters such as peak heat release rate.

36 MATERIALS SCIENCE↗

In-service corrosion and grain boundary oxidation in neutron-irradiated 316 stainless steel baffle-former bolts

Reactor core internal components such as baffle-former bolts (BFBs) are subjected to significant mechanical stress, corrosive environment, and neutron irradiation from the reactor core during the plant operation. Over the long operation period, these conditions lead to potential degradation and of the bolts. In this work, characterization was performed on the oxidized surface of stainless steel BFBs harvested from a commercial pressurized water reactor (PWR) after 40 years of operation. The analysis shows that a complex multilayered surface oxide with six identified layers formed that is different from 2-layer structure commonly observed in model experiments. The oxide varies by composition – predominantly Fe, Cr, and Ni, grain size, and phase, and has features resembling both unirradiated and radiation/ corrosion experiments likely due to the low radiation flux compared to ion-irradiation or the test reactor radiation. In addition, grain boundary oxidative attack featured a pathway for Fe and other elements to move from the metal matrix to the outermost oxide. In conclusion, the results help assess PWR lifetime extension, put into context previous experimental studies, and provide input for designing experiments combining radiation and corrosion effects.

Baffle-former bolt↗

Micromagnetic simulations with periodic boundary conditions: Hard-soft nanocomposites

Here, we developed a micromagnetic method for modeling magnetic systems with periodic boundary conditions along an arbitrary number of dimensions. The main feature is an adaptation of the Ewald summation technique for evaluation of long-range dipolar interactions. The method was applied to investigate the hysteresis process in hard-soft magnetic nanocomposites with various geometries. The dependence of the results on different micromagnetic parameters was studied. We found that for layered structures with an out-of-plane hard phase easy axis the hysteretic properties are very sensitive to the strength of the interlayer exchange coupling, as long as the spontaneous magnetization for the hard phase is significantly smaller than for the soft phase. The origin of this behavior was discussed. Additionally, we investigated the soft phase size optimizing the energy product of hard-soft nanocomposites.

36 MATERIALS SCIENCE↗

Creep behavior of an additively manufactured 9Cr steel in the as-built condition

Limited studies have evaluated the creep behavior of additively manufactured (AM) ferritic-martensitic (FM) steels. This work investigated the creep behavior of a 9Cr FM steel fabricated by powder blown directed energy deposition (DED) technique. Here, the creep testing at 550–650 °C and 150 MPa for the specimens along the deposition direction in the as-built condition, together with corresponding microstructural characterization, revealed a threshold temperature between 600 and 625 °C, below which the steel has creep resistance comparable with Grade 91 cross-welds and noticeably greater than 9Cr-1Mo steel. The threshold temperature distinguishes the creep behavior in two regimes differentiated in creep activation energy, creep deformation, and failure mechanism. Unlike the creep rupture surface ~45° from the loading direction when tested above the threshold temperature, the creep rupture for testing below the threshold temperature resembles type IV failure in the cross-welds of ferritic steels. The DED-induced layer structure in the as-built steel played a significant role on the change of creep behavior.

36 MATERIALS SCIENCE↗

Effect of Composition on the Voltage Fade Phenomenon in Lithium-, Manganese-Rich xLiMnO 3 •(1-x)LiNi a Mn b Co c O 2 : A Combinatorial Synthesis Approach

The effect of composition on the voltage fade phenomenon was probed using combinatorial synthesis methods. In compositions that have the general formula, (Li 2 MnO 3 ) a (LiNiO 2 ) b (LiMnO 2 ) c (LiCoO 2 ) d , where 0 ≤ a≤0.83, 0.15 ≤ b ≤ 0.42, 0 ≤ c ≤ 0.85, and 0 ≤ d ≤ 0.30 (a + b + c + d = 1), the dependence of features in the x-ray diffraction pattern and of voltage fade on composition were identified and mapped. The observed values of voltage fade indicated that it displayed some sensitivity to composition, but that the sensitivity was not large. The values of voltage fade were found to be amenable to statistical modeling. The model indicated that it may be possible to lower the value of voltage fade below 0.01% by adjusting the composition of the system; however, the composition is not expected to have the layered–layered structure.

combinatorial synthesis↗

Effect of overcharge on Li(Ni 0.5 Mn 0.3 Co 0.2 )O 2 /Graphite lithium ion cells with poly(vinylidene fluoride) binder. I - Microstructural changes in the anode

Cells based on NMC/graphite, containing poly(vinylidene difluoride) (PVDF) binders in the positive and negative electrodes, were systematically overcharged to 100, 120, 140, 160, 180, and 250% state-of-charge (SOC). At 250% SOC the cell vented. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) of the anodes showed several state-of-overcharge-dependent trends. Starting at 120% SOC, dendrites appeared and increased in concentration as the SOC increased. Dendrite morphology appeared to be dependent on whether the active material was on the “dull” or “shiny” side of the copper collector. Significantly more delamination of the active material from the collector was seen on the “shiny” side of the collector particularly at 180 and 250% SOC. Transition metals were detected at 120% SOC and increased in concentration as the SOC increased. Finally, there was considerable spatial heterogeneity in the microstructures across each laminate with several regions displaying complex layered structures.

25 ENERGY STORAGE↗

Aging gracefully? Investigating iridium oxide ink's impact on microstructure, catalyst/ionomer interface, and PEMWE performance

Here, in this study, we conducted a thorough investigation of the impact of aging iridium oxide (IrO 2 ) perfluorosulfonic acid ionomer ink for up to 14 days on the properties of the ink and the resulting catalyst layers. We examined ink properties, such as zeta potential, dynamic light scattering (DLS), density, surface tension, and rheology, as functions of ink aging time. To evaluate the microstructure and catalyst/ionomer interface, we employed transmission electron microscopy (TEM), X-ray scattering, and X-ray photoelectron spectroscopy (XPS) techniques. Furthermore, we assessed the effect of ink aging on the performance of proton exchange membrane water electrolyzers (PEMWEs). Our findings reveal that most ink properties remain stable for 14 days. The variations in PEMWE cell performance are minimal, and no clear trend is observed in relation to ink aging time. This study demonstrates that the effects of aging the inks for 14 days on ink properties, catalyst layer structure, catalyst/ionomer interface, and PEMWE performance are negligible, indicating a substantial time window after ink preparation without any significant changes in its properties. These insights provide crucial guidance for the commercial production and coating processes of ink, which is necessary for scaling up PEM technologies to meet future demand.

30 DIRECT ENERGY CONVERSION↗